HP 15-f010dx: Power 15-f010dx HP on error code 50790400

Similar Questions

• HP G62 - 340US Black screen on power on, no corresponding led error code

  Hey all,.

  Having a problem with my laptop HP G62-340US. The computer will continue to feed on, but the screen does not light, but the caps lock light has a constant slow continuous flashing. The indicator light next to the charging port is orange, as the light next to the wireless button. (There is no NumLock on the keyboard of a light)

  I looked at the link to HP support for this issue, located here:

  http://support.HP.com/us-en/document/c01443366

  But was unable to find my specific situation. Any help or idea would be greatly appricieated.

  Thank you!

  Try to start the machine without the battery and connected to the power adapter. Try to boot the machine with a single chip memory installed (if you have two). Try changing the location of the chip memory if you don't have one. Do a hard reset by removing the battery, power adapter, pressing the power button for 1 minute, reconnect the battery and power adapter, and then try again. If this does not work, you will have a video chip problem that would require a reflow (I know this isn't your model, but it shows you what may be involved):

  http://www.YouTube.com/watch?feature=player_detailpage & v = bnkQNmKauEc #t = 4S

  Good shops use pistols temperature controlled at worst and stations Infra red reflow for more accurate results.  The video was just to give you an idea what may be wrong.

  http://www.YouTube.com/watch?feature=player_detailpage & v = wEVv7p - JDc #t = 8 S

• Tecra S2: Power Saver is often an error Code 0 x 40

  A fairly new model Tecra S2 PTS20E-01Y011DU gives often when using of a fatal error in the program to save energy with the error "this program will be closed' code 0 x 40

  Hello

  I don't know if this will solve the problem but first step you can do is to remove the energy saver, restart the device and try to install it again.

• Tecra M9 - no power orange light error code sequence

  Hello

  I have a Tecra m9 laptop and when I try to turn it on, it blinks with a light orange in this sequence:

  6 short flashes, short 1 long blink, 1 blink, a ditch, and then it repeats.

  Does anyone know what is the problem?
  Any advice would be greatly appreciated.

  See you soon.

  What you see flashes code. The flashing provides an error code. Short means 0 and 1 long.

  The hexadecimal code can be read by the service partner. The blink code will be sent when the microcontroller detects a problem with the power supply. Unfortunately you can not do anything alone. Contact the closest partner in your country and ask for help.

  All you can try right now is to disconnect battery and start the laptop with AC power only.

• Saver 0x47f on power satellite fatal error code

  Hello

  I have a problem with energy saving on my satellite.

  When windows starts up a box appears saying ' program error fatal toshiba power saver will end. 0x47f error code»

  I tried to use the cd tols and utilities to try to reinstall the program saving energy, but when I click on setup on the interface, a box pops up saying

  C:\WINDOWS\SYSTEM32\AUTEXEC. NT. The system file is not for windows applications running msdos and Microsoft. Choose close to terminate the application.

  I tried to install from the msdos also command prompt but no luck it has the same message.

  Can anyone help?

  Hello

  This error message can occur if one or more of the following files are missing or damaged:
  -Config.nt
  -Autoexec.nt
  -Command.com

  I found this info useful here in this Microsoft Knowledge base article
  http://support.Microsoft.com/kb/324767

  try to repair the Autoexec.nt file and after new reboot you might to reinstall the Toshiba Power saver again!

• Portege R100 stoped working - the power LED flashes error codes

  I have a R100 that has suddenly stopped working.
  The power led (clear amber with the image of the power wire) flashes what appears to be an error code of 5 flashes with a long pause on the last flash, followed by 3 flashes.

  That - what it means, and where can I get a list of all codes error?

  I changed the main battery, changed the spare battery and changed supply - and again, I get the error permanently. I was not able to power the laptop at all since it started. When you press the power button / nothing happens.

  I hope someone on this forum has some information that may help you diagnose this problem. Tech support representatives Toshiba post here?

  Thanks in advance.

  Hello

  I m not a R100 owner but to me it looks like a card mother malfunction because you have already tried to exchange the battery and the AC adapter.

  In this case, the best solution would be if you go to an authorized service provider. Technicians can consult the specifications and they know what means this code I think.
  Here it s only a user to user forum and I have never seen anyone from Toshiba again.

  Anyway, here you can search for the nearest ASP:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported downloads & => find an authorized service provider

  Good luck!

• HP 15-f004dx laptop: power on error code 55133891 for laptop HP 15-f004dx

  power on the 55133891 error code (my power on password forgotten)

  Hello:

  Enter the unlock code...

  40891217

• power on password for hp pavillion g7 error code 62951015

  I have a Hp pavillion g7 I gave to my niece, but she put a power on password on it to keep me and my sister the error code is 62951015 thanks

  Hello:

  Try:

  73639031

• I have a photosmart C7280 printer. Itself under after turning off power and gets the message error/blink

  Photosmart C7200 puts himself after power off the power.  I get an error message and the lights flash.  To clear, I have to disconnect.

  I get various error messages-

  'B8000080, B858BD82, B03Fcc84' I tried all suggestions from HP and nothing elimates the problem web page.  In my view, that it is a common problem with the HP printer.  I want to live with the problem until that matrices of the printer.  I am very disappointed in the way that HP does not support to fix this and future purchases that I turn not to have bought HP products.

• Error code 10 cannot install Maxtor 3200 after power failure

  Original title: maxtor 3200 code 10

  After a power failure cannot not re install Maxtor 3200 get response Code 10

  Hello

  The Code 10 error code is generated when the Device Manager has not enough information or error that spread upwards by device drivers is not recognized by Device Manager. In addition, this error may occur if one of the pilots who needs the unit does not start. If multiple drivers are used by a particular device, it can be difficult to determine which failed.

  I suggest you run the FIXIT from the link below and if it helps. You can also follow the manual steps and check.

  Description of errors related to the 10 Code that generates the Device Manager in Windows on computers

  http://support.Microsoft.com/kb/943104

  Hope this helps and keep us posted.

• Financial reports: Error Code 255 when installing power supply 11.1.2.3.505

  Hello

  I ve tried to install the power supply 11.1.2.3.505 (19795686) for financial reporting.

  The command is:

  C:\Oracle\Middleware\EPMSystem11R1\OPatch > opatch.bat applies C:\Oracle\Middleware\

  EPMSystem11R1\OPatch\19795686-oh C:\Oracle\Middleware jdk - C:\Oracle\Middleware

  \jdk160_35

  But it stops with the following error message:

  OPatch failed to find inventory YES home of the Oracle based. But, location YES

  is provided through "oui_loc" option. Please check the inventory of the Oracle CDM

  e and OPatch execution again.

  OPatch failed with error code = 255

  Any ideas?

  Thank you!

  Hello

  You can download the latest version of OPatch of My Oracle Support (MOS)

  Reference: OPatch - where can I find the latest Version of OPatch? [Video] (Doc ID 224346.1)

  Kind regards

  Harish.

• Cannot change the power state of VM: internal error

  Hello

  I freshly installed OS elementary which is based on Ubuntu.

  VMWare Workstation installation worked fine, but after creating my new virtual machine with a Win 10, the same message comes to me:

  Cannot change the power state of VM: internal error

  I looked a little in the log file, found this dump was set to zero, they changed in etc/security /, but that's all I've managed to find.

  Here is my log file

  Thanks a lot for your help

  PS: I'm leaving a beginner in the Linux world, so explanation would be welcome

  Hello

  Welcome to the VMware community forums.

  I don't think that the problem is related to a beginner linux user, it's a problem triggered by a specific hardware configuration.

  If you look at your log file again, there is an error just before the vmware process attempts to core dump. The dump is a reaction to the problem.

  vmx| E105: PANIC: VERIFY bora/vmcore/vmx/main/timeTracker_user.c:238 bugNr=148722
  

  If you then put the bug number into google, you get:

  http://KB.VMware.com/kb/1227

  Which indicates in return you can set a configuration file to specify the actual frequency of your processor.

  Your processor is an Intel (r) Core i5-3570 CPU @ 3.40 GHz

  The linux variant of the config.ini file they speak on windows hosts is/etc/vmware/config

  --

  Wil

• Moved from VM with Snap Shots, doesn't start: cannot change the power state of VM: internal error

  Hello

  Last week, I decided to move from a Windows host based Linux system. So I went through my VMs their power off and copied to another drive. I then installed 7 Centos and reinstalled VMWare Workstation 12 re-imported the virtual machine in VMWare and I tried to start.

  I received the following message...

  "Cannot change the power state of VM: internal error.

  Suspicious, I looked at the folder that contains the machine virtual and noticed it contained snapshots. DOH!

  I guess it is pretty bad, not sure where to start?

  Any help would be appreciated.

  Thank you

  James

  I copied VM, with and without clichés, without problems. Have a few running on OSX Fusion so

  The first thing I would check would be for folders and .lck files. If so, remove them.

  Lou

• IPMI error code 2900:0221 Power supply failure detected on PE R710

  My VMware ESXi host recently took itself offline. When I was looking for the root cause, I ran a diagnostic test on my R710 EP and the following error is generated:

  Error code: 2900:0221.
  MSG: IPMI - : power supply: sensor power supply (status) failure detected 'PS 2 '.

  The given error code and message can serve as Support to help diagnose the problem.
  Want to continue his tests?

  -end of the error message-

  I saw a post online to update the BIOS and firmware, I did. We are now running BIOS version 6.4.0. I restarted the test with the same results. Any ideas on what I can do to fix this? If the problem is indeed a power supply failure or a sensor on a feed, how do I know which one is bad? Lights on both power supplies are similar to the rear of the server. This unit is no longer under warranty.

  Andoven,

  Error Code: 2900:XXXX is historical, referring to recent system errors. It is usually good to clear the logs of equipment before running the system diagnostics. Included update for your firmware firmware on the power?  I guess that your two power supply status LEDs are both green.  If installed, clear the logs in the OMSA and then reconnect the power supply on the right (2 PSU) and see what OMSA reports.

  Let us know the status of the block of POWER 2 in OMSA and the current version of the firmware.

• Satellite P30-128: installation power management error Code: 0x7E

  Hello, I formatted my laptop yesterday, and I could not install power management software correctly. When the installation is complete, I get "fatal error. Program will be closed. "Code: 0x7E.

  Can someone help me please?

  Hi Simone

  In this forum, you will find many topics on this energy-saving error. Try using the advanced search.
  This product usually mistake it the user does not use the Toshiba Recovery CD but only the original Microsoft OS.
  But according to other topics, there is no explicit solution.
  It is very important that you need to install the drivers of Toshiba in the right order.
  See the installation instructions on the page of the Toshiba driver.