HP 635 Bios message at startup - System Board OOA - Productname & Serialnumber missing

Similar Questions

• product information programmed into the system board are invalid or missing

  the following product information programmed on the system card is missing or invalid

  WHAT information?

  Without providing us with all the details, we can not help you...

• Samsung n130 laptop - not "no operating system" message at startup

  My samsung n130 laptop would not start so I ran the program of recovery solution to address the problem, now since he performed this task, he said: no operating system. Nobody knows what has happened and how to fix it. Thank you

  Hi michaelluke,

  ·         Did you do changes on the computer before the show?

  Follow these methods.

  Method 1: Disconnect all external devices, start the computer and check if the problem persists.

  Method 2: Start your computer in last known good configurations.

  How to start your computer by using last good known Windows XP Configuration

  http://support.Microsoft.com/kb/307852

  Method 3: Follow these steps:

  Step 1: Start the computer in safe mode and check if the problem persists.

  A description of the options to start in Windows XP Mode

  http://support.Microsoft.com/kb/315222

  Step 2: If the problem does not still in safe mode, perform a clean boot to see if there is no conflict of software like clean boot helps you eliminate software conflicts.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Note: After completing the steps in the clean boot troubleshooting, follow the section How to configure Windows to use a Normal startup state of the link to return the computer to a Normal startupmode.

  After the clean boot used to resolve the problem, you can follow these steps to configure Windows XP to start normally.

  (a) click Start, run.

  (b) type msconfigand click OK.

  (c) the System Configuration Utility dialog box appears.

  (d) click the general tab, click Normal startup - load all services and device drivers and then click OK.

  (e) when you are prompted, click on restart to restart the computer.

  Method 4: Follow the steps in the article.

  Advanced Troubleshooting for General startup problems in Windows XP

  http://support.Microsoft.com/kb/308041

  For reference:

  "Operating system not found" or the "Missing operating system" error message when you start your Windows XP-based computer

  http://support.Microsoft.com/kb/321626

  If the problem persists, contact the manufacturer for more help and information.

• Pavilion DV7-6000 series. Error message at startup invalid product information

  I didn't know that my motherboard was bad from the factory.  On the first day, I was unable to do a full factory restore.  I always send to HP.  They sent me a motherboard and after installing it, I was able to do a full factory restore.  It was amazing... However, I now have this error message at startup.  Does that mean exactly?

  When I go into the BIOS, information on the system is xxxxxxx.  When I go to HP technical support.  The product name, serial number and product number is yyyyyyyy.  I know it's fake, why?

  Please don't tell me I have to send it after all.

  

  OK I won't tell you who, but you already know this is bad and you need to call HP. There is a special piece of software used for 'tattoo' Board of Directors. I have seen a few cases where they just give you a link to download and instructions on how make the 'tattoo '.

• System Board pavilion dv7 7099el

  Pavilion dv7 7099el

  Windows 7

  System Board missing info startup error message

  On-board system (00 a) name, number, Configuration, family

  My system borad has been changed and this error on startup rises... There are no other numbers or codes.

  Any help?

  Hello

  You will need to contact one who changed your system board that this information should have been "tattooed" on your replace bios chip.

  Kind regards

  DP - K

• I get the message at startup

  I get the startup message that I got my motherboard replacement for my laptop since 2 months ago

  product is HP Pavilion

  Model DV3-2360ee

  warranty: 1y1y0y

  series: CND0012NVV

  Model: DV3-2360-ee

  jump your assistant with my this message, it's making me delay when openning this pc

  I get what exactly the message

  product information is invalid

  the following products information programmed into the system card is missing or invalid

  Serial number of product System board (00 a)

  Product number for the Board of Directors (00 a) system

  I'm finding your quick helpness

  Thanls

• Compaq Presario 6604AU-BIOS and other startup problems

  My laptop Compaq Presario 6604 to THE beginning to give a lot of problems in recent times. Every day, I spend a lot time on their fixation; no resolution anyway.

  Problem 1: BIOS hangs at startup

  Problem 2: If the MESSAGE is finished, Windows crashes at startup (Vista blocking at the mobile bar)

  Problem 3: for the last three days, CD/DVD-ROM does not.

  System configuration: CPU AMD Athlon X 2, 2 GB DDR 2 RAM (2 x 1 GB module). nForce Chipset MoBo, GoMobile GeForce 7150 Graphics Card 160 GB HDD. Windows Vista Home Basic (32 bit)

  Problem 1:

  BIOS hangs at the initial screen for 3-5 minutes. After 3-5 minutes, it goes to the next screen. Pressing only works key "ESC". I tried the BIOS flashed with the latest firmware (PRICE Phoenix F 32). Problem persists.

  What I tried:

  1 memory module checked. Tried different RAM module.

  2 checked hard drive for errors - Self Test passed.

  3 flashed the BIOS with the latest Firmware.

  Problem 2:

  Vista hangs at the initial screen (screen bar trip)

  What I tried:

  1. Startup Repair

  2. removed PCMCIA, 1394 driver files.

  3. system restore

  4 re-installled Vista.

  It's really frustrating to see the screen hanging even after reinstalling Vista. The Startup Repair tool produces the following result:

  Signature of the problem:
  Problem event name: StartupRepairV2
  Signature of the problem 01: AutoFailover
  Signature of the problem 02: 6.0.6000.16386.6.0.6000.16386
  Signature problem 03:2
  Signature of the 04:65537 problem
  Signature of the problem 05: unknown
  Signature of the 06 problem: NoRootCause
  Signature of the problem 07:0
  Signature problem 08:2
  Signature of the problem 09: WrpRepair
  Issue 10:2 signature
  OS version: 6.0.6000.2.0.0.256.1
  Locale ID: 1033

  Problem 3:

  If CD/DVD disc problem is related to the two above, we can discuss it further. Otherwise, I'll look it up in other sections of the forum.

  Any help would be appreciated. Thanks in advance

  Solved!

  The problem was with supply management power to the motherboard. I took it to a service person and he said it's a common problem with Compaq V6000 laptop /V3000 of the series... He solved the problem in 30 mins by replacing the chips... Too bad I spent several weeks on troubleshooting the problem myself.

  I hope that this post will help someone...

  Thank you!

• HP Deskjet 3520: Error Message at startup

  I now have a 3520 printer that I have had for 2 years. Previously, I had a model 5510 and uninstalled all programs to change information.

  In the last 2 months, I get this message at startup upward.  Run the specific DLL module is not found.  C:\Programsfiles\HP\HPPhotosmart 5510d sries\bin\HPstatus BL.dii.

  I am able to click and lose, but I don't know that it slows down the startup

  Any suggestions please

  The Board of directors who best matches is Desk top. Drop-down menu would not allow this selection. Laptop is incorrect

  I followed your instructions but it made no difference.

  I went back to the list and not the 3 elements that says no 'found', and this has solved the problem.

  I do not how to send you a link to see

  Thank you very much

• Invalid Boot.INI message at startup

  After changing the battery CMOS, I get an invalid "boot.ini" message at startup.  Any suggestions?

  It is not sensible that results change the CMOS tossed in this message, but you can understand the problem and fix it.

  In a single partition configuration, XP doesn't have even a boot.ini file to start.  If missing the file XP will complain but always starts very well without one.

  If you see a message like this:

  Invalid BOOT. INI file
  Booting from C:\windows\

  This means generally that the c:\boot.ini file can be completely absent (for some reason any).

  Miss the file would require a little extra work, since it is normally a hidden system, read-only file, but I can think of many things that is happy to remove it for you.

  If the system is working properly, what do you think happened to the system since the last time, he did not work properly?

  You now, or have you had the "Ask Toolbar" installed on your system?

  You have now or have you ever used third-party applications on your system where the product description includes descriptive as sentences:

  cleaner, mechanic, detective, doctor, heal, optimize, Inspector, clean, tune up, speed up, fix up, compact, compress, faster, power, boost, boost, gum, muncher. one click fix, new, intuitive, errors, stop crashes, stop errors, improves, allows you to save money, risk free, guaranteed or any third-party program that has an icon that looks like a gear, pinion, belt holder, key, key, screwdriver or plunging arrows?

  After the contents of your boot.ini file so that we can see it and help fix you that.  If the file is missing, you can create a new one.

  Here's how:

  From your desktop, right-click my computer, choose Properties, and in the startup and Recovery Section, click settings.

  Starting the system section, click on Edit and who will open Notepad on your boot.ini file.

  Type Ctrl + A to select/highlight all the text, type Ctrl + C to copy the selected text in the Windows Clipboard, then in your next reply here, type Ctrl + V to paste the text from the Clipboard into your next reply.

  What you paste into your next reply might look like this:

  [boot loader]
  timeout = 30
  default = multi (0) disk (0) rdisk (0) partition (1) \WINDOWS
  [operating systems]
  "multi (0) disk (0) rdisk (0) partition (1) \WINDOWS="Microsoft Windows XP Professional "/ noexecute = optin/fastdetect

  Click the red X to close Notepad, etc.  When you are finished.

  Here's another thread, you can watch where another user had a similar problem which was resolved (ignore all committed useless Microsoft Support Engineer responds 'expert'):

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_xp-performance/Windows-XP-Home-Edition-SP3-i-cannot-create-a/00c97a2e-79cf-44BF-94ed-d06e8a582903

• I get error message at startup lift that C:\WINDOWS\emelumihudusi.dll is not found. Impossible to find info on this program, he worked with.

  I searched for information on this error and can't find anything except 'pay' for programs that corrects errors of .dll.  I'm not having problems I can see with one of my installed programs.

  If you don't want to waste your time, I wouldn't do it.

  I'd do things like:

  It is sometimes easy to get rid of the error message by doing something like disable the startup item in msconfig (if you can still find), but I suggest you fix the problem and difficulty not only the symptom of the problem by simply deleting the startup message.

  I would also not recommend you start digging in the registry to try to find the startup item and remove it unless you have a backup of your system or at least a backup of your registry, because there is no 'Cancel' or 'quit without saving changes' option in regedit.  If you make a mistake, that's all.

  These ideas relieve 'rapid' and sometimes risky of the symptom if they not even work at all, but they can't actually solve the problem.  Also, I'd be suspicious of ideas that begin with the words "try."  You don't need to try things, you need to fix things.  You don't need to try ideas that might work, you must do something that will always work all the time.

  Here are the detailed instructions that protect you and solve your problem in the 'right' way.

  There is very little. DLL files that should be loaded from the C:\WINDOWS folder and is not one of them.  If you do not have a good explanation for the name of the file in a Google search, the chances are good that your system is currently or has been infected by malware.
  A "Cannot find...". ', ' Failed to start..., "Could not load..." ». "Might not work... "" Cannot run ""error loading... ". "or"specific module could not be found"message at startup is usually related to the malware that has been configured to run at startup, but the referenced file has been removed after a malware scan, leaving behind him a startup item or the registry entry pointing to a file that does not exist.
  It might be a removal of malicious software or an application not installed.  The entry may have a curious looking name since it was probably generated at random when the malware was installed. If you search your system for the referenced file, you may not find.
  Windows attempts to load this file but cannot locate because the file has been deleted for most probably during an analysis of the malware. However, an orphaned associate of remainders of startup parameter or registry entry and tells Windows to load the file when you start or connection.
  So you should delete the referenced entry Windows stop trying to load or run the file. It may or may not be included in the registry, but you can find it.  Autoruns (see below) you get the elements no matter where it is.

  You must be sure to solve the problem and not just fix the symptom of the problem by simply relieving your message - system is not a fix (there is a difference).

  If you just locate and uncheck the item in msconfig, which disables the element but does not remove the reference to the element of false starting your computer.   The msconfig program is not a Startup Manager, that's a troubleshooting tool.  Disabling things in msconfig to put an end to the messages and think that your problem is solved is short-sighted and leave behind him a sloppy XP configuration.  Just disable the display of a start-up error message should not count as a 'solution' to the problem.
  If you are comfortable editing the registry, you can find and remove the reference directly from there or remove it using a popular third-party tool called Autoruns.  The problem can always be found in the registry well.
  Before making any changes to your registry by hand or with third-party tools, don't forget to first make a backup of the registry
  . There is no cancellation or exit without saving the option in regedit.
  Here is a link to a popular registry backup tool:
  http://www.SnapFiles.com/get/ERUNT.html
  You can also use the Autoruns to find the element of start remains little matter where he's hiding.  Autoruns does not install anything on your computer.  It will display all startup locations where the reference may be then you can turn it off or remove it completely.  Here is the download link for Autoruns:
  http://TechNet.Microsoft.com/en-us/sysinternals/bb963902.aspx
  Run Autoruns.exe and wait that he at the end of the filling of the list of entries.
  When the Autoruns is finished scanning your system, it will say "Ready" in the lower left corner.  Autoruns can be a little intimidating to first if you have never seen it before because it displays a lot of information.  You are really interested only a few sections.
  The problem is usually to start the system or the user startup entries, then click the connection tab and see if the startup item is there.
  Scroll through the list and look for a boot entry associated files in the error message.
  If you can't find on the connection tab, look in any tab.
  You can also click file, search to search for logon, or any tab for all or part of the name of the element.
  Right-click on the offending entry and choose Remove.  If you are not sure what it is, you can just turn it off, restart and if the problem is resolved and things are functioning normally and everything works fine, then remove the offending entry.  If you don't see it in Autoruns, you may edit the registry and remove the item from your startup folder it.  Autoruns shall display the same information however.
  Given that your system has or has had an infection, follow up with this:
  Perform scans for malware, and then fix any problems:
  
  No matter what you use for malware protection, follow these steps:

  Download, install, update and do a full scan with these free malware detection programs at:
  Malwarebytes (MMFA): http://malwarebytes.org/
  SUPERAntiSpyware: (SAS): http://www.superantispyware.com/
  They can be uninstalled later if you wish.
  Restart your computer and solve the outstanding issues.

• I get the error message at startup missing modul c:\windows\system32\wabqwuny.dll

  what I'm doing. Download this file are what

  It is sometimes easy to get rid of the error message by doing something like disable the startup item in msconfig (if you can still find), but I suggest you fix the problem and difficulty not only the symptom of the problem by simply deleting the startup message.

  I would also not recommend you start digging in the registry to try to find the startup item and remove it unless you have a backup of your system or at least a backup of your registry, because there is no 'Cancel' or 'quit without saving changes' option in regedit.  If you make a mistake, that's all.

  These ideas relieve 'rapid' and sometimes risky of the symptom if they not even work at all, but they can't actually solve the problem.  Also, I'd be suspicious of ideas that begin with the words "try."  You don't need to try things, you need to fix things.  You don't need to try ideas that might work, you must do something that will always work all the time.

  Here are the detailed instructions that protect you and solve your problem in the 'right' way.

  If you do not have a good explanation for the name of the file in a Google search, the chances are good that your system is currently or has been infected by malware.
  A "Cannot find...". ', ' Failed to start..., "Could not load..." ». "Might not work... "" Cannot run ""error loading... ". "or"specific module could not be found"message at startup is usually related to the malware that has been configured to run at startup, but the referenced file has been removed after a malware scan, leaving behind him a startup item or the registry entry pointing to a file that does not exist.
  It might be a removal of malicious software or an application not installed.  The entry may have a curious looking name since it was probably generated at random when the malware was installed. If you search your system for the referenced file, you may not find.
  Windows attempts to load this file but cannot locate because the file has been deleted for most probably during an analysis of the malware. However, an orphaned associate of remainders of startup parameter or registry entry and tells Windows to load the file when you start or connection.
  So you should delete the referenced entry Windows stop trying to load or run the file. It may or may not be included in the registry, but you can find it.  Autoruns (see below) you get the elements no matter where it is.

  You must be sure to solve the problem and not just fix the symptom of the problem by simply relieving your message - system is not a fix (there is a difference).

  If you just locate and uncheck the item in msconfig, which disables the element but does not remove the reference to the element of false starting your computer.   The msconfig program is not a Startup Manager, that's a troubleshooting tool.  Disabling things in msconfig to put an end to the messages and think that your problem is solved is short-sighted and leave behind him a sloppy XP configuration.  Just disable the display of a start-up error message should not count as a 'solution' to the problem.
  If you are comfortable editing the registry, you can find and remove the reference directly from there or remove it using a popular third-party tool called Autoruns.  The problem can always be found in the registry well.
  Before making any changes to your registry by hand or with third-party tools, don't forget to first make a backup of the registry
  . There is no cancellation or exit without saving the option in regedit.
  Here is a link to a popular registry backup tool:
  http://www.SnapFiles.com/get/ERUNT.html
  You can also use the Autoruns to find the element of start remains little matter where he's hiding.  Autoruns does not install anything on your computer.  It will display all startup locations where the reference may be then you can turn it off or remove it completely.  Here is the download link for Autoruns:
  http://TechNet.Microsoft.com/en-us/sysinternals/bb963902.aspx
  Run Autoruns.exe and wait that he at the end of the filling of the list of entries.
  When the Autoruns is finished scanning your system, it will say "Ready" in the lower left corner.  Autoruns can be a little intimidating to first if you have never seen it before because it displays a lot of information.  You are really interested only a few sections.
  The problem is usually to start the system or the user startup entries, then click the connection tab and see if the startup item is there.
  Scroll through the list and look for a boot entry associated files in the error message.
  If you can't find on the connection tab, look in any tab.
  You can also click file, search to search for logon, or any tab for all or part of the name of the element.
  Right-click on the offending entry and choose Remove.  If you are not sure what it is, you can simply disable, restart and if the problem is resolved and then remove the offending entry.  If you don't see it in Autoruns, you may edit the registry and remove the item from your startup folder it.  Autoruns shall display the same information however.
  Given that your system has or has had an infection, follow up with this:
  Perform scans for malware, and then fix any problems:
  Download, install, update and do a full scan with these free malware detection programs:
  Malwarebytes (MMFA): http://malwarebytes.org/
  SUPERAntiSpyware: (SAS): http://www.superantispyware.com/
  They can be uninstalled later if you wish.
  Restart your computer and solve the outstanding issues.

• ESX04i on HP DL385 G2 sensor error: System Board 2 ProcHot - limit exceeded

  Hello everyone,

  I installed a server esxi to a hp dl385g2 (8.50 firmware). After the first start, a sensor after the following error message:

  System Board 2 ProcHot - limit exceeded?  ?:|

  can someone tell me what kind of error this is?

  THX

  Mike

  Just download a previous HP firmware CD

• Check for new messages at startup does not work in the first period of 10 minutes after v38 updated. Work at the end of 10 minutes. CAUSE unknown - went away after reinstall

  After the 38.0.1 of 31 thunderbird update does not check for messages at startup, tried on two workstations, mail for a single account on each account, one was pop and other imap. The check box in the accounts-> server settings has no effect. Or not safe mode or the option advanced messages "include this server when getting new messages". "." Activity Manager shows not even he is trying to connect. The question mark function still works well so if I wait 10 minutes he gets messages automatically...

  said rafikiphoto

  I reinstalled the program once more and it works OK but it's already happened and it fails once more.

  The last installation permanently solve this (so far)?

• When I send a message to blueyonder system says the message was sent, but the recipient can't find it in emails or on the server.

  I create a message and press send. The system indicates that it connection, then the message has been sent. When the recipient checks the message on its system and/or the server, it can not find the message. I sent him direct messages from my server and Outlook Express and it does not get them only when you use Thunderbird messages go missing. I have to use special settings to send messages to Blueyonder?

  I suggest that contact your email provider. Similar problems have been reported of users blank.

  http://community.virginmedia.com/T5/other-queries/emails-to-blueyonder-users-not-being-received/TD-p/1813248

• Re: Need to motherboard / system board for Qosmio G20 106

  I would be grateful if anyone can help me find one.
  My laptop is dead now and need a mother replacement on board.

  Please also provide you with the best suggestions to find the online store for the system board. I searched for the part, but unable to find it.
  Thanks in advance.

  PS Many people have serious problems with this type of model, mainly with the cooling system! It's my first pc/laptop and I want it to work again!
  Motherboard: fnn 2 s 1 a5a001404010

  Hello

  All parts can be ordered from local Toshiba ASP.
  Contact Toshiba service provider in your country and order this compatible part.

  But note; It s not cheap part! The replacement of the motherboard is still an expensive procedure