HP Compaq desktop and dell monitor analog compatibility

Similar Questions

• Samsung and Dell monitor questions

  Hello:
  I had a given PC new and works fine, but when I hooked up with monitor with Samsung, a floating message popping up in the middle of the screen... "Not optimum mode, recommended 1280 x 1024 60 Hz Mode" and the screen empties a few minutes later. When I tested with another monitor with Dell, there are no floating message and gets a good quality screen that shows the Dell monitor is compatible not compatible Samsung to PC refurbished.

  Monitor Samsung was hooked with two different PC KVM switch, and no problem with them.

  Is there a way for me to do the given PC replacement compatible with monitors, "Dell" and "Samsung"?

  Thanks for any help in advance.

  "" floating"message popping up in the middle of the screen"

  "Not optimum mode, recommended 1280 x 1024 60 Hz Mode '"

  Your Samsung monitor is a type of format of 4:3 image, that's why she asked '1280 x 1024 60 Hz '.

  Your video card is NOT defined for it. How to change the settings:

  http://www.SevenForums.com/tutorials/256-screen-refresh-rate-display-settings.html

  See above with the Dell connected monitor. Set it to 1280 x 1024 at 60 Hz, and then connect the Samsung monitor and see what happens...

  Type of form factor small PC are not the easiest machines to be upgraded, especially regarding video cards. I wouldn't go this way if I were you...

• Black glitter and LED monitor S2440L screen

  I have a new LED monitor from Dell which flickers to a black screen during market for a few seconds and then turns back on. I can't understand why this happens. It happened when my monitor has been connected to the slot built in HDMI on my motherboard. And it always happens when I connect the monitor to the HDMI slot on my new NVIDIA GeForce GT 630 of ASUS graphics card that I bought recently. My motherboard is the ASUS P8Z68 - VLX running Windows 7 with an Intel i5 processor. DELL LED monitor is S2440L. Anyone experience this state of the black screen that comes at random on the time where to watch movies or even surf the net.

  Hello

  I have the same problem as you with my L-2440. The screen flickers and sometimes it's curtains blackout for a few seconds. I think this problem for this monitor is not an isolated case, because many people complained the same problem.

  I have noticed before I installed driver Dell and Dell monitors management program, this problem does not exist. Admittedly, I don't use 1 hour after the introduction if theres no way to be sure about that. Anyway I uninstalled both and use the driver default Windows (generic PnP monitor) and disable DDC/DCI under 'Other settings' in the configuration, monitor and now dancing lines are for the most part disappeared (sometimes but rarely sound still there), but black still happen.

  After experience, it turns out that it is related to electrical installation of the dwelling. Whenever someone support some switch in my house (On or Off), the screen will be black without fault. Im sure this model in particular have some bad Earth or something since I have never experience such problem in previous Dell monitor that I own or any other device. Try it yourself and make people put the switch in your home.

  I am awaiting response to Dell too because it is the time of 2md my monitor is replaced (totally busted S2320L and cannot be turned on) and Dell replaced by 2440L as the third replacement. Anyway Im afraid it will break the monitor sooner or later and I'm inclined to return it...

• HP Compaq and Dell Analog monitor compatible?

  I wanted to add that I also tried to pass the power to the monitor, computer cords and also VGA cables and nothing has helped so far.  I always get the saving mode on my Dell e193fp analog monitor.  My Hp compaq 5750 is loading windows xp, and I hear music... just no activity of the screen except "power saving mode hit any key or move the mouse.  Two of these units have not been used in a while, the office and the monitor have been inactive for more than 6 months.  If I disconnect the vga monitor, the power button cable transforms whenm amber green verses he is hung up to the red, white, gree, box blue 'self test' floats on the monitor.  I am unable to get one of the buttons before you take me to a menu on the monitor or the other.

  lalea878 wrote:
  

  I have it connect to the VGA port on the back of the HP compaq dc5750 Small Form Factor desktop computer... 15-pin.  The dell monitor has only a port... No. vga other ports except for power on the dell monitor.  HP compaq SN # {removed privacy}.  I've never hung a monitor up to a video card and didn't know that I could plug the monitor directly into the card?  I know not where the map is I have opened the HP and do not see it, but am not familiar with it.  This unit has a video card?  If so, how can I connect Dell e193fp monitor without using the VGA port?  Maybe the VGA port is disabled because my acer does not work on this HP compaq but works on my other HP compaq dc5750 SN #{removed privacy} / windows 7.

  THX

  Laura

  Connection cable vga card screen depends on whther or not your PC is configured with a video card. It is not necessary to open the PC. Just look at the back of the PC. If there is a card, it will be in one of the slots instead of the bottom basket I/O headers (as in the picture in my previous post).

  Test the display on another PC or laptop to test the display and cable. This is the method of troubleshoting simpleest. If it doesn't, then the problem is with the display or vga cable.

• U2415, around the gap between the Windows desktop and the edge of the monitor (bezel)

  Hello

  I have a Dell Ultrasharp U2415. I've read all the FAQS and I know I have to perform the SUBMISSION, but before doing so, I just want to know if it is normal to have a gap between the Windows desktop and the edge of the screen. If the Windows desktop is not covering or fill the entire screen. There all around the smaller than a 1/4 "gap between the edge of the windows desktop on the edge of the bezel of the monitor, and this model has almost no bezel. The graphics settings in Windows 10 are set to use the native resolution of 1920 x 1200 monitor. I tried with different computers (all windows 10), and the drivers are up to date. The monitor is connected via HDMI since I don't have portable computers not with DP interfaces. Laptop computers have Intel and ATI video cards. I have check the put option to scale on the video card software and it is set to 100%. So, is this gap normal? Is the edge Office Windows 10 supposed to touch the physical edge of monitors?  If the gap is not normal, I will perform the integrated test.

  TIA!

  Based on the YouTube comments, which seems to be normal. "But you must run the APPLICATION to see if the"smaller than 1/4"gap" appears. If Yes, then we can say that it is normal. If this is not the case, then some settings of the operating system is the culprit.

• border of 1 inch on my gateway DX4300 desktop and I cannot get rid of it. I have a Dell ST2310 HDMI

  border of 1 inch on my gateway DX4300 desktop and I cannot get rid of it. I have a Dell ST2310 HDMI. I tried the ATI driver to this day and used the upscaling up to 0. Once the screen saver comes on he returned to the border of 1 inch on my destop and reduced my Explorer window to fit on the border. When restart my computer I can't see the commissioning or put my PC in safe mode. I need help.

  Hello

  Try to update the graphics card drivers for the monitor to which you connect to the laptop using HDMI. Visit the manufacturer's Web site to do the same.

  Update drivers: recommended links

  http://Windows.Microsoft.com/en-us/Windows7/update-drivers-recommended-links

• I have installed the latest updates for my Compaq desktop computer and the DVD/CD drive bay door will not work.

  I have installed the latest updates for my Compaq desktop computer and the DVD/CD drive bay door will not work. I can get the led light will stop flashing when I open the door all the way, the machine detects the drive but do not read or close on its own, how can I get this disc surgery? Downloading updates, I installed a software disc, when I ejected the disc, the drive comes of is stopped. The computer still sees the drive, but will not read or even close on its own. I also had been using my computer in mode mute until I tried to increase the volume and now the computer tells me no playback device installed. Device Manager acknowledges the Harmon/Kardon soundsticks connected to it, but nothing does, how it works? The Control Panel also sees the soundsticks, but still when I try to move the volume the computer says there is no playback device installed.

  Hello

  1. do you get any error code or error message?

  2. what day you installed recently?

  It seems to be a problem with the hardware. I suggest you try to uninstall and reinstall the CD/DVD driver and check if it helps.

  Follow the steps to uninstall and re-install the drivers.

  a. click on start toreduce this includes this im and then click Control Panel.

  b. click system and Maintenance, click Systemand then click on Device Manager.
  Note If Control Panel is in Classic view, double-click System, and then click Device Manager.

  Reduce this includes this imageIf you are prompted for an administrator password or a confirmation, type the password, or click allow.

  c. in the Manager device, expand CD-ROM/DVD-ROM drives, right click on CD and DVD devices and then click Uninstall.

  d. When you are prompted to confirm that you want to remove the device, click OK.

  e. restart the computer.

  If the methods mentioned above did not help, then it would be best to contact the manufacturer of the computer/CD/DVD player.

  Hope the information is useful.

• Video card GeForce GTX645 and two monitors Dell

  Just place an order for a Dell XPS PC 8700 with a GeForce GTX645 video card. I'm trying to figure out how I'll be able to connect my two Dell monitors to the video card. My monitors are a Dell 2407WFP-HC 24 '' and a Dell IN2020M 20 ". I'm fairly certain that the 24 "monitor has a DVI - D connector, and I think (but I'm not sure) the 20" monitor also has DVI - D.

  It appears by looking at the specs for the GeForce GTX645 there a port DVI - D and DVI - I port. If this is the case, how can I connect two monitors using DVI - D video card?

  -Larry

  Yo is not an adapter to hook up 2 monitor DVI - D DVI - I and DVI - D + HDMI + [...] video card.

  DVI - I mean it is a compatible port DVI - D AND you could plug an adapter DVI / VGA for use an old monitor (VGA d - Sub 15 pin)
  http://en.Wikipedia.org/wiki/Digital_Visual_Interface
  +
  

  DVI - I simply means that the DVI connector has some extra pins (on the right, under the direction, my mistake) with the data (if necessary)

• On my Dell monitor color is gray when viewing photos.

  Colors on my Dell monitor

  Hello

  I hope you can help!  I have a Dell monitor and a computer HP, for a reason that I can't get the colors on my screen.  (Works of color before entering the internet then my screen saver is ok but all my all my pictures are grey!)
  im not very computer therefore answers in plain English please! Thanks, Jules

  Hi Julie,.

  1. is the issue limited to the pictures on your computer?

  2. make the computer desktop and other screens come well?

  3. what program do you use to see the pictures?

  4 did you changes in the program before the show?

  If the question is limited to viewing photos, you can use a different program for the same thing and see if the problem persists. You can use Windows Live Photo Gallery.

  Windows Live Photo Gallery for Windows XP

  Respond with more information so that we can help you best.

• S2440L 24 '' Dell monitor

  Hello

  I recently bought the S2440L Dell 24 "monitor and the text looks awful.  The text is thin and pixelated.  It is the worst-looking text I've seen on a screen in recent years.

  I am wpmdering how I should adjust the monitor settings to improve the display of the text?

  Thank you

  Hi jediem,

  You can run a self-test by following the steps below and see if there is a problem with the monitor:

  • Turning off the computer and the monitor.
  • Unplug the video cable from the back of the computer. In order to ensure the proper functioning of the Self Test, remove the analog (blue connector) cable to the back of the computer.
  • Turn on the monitor.
  • The floating dialog box should appear on-screen (against a black background) if the monitor cannot detect a video signal and is working correctly. In self-test mode, the power led remains white. In addition, depending on the selected entry, the following dialog box scrolls continuously through the screen.

  

  • This box appears during normal operation if the video cable is disconnected or damaged.
  • Turn off the monitor and reconnect the video cable; then turn on the computer and the monitor.

  If the monitor screen remains blank after that customers use the previous procedure, check the video controller and the computer, because the monitor is operating properly.

  You can also perform a monitor factory reset and see if it helps:

  1. Press any key to launch the OSD menu and press on to display the main menu.
  2. Press up and down keys to switch between the options in the Menu. When you move one icon to another, the name of the option is highlighted.
  3. Go to "other settings".
  4. Select 'Factory reset '.
  5. Check if it works.

  Please share the findings.

• HP Compaq 8710w and drivers Windows 8.1 for Quadro FX 3600 M

  Hi everyone I have a HP Compaq 8710w and it works very well so far.

  There is a problem experienced with Quadro FX 3600 M drivers in Windows 7 If you do not use the old drivers given the HP (186,24) but other than that, everything is ok.

  https://forums.GeForce.com/default/topic/516145/legacy/Quadro-FX-3600m-problems/

  / t5/Notebook-HP-ProBook-ZBook/8710w-Win7-random-freezing-black-screens/td-p/2337373#. VFdIW_msWfw

  I want to improve my current Windows 7 Ultimate for Windows 8.1 but I can't find the official drivers from HP and I'm afraid that the blue screens of death will be back.

  Is it possible to give official drivers for the Quadro FX 3600 M of this laptop great for Windows 8.1 because it is a known problem that all the other drivers do not work properly.

  Thanks in advance

  George

  P.S. This thread was moved from the company - Compaq, Elite, Pro for laptop - PC HP ProBook, EliteBook, ZBook, slate/Tablet PC, Armada, Compaq LTE. -HP moderator of the Forum

  As for the help of all the other drivers, there is an option that works for me.  If you must use a driver newest to work with Win8.1 (I have) there is a solution, but the will of costs over the life of the battery!

  I had been using latest drivers for my 8710w fx3600m rigging using this method and I hope that it is a possible solution for you as well:

  Download a newer driver for the fx3600m for Win8.1 and it's a good idea to film for WHQL drivers.

  I am currently using the 334.95 driver (334.95-quadro-notebook-win8-win7-64bit-international-whql.exe).

  DO NOT install the drivers right away.

  Download"Powermizer Switch.exe" here - http://www.box.net/shared/v7jpoateoq

  Powermizer Switch.exe extract on your desktop for quick access.  You will need to be easily accessible.

  It may be a good idea to make sure you're clean of any other video drivers Nvidia beforehand.

  Now, we are ready to install the driver.

  IMPORTANT!  When you install the driver, only select the driver and nothing else and don't forget to restart immediately!

  Once on the Windows desktop, start immediately 'Powermizer Switch.exe', click on 'Powermizer Off' and YES to restart!

  This will allow all pilots before the xx 192.le and eliminate the blackscreen/blue screen issue.

  NOTE: any time you pass or update the drivers (former 192.xx), you will need to use this scheme every time!

• X 230, Intel HD 4000, dock and three monitors, how?

  Hello

  I just got new X 230 (makes 12/12). It has intel HD 4000 and processor i7-3xxx-series.

  I also got dock (the usb3 support).

  I have foud some topics saying that x 230 would support 3 monitors, but how?

  I have 3 x full HD monitors, 2 of them is connected with other with VGA and DVI to dock to dock.

  Windows screen settings allows me to activate the 3 monitos, but custom 3rd "wake up" and after that windows manager reopenin of screen it says that 3rd monitor is "disconnected". The Intel tool provides only option for 2 monitors.

  So, it is possible to activate the 3rd monitor?

  Hey there styleza,

  Thanks for clarifying the dock you are using by comparing what you found there to the PSRef for your machine, it doesn't seem to be the case. The PSRef States:

  "Intel HD Graphics 4000 in processor, supports external analog monitor via VGA and digital monitor via Mini Display Port; supports two independent screens. "Research on all for X 230 PSRef sheets, I agree, it doesn't seem Optimus technology was available for this machine as all PSRef sheets I could find for X 230 different configurations list only the Intel HD Graphics 4000. Sorry to be the bearer of bad news.

  At the very least, I hope this clarifies things for you.

• Cannot get the resolution max X 1 carbon (3443CTO) and Dell U2713HM

  I recently bought this dell monitor and trying to connect via a mini displayport to DVI Dual link adapter to a Dual Link DVI cable to the monitor.

  Can't see an option to increase the resolution after 1080 p.

  Have updated the dispay driver 4000 Intel and install the U2713HM driver.

  Does the x 1 carbon (3443CTO) support 1440 p?

  Just use a miniDP to DP cable. I use this with mine first generation X carbon 1 and U2713hm and it can support this resolution very well.

• Can I connect my printer on both a desktop and a laptop wireless?

  I have my Photsmartf HP Premium printer connected to my Compaq desktop computer via a USB connection.   Also, I have a HP laptop with wireless and wonder if I can hang it up to the printer using the wireless connection?  Can I use the two types of connectivity with the same printer?

  OK, at the front of the printer: Setup > network > Wireless Setup Wizard.  Run the wizard to connect the printer to the network.

  Then, delete all instances of the printer on your PC (start > Control Panel > printers).  Then, add the printer in this way:

  1. make sure the printer is on and connected to your network. Verify that you can access the printer's internal web page by accessing its IP address before continuing.
  2. click on > start > Control Panel > printers.
  3. click on add a printer
  4. Select local printer
  5. Select create a new port and select Standard TCP/IP Port, and click Next.
  6. under device type, select TCP/IP Device. Under the name of host or IP address, enter the IP address of the printer. Click Next.
  7. Select Hewlett-Packard in the list of manufacturers and select and select your printer model. Click Next.
  If your printer model is not in the list, then select disk provided, browse the CD that came with your HP printer and select the first file begins with hp and ending with INF. click Open, then OK. Select your printer model. Click Next.
  8. If prompted, use the driver that is currently installed.
  9. He will ask the name of the printer - enter a new name or use the one existing. This will be the name of the printer that you select from other applications.
  10. we may ask you to share the printer. Choose No.
  11. the printing area of Test Page is displayed. Go ahead and print it out.
  12. click on finish.

• I recently formatted my old hp laptop compaq nc6000. and I try to install a new system of operation

  I recently formatted my old hp laptop compaq nc6000. and I try to install a new operating system windows 7. the problem is that you cannot boot from the cd it shows BOOTMGR is missing press alt + ctrl + del to restart or when it starts, it displays the press any key to boot from the overflow of memory cd THAT BOOTMGR is missing, press alt + ctrl + del to restart. What can I do I really want to use it as soon

  its not authentic I have it burned the ISO download?