HP G6: Problems of combustion

Similar Questions

• Satellite A80-129: Mat * a DVD - RAM UJ-830 s cannot burn DVDs

  MODEL: SA80-129
  DVD RAM TYPE MAST * A DVD-RAM UJ-830 S
  SYSTEM: WINXP
  SOFTWARE: NERO

  (1) DVDRAM CAN READ CD AND DVD EASILY, IT Burns CD WELL, BUT cannot burn DVDs, IT SHOWS: G:\ IS NOT ACCESSIBLE INCORRECT FUNCTION, UNTIL IT WORKS WELL. the blank dvd is not a problem, before I used even type a blank dvd to burn.
  (2) even allow the recoding in the properties, the properties shows the Virgin dvd 0bytes.

  all PROMTLY ANSWER would BE MUCH APPRECIATED.

  It doesn't sound good.
  I had a similar problem of combustion and the end of the story, I replaced the drive ;(
  However, try to remove the drive from Device Manager, and then again to restart the operating system should recognize the device again.
  Then you could check if it able to burn the DVD s s.
  I think you should also try burning different DVD media.

  I have visited many work sites and the reader, and especially the calibration lens malfunction could be responsible for burning problems.
  This could be a worst case and in this case, the replacement is necessary.

• Satellite A40-231: cannot burn CDs or DVDs

  Hello

  I can play CDs without problem, but I can't write them and DVD. I tried with Windows XP default recorder (by Roxio as he said), Nero and Infra Recorder but still had the same problem. Combustion process begins and finishes without errors with all of this software, but when I check the contents of the CD later, I see that nothing is written there, the CD is just considered as empty, or sometimes seen with 0 MB of available space, 0 MB total space.

  I tried with the CD - r, CD - RW and the DVD but I got the same problem. I have 2 389 MB free in my disk space hard as he is seen by Nero for the ability of the temporary folder that it uses.

  My DVD-R /-RW is recognized by Windows XP without problem and also, I installed the latest firmware from the site Web of Toshiba.

  Here are my specifications:

  Toshiba Satellite A40-231
  Toshiba DVD - ROM SD-R6112 DVD-R /-RW DRIVE Firmware Version: 1333 (latest news on the site Web of Toshiba Driver)
  System dual boot: Windows XP SP2 and Linux Debian Sarge

  Hello

  In the manual of Toshiba, you compatible o is a list and supported the CDs and DVDs.
  You must use these mediums as they are tested and should work correctly.

  Another tip:
  Go to start > run > and start recording with a command regedit

  Delete values
  upperFilter and UpperFilter of this key:
  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Contro l\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  I've done on my laptop and noticed some improvements

• WMP says new CD - R disc is "filled".

  Hello.  I have a Sony Vaio with Windows 7 Professional laptop VPCF121GX.  When I insert a new CD - R disc to burn in Media Player, it says that the disk is 'filled '.  I checked online the new driver updates, but apparently it is updated.

  Recently, I also noticed that I have problems of combustion of other types of files to a CD without using WMP.
  Any help would be greatly appreciated!
  Omar

  Hello.  I have a Sony Vaio with Windows 7 Professional laptop VPCF121GX.  When I insert a new CD - R disc to burn in Media Player, it says that the disk is 'filled '.  I checked online the new driver updates, but apparently it is updated.

  Recently, I also noticed that I have problems of combustion of other types of files to a CD without using WMP.

  Any help would be greatly appreciated!

  Omar

  In the start search box type > regedit

  Now, look for the following: -.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Contro l\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318
  Remove the filters above and below, restart the computer.

• Having a problem with loading in the combustion chamber

  Hello

  I'm having a small problem I could use help with. I'm not really sure what's going on, but I'm having a problem with one of the pages of my site does not when you try to view the page in Firefox. But if I loaded this page in Safari or Chrome, it loads very well.

  Here is the URL of the page to take a look:
  _{Specific link removed by moderator display ~ J99} < sitename >.com/top-10/top...services/

  No idea why this might be happening or how to fix it? I don't know if it's just my computer, or if others have the same problem.

  Thanks in advance,

  Mike

  There's two of us have confirmed the page will load so I deleted the link to display as it could be construed as advertising.

  P.S. Note only forum content in the resolved threads is now indexed by search engines.

  (Last updated: February 14, 2015 08:45 CEST)

  Solved the locked thread now ~ J99

• Combustion/Video Playback problems since again 'fixed' update drivers for TSST L632H

  Hi guys,.

  Since I updated my drivers for my DVD playback was terrible, and it takes 30 to 45 minutes to burn a CD.

  Has anyone experience this problem? I'm fairly muted, I would like to restore my drivers but then iTunes may stop working.

  
  

• Problems with the Firewire Audio Interfaces

  I use a Presonus Firebox for all of my recording and playback. I just bought a new pc HP with Vista64 and I had problems with my audio since then. Symptoms include random audio dropouts, crackling sounds when you scroll through the menus in my software, no noise at all from windows media, no windows generally sound player. Everything works sometimes, but inevitably fails. Once the audio is de-energized my only solution is to restart the computer, and then it still doesn't work sometimes. I don't understand. My last computer was a couple of years and built the hand. It worked perfectly with this unit until the motherboard is dead after what I bought my new HP desktop with terrible results. The main difference between my pc and this one is that I was using XP and XP64. However, I have the right drivers for the home and the computer recognizes it but I can't operate consistantly and correctly. This new HP has more power than my last, and more then enough power for my needs recording software. I would like to know, I've been recording music on PC for 8 years. Any advice would be welcome.

  I am now convinced that the long nightmare is finally over. I tested my home over and over again with no failures. Record and playback midi seem to work perfectly. Here's what I did:
  
  1 optimized my computer for audio streaming using the guide written by sweetwater.com.
  
  2 uninstall all the drivers from Presonus and all software, including the removal of all PreSonus files on the registry using the instructions provided by the technical support of PreSonus.
  
  3 disabled WLAN and then physically disconnected from the motherboard.
  
  4. my computer has two firewire ports. The front port was connected to the motherboard via a short cable. I physically unplugged the cable from the motherboard.
  
  5. I bought an Express(1x) PCI firewire 400 card with a Texas Instruments chipset. The exact brand is inner Pro PCI Express(1x) 4 port 1394 a. The firewire card is a power port. I plugged the power jack on the same line, connected to the DVD player. I don't know if it's important, but I'll try to document EXACTLY what I did. The firewire card requires no driver work. It came with a disc with a B.S. video editing software I was not installed.
  
  6. I turned on my computer and disabled the built-in firewire in Device Manager, leaving only the new active firewire card.
  
  7. I installed the drivers from the Firebox from the original disc supplied with my unit (v1.20.0). I had good results from these pilots in the past that may be because I use XPsp2.
  
  8. I have connected the combustion chamber when prompted to by the installation software.
  
  9. rebooted the computer with the combustion chamber connected and everything's fine.
  
  By the way:
  
  The inner firewire card cost me $ 30.00
  
  My computer specs are:
  HP a6745f desktop
  Dual core AMD 5050e 2.6 GHz
  XP sp2
  GigsRAM 4 (3.25 because I'm on XP)
  
  If you are confused in the store on the question of whether a firewire card uses a Texas Instruments chipset. Try to get a glance at the map. You should see a chip bearing the logo of TI: the State of Texas, w / Ti. YeeeeeeeHawwwww!

• Problem of C50-A-19 t satellite with TOSHIBA Recovery Media Creator

  When I try to do recovery dvd with TOSHIBA Recovery Media Creator burning fails.

  I have the Satellite C50-A-19 t with TSSTcorpCDDVDW_SU-208DB_T cd/dvd-rw unit.

  During combustion process, I get an error saying it is impossible read the file D:\ZZImages\ZZImages\install29.swm (file .swm in error change with different attempts).

  I selected the option to verify the dvd after burning.

  I tried several times: I try to make one dvd (requires 3 DVDs for a full recovery).
  I try 2 times with verbatim dvd + are trying the fist failed, the second succeeded with the same kind of support.
  I try to numb DVDs. 2. for two times with dvd - r and dvd + r support and it has not yet.

  On the windows error reporting, I find this error:

  and this alert:

  + Updated Firmware ODD problems with Toshiba Recovery CD Creator +.

  I see this solution to update firmware for different models of units of cd/dvd-rw

  http://APS2.toshiba-tro.de/KB0/TSB9C02RP0000R01.htm

  but not on the model I have.

  I have:

  TOSHIBA Recovery Media Creator version: 3.1.02.55065006
  Windows 8.1 x 64.

  Is there a solution?
  is a known problem?

  Thank you

  Elena

  > I don't have a free USB key to test the usb mode.
  I recommend you to buy a separate USB memory key and to create the eventual recovery USB flash memory support.

  Please also check this other procedure described in this HowTO from Toshiba
  [How to create a recovery media USB flash drive to the valorisation of the ISO images - or (DVD) discs | http://aps2.toshiba-tro.de/kb0/HTD4103KB0000R01.htm]

  Comments are greatly appreciated

• Satellite L750D - update BIOS causing the CD Player problems

  I have a L750D-1GC Satellite running Windows 7. Recently I updated the BIOS to 1.60 04/05/12 THIS worm 1.40

  I noticed that since that more that I have problems my CD player in what I can read CD/DVD but does not burn. Using burning software, it appears the combustion happens (rotation of the disk and green light), but at the end it breaks down. I have tried several Microsoft Fixit program but the problem persists, help?

  I put t think that the BIOS update would impact on the functionality of CD/DVD drive.
  Usually, the firmware of the CD/DVD drive contains information about the compatible media and I put t that any link between this question and the previous update of the BIOS.

  For me is looks like the laser lens is dirty or the lens may not be properly calibrated to read/write from the disk
  Try to clean the laser lens with cotton wool trick and liquid alcohol in many cases this would set similar question and the player couldn't handle the media properly.

• Creation of Windows DVD, encoding of problems/gel/stops

  I am trying to burn a DVD video disc of dvr - ms files, but I had tons of problems with DVD Maker included in Windows 7.

  I am burning 2 files dvr - ms to about 1.75 hours of video each (3.5hrs) total on a DVD + r double layer everything goes well when I slipped the creation of DVD files and previews work very well.

  DVD Maker encoding start quite well until ' he reached about 80% of the encoding, then suddenly goes to 99% encoding and said that "year error occurred when burning the DVD. The burning process, even n start (my DVD is left intact) and the error message is not very useful. I have disabled all codecs (in the options), changed the media disc, even tried to burn on a virtual, also try burner on a clean install of 7 in a VM, still no luck. I tried to re - encode the file in some AVI files, but now it takes hours to burn a single DVD (I'm still 36% after 2.5 hours, I'll see if it works)

  I tried on another computer Windows 7, still the same problem except that DVD Maker stops encoding to 74.9% with no error message, or whatever, the progress bar is just frozen. If I cancel, DVD Maker freezes with the half-burned DVD, and I reboot to unlock the drive.

  Dvr - ms files come straight from Media Center (Vista).

  A strange thing is that Live Movie Maker says that a DVD DL can contain up to 3 hours of video, so the DVD Maker says that it can hold 5 hrs? Is this a bug or is it simply because the coding compression used is different?

  Go I love Windows 7 but DVD Maker from Microsoft really needs a rejuvenation treatment technical for coding and the combustion process. It shouldn't be so complicated that burn a dvr - ms to DVD file, seriously.

  EDIT: It worked when converting dvr - ms to avi files, but now I'm getting burning problems. DVD Maker says "Please enter another recordable DVD" to a disc after burning (because he has got more capacity?), and 2 other discs have their last chapters not readable. It seems DVD Maker not is not able to adapt the videos on the disc, even if she says I 30 minutes left on the disc when you drag the videos first?

  EDIT: It finally worked. I re-encoded avi files dvr - ms files. Then I burned all the DVD using DVD Maker on Virtual CD, virtual cd burner. I then burned the ISO resulting with 7 isoburn. But I don't think that an average user could do that, it's a bit too complicated. My burner is a year old and supports writing dual layer. Why is not able to burn directly to DVD to DVD Maker remains fuzzy.

• HP Pavilion dv6 Notebook problems and I know that this is not a virus

  Hello everyone I need help! :[

  Right now I feel "AAAAAAAARGHHH!", because my laptop was bad, since we bought it on Amazon. I got it for everything... 1-2 months (we got it in June) and I had problems really bad-_-"'

  The following events did my hair set on fire:

  Random memory dumps and no explanation for it (it says something like NO INFO DATA or something like that)

  My laptop is so freakin ' hot my legs are close to combustion

  It freezes at startup times and makes me do a difficult start

  It freezes when everything is STABLE!  I move my mouse sometimes and poof! FREEZE ALERT

  It is weird stuff at the beginning up resembling CHKDSK and boot scan, but I'm not so sure...

  So can someone help? Its under the warrantyso I could do maybe deported but I don't really know what is wrong first

  Here is some info:

  Laptop: HP Pavilion dv6 Notebook PC
  Processorentium (R) Dual-Core CPU T4200 @ 2.00 ghz 2.00 Ghz
  Memory (RAM): 4.00 GB
  System: 32-bit operating system

  Help :/

  your first mistake is to use the laptop on your lap. In the manual it says do not for this. never. Looks like your laptop is random questions causing overheating (probably by something blocking the ventilation openings) with the system board. If it is under warranty. maintenance operation.

• problems burning to disc at the library

  I have a problem burning a cd to the library, the drivers say they work but I have no sound and when I try to burn just says: error complete combustion

  There is no noise and it won't play either. the cd plays on other devices, including other computers, my library of music already burned times

  can someone help me please?

  Hi gillsharp,

  Thanks for posting your query in Microsoft Community.

  I understand that you are unable to burn the disc at the library, when you try to burn, it says error complete combustion, and there is no sound.

  1. what applications do you use?

  2. you burn a music library on a CD with Windows Media Player?

  3. What is the accurate and complete error message?

  4. What is the brand and model of the computer?

  Please follow the steps mentioned in the links below

  http://Windows.Microsoft.com/en-us/Windows7/change-settings-for-burning-a-CD-or-DVD-in-Windows-Media-Player

  http://Windows.Microsoft.com/en-us/Windows7/burn-a-CD-or-DVD-in-Windows-Media-Player-frequently-asked-questions

  Method 3:

  Please run the fixit from Microsoft mentioned in the link below.

  http://support.Microsoft.com/mats/cd_dvd_drive_problems

  Also check out the links below.

  http://Windows.Microsoft.com/en-us/Windows7/open-the-playing-and-burning-CDs-DVDs-and-BluRay-discs-Troubleshooter

  http://Windows.Microsoft.com/en-us/Windows7/burn-a-CD-or-DVD-in-Windows-Media-Player

  Burn a CD or DVD in Windows Explorer

  http://Windows.Microsoft.com/en-us/Windows7/burn-a-CD-or-DVD-in-Windows-Explorer

  Please follow these recommended steps, review the additional information provided and after back if you still experience the issue. I will be happy to provide you with additional options available that you can use to get this resolved.

• Problem burning files on DVD-R disc

  Yesterday, to make room on my laptop Windows 8, I started burning files on DVD-R discs.  I have an average combustion 4.18 GB on 4.7 GB discs with great success.  Today, I tried to continue the exact same process, but I keep getting warnings that there is not enough space on the disc and I need 2 more GB of space.  Nothing has changed.  The same discs, same type of file.  Everything is exactly the same thing, so why I get the warning?  This happened to me in the past with my computer laptop windows 7 and different flash drives.  For example.  I had an empty 16 GB flash drive that I tried to add the 5 GB file and I got a warning that the flash player was not large enough to hold the file.  I'd appreciate any help I can get.

  Hi Christophe,

  Thanks for posting your query in Microsoft Community.

  I understand the inconvenience that you face. Let me help you solve the issue.

  I would be grateful if you can provide us with the following information to help us better understand the issue.

  • What burning software you use to burn the CD/DVD?
  • You did it all change before this problem?
  • What is the exact error message you get to the screen?

  First of all, you need to cancel all the files waiting to be burned, so I suggest you try the following steps to burn the files using Windows Media Player.

  Burn a CD or DVD in Windows Media Player
  http://Windows.Microsoft.com/en-GB/Windows-8/burn-CD-or-DVD-Media-Player

  Keep us updated on Windows related queries and we will be happy to help you further.

• DVD burning problem: I burn the movie on widescreen PAL on a DVD-R disc. I managed it burned without menu. Now, I've added a "Pan and Zoom" menu with a main marker at 00:00:00:00, 21 scene markers, and a stop at 01:29:32:17 (th

  DVD burning problem: I burn the movie on widescreen PAL on a DVD-R disc. I managed it burned without menu. I have now added a "Pan and Zoom" menu with a main marker at 00:00:00:00, 21 scene markers and a cleat to 01:29:32:17 (the end of the film). The combustion is interrupted with a message to watch a C:\Users\ianle_000\Documents\20151206160446.iso file. There is no file. The message also provides a link for an explanation. This Web page is impossible to obtain. I'm running on a PC with Windows 8.1.

  Thank you once again. I burned the DVD!

  It is the first film for which I have reached the stage of burning. I'm not sure why she didn't in the first place. I tried to burn the "no menu" version, but at the time, was shot the DVD itself - I wonder when he reached this point?

  So, I burned the "no menu" version to another DVD, that worked, then the version of menu, with no cleat to a third DVD, which reads perfectly.

  Now that I have a successful routine, I'll stick to it.

  Thanks for all your help.

  I'll close this discussion now.

• problem inserting of titles in long audio file

  I use audition 2.0 and work with audio tracks for a long time, in which I use markers to track during combustion.

  My problem is that once I have burn the project, while the tracks are there, the names of the tracks (names) are NOT appear when I test in Windows Media Player.

  I used the hearing for years, but this little problem me stumpted.

  Marker type I select is a marker for 'track '.

  I typed the name of "label".

  In the dialog box 'CD list follow the use', I've fiddled with every imaginable combination of things to the list or remove them from the list.

  After the insertion of markers, I 'mix' ed or "recorded under" reinserted, or just parked in the CD session and burned.

  I read the forums and my book of hearing class and I can't source a solution.

  I need names appear in my songs. What escapes me, please?

  Thank you

  Allen anderson wrote:

  If the hearing cannot score the runs for common players such as WMP can read labels, what other software would recommend that I would incorporate my mixer?

  The whole issue is a problem WMP, not a hearing one. WMP does not read what is actually on the disk at all - it reads the UPC/EAN code, and search relevant information stored on the disk - which fails to do in the case of your home one, obviously.

  Writing of CD-text only written the artist and title, with the UPC/EAN. If you want to get WMP to read the CD-text at all, must have WMP 10, and must also have the plugin WMPCDText to go with it before it will show. If you want more information, look here.