HP laptop 110-1125: new hard drive, do not start

Similar Questions

• G62: New hard drive does not start after recovery.

  I installed a new hard drive after my old a bi dust.

  I ran the recovery from the discs of HP.

  After formatting the disk and copy files, it won't boot from the disk.

  I changed the boot order and tested the drive in the BIOS.

  What Miss me?

  The new hard drive sometimes requires to prepare first with utility cd from Cyberlink. Download and save the file. Once the download is complete, place a blank cd in your drive and click on the file to create a boot cd. Start with this cd and wait until you get a green check mark indicates the hard disk is ready. Remove the cd, insert the first disc of recovery and restart the laptop.

  http://FTP.HP.com/pub/softlib/software11/COL32372/ pv-80183-1/sp44645.exe

• New hard drive does not start

  I have a T61 with XP on it. The factory hard drive was beginning to show its age, so I got a 500GB WD Black drive for her. I used Acronis True Image to clone the old hard drive to the new. I used my counter top to do the cloning. When I plug the new disk in, the cursor just blinks and it will not start.

  I thought that maybe the clone was bad, so I put the new drive hard back at the top of my desk and is able to boot all the way to the windows start screen. If I plug the old drive in the laptop, it starts very well, simply refuses to boot from the new drive.

  Guessed it.

  Put the new hard drive into the computer, put the old hard drive in a USB enclosure and done a CD boot Acronis, and made the clone of the laptop. Runs like a champ and now flies.

• After the new HARD drive does not start installation Qosmio G15

  I just got this G15 last week and one of the hard drives was bad. Put it in a new Bay 2 and it does not start. I took it back and it starts fine. I even changed the main hard drive Bay 2 HD and it starts up fine with a hard drive. It's something to do with the scores, I think. Any help appreciated.

  Hello
  I think that the boot order has been the bad HARD drive in the BIOS.
  At the new disk you do not installed any OS, and in my opinion, this is a reason for starting problems.
  Simply access the BIOS and change the boot order

• Reinstallation of Windows XP Home Edition (new hard drive) does not start properly, please help

  I have a HP Pavilion zd7000 that bad on the hard drive. I bought another and used the reinstallation disc to reinstall Windows Home Edition.  Everything seemed to go well, but it starts now to a HP Invent logo black screen that says press F10 to go together to the top and F12 at startup of Lan.  Then, a second black screen appears that says press F1 to resume or F10 Setup.  I press F1 and Windows loads very well.  What can I do to have Windows load immediately without going through this?  Any help will be greatly appreciated!  Thank you much in advance!

  EverWin... IT WORKED! I can't THANK YOU enough!  I've been to every site I could find... begging someone to help me.  Audit throughout the day (for a week) to see if someone had answered... tried everything!  I'm so happy (and tired) I could just cry.  I can't believe that you took the time to help me... I appreciate it very much!

  God bless you!

• DV9000 new hard drive does not start

  DV9000 had smart hd HD replace failure did it, now, it will not boot from the cd to retrieve records. All I get is the operating system not found. Help, please

  OK... after a lot of trial and error. This works.
  ISO created from files that I found on the Internet for vista Home premium 64-bit
  Then used wintoflash to make the stick bootable flash... fail. tried again a portable my passport HD success!. Will boot from the external drive but not a flash player.

• Satellite Pro 2100 - new HARD drive is not booting

  Hello
  I wanted to update my SP2100 with a WD1200BEVE. (120 GB of WD).

  Copy of disk via USB + speakers worked, but after changing the disc nine does not start: the laptop hangs up with blinking cursor.
  Already checked that the partition is active and even a new installation from a CD of XP has the same result! The BIOS seems to accept the drive (if not installing via CD should have failed) so where is the problem?

  Any tips?

  Hi Kannengiesser,

  Which is really strange that you can t start up disk even it s recognized in BIOS correctly...

  You have the Toshiba Recovery disk? If so, you can try this disc factory settings. If it works, it was just an installation problem.

  But I couldn't imagine also that the new HARD drive is not working properly last week I had a similar problem. Made a HARD drive upgrade, but a few days later Windows didn't start because the HARD drive had a bad sector, now I'm waiting for a replacement drive.

• Re: Tecra 9100 - new HARD drive is not detected

  I have a Toshiba Harddisk provide a Tecra 9100. Checking the BIOS it shows "Enhanced IDE", but you are trying to boot from the disc does not work HARD. Even trying to install a new operating system present, that the HARD drive is not detected.
  From the laptop is also very long.
  Any idea?

  Your new HARD drive is larger than 120 GB? The HARD disk controller supports the 28-bit LBA and large drives as 120 GB will not be recognized by the BIOS.

  What you mean with Enhanced IDE? The BIOS recognizes the new HARD drive with model number?

• Satellite M30x - new HARD drive does not work

  Hello.

  I am installing a new ATA 2.5 "internal hard drive for my Toshiba M30X-166. The drive is a Seagate Momentus 5400.3 120 GB model. The laptop does not recognize the disc and no related error message appears, and in the BIOS, it shows as "HD not available."

  I put this drive in an external USB - IDE enclosure and was detected by my desktop PC, and I was able to partition and format the Momentus, so I know the drive is indeed work, but my M30X still does not detect the drive.

  What can I do to make the laptop recognize this unit? The BIOS M30X is: Phoenix EAL20 version 1.90.

  Thanks for your help.

  Hello!

  Have you tried another HARD drive? The new HARD drive is may not compatible with the laptop or does work does not correctly.

  Normally, a 120 GB HARD drive should work because the laptop has a limitation of LBA 28 bits and so you can only use hard drives 120 GB.
  In the worst cases, the HARD disk on the motherboard controller is defective :(

  Good bye

• (brand new) hard drive 0 not found (Latitude D600)

  ======================================================

  I know this has been discussed a lot, but I have not found a solution.

  My laptop is a Dell Latitude D600, BIOS Version: A16

  My HARD drive died last week, he was making noises that I made backups.

  Of course, one morning I turned it on and it says '... ". hard drive 0 not found... »

  So I thought right we'll buy a new one, no big deal. In this case.

  But to my horror, the brand-spanking-new HARD drive made me exactly the same thing!

  Costs of the antistatic packaging, directly in the cradle, with tenderness.

  "First hard drive 0 not found '.

  No bootable devices - strike F1 to retry boot, F2 for Setup utility.

  Also, the BIOS reads my "main hard drive: ' as 'None '.

  I tried: -.

  -Replace (re-attachment for cradle clamp, tighten, etc..)

  -reset of the BIOS (pressing ALT - F)

  -internal 'HDD' isolation in the "boot order" (BIOS)

  -startup WinXP CD to format (says also that it cannot detect a HARD drive)

  -stroked and tweaked every possible BIOS setting

  -a ran the diagnostics (well Yes, tells me that it cannot find a HARD disk)

  -check the temperature (not a problem at all)

  I bought my D600 to opportunity without boot floppies or manuals, and private security has passed.

  I'll try to take out the battery for a day to see if that will be "flash BIOS" but I can't help you as (to my knowledge) the motherboard settings remain stored with the help of a small battery attached to the actual motherboard that would be inside the envelope, so I think it's a misunderstanding in another post on the forum , but I'll try it in desperation anyway. Next step would be to open the envelope and checking the IDE and remove the battery from the motherboard for 5-10 minutes.

  After that, my only option is to send to some local business PC repair. Ick.

  Any help will be VERY appreciated! Thank you.

  
  

• A1103 new Ram and HARD drive will not start

  Hello.

  I have a Mac mini A1103. When I got there the folder flashing with question mark. I got a macbook earlier where this problem was solved by installing a new hard drive. so I ordered a new 160 GB IDE 2.5 "5400 RPM and 1 GB Corsair Valueselect DDR1 333 MHz hoping that this will help me get the mini running and preforming a little better with 512 MB of Ram.

  When I boot the mini after swapping ram and hard drive I always see the same flashing folder. I can reset the NVRAM Boot, enter diskmode target? (I think) and the Boot Manager.

  When I enter the Boot Manager I can see the following screen

  

  a few times I get to this screen for Open Firmware screen where I can use certain commands such as vram-reset reset-all rebot and so, but sometimes I'm just stuck on this screen.

  Anyone have any suggestions on what is wrong and what I can try next? I do not have the boot original dvd but I have a usb bootable with IOS 10.6 and a dvd with IOS 10.6 (not original) but I can't get botting from any of the devices.

  A Mac Mini A1103 has a G4 Power PC processor and cannot be greater than 10.5.8. Superior OSX versions require an Intel processor.

  In this statement "a usb bootable with IOS 10.6 and a dvd with IOS 10.6 (not original)" I think you mean OSX, not of iOS. You must obtain a copy of the original installation disc which was 10.3 or 10.4 or disk to upgrade to 10.4 or 10.5 full retail. Coverall A1103 all three 2005 models of the Mac Mini G4.

  You cannot use a grey disc unless it was delivered with your specific Mac.  Native gray disc with Macs and can not e used on the other model of disc.

  You can probably call Apple and order a copy of the original disks

• New HARD drive is not recognized on Tecra M1

  Hello

  I am new to this forum, so apologies if this is an old question.

  My Tecra M1 gave a quality service for the past 6 years, but recently, the Toshiba management console has put a message saying that the HARD drive will fail quickly.

  I loaded immediately turned off my main files before you remove the HARD drive. It is a Toshiba MK6022gax 60 gig IDE hard drive. I bought a new disc of gigabytes of 60 MK6022gax, but when I mounted this same I got the error message "error ide #0". Installation XP or the BIOS can see this new record.

  I then reassembled the old HARD drive, which started OK. I then mounted the new disk in a USB enclosure, initialized, partitioned and quick formatted using the XP disk management. He picked up OK. Then I copied some files to it and read them back with no problems, then the drive itself works very well. But when I plug as the main 'C' drive, I get the error message again and is not recognized by the bios or XP put in place.

  Clearly, there is some BIOS (?) or startup procedure I have to do to get this recognized record. Help!

  I have Tecra M1 long with 60 GB HARD drive. Right now, I've updated compatible HDD TOSHIBA HDD 2184 B.
  I can confirm that the HARD drive is recognized correctly and I actually have the new install of WXP Pro.

  In any case, have you tried to upgrade the BIOS to the default settings?
  As far as I know that nothing should be set before you put the new HARD drive and it must be recognized correctly.

• New hard drive does not appear in the disk utility

  I am installing a new hard drive in my late 2011 13 "MacBook Pro. I started using apple's online retrieval system and went to disk utility. I tried to format the drive, but he is stuck saying "remove disc" for about a half hour, and then I had a rotation beach ball and could not move the cursor. I restarted the computer and now the drive does not appear in the disk utility. Any help is appreciated as I have no idea where to go from here.

  Thank you.

  You will may be turned off and check that your hard drive is correctly positioned with all the screws tight.

• Can't reinstall XP service pack 3 on the new hard drive, will not cross of EULA

  Computer VOstro 220 (Dell) under the age of 18 months. Internal HD died and was replaced two weeks ago with a HD internal 320, the speed of 7200 Western Digital. (Micro Center, a computer store large installed the HD that I bought at the store)

  I used the OEM "reinstall Windows XP service Pack 3" DVD.  With F12 I put the computer to boot from the DVD.

  DVD boots, I chose the option to install the OS

  Fisrt I see the message that the program checks the material. No error message

  Then I see the screen with the words "Windows Setup". Five minutes later, Microsoft EULA (end-user contract) is displayed.  IT does not scroll, I used the arrow keys on the keyboard to get at the end of the EULA was waiting for some kind of "type option"I agree". But there is nothing.

  Nothing more happens. No additional configuration.

  What is the problem? What should I do to get the Windows XP installation to continue?

  Why not install the operating system?

  Anywhere between 5 and 20% (depending on the production) new hard disks are defective. Test your drive with the factory utility.

  Hard drive test - CD Bootable:
  If you have a new hard drive Seagate the very next thing would be to download Seagate Seatools (bootable CD)
  and check bad sectors:
  http://www.Seagate.com/WW/v/index.jsp?locale=en-us&name=SeaTools&vgnextoid=720bd20cacdec010VgnVCM100000dd04090aRCRD

  For Western Digital readers to download the .iso from WdDiag file: http://support.wdc.com/product/download.asp?groupid=611&sid=30&lang=en

  Samsung Estool: http://www.samsung.com/global/business/hdd/support/utilities/ES_Tool.html
  Samsung Disk Manager software: http://www.samsung.com/Products/HardDiskDrive/utilities/shdiag.htm
  Hitachi Drive Fitness Test Software: http://www.hgst.com/hdd/support/download.htm#DFT
  Diagnostic tool available for use by customers who feel their Toshiba brand Fujitsu hard drive:
  http://SDD.Toshiba.com/main.aspx?path=ServicesandSupport/WarrantySupport/SoftwareUtilities
  Notice of suport Fujitsu disk utility: http://www.fujitsu.com/us/services/computing/storage/hdd/
  Toshiba CD bootable: (BACK Diagnostic Tool version 7.0 for IDE/ATA/SATA hard disks)
  http://SDD.Toshiba.com/main.aspx?path=ServicesSupport/FujitsuDrivesUSandCanada/SoftwareUtilities#diagnostic

  JS
  http://www.PAGESTART.com

  Never be afraid to ask. This forum has some of the best people in the world to help.

• R51 new HARD drive will not restore factory correctly state with discs

  I caught a HDD of 80 GB on old computer my gf, and I thought I would use it to replace the 40 GB hard drive in my ThinkPad R51.  There is not really important info on my old hdd, so I just created a factory recovery disks, put on the new hard drive (both are PATA) and ran from Rescue and Recovery.  After completing restore to factory state all the new hard drive will do is Rescue and new Recovery charge.  It does not load Windows.  Is there anything else I need to do?

  Shot in the hip here, but ISTR that some versions of R & R restore the image of 'restoration' in HD, then you restart to R & R and run a restore it to complete the restore of the rest of the car.

  As I said, just something I've seen elsewhere.  Worth, perhaps,

  Z.