HP mini 110-3600evPC: Webcam not recognized

Similar Questions

• HP Mini 110-3500 does not start

  HP Mini 110-3500 will not start. When I try to start I get a prompt back "BOOTMGR is missing" & «Press Ctrl + Alt + Delete to restart»

  I tried a "Factory Image Restore" and it failed with an ERROR msg '0xe0efooo3 '.

  Any help is appreciated.

  Sorry to hear that Geezer.

  You need to replace the HARD drive and reload the operating system.

  REO

• Logitech C310 Webcam not recognized

  I have a Mac Mini from 2012 which I just upgraded to Sierra. Everything went well except the webcam, a Logitech C310, is not recognized by the operating system. He keeps his identification as "unknown device". It doesn't seem to work properly, but I fear that it is not properly recognized by the operating system.

  Anyone else have a similar problem with a Logitech webcam that faces a problem?

  Contact Logitech technical support. The camera may be incompatible.

• NB200 - Webcam not recognized

  Hi, hope someone can help with this!

  Webcam is not working. Under Windows XP. Does not appear in the devices in Control Panel > system > device

  For a while, I kept getting the error message "USB device not recognized" when I start the computer, and then whenever I adjusted the screen, so those who were probably related. ?:|

  Updated the driver and USB issue went, but when I try to open the Camera Assistant Software, it says "Webcam is either disabled or failed.» Please check your webcam settings. »

  (X-)

  Thoughts?

  Hello

  I recommend first load default settings in the BIOS. Save these settings, exit the BIOS and restart your laptop.

  Then, make sure that the latest driver for the Toshiba webcam is installed. You can download it on the Toshiba site.
  In addition, it would be advisable to install the latest version of the BIOS. Visit the Toshiba page!

  In the worst case if you have the same problem after reinstalling the Toshiba Recovery disk it associated material s. This means that you should contact an authorized service provider. Guys can check the mobile and exchange equipment (webcam, cable or something else). Just get in touch with the guys and ask for help. From my own experience, I can say that they always try to help you as best we can.

  Good luck! :)

• HP Mini 110-4110sc: creator MIE HP Mini 110-4110SC are not not in downloads

  Hi people,

  I have a HP Mini 110-4110sc with broken HARD drive on my hands here and of course without recovery of support has been created by the owner when bought.

  Also, I found discussions on this forum regarding the download of the image and media creation of USB via HP MIE restore Image Creator covered here so I followed the procedure on page of download here, but the CRUMB image creator is all simply not in the list, and I can't find anywhere else... Any ideas?

  @Zhiwagoo

  Welcome to the HP Forums, it's a great place to get help, find answers and advice,
  Thanks for posting your request, I'll be more than happy to help you

  If I understand correctly you are need of the creator MIE to recreate the image on your computer and start using it again and after a lot of research,
  I found what appears to be a 3rd party link: click here

  Keep me posted and I wish you a good day
  
  Kind regards

• HP mini 110 Wireless does not

  Hello

  I use Hp Mini 110-3620st.  I tried the Broadcom driver, but still did not work.  Product number: LL890EA #AB8

  Please help me what to do.

  Thank you and waiting for your help.

  

  Hello:

  I would try to manually install the driver.

  If you have not deleted the driver installation folder, try this...

  Go to Device Manager and click on the network controller needing drivers.  Then click on the driver tab.

  Click on set to update driver.  Select travel it my computer for software driver and find the folder of the driver that was created when you ran the file.  This file will be located in C:\SWSetup\sp57965.

  Make sure that the include subfolders is selected and see if the pilot goes like this.

• DV9000 webcam not recognized

  have: dv9000 w / 1.3 megapixels, W7 Ultimate 64 bit

  question: webcam is not recognized and not recognized in (imaging device) Device Manager using belarc. so no webcam

  question: is the material connected to the mobo to be defective? bad connection to the webcam to the mobo? Can what tests I perform to determine the exact cause of having no webcam?

  If a train stops at a train station which then becomes a workstation work?

  Most likely the module webcam up upstairs behind the screen bezel went wrong. Very common. Other scenarios, such as the bad cable are possible, but not probable. The webcam module is so cheap that it pays to just buy one and try it first before you pull out your hair with other possible solutions:

  http://www.eBay.com/ITM/HP-Pavilion-dv9000-webcam-camera-w-cable-CMN5748-/360884943085?PT=PCA_Video_Conferencing_Webcams&hash=item54066b38ed

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• HP mini 110: help, do not know the password of BIOS for HP mini 110

  I have a HP mini 110 that was given to help our charity nonprofit. We do not have the BIOS password. The number is CNU94619YJ

  Hello:

  Try: e9lovg3oiw

  all are lowercase letters

  third letter is small case L

  small coming fourth and eighth letter O

  Concerning

  Visruth

• HP Mini 110-3101TU: HP Mini 110-3101TU is not compatible with Windows 10?

  I've been running my HP Mini laptop in Windows 7, IE11 with an external (extended desktop) Samsung SyncMaster LS23A300BS/XP with no problems of navigation. All drivers up to date. I received a free upgrade for Windows 10 I installed online 2 weeks ago and have not been able to make a good navigation on the internet yet, either on board or IE11: both crash in browsers after a 2nd or 3rd browser, blocking and the opening page process may not be finished in Manager tasks so that Windows can not stop (you need to disconnect). I followed all the advice, corrections and common sense (clean boot) pertaining to this crash, but nothing works. On top of this crash, there is a problem with the application of Windows Explorer which can not read a statement in memory at shutdown of Windows 10 and must be closed in the first place. The last problem occurs only (I think) when working with the external montor, when I work with the laptop only I've not seen this message (can not read the instructions...) when stopped down, but blocks the navigation happens tirelessly with one or two monitors.

  I played with the DNS (using automatic 8.8.8.8 etc. and DNS), I also run a PowerShell (tip forum) command and disabled non-Windows file extensions and all supplements but did not touch the registry other than adding two words for maximum 10 tabs/server. Nothing helps.

  Question: My Mini laptop too old and incompatible (surfing the internet) with Windows 10 or maybe Windows 10 faulty (buggy)?

  I am writing this post with my old Compac HP 8710p with the same monitor external but digital (DVI/HDMI cable) in VistaSP2 32bits Business that works like a 'charm' (pun intended). I could not even connect you to this forum with Windows (crash) 10.

  Any suggestions and help would be appreciated

  Track 5 September 19:00 (GMT + 8 hrs.)

  Not crashing with browsers (Edge and IE11) but still very slow and often-page response cannot be found and freeze, then after updating but I am now able to close the frozen pages (no more crashing, process in normal Task Manager). The message Windows Explorer app that it cannot read a statement in memory occurs that when my external browser is connected (2 active monitors) and does not show using my laptop just so it's probably Intel graphics driver related. I didn't know I was downloading Defender 5 updates yesterday that there is nowhere a notification in Windows, 10 with a slow (home, 2 G WIFI) internet connection may have caused some of my problems, but Microsoft has promised to look into the crash problems I brought today and I'll post the results shortly. I type this follow-up with my HP Mini and IE11, Windows 10...

  Frank

  To follow this thread on the Microsoft Forum please see:

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_10-networking/HP-mini-110-3101tu-not-compatible-with-Windows-10/262e92c9-5f73-4333-BC46-fb5b229fbdea

  Frank

  Updated: 9 September

  I found three issues that I fixed and most of the problems have disappeared now, internet Windows response is still slow compared to VistaSP2 and IE9 but which can improve with W10 updated.

  The last driver Synaptics touchpad from Synaptics and Windows 10 fix1 support web page: load automatically downloaded an update.

  Correction 2: Downloaded Intel driver 3150 8.14.10.2230 (2010) of the web page of the HP support and ran Windows 10 compatibility check, saved results to setup.exe and then install the (older) driver on my graphics driver (2015) Intel 3150 more recent that I have downloaded from the Intel support web page but is not compatible with the HP Mini 110 series. This caused the accidents of Edge and IE11 (zoom).

  Fix 3: run 2 commands (admin) NETSH: netsh winsock reset and netsh int ip reset c:\resetlog.txt which improves the response of browsers, but after restarting the need for procedures to be repeated, if all goes well in a future update of the W10, will address this issue.

  I think that my HP Mini is now compatible Windows 10

  Frank

• LIFECAM VX-1000 WEBCAM NOT RECOGNIZED ON MY LAPTOP ASUS

  VX-1000 camera is not recognized on my windows 7 64 bit operating system.

  I tried to install the software from the microsoft Web site, and it gives me an error message "THERE IS No. CAMERA CONNECTED to THIS COMPUTER"
  WHAT CAN I DO?

  Hi BaskijeLlupa,

  This problem may occur due to already installed a Logitech Webcam or if the LifeCam drivers are incorrectly installed.

  I suggest you try the procedure described in the article and see if it helps.

  Troubleshoot failures to find the new LifeCam hardware
  http://support.Microsoft.com/kb/929087

  Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:
  http://Windows.Microsoft.com/en-us/Windows7/back-up-the-registry

  Hope this information helps. If you need additional help or information on Windows, I'll be happy to help you.

• Webcam not recognized in Windows XP with VMware Fusion

  I use VMware Fusion 2.0 on a Macbook Pro with Windows XP.  I've been using Yahoo Messenger with the iSight webcam and I think I accidently deleted the icon at the bottom of the VMware window and now the web cam is not recognized in Windows at all.  The iSight camera works just fine under MacOS, but I can't find how to do Windows or VMware recognizes the camera.  I guess I could reinstall VMware and it might solve the problem but I'm looking for an easier route when it exists. Someone at - it a similar problem?

  Thank you

  Dennis

  Have you checked the settings of your virtual machine to see if the isight is activated must be forwarded to the VM?  You might consider checking or setting these options under usb.  Also if you have version 2.0 only then you can consider update 2.0.5 before reinstalling VMware.

• HP mini 110-3830nr does not connect to internet says network cards need drivers,.

  I have a hp mini 110-3830nr and I just replaced the HARD drive and reinstalled windows 7 starter(32bit) and I can't said online.it drivers.when network adapters need I go to Device Manager all therr have a yellow mark on them.here are the identifiers that you guys need so I hope you can tell me where to find the drivers.

  ethernET CONtroller - PCI\VEN_10EC & DEV_8136 & SUBSYS_3594103C & REV_05
  Controller network - PCI\VEN_1814 & DEV_5390 & SUBSYS_1636103C & REV_00
  Video controller - PCI VEN_8086 & DEV_A012 & SUBSYS_3594103C & REV_00

  Help, please.

  Try this for Ethernet controller:

  http://ftp.HP.com/pub/SoftPaq/sp52001-52500/sp52421.exe

• ASUS USB2.0 Webcam not recognized by Skype 6.18.0.106

  Hello members of the Skype community.

  given that I've updated Skype to the latest version 6.18.0.106, Skpype said that no camera was found that makes me unable to make video calls. In the previous version, my camera has worked without any problems. As a solution, I installed previous version of Skype, but since Skype is smart enough to detect not being is not up-to-date, it kept connect. I have some ideas how to solve my problem.

  My computer spec:
  ASUS N46VZ
  Intel i7-3610QM
  8 GB RAM
  Intel HD4000 & GeForce GT 650M
  ASUS USB2.0 Webcam
  Windows 7 Home Premium

  Best

  Try to uninstall the currently installed version and install Skype 6.14.0.104 version:

  http://download.Skype.com/MSI/SkypeSetup_6.14.0.104.msi

• ASUS My Cinema U3000 Mini DVB tuner is not recognized by Windows 7 - help!

  I am running Win 7 Ultimate (64 bit), and can not get the tuner DVB Asus recognized. Windows tried to install it as STK 7700 and failed miserably, so that the disk that came with it (and who worked under Vista Home Premium 32-bit) will install but won't play ball with the system either. Support of the Asus Web site is all serve as a firebreak to the chocolate, so I was wondering if anyone here knew of a workaround or a driver that would be acceptable for this version of windows. I tried to run it in compatibility mode with XP 64 and Vista Home Premium-32, but without success. The ecological part of hates me the thought of just binning a piece of kit by pretending incompatibility with Win 7 media center, any help and advice would be appreciated.

  Hi, I am user of Windows 7 and Asus MyCinema U3000. I found that the Version 3.1.0.1 driver for windows XP can also run Windows 7, it works really well for me =]

• Dell XPS M1210 webcam not recognizing not not driver on Windows 7

  I have a Dell XPS M1210 with Windows XP Home, I've upgraded to Vista and later to 7, the problem is when I upgraded to 7 I had problems because I didn't delete anything, after that I decided to reformat the laptop using windows 7 (by removing the entire partitions) and aftet 7 installation I downloaded all the drivers and everything worked well, except that the fan was makin a thud I decided to open the laptop everything cleaned up and put back. Calmed down after the noise of the fan, but the webcam no longer works, it says that it needs drivers, and when I install it, first time he told me plugged the cam (integrated cam), after uninstalling and installing the driver a couple of times, that the camera has detected during the installation of the driver, but after that when I try to use it it says that no cam is currently installed. When I go to the devices, it shows a unspecified device, the USB composite device. I have not been able to find a driver that actually works, or the problem may be the cam is not compatible with windows 7, or when I open the laptop, how can I find out which wire is the webcam. When I turn the cam cell phone makes a sound similar to when you plug a USB device I guess that it detects the cam for a few seconds, what could be the problem.

  Problem solved I downgrade from Vista Ultimate, download the drivers and all works correctly, the camera now works perfectly, I guess that logitech has not come with drivers for Windows 7...

  Thank you!!!