HP Pavilion DV6 HP Logo light on cover issue!

Similar Questions

• HP pavilion dv6-7010us: low light on dv6-7010us screen after replacing the screen

  We recently replaced a cracked screen on our laptop and now the screen is very dark. You can still see that the computer is turned on, but it is difficult to use. The brightness level is completely upward and the f command button does not help. How can I fix the light from the screen?

  Hi @Nantucket

  Welcome to the HP Forums!

  This is a wonderful place to find answers and advice!
  You have the best experience in the HP forum, I would like to draw your attention to the Guide of the HP Forums Learn how Post and more

  I understand that you have recently replaced a cracked screen but the news is very dark.  You can see that the computer is turned on bu that it is difficult to use.  The brightness level is set up and the F command button does not help.

  Have you checked to make sure that the connections are secure?

  Has been recommended for your laptop replacement?

  Here is a link to a display size troubleshooting (Windows 8, Windows 7 and Windows Vista) which can also help.

  Here is a link to HP Pavilion dv6 Entertainment PC Maintenance and Service of Guide for your laptop.  Was the recommended replacement?  Please note Chapter 3, page 23, section 1, a list.

  Good luck!

• I have a HP Pavilion dv6-2088dx, and the power light flashes constantly, that means?

  Help.

  I have a HP Pavilion dv6-2088dx and have had for a little less than two years now.  About 8 months ago, I replaced the original battery with a long life Rayovac battery.  Recently my laptop power light has been constantly intermittently to about 1 flash every 2 seconds, regardless of the level load and/or if its plugged to the power source.  What exactly my computer is trying to tell me?  Thanks for the help in advance

  -Kyle

  I found the link to your question.  I hope this helps.

  http://h10032.www1.HP.com/CTG/manual/c01884775.PDF

  

• Pavilion dv6 i3 with Window 7 64-bit. To start the HP logo appears, then I get a black screen

  I have a Pavilion dv6 i3 with Window 7 64-bit. To start the HP logo appears, then I get a black screen with a blinking cursor. I ran all the tests start and everything this past. I tried all F8, F9, F10, F11, recovery options with no luck. I tried to start with the ERD Window 7 64 bit I created when I install the laptop. Nothing... I did it with all the disconnected device. No luck. I'm looking for all the options until I re - install windows. I started with the Windows 7 recovery DVD and it reads, but I cancelled the process because it will reformat the hard drive and I expect to work around all the hassels of having settings to reinstall the software, etc.. Any ideas would be welcome.

  Thanks for the reply. I already tried these steps. I created a bootable floppy that I can get the data on the hard drive and am trying to restore windows to the recpvery of the DVD system that I ordered with the computer. Thank you

• HP Pavilion dv6-1030us will not light

  Hello

  HP Pavilion dv6-1030us laptop
  Windows Vista 64-bit

  This laptop was working fine when it was used earlier in the day. The food is good and the battery is good.

  When I press the power button, the led power and other lights in the upper part as well as the light output at the front lights up for about 1 second and then turns off. A few times, the lights stayed a little longer and I heard the fan turns on and perhaps the hard drive, but then he cut. Whenever the screen was completely black. No screen of boot or anything.

  I tried to pull the battery and now the power button for a minute, then replace the battery. That has not changed anything.

  I tried and I tried pulling the battery, pulling the RTC battery and now the power button for a minute, then replace the batteries. That has not changed anything.

  Does anyone have an idea as to what could be the problem?

  Thank you

  Calvin

  Hi Kyle,.

  I bought a new motherboard (motherboard) for about $65. I installed it and the laptop works fine now.

  Thank you very much!

  Calvin

  P.S. for those of you looking for a motherboard for this laptop, try searching for "HP 511863-001" and looking for a company that is reliable for the purchase of.

• Flashing light of HP Pavilion dv6-6c48us

  I have a HP Pavilion dv6-6c48us laptop.  It works fine, but I just noticed that when I connect a light starts flashing and

  stops when I log on.   The light is located on the right side at the bottom.  Is not on the keyboard, but on what I would

  qualify an indentation in the metal part above the stickers that were on the computer when I bought it.

  Should I worry?

  Thank you

  Charl

  You must make reference to the fingerprint reader led. There is nothing to worry.

  See the following image.

  

• HP pavilion dv6-1245dx won't boot screen logo, grid screen, caps lock, shift and numluck work

  * little background, my laptop works well before it happened, I stopped and then tried to power it using after a minute I Gilles down, it starts and then when I try to use internet, the display suddenly blacked out, thought it was the power so I tried to power it again I get is bright with no logo so I turn it on and turn it on again then it became lines graph form tried to check if keyboard works numlock and capslock not working when I press it, ang wireless volume does not work

  HP pavilion dv6-1245dx won't boot screen logo, grid screen, caps lock, shift, and numluck work.

  I tried to remove the battery and press hold power button almost 60 sec to reset the bios always the same, I tried the reinstallation of the memory 2 still the same please help

  problem solved... saw something on the forum about pressing f10 or f11 I randomly pressed start magically work

• Touchpad light shines when enabled on my HP Pavilion dv6. someone knows how to turn it on?

  I have a brand new HP Pavilion dv6-6260. I bought it only a couple of weeks.

  When I bought, if the touchpad is active, the light would shine white to indicate that he was active. However, last week, that seems to have changed and now when it is active the light does not shine.

  Oddly enough, when I turn off the touchpad the red light shines to let me know that it is not active.

  someone knows some way to re-enable this feature? the Visual indicator is useful for laptop users who are not blind, but with a visual impairment.

  Press FN + SPACEBAR for power turn the light of accentuation of touchpad

• HP Pavilion DV6-3014TX no longer lights

  Hello

  I have a HP pavilion dv6-3014TX.

  My brother has spread very little water on it. Now it no longer works.

  When I plug in the adapter, it used to be a white light flashes, indicating that the power is running. Now, this light is dead, what is the average power is not coming into the laptop.

  I tested the adapter, nothing wrong with it.

  I completely took apart my computer. I already did this time several before, dv6-3014TX has overheating problems and needs a lot of cleaning maintenance.

  The under keyboard was mainly wet. But noting appears to be damaged on the inside. I cut the water and back up my laptop. But same problem: the computer turns on, light still dead.

  I think the problem comes from the port where you plug in the adapter. It seems broken because of water poured around it.

  This can be changed very easily. But I can't find where to buy it.

  THX!

  Looks like it's toast.

  If you are looking for, try PartSurfer HP: http://partsurfer.hp.com

  You can also find parts in the interview Guide & Service: http://h10032.www1.hp.com/ctg/Manual/c02657339.pdf

• Pavilion dv6-3172ee: intel gpu graphics light dose?

  I have a very bad experience with computer hp pavilion Dv6, I have many problems with the GPU and overheating at the end of the corrupt GPU and now I need to buy and replace the new motherboard, but the only available motherboard is now one with INTEL ATI graphics card not, my question is if I replace the motherboard , does I'll suffer the problem of overheating yet? It is best to replace my motherboard with one that since intel GPU that can reduce global temperature?

  Note: my laptop is out of warranty.

  The first processors Intel Core of gen running hot, no doubt about that. But however hot it was running on the ATI card that it will run cooler with just the Intel graphics.

• HP Pavilion DV6-6031eo - black screen (backlight problem)

  I ve bought a new laptop Pavilion DV6-6031eo 2 weeks ago, and it worked fine until today.

  The question:

  When I turn on the laptop, it starts as usual and the system works perfectly, but the screen is black, so I can´t use it, unless you use another monitor, think I Don t want to. I think it has something to do with the backlight, or perhaps the retroeclairages cable routes.
  HP logo at the back of my screen used to light up when I turned on my laptop, but now it s too messed up.

  No backlight and no light in the HP logo.

  I ve sent an email to HP TotalCare, since I got my warranty (lasts 1 year) and I would like to know if they will cover it.

  Hopefully, I will get a response as soon as possible.

  Thank you.

  PS: Sorry for my bad English. I m of the Denmark, so it s not my mother tongue.

  Hello

  Guaranteed that you have on this model it will cover for you and your English is very good.

• Where are the Ports USB 3.0 of my HP Pavilion dv6-6158nr Notebook?

  I am unable to find the Ports of USB 3.0 on my HP Pavilion dv6-6158nr laptop.

  Please tell which side are these ports and how to get the maximum speed out of them?

  Hi Hanazir,

  You'll love this.

  Get a bright light and shine on the left side of the laptop.

  Now, get a magnifying glass and look carefully next to the USB ports.

  3.0 ports are marked with the logo 'SuperSpeed '. "SS".

  Similar to this, but very, very small!

  

  To get the maximum speed, use only with devices usb 3.0 - external hard drives, USB sticks, etc done to run with this technology.

  There is no harm in using the USB3 ports with usb devices 2.  In most cases, USB 2 devices work as expected when connected to a USB 3 port.  There are rare cases where the USB 2 device may not work when it is attached to a port USB 3.  Before you accuse the laptop / desktop or even the port and if your laptop don't not have a USB 2 port, then consider to plug a USB 3 hub that supports one or more USB 2 ports and try that.  A few specialized 2 USB devices require USB 2 connection - deal with it.

  Dragon tips

  USB 3 external drives: offset connection, more or less depending on your hub, your hardware and your player can add up to an unacceptable delay when you use a USB 3 hub in conjunction with port USB 3.  Huh?  Unless absolutely necessary, do not use a USB hub 3 with an external drive USB 3 - connect the USB 3 drive directly to your 3 USB port on the computer.

  Other usb devices 3 work well on the SIIG 7port USB 3.0 / 2.0 Hub - this is a very nice quality, IMO and is supported by its own power supply.  Nice.

  It's my pleasure to help.

  Click on the Thumbs-Up Kudos to show that you appreciate the help and time of our Experts.

  When the answer is a good fix or workaround, click accept as Solution !

  Although I strive to reflect best practices of HP, I do not work for HP.

• Pavilion dv6-3152sl: green and pink strips horizontal on the swith on screen - Pavilion dv6-3152sl

  When I turn on my Pavilion dv6-3152sl, immediately after you start at the bottom of the screen there is green and pink horizontal stripes, just when the Windows logo runs, who this time seems unclear. These scratches disappear as soon as the flashing blue light from Windows 7 Home Edition gives the chance to enter the password.

  What is the problem in my notebook? What can I do to make these abnormal bands don't not to be there for the laptop turn on?

  My laptop got switchable graphics AMD. They are ATI Mobility Radeon HD 4200 and AMD Mobility Radeon HD 5000 Series.

  Thank you for your support.

  Hey, @Italian_Chiara,.

  Thank you for joining the Forums HP's Support and welcome! It is a great place to ask questions, find solutions and get help from others in the community! I read your post on the Forums of HP Support. I wanted to join you and help! I understand that your HP Pavilion dv6-3152sl notebook PC startup, you see the Green and pink lines.

  Note Remove all USB devices. Disconnect all devices of non-essential, as these can cause some problems.

  If you connect your laptop to an external monitor, the lines appear on the screen to the external monitor also?

  Have you tried to Uninstall the graphics drivers? If this isn't the case, please uninstall and then restart the computer laptop twice.

  Have you tried to Reset the BIOS?

  Here is another option for you to try:

  • In Device Manager:
  • Click display adapters
  • Right-click on family Graphics
  • Select software update of the driver
  • Select search automatically for updated driver software.
  • The laptop must find and automatically install the updated driver. Once the installation is complete, restart your laptop twice.

  Have you tried using HP Support Assistant to automatically search for updates? Here is a link to the HP Support Assistant, if you need it. Simply download and run the application and it will help with the software and drivers on your system at the time of purchase or need to be updated.

• HP Pavilion dv6 - black screen on startup, but works using the secondary monitor?

  I use a Pavilion dv6 WV815AV, and I used it for 3 years now.

  I tried to start the computer and the fan and lights are lit, but not the monitor.  I tried to plug in my high school, and it's that now treats as if it were the only screen.  I had problems in the past of a few times where I would get past the HP logo, and then there would be a substantial delay where the screen remains black but be illuminated, but most of the time that he would go to the screen connection, and if not, a simple reboot managed to solve the problem.

  Thoughts on how should I solve it?

  Thank you!

  Hi mybluesock, sorry to hear that you have a problem with the monitor not just not. I did some research and I found a document that can help you. Click on the link for the document.     http://support.HP.com/us-en/document/c01997899

  If this does NOT resolve the problem, please do not hesitate to write back and I'll do more research on the issue.

  Thanks in advance

• Pavilion dv6-6156ea: display replacement

  I need a litte help, earlier my screen woudnt turn on unless I bent the lid of my portable computer at a certain angle. Now, its competely went and even the Hp Logo that lights up in the back corner of the lid woud affected in the same way. So is it possible to replace the Ribbon for the screen of my Hp pavilion dv6-6156ea without replacing the whole screen and if so I'd like to help /suggestions on different parts of the source and replacement

  any help will be greatly appreciated

  Yes it is possible, but I'm not sure that's the problem. Have you tried an external monitor? Unless it's off to an external monitor the problem is not the ribbon cable to the screen or the screen of the Control Panel, but a motherboard problem.

  Here is the Service Manual:

  Manual

  Cables:

  For use only with models of computer in the shadow dark and grey steel finish 644362-001

  For use only with models of computer gold butter, espresso black, linen white, blue Pacific, pink Pearlescent, Ruby and Red Red Sonoma finish 640423-001

  If yours is gray it is the part that you need to replace the display cable:

  Seven bucks on eBay

  For $ 7, it might be interesting to try a new cable but hanging on to an external monitor is free.

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.