HP Pavilion Elite HPE-530sc - I'm looking to the new graphics card (maybe)

Similar Questions

• Pavilion p6 - 2120t: Windows will not start with the new graphics card

  Installed a Zotac GT 740 profile down in my desktop PC graphics card HP Pavilion p6 - 2120t and now the PC does not start.

  HP Pavilion p6 - 2120t CTO desktop PC

  Configuration:
  Intel Pentium CPU [email protected]
  4.0 GB RAM
  Intel HD Graphics Driver version Family: 8.15.10.2291 dated 27/01/2011
  Motherboard: IPISB-CU (Carmel2) (1 open PCI Express 16 expansion slot pins)

  BIOS to Version 7.18

  Running:
  Windows 7 Home premium 64-bit w/service pack 1
  Two monitors (VGA, 1 digital port 1)

  Before installing the new graphics card, I replaced the power supply original 300w with a 400w power supply.

  For starters, I disabled the onboard graphics in Device Manager. Then, I opened the case and installed the GT-740 in the open PCI Express slot. I made sure that the card was fully engaged in the slot.

  I plugged both monitors to their connections voted on the new map.

  When I tried to boot the PC, the digital monitor displays the screen HP (the one that indicates which key support to achieve the start menu) and then frozen. No other entries of key or mouse have been accepted.

  The PC then sounds 4 short beeps (about 10 seconds between each beep) and then a long beep before turning off the signal to the screen.

  Then, I removed the new graphics card on the PC that starts then. I have reactivated the original graphics drivers and the PC then worked normally.

  Tried the above process two more times with the same results.

  I then went into the start menu to look at the BIOS. The menu of the BIOS shows two options:

  > Sources of boot UEFI

  Windows Boot Manager

  > Sources of boot legacy

  ATAP I CD/DVD player

  SATA2

  Hard drive

  SATA0

  Network controller (Realtek PXE B06 D00)

  PC using UEFI Boot Manager Windows boots normally

  I have not tried Legacy Boot Sources because I don't know which one to choose.

  I went to the HP site and looked for an update to the newest BIOS, but updating them is a rev version 7.16 while my PC shows my BIOS to version 7.18

  I know that others have had a similar problem but I have not seen a solution that works for my PC.

  Any advice would be welcome.
  Thanks for your time.

  Hello

  Your PC isn't spec'd to run Windows 7 using the Windows Boot Manager.  I expect to a UEFI-based graphics card likely to work on an HP PC that does not have a BIOS version 8.

  The below listed OEM HP, graphics cards should work in your PC using a normal non - UEFI W7 and W8 installation.

  

• Pavilion p6 - 2020t: HP-Pavilion will identify the new graphics card

  Hello

  I got a HP Pavilion for a few years now and never updated my BIOS (not that I know well). I'm trying to install a new graphics (gtx 750ti) card and the computer does not recognize it. It shows the first screen, and then a black screen and a beep, then it crashes. Keyboard does not work, cannot get into the BIOS.

  I tried everythign with current BIOS, boot legacy and ensuring that the Integrated GPU is disabled, and nothing works. I also did research on food, and but it is not terrible, it should work with this graphics card (the fan even spinning).

  According to my research, the current BIOS is simply not recognize, and I need to update. My current version is: FRIEND 7.16, 05/10/2011

  I navagate through the HP website and it said that the automatic update should update the BIOS for Windows 10, and it won't let me download all drivers (although the last BIOS update was 2011). I tried to enter the FRIEND's site and download it from there and it won't even install their drivers, it says that flash is not supported (probably for Windows 10).

  If someone could give me an idea of how can I get a newer version of the BIOS for my motherboard, it would be much appreciated as I'm pretty sure that's the reason why the computer is not recognizing the new graphics card

  The risk is that the video card is one that is for a newer PC with an EFI BIOS. That's why the empty card is not recognized.

  If you use a card equipped with a switch on the virtual card allowing the use in legacy and uefi BIOS it will work with the BIOS of your PC.

  Sapphire makes video cards that have this capability. Take a look at the catalogue. What you need is a PCIE x 16 card video with switchable legacy\uefi BIOS or legacy support, but not only UEFI.

  http://www.sapphiretech.com/catapage_tech.asp?cataid=8 & lang = eng

  You cannot change the type of BIOS that your PC has in the UEFI.  It's a question of his being of a generation of diferent from the PC.

• You are looking for a new graphics card with 1 GB of memory for Satellite Pro A10

  I am looking for a new video card with 1 GB of memory, preference but is RIMM memory ram in my office, but has a different type of memory in the description of the video cards.

  Is it important at all, the video card would work always?
  Thanks 1million
  Stephen

  I put t know exactly what you want to do, but I assume that you need this card for an upgrade.
  New bad guy! Laptop graphics cards are often fixed on the motherboard and cannot be deleted!
  In addition, you must know that the mobile graphics cards are simply different and you can't compare these chips with adapters for desktop PCs.

  Best regards

• Pavilion Elite HPE-170 t: need help with the result of a command prompt to Power Options

  I have recently upgraded to Windows 10 in Windows 7.  Like so many thousands of people, I problelms of sleep mode.  Mine will not be auto-sleep.  It has been suggested that I saw to run command prompt: powercfg-applications

  It supposedly will list the items running on your computer which can now be auto-sleep to work.  I tried several times and up to now, I get the same item displayed each time.  This is what is displayed: \device\harddiskvolume2\windows\sysWOW64\svchost.exe (hpqddsvc) is followed by this message: a file delete operation is underway

  My first thought is that if there is an operation to remove file in progress all the time, it's maybe the reason why my computer is not auto-sleep.  If there is someone out there who can shed some light on this situation, I would appreciate the help.

  EUREKA * SOLVED
  

  I found the answer to my problem!  After using the control system: powercfg-query and get the answer: \device\harddiskvolume2\windows\sysWOW64\svchost.exe (hpqddsvc) delete file operation is in progress

  I started looking for whatever it is associated with the answer above.  In the Manager of tasks in respect of the services, I found the name of the file hpqddsvc, with a description of HP CUE DeviceDiscovery Service was running.  When I stopped the task and re-tried in opt power standby mode, it worked correctly.  In the Configuration of the system (by typing msconfig at the run prompt) on the Services tab, I unchecked the box for HP CUE DeviceDiscovery Service and rebooted the computer.  The service is no longer running.

  I'm sure that this Service has been added to my computer when I downloaded the hp.com/support product detection tool .  The tool scans your computer to detect and identify HP products.

  This can be useful to others who have the problem of the auto-sleep I've had.

• HP Pavilion HPE h8 - 1213c: black screen of death because of the new graphics card (EVGA geforce gtx 960)

  I just bought a new card (EVGA geforce gtx 960) to kick some butt. But during installation, it seems to be held on a black screen of death? Not the most fun to see... in any case, I had asked the store clerk if it would work and he said to, but it doesn't seem like it does... Is there a new BIOS I should download or something? Any help would be nice...:.

  My computer is a HP Pavilion HPE h8 - 1213c

  The graphics card is an EVGA geforce gtx 960

  If you have both. You can use one or. PIN 8 can be used as a 6 pin as well.

  http://www.EVGA.com/products/ProductList.aspx?type=0 & Family = GeForce + 900 + Series + Family & Chipset = GTX + 960

  2 smaller cards use a single PIN 6. The rest use a single 8 pin.

• HP pavilion p6226it: can I upgrade my pc with a new graphics card?

  Hi, I have a hp pavilion p6226it, I would like to know if the graphc 7750 HD card would go well on my old pc.

  matherboard: M2N78-(Violet6)

  Processor: AMD Athlon II X 4 620

  RAM: 6 GB

  Graphics card: HD 4650

  Same expert people told me that I could have problems because of my matherboard and bios (I've never updated), is this true?

  @antonmartino,

  Hi again.  Just below the section for memory you'll find.  What you can do is take existing specifications and the specifications of the motherboard and see what card maximum that you can put in the slot.  The only thing you want to look at is what is the power required by the new map you found and if the power supply has enough power to stay with her horse.  If you talk to any place of the computer with the specifications of this page, that I gave you, they can give you the best option.  What I do is take the listed specifications of the card and match the cards, in that you are looking to put.  Check to see if it's the same dwelling and look to see if they require the same requirement for voltage and they should work perfectly.

  I hope this helps.

  Thanks again for the post and have a great day.

  HP Pavilion p6226it Desktop PC product specifications

• Recommendation for the new graphic card for the Pavilion a1250n Office running windows xp service pack 3

  trying to upgarde my pavilion a1250n computer of office for graphics card MSI r5450 radeon. After installation of the new card in the PCI express and turn on the machine, does not start, screen goes black and the fans to run at top speed. The card and the machine starts fine with the ATI radeon 200 exprees edge. I went into Device Manager and disabled the ATI radeon 200 adapter, and the system still wouldn't start with the new card. Went into the Bios at startup and changed the setting of the adapter PCI E, the slot where I put the card, and still won't work, even with the Bios and Device Manager changes I made.

  New card right out of the box, could be bad, or perhaps not compatible with my system? If is not compatible, what would you recommend? Currently I am running windows XP SP3 and am looking for a card that can be upgraded to Windows 7 64-bit. I know that the ATI integrated graphics card cannot be upgraded, so I'd appreciate some advice really.

  Thank you.

  John Perez

  Hi John,.

  The link above will show you how to clear the CMOS memory.  Just scroll down once you click on it.

  NVIDIA video cards are planned for a 300 Watt power supply

• HP Pavilion Elite HPE-400f: you are looking to upgrade to USB 3.0, takes my computer all supported?

  My motherboard is a card mother-N-Alvorix-RS880-formfat (Alvorix) , I want to switch to the usb 3.0 ports, my computer motherboard will be able to use 3.0 PCI-E PCI Express card I found some on ebay, I'm looking to buy one, but I want to make sure if my computer can handle the speed of usb 3.0?

  Will007, welcome to the forum.

  You will need to purchase a PCI Express x 1 card.  There are three of these locations on the motherboard.  I'm not sure you can see the full power of USB 3.0, but it will be certainly faster than USB 2.0.  Number of computers most recent didn't reach speeds of USB 3.0.

  Please click on the Thumbs up button '+' if I helped you and click on "Accept as Solution" If your problem is resolved.

• HP Pavilion Elite HPE: Windows Explorer can't see the folders/files

  My computer seems to have nuts. I have several times & suddenly (in minutes) began to receive messages "Windows Explorer is not responding", with choices such as "search solution and restart the program", "stop program", "wait." Also, it happened several times for Firefox.

  Right click on a folder on the desktop will block. In fact, who seemed to start the problem. I wanted to do a right-click & Delete a folder on the desktop.

  Can I use desktop shortcuts & open Office files, but I can't see the contents of the C drive, etc. Looks like it is filling when I click on "Computer", which will display all of the subfolders... a green bar moved from left to right at the top for more than an hour, but still no folders/files are displayed.

  It is now after midnight. I'll leave it as; non-stop. If all goes well, he rebuilds "pointers" or other & will be done by morning.

  

  Your computer is clean.

• HP Pavilion Elite HPE - 580t: could not find driver for integrated Ethernet card for desktop HPE 580t

  This desktop computer has been through a number of operating systems and should now have 10 32-bit Windows (for other software support needs).  All right, except that it lacks drivers for connection to Ethernet (built-in) on board.

  I tried the approach of Windows Update, the "update driver" and search HP, Intel, QLogic and other places of Ethernet NIC and Chipset drivers... nothing fits or works.  The hard drive has long been wiped, so there is no recovery partition, nor do I still support discs. :-(

  Is the reported by Device Manager hardware ID: PCI\VEN_14E4 & DEV_164A & SUBSYS_3070103C & REV_02.  164 a same device does not appear on the pci database. :-(

  Yet once again, I need to Win10 - 32-bit (no 64 - bit).  Thanks in advance for any help that can be given.

  Hello:

  There are no W10 driver for this chip ethernet I can find.

  In fact, everything that I could find were drivers for Windows Server 2003 and 2008.

  HP doesn't even have driver Broadcom ethernet on your PC support page, and I couldn't find the site of Broadcom or the other.

  I explored the Broadcom file and there is no support drivers for the hardware ID you have posted in the file.

  So, the only suggestion I can offer would be to try the driver I compressed upwards and attached below.

  Download and uncompress the file in its folder.

  Don't do anything with the files in the folder.

  Go to Device Manager and click on the ethernet controller requiring driver.

  Click the driver tab.  Click on set to update driver.

  Select her browse my computer for driver software option and navigate to the driver folder, that you unzipped.

  Make sure that the include subfolders is selected and see if the driver will install.

• Upgrading the PSU and GPU for my HP Pavilion Elite HPE-510 t

  Operaring system: Windows 7 64-bit

  CPU: Core i5-2500, 3.3 GHz

  Memory: 10 GB

  Video graphics card: GeForce GT 420 - OEM

  Hard drive: 1 TB

  Computer case: height: 38 cm (14.96 inches), width: 17 cm (6.69 inches), length: 41 cm (16,14 inches)

  Power supply: power supply 300W

  Several features of the product: HP Pavilion Elite HPE-510 t

  due to the diablo 3. I updated graphic setting the lowest. FPS is between 15-22 so I'm interested in upgrading my power supply HP Pavilion Elite HPE - 510 t(specs are above) and graphics card with the following, respectively:

  GPU: ASUS GeForce GTX 560 (Fermi) 1 GB 256-bit GDDR5

  GPU size: 9 "x 4.4"

  Power supply: Antec High Current Gamer HCG-750 750W Series

  "Power supply Dimensions: 7.1"x 5.9"x 3.4"

  I wonder if these prodcuts will enter the computer, as is or if I should look for other products.

  Thank you

  The ASUS GTX 560 should adapt and work very well. The Antec PSU is great and very likely to have problems in the space provided. It can interfere with connections to the motherboard and push against the CD/DVD discs. Please look at the Corsair CX600 instead. It is only slightly larger than the block of power SUPPLY HP stock and is known to adapt.

  Frank

• microSD on HP Pavilion Elite HPE - 590 t?

  I know that my HP Pavilion Elite HPE - 590t PC has a 15-in-1 memory card reader, but I try to understand what are the 15.  Can't seem to locate the list.

  Specifically, I'm trying to understand if it has microSD.  Anyone know?

  Hello

  Normally, it supports the following cards:

  • Compact Flash I

• USB ports do not respond after boot to Windows 7 - HP Pavilion Elite HPE

  I turned on a HP Pavilion Elite HPE this morning and none of the USB ports work under Windows 7.

  Mouse and USB keyboard work well in the BIOS Setup.  But after Windows starts, it is as if he found neither.

  I tried to start Windows in Safe Mode and last known good Configuration and the behavior is the same, the mouse and keyboard do not work even if they do it in the BIOS.

  I tried a different mouse and keyboard and Windows behavior is the same.

  Now, I would like to have active remote destop. Difficult to solve without an input device.

  I found a solution for Windows 7 x 64 failing to detect any USB device on all ports USB to a HP Pavilion Elite HPE-500f.

  After that backup, read and edit the registry remotely to run the utility of Microsoft Devcon registry run key, Devcon announce an error message 39 for USB hubs.  Enter 'Windows error 39 usb hub' in a search engine led me to the next web page that describes the resolution of the problem. I removed the UpperFilters also well described and restarted key and until then. -See more at: http://www.tricksguide.com/solve-device-manager-error-code-39-on-usb-controller.html

• Power for desktop Pavilion Elite HPE 550f.

  I want to know if the power supply for the Pavilion Elite HPE 550f active or passive PFC. the specs online say: 460 watts, PFC power adapter. I was not able to find whether it is active or passive.

  Thank you!

  Hello

  He is ACTIVE.  Delta made power supply HP 460 watt (Bordeaux). DPS 460 DB3 - A

  This article will give you an explanation of the difference between assets and liabilities.