HP Pavilion g4-2235dx Notebook PC stuck on auto repair for a month now... Please help...

so my laptop HP Pavilion g4-2235dx product number: C3Q50UA has been slain in automatic mode of repair for like a month now... it goes not far than this screen... the day it happened first I booted up & it real quickly flashed a blue screen that says my computer needs to reboot so itll restart itself for me then it rebooted & went to the screen hp for 10-15 minutes , then went to the automatic preparation of repair screen for about 2 hours, then the screen comes to have dark & remained like that all night... the next day I turned off the laptop & started again & it would be on the screen hp for a long time & id farm & turn on again, then he would start, restart itself then go to auto repair. If I stop it on the page of sutomatic repair then it would be just cranking up the hp screen & nothing else but if id shut down on the hp screen & turn it back on go to repair automatic page... back & suite back & rear returns & suite for days... Finally once a week or so, I gave up... i left on the page of auto repair for about 2 days directly plugged in so he would die just in case he might just need more time but 2 days was too long so I finally unplugged it & left on this page until the battery is dead & haven't touched since... Ive read some of the other posts on the loop of auto repair & what to do, but I don't want to lose all my stuff on the laptop as my images/videos(thought i saved them to skydrive but apparently i didn't complete the whole process to access my stuff from another windows 8 device)... I bought the used laptop & the warranty has already expired... any installation of windows 8 flash disk/drive. I have no recovery disk. so I have no way to replace my OS or recover my data that are already on this laptop... is there something I can do to get out of this dealie loop of auto repair without an installation/recovery disk/flash drive?

You'll need a Windows 8 rescue flashdisk, HP usb recovery media or disk recovery in order to access the safe mode and the Startup Repair. The cost of a recovery of HP USB is not that much to around $ 30.00 USD. You can also ask a friend or relative whose computer has the same BONE to make a recovery of Windows 8 key for you.

If you want to recover data from the hard disk before performing any repairs more, then you will need to remove the hard drive. You have the choice to start the installation in a usb enclosure, using a usb cable to power\sata or install temporarily to with a sata available on a desktop at home.

Tags: Notebooks

Similar Questions

  • Re: Satellite C855D-13N stuck on auto repair - recovery does not work

    Hi, guys

    My Toddler press the Start button and keep the key all the keys on the laptop before her start and was suddenly cut off and I try to restart again now is stuck on auto repair

    I forgot to create a recovery disc, so I order a Toshiba, and I received it yesterday starting from f12
    I did put the cd n ° 1 and keep saying missing files error

    here what it says on the laptop (TOSHIBA SATELLITE C855D-13N) 3 MONTHS

    * Your PC needs fixing *.
    * This operating system could not be loaded because a required file is missing or contains erreur.*
    *: file: fwpkclnt.sys*
    * error code: 0xc00000e9 *.

    * you will need to use the recovery on your amovible.* installation tools
    * If you do not have any media (such as a disc or USB device) contact your system administrator or the PC manufacturer *.

    * Press F8 for commissioning setting *.

    When I press F8 nothing happens

    Can someone help us out please
    Thank you

    Hello

    The message looks like the laptop will not boot the disc.

    The question is: is this a problem with the new recovery disks, or perhaps with Notepad

    To be honest, I think his recovery disk problem, and maybe you will need contact the drive vendor to replace the recovery media.

    But before that, try this:
    Switch on and press F2.
    Now you should be able to access the BIOS. Set the CD/DVD device in the first starting position here. Also, to clear the safe boot option from the UEFI CSM.
    Now to boot from the recovery disc.

    Would be interesting to know what is happening

  • Windows 8 is stuck on auto repair

    Hello

    My asus laptop Windows 8 is stuck on auto repair at startup. He would go to the blue screen with advanced with the refresh options, options restart.etc

    I want to restart my PC but I'm afraid that my Microsoft office will be removed from the laptop. He came with the bundle and was not preinstalled. I don't want to spend money on something that came with the real package.

    Can someone please tell me how I can go beyond the auto repair or restart without losing Microsoft Office and other program that comes with it.

    Many ways,

    Max fleet

    Hi again,

    We took the PC to PCWorld and the reason why it was a loop was because we are all off evil! We are just for Windows 8.1. Hope it will be more stable. Thank you very much for your help, I appreciate it a lot :D

  • Pavilion: I forgot my password BIOS administrator and get 'system disable' with '85379569' Please help me

    .

    Hello:

    Please read the first post on the link below for what to do with the system off (halt) code given by the PC.

    http://h30434.www3.HP.com/T5/notebook-operating-Sy...

  • Windows stuck on "auto repair loop."

    Currently the display of my Macbook (because it works).  My PC is stuck on the "automatic repair" cycle, I rebooted a million times, I restore to an earlier date and still nothing.  No fix for that with out having to reinstall?

    Hi Gareth,

    The ntoskrnl.exe file is a basic operating system file. If it is damaged or missing, you get this error.

    What is the brand and model of your computer?

    I suggest you to scan a drive for controlling the Windows recovery environment (WinRE) and check if it helps.

    Abbreviation for "check disk" CHKDSK is a system tool in Windows. He checks the integrity of a volume file system and correct the logical file system errors.

    Follow the steps below to run chkdsk WinRE analysis

    1. To start your computer, wait for the logo of the manufacturer to check the option of start menu, it will usually F12.
    2. The start menu key can be different with each manufacturer. If you are unable to find the start menu button, you can consult the user manual.
    3. Restart the computer, when you see the logo of the manufacturer, continue to press the Boot option menu key to enter the boot menu and change the option to boot in DVD ROM.
    4. After you start your computer by using Windows 8 DVD, a black screen appears with the gray text "press any key to boot from CD or DVD". Press a button on any.
    5. Select the type of keyboard and good time.
    6. Click on repair your computer in the lower left corner.
    7. Click Troubleshooting, advanced option, and then click command prompt
      Type the following command
      chkdsk /f /r and press enter on the keyboard

    Important: Running chkdsk on the drive if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data may be lost

    If the issue still persist after scan try to re - build BCD

    Follow the steps below to re - build BCD

    1. Go to the command prompt of the WinRE by steps above following and type commands below
    2. Type the following commands and press ENTER after each command line:
      Bootrec /fixmbr
      Bootrec /fixboot
      Bootrec /scanos
      Bootrec /rebuildbcd

    Restart the computer and check the issue.

    Post back with the result so that we can help you further

  • Why am I not able to update the latest version of Firefox when it tells me that it is ready to download. It seems "stuck" on the connection to the update server and goes no further. This happens everytime I try for several months now.

    I think that the version he is trying to download is 10.something, and it seems to freeze on the window of 'progress' for quite awhile before I get it close. I've sometimes minimized the window while I did other things, coming to him perhaps 30 minutes later and the window is exactly the same as when I left it.

    You can try the alternative and easier way by downloading from here

  • HP Envy m6-k010dx: update Windows 10, recently received message OS not found, stuck in auto repair

    Recently updated to Windows 10 8.1 and everything was fine, but then I started affected by Frost (windows stopped responding and the mouse and keyboard and I couldn't get to the Manager of the tasks accordingly) sometimes the gel would solve itself, but more often than not a closed hard must be carried out. Fast forward to today, and my computer froze 5 + at a time or two hours, then I close it and let it sit for a few hours, because I had to leave in any case. When I turned it on back but can't find OS message not shown on the screen and the computer turns off. I turned it on the message before auto repair, who showed up for a minute or two and then goes to a black screen and stays there, no options provided (I've ever seen the screen which offers the possibility to fix computer or solve the problems I found among other positions) and this has been the case all day no matter how I try to start it. A further experimentation I managed to get Hardware Diagnostics UEFI test using F2 (checking the battery, check processor, check for the wireless module, check the system board and the SMART hard disk check were in seconds, as soon as he started on short Hard Drive DST check that I received the result of the FAILURE and the test fails also) the results displayed as follows:

    ID 90F439-6MP7RE-XD7WXG-60QJ03 failure

    Product IF: E0L01UA #ABA

    Hard drive 1

    Do I have to replace the hard drive? Of course if this isn't the case any other ideas would be appreciated particularly with regard to the possible explanations about what could have caused this since I have not had any problems with the computer before the upgrade and no damage had never place and best way to proceed.

    Update: before posting this I turned on the computer and received the HP normal logo displayed during startup, after waiting a few minutes however the dreaded blue screen appears and displays the message saying:

    your PC must be rebooted, it will restart for you in a few moments...

    Then below this additional information concerns the following text is displayed:

    SYSTEM_THREAD_EXCEPTION_NOT_HANDLED

    and then of course the computer shuts down. The computer was then turned and saw the preparation of auto repair as before (I had never received this precondition of message blue screen). So even once any idea would be appreciated, I think I've covered most of the details, but if anything else would be helpful let me know.

    @SabrinaRM: sorry to say this, but the drive test result means that your drive is defective or has already failed - and needs to be replaced. This means that no recovery, automatic or not, will work as the recovery information are damaged on the drive.

    Once you have a new drive, you must restore your PC - but that is a problem.

    Normally, I advise to use HP recovery media to restore your PC to its original state, but, unfortunately, there is only no recovery media HP not related to HP for your PC Product Page.  You can try to contact the HP customer directly, using the links below, to see if you can order them if:

    If you live in the United States or the Canada, details are on this page: http://www8.hp.com/us/en/contact-hp/phone-assist.html#section1

    If you live elsewhere, contact details are on this page: http://www8.hp.com/us/en/contact-hp/ww-contact-us.html

    If HP no longer provides a recovery media for your model, a few other sites, you can check are: http://www.computersurgeons.com/Default.aspx and http://www.restoredisks.com/

    Good luck

  • Microsoft Blackboard - I'm stuck at level 24... can someone please help!

    Remember - this is a public forum so never post private information such as numbers of mail or telephone!

    Ideas:

    • You have problems with programs
    • Error messages
    • Recent changes to your computer
    • What you have already tried to solve the problem

    Hello

    You can search the Blackboard online game walkthroughs. A procedure is a guide that will teach you how to finish the levels of a
    particular game. Search using your search engine preferred for more information.

    You can also post the question in the games for windows support Forums.
    http://forums.gamesforwindows.com/

    Additional information:
    http://Windows.Microsoft.com/en-AU/Windows7/touch-Pack-how-to-play-Microsoft-Blackboard

    Kind regards
    Afzal Taher-Microsoft Support.
    Visit our Microsoft answers feedback Forum and let us know what you think.

  • Stuck in "Startup Repair" for more than 24 hours. How to get back to normal?

    Accidentally disconnected my external hard drive (my passport western digital), without disconnecting properly.  After that I connected again, with the power still on it, it asked me password of my external hard drive.  Once I entered the password as the frozen screen.  I manually turned off the laptop (sony vaio, nearly 2 years, vista pre-installed), then power.   He asks me to choose the startup repair or start normally.  I chose startup repair, need me a green-bluish screen with a blue loading bar.  Constantly load bar (move to the right on several occasions).  I let this one day and a half!  Nothing.  Off by pressing the power button.  Also, I unplugged the external hard drive thinking that was the cause of the problem.  No devices are connected to the laptop now. Power turned under.  Yet once, a black screen with text asking me to choose at startup repair or start normally.  This time I try to boot normally.  The screen is white and black for a few minutes, then an arrow cursor appears for a couple minutes, and then he brings me right to the Startup Repair choose or start normally.

    I also need to say that any action is veeeeeeeery slow.  It takes minutes just to get from one screen to the other.

    I actually pulled that momentarily to a screen with a gray window that reads "system recovery options choose a tool" with the following choices: «Startup Repair, System Restore, restore full pc windows, command prompt, windows memory diagnostic tool»  That return me to normal or the other.  Turned power off and then on again and I tried pressing F8 at startup upward.  It gives a long list of options of safe mode, etc.  I am at a loss.

    Every action I take, I find myself back to choose the Startup Repair tool or start normally.  Nothing works.  There is no way, that everything is just gone!  I didn't disconnect an external hard drive accidentally!

    Please help if possible.  Tomorrow will be the day 3 of this madness maddening, ridiculous.

    Well, it's a week or so later, here is what happened: the hard drive was dead along... Well well... According to the pc repair shop I ended up taking to.  That is why no troubleshooting worked.

    So THANKS to those who have tried to help me, but it was ultimately useless in the end.

    Computers are too sensitive if you ask me.  Certainly did not get my money's worth out of it.

  • I'm stuck in safe mode for the month.

    I can't get out of safe mode. When I reboot, I have to choose to be in safe mode. If choose not to go in safe mode, my screen becomes white.

    Hello

    We are here to help. To exit safe mode, please follow these steps posted by A.User.

    Keep us informed.

    Kind regards.

  • Computer Dell help is stuck on Auto Repair preparation

    Is there an easy solution to this without moving, downloading my files?

    I read what one guy said to move to Windows 10, but it's the same that destroy all your backup files and documents.

    I'm ready to save everything on the command line, if I

    Hello

    Follow these steps in troubleshooting Dell:

    "Computer does not start in Microsoft Windows 8 or 8.1"

    http://www.Dell.com/support/article/us/en/19/SLN115652/en

    Table of contents:

    1. Specific issues Windows 8 any boot
    2. Check that the computer finishes powering (POST)
    3. Repair your operating system of Windows 8
    4. Search for specific error Messages
    5. Run a computer Diagnostic
    6. Rest the BIOS to default values
    7. Disconnect any external devices
    8. Virus and Malware troubleshooting
    9. Restore the operating system to factory settings

    "Dell diagnostic tools can I use to solve hardware problems?

    http://www.Dell.com/support/article/us/en/19/SLN114988/en

    "Resolve using issues material ePSA or diagnostic PSA and Guide to Error Codes"

    http://www.Dell.com/support/article/us/en/19/SLN133583/en

    See you soon.

  • Stuck in auto repair

    Missions on the Web site, many users seem to have the same problem, but have not seen a response that resolves completely.

    When switch on laptop ACER will repair auto and scan drive c, and then blue screen below shows with:

    error try again

    Press F8 to go to start settings

    Press ESC for UEFI firmware setting

    When select F8 sometimes, it will however a loop on the right and returns to the highest. On some occasions comes up with a screen with a number of options, including selecting Safe Mode 4.  When select is not safe mode, but reboots back in auto repair and loop back as above.

    Have a USB key with the installation of origin, but when it connects to the laptop and start upward does not recognize.

    Can you advise how to go in safe mode in order to restore to an earlier point (preferable) or allow accessible USB from beginning to the top so can put laptop back to factory settings. In response, please consider who are unable to enter other commands at the moment all other screens.

    Concerning

    Andrew

    Hi André,.

    Thank you for the update on the issue.

    If still you remain blocked on the loop of repair then I suggest you to contact the manufacturer of the computer and see if they can solve the problem or can better provide you with the troubleshooting steps.

    Keep us updated on the issue.

    Kind regards

  • HP Pavilion g6-2260us Notebook PC

    Hello...

    I need a network driver for my HP Pavilion g6-2260us Notebook PC.   I would use win7 (32 bit) now, so this would be a dirver which would be compatible.

    Please help me.   I do not understand win8

    Shawn

    Hello:

    Download and install the second pilot on the list at the link below...

    http://www.Realtek.com.tw/downloads/downloadsView.aspx?langid=1&PNid=14&PFID=7&level=5&Conn=4&DownTypeID=3&GETDOWN=false

  • How to enable bluetooth in my HP Pavilion g6 series Notebook?

    I have HP Pavilion g6 series Notebook and am trying to pair it with a bluetooth device.

    I can connect to the device via my iPhone well.

    Problem is that I don't know if my laptop supports bluetooth,

    and if so how to activate it.

    I went to control Panel\Hardware and the Sound\Devices and printers and tried to add a device - not good.

    I tried to search it upward in networks - not good.

    would appreciate your help!

    Bluetooth is not usually found in laptops the lower price point.

  • HP Pavilion n242se-15 Notebook PC with win 7

    I have HP Pavilion n242se 15 Notebook PC with window 7 and he is there in no display driver, ethernet and many others

    where can I get this laptop driver for window 7

    expert please help me.

    There are hardware ID missing drivers

    Bluetooth controller

    PCI\VEN_1814 & DEV_3298 & SUBSYS_18EC103C & REV_00
    PCI\VEN_1814 & DEV_3298 & SUBSYS_18EC103C
    PCI\VEN_1814 & DEV_3298 & CC_0D1100
    PCI\VEN_1814 & DEV_3298 & CC_0D11

    Ethernet controller

    PCI\VEN_10EC & DEV_8136 & SUBSYS_2166103C & REV_08
    PCI\VEN_10EC & DEV_8136 & SUBSYS_2166103C
    PCI\VEN_10EC & DEV_8136 & CC_020000
    PCI\VEN_10EC & DEV_8136 & CC_0200

    3D video controller

    PCI\VEN_10DE & DEV_1292 & SUBSYS_2166103C & REV_A1
    PCI\VEN_10DE & DEV_1292 & SUBSYS_2166103C
    PCI\VEN_10DE & DEV_1292 & CC_030200
    PCI\VEN_10DE & DEV_1292 & CC_0302

    PCI device

    PCI\VEN_10EC & DEV_5227 & SUBSYS_2166103C & REV_01
    PCI\VEN_10EC & DEV_5227 & SUBSYS_2166103C
    PCI\VEN_10EC & DEV_5227 & CC_FF0000
    PCI\VEN_10EC & DEV_5227 & CC_FF00

    PCI Simple communication controller

    PCI\VEN_8086 & DEV_9C3A & SUBSYS_2166103C & REV_04
    PCI\VEN_8086 & DEV_9C3A & SUBSYS_2166103C
    PCI\VEN_8086 & DEV_9C3A & CC_078000
    PCI\VEN_8086 & DEV_9C3A & CC_0780

    Bus Controller SM

    PCI\VEN_8086 & DEV_9C22 & SUBSYS_2166103C & REV_04
    PCI\VEN_8086 & DEV_9C22 & SUBSYS_2166103C
    PCI\VEN_8086 & DEV_9C22 & CC_0C0500
    PCI\VEN_8086 & DEV_9C22 & CC_0C05

    USB controller

    PCI\VEN_8086 & DEV_9C31 & SUBSYS_2166103C & REV_04
    PCI\VEN_8086 & DEV_9C31 & SUBSYS_2166103C
    PCI\VEN_8086 & DEV_9C31 & CC_0C0330
    PCI\VEN_8086 & DEV_9C31 & CC_0C03

    unknow device

    ACPI\HPQ6007
    * HPQ6007

    Hello:

    Use the W7 x 64 drivers from 15 t-j100 except the graphics card intel and the realtek audio.

    DO NOT USE ALL DOWNLOADS OF BIOS OR FIRMWARE OF THIS MODEL

    http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?OS=4063 & LC = on & CC = US & DLC = in & sw_lang = & Product = 6521374

    Now, here's what you need to do to install the graphics...

    First install the model Intel chipset driver and restart.

    Then, install the Intel HD graphics driver and reboot.

    https://Downloadcenter.Intel.com/Detail_Desc.aspx?AGR=Y & DwnldID = 23714 & lang = eng & OSVersion = Windows % 207% 20 (64-bit) * & DownloadType = 0a % 09% 09% 09% 09% 09% 09% 09Drivers % 0 a 09 09% 09% 09% 09% 09

    Then install this model Nvidia graphic driver and restart.

    Audio: Accept the agreement, download and install the driver for the second on the list.

    http://www.Realtek.com.tw/downloads/downloadsView.aspx?langid=1 & PNid = 24 & PFid = 24 & Level = 4 & Conn = 3 & DownTypeID = 3 & getdown = false

    You want the Ralink drivers for wireless and bluetooth.

Maybe you are looking for