HP Pavilion G6-1d08dx: cannot order the recovery kit

Similar Questions

• Satellite A110: Cannot order the recovery disk - where to get a

  After some problems with a virus, I need to restart the system.
  I tried with the Windows operating system from another computer, but the internet does not work, I can't ' install the drivers of wright.

  Where can I buy the recovery disk? Toshiba support replied, they do not have it because the computer is too old (2006). Maybe someone can send me the recovery disk?

  Help, please

  Hello

  I guess that you have contacted the ASP in your country, and they said that the recovery disc can be pronounced, because it is no longer available.

  Well my friend, this is bad news... seems you can not order.
  In this case, you will need to install the OS by using the Microsoft Windows disk and then you can download all the drivers from the page of European driver Toshiba Toshiba.

  Good bye

• Pavilion g series: cannot access the recovery partition & disk do not work

  Try to reset the computer to factory since it does not start in Windows.

  When I try to enter in recovery "esc then F11" it will just try to load windows. Recovery partition is still there just can't access.

  So I try to use disc 5 figure set I did 3 years ago & it starts on the 1st cd, but I get a message saying that the disk is not for this computer.

  I'm like what?  This computer rendered & I have the best recollection no changes to anything that should have caused the recovery to think that there is another computer.

  Suggestions on what I might have to do in order to recover my computer to the factory?

  How can I access the partition recovery from normal mode does not work?

  Why the hell does not work my cd?

  I bought the computer again.

  Any help would be greatly appreciated.

  onelunger wrote:

  Thanks for the suggestion, but I can't return to Windows, even in safe mode.

  If this is the case, then you need the recovery media you can perform a factory image recovery.

  You can remove the hard drive and connect it to another PC through an external drive enclosure or a usb cable to sata. Which will allow you to copy your important data from the drive to another device of storage for extra security.

• Cannot order the recovery disk

  Hi, for more than 12 hours I can't order discs using this site: https://backupmedia.toshiba.eu/landing.aspx

  When I'm trying to confirm my number series or something, he always says: Unfortunately, the review of the serial number is not possible at the moment. Please, try once more later.

  Please help me with it,

  Concerning

  And how to help?
  Don't you think that anyone here has influence on the business of Toshiba?

  There may be a technical problem with the page.
  Try again tomorrow or Monday.

  Moreover, what model of laptop do you have?
  You have an older model?

• Satellite M70: Where to order the recovery disks?

  Anyone know where I can download or order the recovery disc for my M70, the place, I took it to get fixed has said that it cannot be repaired without them.

  Hello Luke

  Your M70 does not come with recovery DVDs? As far as I know, it certainly comes with recovery DVDs and application please your local dealer on the subject.

  The recovery image can not be downloaded only ordered by the Toshiba authorized service partner in your country.

• Satellite A30 - where and how to order the recovery disk

  Hello

  I have a Satellite A30 range and I'm about to install a new hard drive but I don't have the original recovery disk. I told myself I can are no longer met this Toshiba directly so I wonder if someone can direct me looking for a replacement of original or copy.

  I Googled it but it is difficult to sift through to find the exact one I'm looking for.

  Thank you

  Hmm. I thought you can order the recovery CD Toshiba of the ASP in your country but if the series of laptop it is too old it would not be possible.

  However, you can also install the Windows operating system by using the Microsoft CD and then you could install the driver of Toshiba of the Toshiba driver page.
  XP driver should be placed in the box ARCHVE.

  * Archive *-> Satellite-> Satellite one-> Satellite A30-> Win XP

  welcome them

• M6-1035dx Pavilion: clone SSD drive cannot locate the recovery Partition

  I recently bought a HD 500 GB of SSD to replace the original that came with the laptop.  The SSD drive I bought is slightly smaller than the original one.   I used the cloning software is Macrium.  Partitions, I am interested in cloning are the HPTools and recovery.  Stand have been cloned successfully by the software.  I put the active recovery as well.

  After swapping the drives, the system starts the HPTools immediately, but the options for the restoration part are "grayed out".  I can't access it.  I tried several times, and this is where I am stuck.  It seems that the recovery partition is not detected by the cloned HPTools.

  I do not have the recovery DVD, but I have the original HD with partitions intact and they work just fine because I recently test the recovery process.

  I missed well to clone the original HD somehow that the SSD is unable to detect the partition?  Maybe I missed a step?  The difference in the size of the hard drive causes a problem in the recovery process?  How can I remedy the situation and use my new SSD?

  Thank you for all your advice.

  Try the complete sector-by-sector disk cloning.  If you use Macrium, you will need a paid version. The free version just do enough for the advanced cloning procedure you need.  See the following web document to compare versions.

  http://www.Macrium.com/reflectfree.aspx

  BTW, an SSD detects nothing. This is the BIOS and the operating system that detects hardware, firmware and software.

  You can use HP recovery media successfully on an SSD or not, that has at least 160 GB of capacity. Your 500 GB SSD certainly has enough capacity.

• Windows recovery system cannot read the recovery disk

  I have Vista laptop computer model pavilion POS, when I bought it, I made a creation of recovery disks, but now when I put it in my PC to see contains I see an error that Sandra insert your disc and system cannot fix it and I also used microsoft fixed it Center but cannot fix it.

  Hello

  Here are all the HP information on different methods to recover back to factory settings

  Three ways to recover the PC to original operating status

  You have a choice of three ways to run a recovery and restore your computer to its original state. The recovery process may take an hour upwards or more and is not complete until the prompt to connect to the computer. When the recovery is complete, don't forget to run the update of Microsoft Windows and the HP health check to install all the drivers updated and software.
  1. If the computer can boot to the Windows desktop, start the Recovery Manager.
  2. At startup, press f11 to start Recovery Manager.
  3. Restore the PC to its original state with the HP Recovery Manager of in Windows Vista
     If the PC can be started and opens on the Windows desktop, you can use the HP recovery disk to restore the PC to original factory State by following the steps below.
     1. Click Start and enter the recovery in the field of research. Select Recovery Manager in the list, when it becomes available. Allow the action to proceed, if you are prompted. The HP Recovery Manager opens.
        Alternatively, click Start , all programs , Recovery Manager , and then Recovery Manager . Allow the action to proceed, if you are prompted. The HP Recovery Manager opens.
     2. Click Advanced options , System Recovery , and then click Next . The PC will restart and reopen the Recovery Manager.
        Alternatively, if the advanced options is disabled, click Next , and then System Recovery . The PC will restart.
     3. When the PC restarts, select the System Recovery option and click Next .
     4. If you are prompted to use the Microsoft System Restore , click No and then click Next .
     5. When you are prompted, select back up your files first (recommended) , and then click Next . Follow the on-screen instructions.
     6. When you are prompted to recover without backing up your files , please STOP before you click Next .

        CAUTION:

        It's the last chance to change your mind recovery PC and delete all the files and programs. Once you click Next , the restore process cannot be stopped

     7. If you are convinced that you want to start the recovery process, click Next . The PC immediately starts formatting the disk hard drive and destroy all data.
     The recovery process may take up to several hours and will return the PC to its original state. All custom, settings drivers, software and upgrades or hardware updates are lost and must be reinstalled.
     Restore the PC to its original state with the HP Recovery Manager if Windows Vista is not accessible

     If the PC does not start under Windows, it may still be possible to use the HP recovery disk to restore the computer to its original state. The Recovery Manager can be started during the boot process by following the steps below.

     1. Press on the button / stop to start the PC and press the f11 key when the standard BIOS guests appear on the black screen.

        NOTE:

        By pressing the f11 key at startup on a computer with an image factory HP will start the system recovery process, even if the message is not displayed.

        • If the HP Recovery Manager can access the hard disk recovery partition, a prompt to back up user files before you start the recovery
     . Follow the instructions.
     • If the HP Recovery Manager cannot access the hard disk to resolve system errors, you need to use the recovery disk custom that you created to recover the hard disk to its original state.
     • If you have not created the custom recovery disk, or disks are damaged, you can order a replacement of HP recovery CD.

  4. When the Recovery Manager starts, follow the instructions of recovery step by step , shown above.
  Solve a common problem of recovery.
  If the original operating system is changed to a non - Vista OS, the Recovery Manager cannot be launched either office or by pressing f11 at startup. You can use the recovery disk to restore the computer to the original state of Vista. If you are using a non - Vista OS, you can use a third-party partition management program to recover hard disk space.
  Restore the PC to its original state with the recovery discs

  If the PC cannot access the Windows desktop, and the Recovery Manager cannot be started by selecting the f11 at startup key, you can use either the recovery disc custom that you created, or you can order a recovery CD to replace HP, to boot the PC and restore the hard drive to its original operating state.

  NOTE:

  Run the recovery process by using the custom recovery disk you created can take less than an hour, while you use replacement discs ordered directly from HP can take four to six hours and includes several reboots.

  If the HP Recovery Disk Manager can access the hard drive, it will attempt to repair the recovery partition. If successful, a prompt to continue execution of the recovery using the Recovery Disk Manager.

  Use the recovery discs to restore the PC by following the steps below.

  1. Insert the recovery disc into the optical disc drive and start the computer.
     If the computer is running, insert the reinstallation disc and immediately click on Start and select restart to force the computer to boot from the recovery disc.
  2. When prompted, Press any key to boot from the CD or DVD, press any key on the keyboard.
  3. Leave the recovery disk boot and load the files required, while the Microsoft loading screen appears. It may take several minutes to load the required files.
  4. When the HP Recovery Manager window appears, click Advanced options , System Recovery , and then click Next to open the Recovery Manager.
  5. Follow the on-screen instructions and perform the necessary actions.

     NOTE:

     Do not interrupt the recovery process even though the computer may restart, and the Windows desktop can display at different times.

  • When you are prompted, follow the on-screen instructions to backup user files.
  • After completing the backup, when you are prompted, reinsert the recovery disk, and then click Next to continue the recovery process.
    A status box is displayed to indicate the State of the recovery and the estimated remaining time.
  • If you have used several disks when you created the custom recovery discs, follow the prompts to remove the first disc and insert requested discs.
  5. When you are prompted to Insert additional driver disk , take one of the following actions:
     • If you purchased a replacement of HP recovery disk and it included an extra driver disc, insert the disc, and then click OK or Next . The recovery program checks the additional drive and installs the necessary files.
       After you install the additional files, a prompt to remove extra disc and insert the original recovery disk.

     • If you bought a replacement at HP recovery disc, and he didn't get an extra driver disk, click ignore or Cancel . The recovery program will ignore the request and install the following file on the recovery disk.

     • If you have created a personal recovery disc, press Next to continue.

  6. Continue following the onscreen instructions to complete the recovery process.

  NOTE:

  If you have not created a personal recovery disk or the recovery disk will fail or corrupt, see HP - order recovery discs for Windows 7, Vista or XP laptops for more information.

  7. hard disk crash (intelligent control error 0303) cannot use the recovery

     I have a hp pavilion dv6-6050 and it crashed suddenly I can't use recovery option, because it cannot read hard drive

     I tried to connect the hard drive to another pc via sata-usb cable and the other pc has detected hard disk read errors

     How do I return the recovery partion so I can use it on a new hard drive

     Hello:

     You will not be able to.  When the disc is dead, it took the recovery with her partition.

     You will need to order a set of recovery discs, and they can only be used if you buy a hard drive of the same size or more large storage capacity than the one who died on you.

  8. How to order the recovery for my Satellite A660-149 disk?

     I'm trying to drive recovery order for my A660-149 of the https://support.toshiba.com/support/serviceUnitVerification?orderType=SFF
     But it says my series or my part is not valid. I know that this model is old enough, but I can't find anything about it on the Toshiba site.

     I really really need this recovery disk.

     Have you been to wrong side. For European models for laptop, you cannot use US assistance page.

     Please visit https://backupmedia.toshiba.eu/landing.aspx
     There, I hope that you can order the original disc of recovery for your laptop model.

  9. HP Pavilion Notebook g7: Re-create the recovery on D drive partition

     I have a HP Pavilion g7, which originally had Windows 7.  I recently upgraded to Windows 10. However, the recovery partition (D has still the Windows 7)  Question: Can I just remove the Windows 7 file and re-create the partition recovery with Windows 10 or is it more involved.

     morris81

     Basically, the answer is no.

     Why?

     Because installed HP recovery Partition contains a custom Windows OEM compressed HP image and the firmware on the same PC is written to be able to start in this partition (using F11) to this recovery.

     Your own partition does NOT contain this file because there is no way to get at HP.

     Even in this case, the F11 process wouldn't work, even if you haven't created your own partition.

     However... If you want the means to do a full system recovery, then consider using a third-party product known as Macrium Reflect the image of the installation.

     Macrium reflect (MR) provides a FREE version that can be used to image and restore partitions or drives together.
     
     What I recommend is the following:
     (1) download and install Macrium reflect (MR)
     (2) run M. and choose the option: "Create an image of the partition (s) required to backup and restore Windows" to write a full backup to an external drive or USB key
     (3) use the option to create a CD or a USB startup key
     
     My experience is that SIR, when you use the option of Compression high, typically allows to compress the image file recorded at about 50% of the space USED in the OS partition.  This means that if you have a 40GB and 80GB OS partition is used, MR must only about 20 GB to store the image file.
     
     I use all the time and it usually takes less than 10 minutes to make the backup of the image and at the same time or less do a restore.

     In addition, MR has the ability to add a recovery Boot Menu entry.  This then allows you to boot into Windows re, and then you can use it to do a restore - when you cannot start Windows!
     
     NOW, you have the means to restore a full system that works for the external hard drive or USB key in a few minutes.

     Good luck
     ========================================================================
     I'm a volunteer and I do not work for, or represent, HP.
     ---------------------------------------------------------------
     If my post helped you, please click on the Thumbs-Up symbol on my post to say thank you.
     If my posts resolved your issue please click "accept as a Solution.
     ========================================================================

  10. Equium L20 - cannot complete the recovery procedure - disk error

      Hello

      I have a laptop Equium L20 and whats happened is, during a recovery of product, he gets to 25% then emits an error at me and stops working.

      Now when I turn on the laptop, I get the Toshiba screen, then nothing.
      I was informed that my drive is probably broken and I now no operating system but I am a complete computer novice so don't know how it is.

      I took the laptop to PC world a few years ago and they run a recovery of product but I did not my drive, so I want to know is, is it possible to run recovery without the disc?
      (seems to me just don't forget the sound by pressing a few buttons)

      If so, how?
      And if not what someone have any suggestions as to how I can restore the computer?

      Thanks in advance

      Hello

      > during a recovery of product, sometimes about 25% then emits an error at me and stops working.

      As you mentioned, possibly recovery disk is defective, broken, or similar, this could be the reason why the CD/DVD drive is not able to read the disc and the installation breaks upward.

      You cannot get this phone without the recovery disk! It is an old series laptop and it does not support the HARD drive recovery process, as do other mobile most recent.

      If you have only two ways to install the Windows operating system; you need to use the Toshiba recovery disc (which seems to be broken) or you can install the operating system by using the Microsoft Windows XP disk.

      If install you the operating system using the disk of MS original then you need to install the drivers of Toshiba which are placed on the European driver Toshiba page (look in the archives).

      PS: maybe you could try to burn (copy) the recovery disk using another computer.
      In some cases of the different drives are able to read scratched discs.
      If you want to be successful and if you want to be able to copy the recovery disk, you can then use the new disk in order to restore the operating system on your computer satellite phone.

  11. Order the recovery disks for Windows 7 64 bit

      Hello.

      I have trouble finding the recovery media to order on the list of downloads. I have a HP Pavilion DV6-6030ew.

      Thank you

      Hello

      Contact HP and order them directly - the telephone number can be found on the corresponding link below.  Have details such as your model number. and serial number. hand during the call.

      If you live in the United States, contact HP here.

      If you are in another part of the world, begin here.

      Kind regards

      DP - K

  12. Pavilion 15-r004ne: cannot adjust the brightness of the display

      I m using the Pavilion 15-r004ne on a windows 64-bit OS 8.1 and I cannot adjust the brightness of my screen. I tried to adjust by shortcut keys F2 and F3, tried adjusting via the mobility Center, tried through Control Panel and so on, but no response until now. It shows the little pop-up when I press the keys. But nothing has changed, the brightness of the display remains the same. in order to get solution soon.

      Thank you for your support. It didn't work either. I solved the problem of roll back the driver and update again.

  13. Cannot start the Recovery Console Windows from the installation CD

      On my MacBook I ve running in VMware Fusion 3.0.1 a Virtual Machine with Win XP Pro.

      When I reboot Win XP Pro and start again from the Windows XP Pro installation CD, I can see the "Welcome" with the menu screen

      -To install Win XP now, press ENTER

      -To repair an installation of Windows XP using the Recovery Console, press r.

      -To quit Setup without installing Windows XP, press F3.

      When I click ENTER or R, I see the message

      -The installation program did not find any hard drives installed in your computer. Setup cannot continue. To quit Setup, press F3.

      Today the question? In the 40 GB of the virtual machine, I have two free partitions of 10 GB and 20 GB Win XP Pro execution. Why see Setup cannot process this partition?

      I ve also installed a second Virtual Machine, but the installation of VMware Fusion not show the "Welcome" screen, but it installs both Win XP Pro.

      The installation of the recovery in the virtual race Machine Win XP Pro Console is successful, but when I start the recovery in Start Menu Console, just the screen blue 0x7B (inaccessible boot device).

      What must I do, to start the Recovery Console in VMware Fusion? Or another question: when merging does support the Windows Recovery Console?

      Wow, nothing indicates that you use a German version of Fusion that your English is excellent.  Anyway as VMware headquarters is in the United States, like me, I always provide information in English and information-specific guidelines in the VMware Fusion help files come from the English version as well as any Documentation from VMware that I reference.  I say this next part as a general and not directed comment towards you, as you have noted your using the German version... Any person requesting help must always at least include technical information referencing manufacture, make, model, version, and language other then English, material goods and software involved in issues.  We'll find a good reference for the type of information that must always be included in HOWTO: ask (and answer) Questions.

      As a much get into the BIOS if you use the Fusion 3, you don't need to enter the BIOS to change the boot device as this can be done in the settings now however to enter the BIOS for other things that need/want of press you F2 directly after starting the Virtual Machine and after having clicked on the screen but the av VM boot so fast that it's easily missed.  You can add the following settings to the file of configuration .vmx of the Virtual Machine to slow down the startup so that force once in the BIOS.

      bios.bootDelay = "3000"
      bios.forceSetupOnce = "TRUE"
      

      The bios.bootDelay is in milliseconds and the bios.forceSetupOnce Boolean value is then set to FALSE, automatically.  Each of these parameters are independent of each other.

      You can find the following useful notes for this and or other uses...

      ====================

      Notes: keyboard

      Different setting function, you may need to adjust various preferences keyboard to work with the function keys and or use the Fn key.

      OS X > you may need to press the Fn + F6 etc. and this can be changed in system preferences > keyboard & mouse > keyboard > use all F1, F2, etc...

      Merger 1 > VMware Fusion (menu) > Preferences... > keyboard and mouse > activate Mac OS shortcuts keyboard

      Fusion of the 2 and 3 > VMware Fusion (menu) > Preferences... > keyboard & mouse > Mac OS shortcuts > activate Mac OS keyboard shortcuts

      ====================

      Notes: Starting the virtual machine from CD/DVD or ISO Image

      If the Virtual Machine is not initiating the CD/DVD or ISO Image, and then select the CD-ROM in the Boot Menu.

      Engage the Boot Menu and select the CD-ROM drive...

      The bottom of the virtual machine just above the status bar after the Virtual Machine is started, it has...

      "Press F2 to enter SETUP, F12 for the start-up network, ESC for Boot Menu"

      On the status bar, it features...

      'To direct entry to this virtual machine, click inside the window.'

      BIOS flashing by is very fast so you need to work quickly however give it a try and if the Start Menu cannot be higher then the configuration of the Virtual Machine file .vmx must be edited to slow the STATION and or change the boot order.

      OK, click the big Play button on the screen of the virtual machine, and then quickly mouse click in the Virtual Machine screen and then press the ESC key to bring up the Start Menu and select the CD-ROM drive. If it boots the CD very well and if the Boot Menu does not appear, because he goes just to quick access and then try again or...

      Watch the Boot Delay section in the current user's Guide to VMware Fusion and the section of the virtual machine files of A Beginner's Guide to VMware Fusion on when the configuration of the Virtual Machine's .vmx file is and add the following lines to the file. TextEdit can be used to edit the .vmx file.

      To give more time to indulge, the Start Menu Add the following...

      bios.bootDelay = "3000".

      For, once, force the VM in the BIOS to change the Boot order in the BIOS if the CD-ROM is first add the following...

      bios.forceSetupOnce = 'TRUE '.

      ====================

      Notes: By modifying the .vmx file

      For Fusion 2.x and 3.x ctrl-click the target entry of Virtual Machine on the windows of the library of the Virtual Machine and choose Show in Finder and then Ctrl-click on the packaging of the Virtual Machine and select to display the contents of the package.

      By default in the normal Fusion 1.x virtual Fusion function file are created in the folder "~/Documents/Virtual Machines" and according to host operating system version and or Fusion worm. There may be a .localized after Virtual Machines although by default, this extension is not visible in the Finder.

      ~ Is your Home Directory.

      The files that make up the virtual machine are placed in a folder (aka Bundle and or packing) bearing the extension '.vmwarevm' which, by default, this extension is not visible in the Finder.

      Example: "~/Documents/Virtual XP.vmwarevm Machines/Windows" in the Finder would just resemble an icon named "Windows XP."

      To view the contents of the entire file "Windows XP.vmwarevm" ctrl-click (or right-click) on the "Windows XP" icon and select Show the contents of the package.

      To change the configuration file of .vmx ctrl-click (or right-click) on the "Windows XP.vmx" file and select open with > choose another... then in Application choose TextEdit.

      Note: If you use Firefox do not copy and paste the parameters if TextEdit unless you copy only the exact line and nothing else in the case, use an editor such as TextWrangler.

      ====================

      Notes: Creating an ISO Image of the CD/DVD drive

      When you use utility disk in order to have a bootable ISO Image, you must select Master CD/DVD without encryption in which case by default, it will have an extension .cdr file and in version 1.1 of the merger and later does not need to be changed in .iso, although one can if one chooses to. A default .dmg image is compressed and is not bootable, as an uncompressed .dmg will start if changed in .iso and of course the source CD/DVD should be bootable in the first place.

      To create an ISO Image using disk utility...

      1 insert the CD or DVD disc into the optical drive of your computer.

      2. open disk utility (/ Applications/Utilities/Disk utility).

      3. Select the CD or DVD drive in the list of disks and volumes.

      4. Choose file > new > "Disk Image from (name of the disc)."

      5. type a name for the disk image.

      6. choose "DVD/CD master" from the Image Format pop-up menu.

      7 choose "none" from the encryption pop-up menu.

      8. click on save.