HP Proliant Gen8 DL380e not charge controller B320i with VMWare ESXi 5.0 U3

Similar Questions

• Plugged in, not charging on 6% with windows 7 ultimate

  Hello everyone

  Hi have the same problem with the guys here.

  I have a laptop Acer Aspire 5738 G with windows ultimate 7 installed.

  I tried all the tricks on the forum as stop the computer, remove the battery, remove AC power, hold on the power button for 10-20 sec and replacement battery and does not work for me.

  The message is 6% available (plugged in, not supported)

  If I remove the ac computer automatically stop as if was a blackout... as if my battery wasn't there.

  I tried the trick on this page, but does not work for me.

  http://social.answers.Microsoft.com/forums/en-us/w7performance/thread/d338d4c6-865a-49a3-8333-8c30e989a4f8

  Is there any solution for this?

  Thank you

  The battery compartment is broken I had it before on an acer laptop and I rang acer support and they put in the new housing of the battery and it worked.

  They said that a sector in the slot was broken.

• Could not find the device with uuid - ESXi 4 and 5 - Dell 2950

  Hello

  I am installing ESXi4 or 5 on a Dell 2950.  I'm not an expert material guy, but I think the controller is a Perc 5 controller hardware / i.  It is a processor of Intel Xeon dual core CPU 2.

  The link of compatibility:

  http://www.VMware.com/resources/compatibility/search.php

  I see only the processors Xeon 5xxx and above seem to be supported, and I honestly don't know if mine it fits or not but when I had installed CentOS and made ' less/proc/cpuinfo', no model number came, just that it was a Xeon processor.

  When I install ESXi on this server (I turned on hardware virtualization in the BIOS), the installation looks ok, but when the computer restarts, it always seems to try to load my old server CentOS so it's as if the installation has not completely replace the drive. Raid Controller had 2 virtual disks so maybe I didn't replace what was a disc of "boot"?  I will try that next.

  Guess I'm looking for confirmation that the CPU is ok and I'm missing nothing else.

  Thank you

  Charles

  1 in the raid bios remove the raid and create a new one, and then reinstall esxi.

  2 when you install also use iso Dell:

  do both and you should have a running system.

  http://www.Dell.com/support/drivers/us/en/04/DriverDetails/product/PowerEdge-R620?driverId=XWYR5&osCode=XI51&FILEID=3005015335

  This is the link above

  I try to keep updated here: http://sparrowangelstechnology.blogspot.com/search?q=dell+iso

• Can I install the vmware tools on a HP Proliant 380 G5 with VMware ESXi 3.5 Installable U3 with HP management components?

  Hello, I have install ESXi 3.5 U3 on a Hp Proliant 380.

  I have created a virtual machine to Windows 2003, and when I want to install VMWARE TOOLS from Vmware Infrastructure Client, it does not install on the virtual machine vmware tools. Nor has received all messages from a Client Infrastructure and neither of the virtual machine.

  Why could this happen?

  Thanks in advance

  NO.

  The installation of vmware tools lies in an iso file, which is located on your host ESX itself and is mounted on the virtual machine when you click "install vmware tools".

  Weather or not your host has a cdrom drive is not serious, you can always add a virtual cdrom drive to your guests and use iso files, or the cdrom drive on the PC that you are using the VI client from.

  If you vm doesn't have a virtual cdrom drive, it can't mount the vmware tools iso, and you cannot install the vmware tools.

• Satellite M70 do not charge the battery

  My satellite M71 do not charge the battery, not only when works now, but also when power is off. Do not charge batteries supplied with the adapter plugged.

  Hello

  I agree with the user above.
  This really looks like a malfunction of the battery. I put t know how old laptop is but generally cover the battery for about 1 year.

  You know that, after the words of 500 of loading and unloading procedures battery automatically loses performance and battery life battery decreases.
  It s nothing unusual.

  But if the battery is new, you must contact the ASP (partner) in your country.

• VMware esxi 4.1.0 Build U1 on HP Proliant DL 165 G7 348481 (590258-421) processor AMD Opteron 6128HE

  Hi all! I am new to vmware. I install VMware esxi 4.1.0 U1 Build 348481 on HP Proliant DL 165 of the G7 with an AMD Opteron 6128HE processor. Start after the installation of the server has been reset, vmware esxi, but after 5 minutes of work goes in the purple screen and work stoppages. If anyone has encountered this situation and can help me?

  No chance!

  Please note that the DL165 G7 is currently not supported by HP for VMware ESXi (only for ESX classic).

  See their Server ProLiant VMware Support Matrix and note (1) here for DL165 G7.

  You will find the same information in VMware HCL.

  Andreas

  - Blog of experience front of VMware

• VMWare ESXi is not responding

  Hello
  
  I have a server at home with a Q6600 Quad Core and 8 GB RAM running with VMWare ESXi 3.5 for about 8 months now. I have 2 warehouses of data, with 1 TB (SATA HDs), each with 150 GB free and the other with 240 GB free. I have 9 virtual machines running 24 x 7 on it. Everything has been done, until yesterday.
  
  Out of the blues, I stopped to get the answers from the MV in the ESXi. Initially, I was able to connect using the Client Infrastructure but, when if I tried to get information from any virtual computer, I receive a message that the virtual machine could not be reached. Looking at the info from the host, he would show me info network, cpu, memory, but when I tried to reach the data store, it would normally stop responding. I couldn't open the located data store where ESXi is installed once, and all virtual machines were there. Now, I can not connect more, and I don't really know what to do.
  
  What is the best course of action to diagnose the problem? I can access the ESXi screen without problem, but I don't know what to do. I thought to reinstall, maybe with version 4.0, but I'm not sure I should do it. Where (and how) can I access what anyone who could help me figure what's wrong?
  

  TKS

  Try these options in the following order:

  1 reset the Management Agents: http://pubs.vmware.com/vsp40u1_i/wwhelp/wwhimpl/js/html/wwhelp.htm#href=setup/t_restart_mgmt_net.html

  2. restart Management Network: http://pubs.vmware.com/vsp40u1_i/wwhelp/wwhimpl/js/html/wwhelp.htm#href=setup/t_restart_mgmt_net2.html

  3. restore the vSwitch standard: http://pubs.vmware.com/vsp40u1_i/wwhelp/wwhimpl/js/html/wwhelp.htm#href=setup/t_restore_stnd_switch.html

  4. full reset: you loose all the configurations you made on the ESXi server, but the guests are kept.

  http://pubs.VMware.com/vsp40u1_i/wwhelp/wwhimpl/js/html/wwhelp.htm#href=Setup/t_reset_the_configuration_defaults.html

  AWo

  VCP 3 & 4

  \[:o]===\[o:]

  = You want to have this ad as a ringtone on your mobile phone? =

  = Send 'Assignment' to 911 for only $999999,99! =

• Do not charge the MacBook Air battery

  My macbok Air shows the power is plugged in, but the battery is not charging. The battery status is normal. The adapter led is orange.  I have reset the smc, but it has not changed anything Suggestions?   I thought a new battery and power cord would solve the problem but it doesn't.  Thank you

  Reset the SMC could solve the problem.

  Reset the management system (SCM) controller on your Mac - Apple Support

• Battery does not charge, but by Satellite Pro L510 is running in battery mode

  Hi, I had a few odd battery problems these days:

  I had charged my laptop completely to 100% and then used it on the train on my way home (in Windows 7 64-bit), how I got it to about 70%, shut down normally, put it in my bag and left there until I got home. When I got home, I tried to turn it on but it lights and battery light orange blinking indicating that there can be no charge. I plugged it in and it worked as usual (Linux), so don't think too hard on this subject.

  Later I realized that the battery was still the load after longer that it should have been and running the acpi + (linux) command told me has the battery + charge, 0%, charge at the zero rate - will never fully charge. + I disconnected to see if it worked, and the battery lasted as usual, although always it's 0% charge rate.

  I started in Windows 7, and the battery reported that it was at 68%, so I assumed it was back to normal. A while later, I noticed that he was still 68%, despite having connected for a while - at least an hour. Start on linux, acpi showed data battery normal search, except that it was 'blocked' to 68%.

  I disconnected the laptop and run it as usual, and it ran until he cut; I guess with him out of power. I plugged it back in and it is 'charge' again, even if it is still 0% battery and "load at the zero rate".

  Before all this happened, the battery works well - apparently to 94% of its capacity. It would be modified for a few hours unplugged play movies or games.

  Summary: PC laptop battery suddenly going to works "attributed to the zero rate" and 0% complete; battery still seems to work very well, seems fresh and portable no power plugged in but the battery is not 'charging' or have his percentage of charge remaining increase.

  Someone at - it ideas? I have yet to try a BIOS update, but it seems that there is one available, so I will give that a try. I feel that the problem is not the battery as the battery controller, so I don't want to invest in a new battery without knowing it, the problem will be solved.

  Thank you!

  Hello

  I think you should try upgrading the BIOS
  BIOS default value, and then try to charge the battery again.

  > get the impression, the problem is not the battery as the battery controller, so I don't want to invest in a new battery without knowing it, the problem will be solved.
  Well, it of really difficult to tell if the battery or the mobo may be affected
  In my opinion, the battery must be tested without a doubt

• Satellite L50 - A - 19 p - 0% battery and not charging

  Hello
  Since this morning, I have problems with my laptop battery.

  Even with the domain controller is connected, the suspension of the battery at 0% not charging and after a few seconds, Windows goes to sleep by itself.
  I tried to start Windows in safe mode and the battery seems to work without even plugged DC so at 0%.

  Now I use the laptop without the battery and only with DC power.

  Is there something I can do to solve the problem?

  Thank you!

  Try to uninstall the ACPI compatible control method battery.
  This can be found in the device-> battery Manager

  Once the compatible ACPI control method battery driver disappeared (uninstalled), click on the 'Action' menu at the top of the window and select Scan for hardware changes.

  This should reinstall the removed driver...

  But if it does not solve the problem of battery, keep off compatible ACPI control method battery.

• HP ENVY m4-1015dx Notebook PC: hp envy m4 battery not charging but fresh when the laptop is turned off

  Hello!

  I was with my hp envy m4 core i7 for quite a while now... recently, I formatted and installed windows 8.1 64-bit installed. I decided to download some drivers from the hp site and I realized I needed to provide my model of laptop model number I could not remember so I decided to remove the battery while the computer is still connected to the power for the number, then I went back to the battery. the latter, I realized that the cell had not accused beyond of 7%, which was the level of support, until I removed the battery and when I checked the charge level, it indicated that it was plugged in but does not support. When I tried to repeat the entire process as well as close the laptop, remove the battery and turning it again nothing work and completely refusing to charge for its on.when I decided to turn off completely and then it was off it perfectly complete accused 100% operating battery estimated more than six hours of charge time, guys help me to understand what might have developed and what will be the best solution.

  Hi @Phanz,

  Thank you for your inquiry.

  I entered which you have tried to download the driver on the HP website for your laptop but realized you need the model number.  You have removed the battery while the laptop is running.  Now when you reinstall the battery, it shows that it is connected but does not charge and continues to 7%.   You have repeated the process and close Notepad and removed and reinstalled battery, but there was no change. If you turn off it charges the battery to 100%.

  You did all your Windows updates?

  Have you tried the troubleshooter in Windows?

  First of all, I would like to try a Windows restore to before remove you the battery.

  HP computers - using the Microsoft System Restore (Windows 8)

  If restore doesn't work or is not possible, you could try a Refresh Your PC to solve problems (Windows 8).

  Then you can try the following steps.

  HP laptops - test and calibrate the battery (Windows 8)

  The battery method compatible ACPI Microsoft control is basically the driver that communicates between the computer and the battery. There is a chance that it became corrupt and bad reads the battery level.

  Step 1. Go to the Device Manager
  Step 2. Select the stacks
  Step 3. Click with the right button on the "Microsoft compatible battery ACPI Control method" which is in the list
  Step 4. Click on uninstall
  Step 5. At the command prompt, put a checkmark in the box to remove the current driver
  Step 6. Shut down the computer

  Step 7: Remove the battery for a minute and then put new
  
  When the computer returns to the top it should automatically find the driver.
  
  Step 8. Go to the Device Manager
  Step 9. Select the stacks
  Step 10. Click with the right button on the "Microsoft compatible battery ACPI Control method" which is in the list
  Step 11. Click "automatically search for an updated driver.

  Do the same thing with embedded controller compatible ACPI Microsoft.

  Last option is to reinstall your Windows 8.1 Pro.

  Good luck!

• VMware ESXi does not support the RAID on HP Proliant ML110 G5 drives

  Hello

  I installed VMware ESXi on my HP Proliant ML110 G5. I got 3 hard drives on my server at the moment, one of them is VMware ESXi and other two are RAID1.
  Whenever I connect to my server via vSphere client I have the chance to see every HARD drive (datastore) separately.  Is it possible that VMware does not RAID installation?
  I would need to see these two hard drives as a data store. Do you have any ideas on how I can do?
  Thank you.

  like any other typical server, you need to configure the sata raid controller RAID5/RAID0. but keep in mind that this controller without any battery backed cache would have very horrible performance. Another way is that you can use datastore span to provide as a large store of data, but if you lose all of the computer, you will lose all data.

• iPad Pro does not charge

  My iPad Pro (10.0.2) says not charging when connected to the nearest 4th USB port of lightning on my iMac OSX end 2015 10.11.6. Another thing that I connect it works so there is nothing wrong with this port.

  However, my iPad charges when it is connected to the other 3 USB ports. Tried other Apple cables, restarted my iMac and reset my iPad.

  Basically, it's not the iPad, and it's not USB port cuz that they both work when plugged in with something else. It's just the 2 at the same time with the other who do not work.

  I'm so confused. Does anyone else have this problem?

  Hello. It seems that the charge voltage/current monitoring software has been changed in iOS 10. It is much more sensitive. Your device's charge when says "do not load", but he is in charge, probably faster when it shows the Flash. See the iPad is cool the computer after an upgrade to iOS 10 batches of a discussion of this issue.

• Started at Mo and not charging with the charger connected. Charger works. Keyboard not workin except power button / stop. Restarted using ex in car without success. SW

  Started MacBook and not charging with the charger connected. Charger works. Keyboard does not not except the power button / stop. Restarted ex drive no available help hoping that it was a matter of SW. SW and the operating system works very well. Read some info online. Tried to reset the SMC. Now, the MacBook does not start. Can U help me please. Thanks in advance.

  MacBook, 2010, Mac OS X 10.6.8

  Hi Veronica Steward,.

  I understand that you have turned into a series of questions about your MacBook and want help getting the computer to turn on. Here is an article that can help you through the steps to fix this problem:
  

  If your Mac will not turn on - Apple Support

  Let us know how it goes and thanks for coming to Apple Support communities.

  See you soon.

• Does not charge

  Hi all.

  I have a question - my iPad 2 Air will not charge when connected to my computer (didn't load in the upper right corner).

  Using cable that the iPad is connected to the computer, disconnect the computer and the plug in the wall socket and it will load.

  I plugged my iPhone 5 on the computer and it will charge - the same thing with my iPod.

  Anyone have any suggestions on how to solve this problem.

  Hello

  I use app loader on the computer AI to charge my iPad

  http://www.applestan.com/wp-content/uploads/2012/08/AiCharger_V10006_XpVistaWin7-2.zip

  First reboot your iPad and then connect it to your computer, at the beginning it says "do not load", but then it starts to load.

  Hope this works,