HP SlimDesktop 450-a114: controllers for HP SlimDesktop 450-a114

Similar Questions

• I have microsoft windows xp home edition. where can I install video controllers for the draw direct 3d and acceleration

  I did the thing dxdiag, and he said that it indicates the 3D features Direct is not available.

  Hi anom_,

  1. What is the brand and model of your computer?

  2. don't you make changes on the computer before this problem?

  You can follow this link & check if it helps.

  DirectDraw or Direct3D option is unavailable

  Hope the helps of information.
  Please post back and we do know.

• 450 a192na: 450 - a192na drivers for Win7 x 64 - help! :-)

  Hi all

  I'm really struggling to get Win7 64 bit drivers for the HP Slimline Office 450-a192na.

  I found this thread:

  http://h30434.www3.HP.com/T5/desktop-hardware-and-upgrade-questions/controllers-for-HP-SlimDesktop-4...

  .. which is close to what I'm looking for, but I can't find a graphics card or sound controller.

  Any help would be appreciated!

  Thank you

  James

  Hi, James:

  I think you're out of luck.

  I checked each pilot Bay Trail HP Intel graphics card and none are for W7.

  Here is the audio driver of a different model with the same motherboard...

  This package contains the Realtek HD Audio driver for the supported desktop models that are running a supported operating system.

  File name: sp72442.exe

  The only suggestion I can offer for the graphics would be to try one from Intel.

  Exe and zip 64-bit files are the two last registered on the left side of the Web page.

  https://Downloadcenter.Intel.com/download/25698/Intel-graphics-driver-for-Windows-7-8-1-10-15-33-

• Audio driver and modem for Satellite A30 151

  I've updated my Toshiba with Windows XP PRO/SP2 laptop.
  After installing I found that Windows XP/sp2 is not installed the modem and audio devices.

  I tried to download the drivers from the site and tried to install. I got the error message saying driver software is incompatible with the version of the operating system service pack.

  I watched on the web and found that there is no driver for Windows XP/sp2 version.

  I tried both ways of performing the installation of the driver software and trying to install using the inf file.

  At the same time in vain. It is hard to believe that there is no resolution to this problem. I deal I forgot this site to have the right to files already lying in the site for Windows XP/SP2. Could someone send me the url of the software driver for the modem and Audio controllers for my system (Satellite A30 151) under Windows XP/SP2.

  Thanks in advance for all the help and your time

  Gobethavam.

  HI Lorraine,.

  The site of Toshiba UK lists the following modem drivers: -.

  2122ALL05

  31116ALL5 (for internal V90 modem)

  They have the same date, September 19, 2003 and are specific to windows XP that should of course include XP Pro.

  http://UK.computers.Toshiba-Europe.com/

  HTH

• For HP ENVY dv6-7213nr Windows 7 USB controller

  Recently, I've killed my HP dv6-7213nr Windows 8.1 want to Windows 7 Professional.

  I tracked most of the drivers for it in various sites, but I still need USB controllers for her. The closest to the power cord works, but that's all.

  It's a USB 2.0 controller.  I looked everywhere I know online and found nothing on this subject.  Any help?  I have seen a lot of post on the decommissioning and the difficulties in finding different drivers, it's a pain.

  Thanks for any help in advance!

  Hardware IDS are as follows:

  PCI\VEN_1022 & DEV_7812 & SUBSYS_182D103C & REV_03
  PCI\VEN_1022 & DEV_7812 & SUBSYS_182D103C
  PCI\VEN_1022 & DEV_7812 & CC_0C0330
  PCI\VEN_1022 & DEV_7812 & CC_0C03

  USB 2.0 is supported by native drivers included in Windows 7. The hardware ID 'PCI\VEN_1022 & DEV_7812 & CC_0C03' you provide is an AMD USB 3.0 controller. Please try the Drivers of the Chipset AMD (USB 3.0, AHCI and Chipset) from AMD. The first driver is for Vista, 7 and 8.

  If you have any other questions, feel free to ask.

  Please click the 'Thumbs Up' white LAURELS to show your appreciation

• LabVIEW for control unlimited, a camera and a light meter (Minolta T - 10A)

  Hello world

  I'm totally new in the use of data acquisition software, but I found out, I use LabView for continuous measures (intervals of 15 min for 1 month or maybe more), the thing is that I need to get pictures simoultanously (Canon camera EOS) and illumination (in lux) device: Minolta T-10 a vision series T-10MA. My question is what software LabVIEW do I need to buy (or my institution actually) in order to get this. I look at the options of LabVIEW software and cannot understand what is needed. Subsequently, I guess that I need controllers for each of the devices (minolta and canon). Can you please tell me if this is possible and how to do it. I would really appreciate it.

  Steph.

  The following items are required: LabVIEW full, all drivers of devices (including DAQmx and pilots of the Vision) and the Acquisition of Vision software package.

  The Minolta luxometer has a connector for a PC and some communication software (which I did not inspect) which, I suppose, would allow you to take readings.  There is a comment about current if the USB cable is connected - I don't check if there is a power connector on the luxometer (since you will need to leave it plugged in for a month, the same problem with the camera).  As far as the camera is concerned, I don't know if it is controlled from a PC - my experience has been with (the size of 640 x 480 pixels) video cameras, which are probably controlled by LabVIEW.

  As for simultaneous readings, it is something that LabVIEW did pretty well.  I advise you to consult a professional if it's anything other than a school project, maybe even hire someone to work a few week of.

  Bob Schor

• What architecture for my application?

  Hello!

  For my test bench, I developed the LabVIEW software. In the last months, I asked several questions in this forum, but always about the details of my application. Until now, I never really questioned the general architecture (which is certainly a mistake, that I want to learn).

  What drives this desire to review my work, it's that I am currently not able to interrupt the complete progam or subfeatures of controlled prematurely or if errors occur.

  I hope you could give me some suggestions which would fit my application better. I'm not really experienced in structured programming, use for example architectures producer/consumer etc and I'll read up on them, but first I need a general boost in the right direction.

  First a brief overview of my hard - and software:

  HW:

  • 3 different controllers control of actuators
  • 2 different cameras

  SW:

  • Front for the interaction with the user
  • Several measurement routines that use different combinations of actuators and cameras. For example "move to position 1 and take a picture, then move on to position 2, etc.. These routines can be quite long, including the analysis of the images and decisions based on the results. These routines must sit in event of an event structure that in turn lies in my main program (the program of the façade).
  • Void / screw (lowest level in my software) who send the actual orders for controllers, for example 'move', 'read the current position' etc. These Sub VIs are separated from my Panel VI and consist of structures events themselves, an event for every basic function. These event structures are controlled from the front panel via the dynamic user events. So basically a push of button on the remote.

  Finally a very brief example of workflow in my software:

  1. Façade is started. Along the SubVIs for controllers are also started
  2. Lance user measure routine N1 with a button
  3. Start of the event in the front panel. In this case, other events are generated sequentally, according to the algorithm of measure.
  4. These remote events live Sub point 1, for example remote press the buttons for the basic functions in the desired order (move, take photo etc.).

  Problem is that the user cannot terminate measurement routines before they are completed, because the program is locked up in the case of corresponding event.

  In addition, when a controller reports an error (e.g., loss of power), as routine orders keep coming which results in more errors.

  This should be possible with my new architecture:

  • The user in the front panel (as before)
  • Premature termination of all auxiliary program if the user wants or if the error occurs. Then a defined State must be entered (including closure of all references, power off all devices, etc.)

  I'm not at work right now, but I'll upload some screenshots later because let's face it – which was a wall of text

  But maybe it's enough for a few first thoughts of you?

  Thank you!

  I tend to like to have HAL - so I tend to create a module that is designed just to communicate with the instrument and then my main loop of the program (e.g. routine measurement / logic program) interact with that and sends updates to the user interface. This is because if I want to use this material in another application, I can re - use the 'module '. It's perfectly OK to have your material combined with your message loop - loop, but if it takes a long time to read the data of the instrument, your application would be not as sensitive to the façade events (because it must wait to finish first).

  So, you could have:
  -UI event loop
  -The main Message loop (responds to user interface events and your program 'flow')
  -Hardware Loop (to initialize and communicate with the instrument)

• How can I get updates for IDE ATA / ATAPI Controller for windows xp pro

  Where can I find drivers updates for IDE ATA / ATAPI Controllers for windows xp pro?

  These are usually Microsoft drivers, and they are as old as the hills, why do you need to update the drivers?  If the Microsoft drivers are not appropriate, then get the drivers from the manufacturer of the motherboard.

  John

• Standard host controller USB OpenHCD (Code 24) for windows 7

  Hello

  Using windows 7 computer and with WYSE also. Frequently, get error code 24 in Host Controller Standard OpenHCD . If I restart the system and then its works fine. After a few days its happening. Kindly help me to overcome this problem.

  Kind regards

  Sery

  Hello

  There might be a hardware issue, and you cannot resolve hardware with the software. However, try the
  following methods that could help solve the problem.

  Code 24: This device is not present, is not working properly or is not all its drivers installed
  http://TechNet.Microsoft.com/en-us/library/cc771552 (v = ws.10) .aspx

  Remove corruption if there is:

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  or

  sfc/scannow damaged = c: \ /offwindir = c:\windows

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  Then run checkdisk (chkdsk).

  How to run check disk in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  ------------------------------------------------------------------

  Then lets refresh the USB stack

  Control the click Control Panel - Device Manager - no matter where in the box of white/white - then the VIEW - see the
  Devices disabled - look around (with the exception of USB controllers) for your camera (can have
  zero or more than one) and top - right click UNINSTALL.

  Control Panel right CLICK on EVERYTHING - Serial USB controllers - device configuration-manager and
  UNINSTALL all but the category itself - REBOOT - it refreshes the driver and battery USB

  This KB shows XP how to and methods of Vista and Windows 7 are the same
  http://support.Microsoft.com/kb/310575

  This is a utility to help you, but do 1 above.

  USBDeview is a small utility that lists all USB devices currently connected to your computer.
  as well as all USB devices that you previously used. Run Options and tick three 1
  are there choices to see if any.

  http://www.NirSoft.NET/utils/usb_devices_view.html

  You must remove all instances of the devices and restart.

  ----------------------------------------------

  After ALL the foregoing:

  Check with support of the manufacturer of the system (motherboard for customized systems manufacturer), their online
  documentation and drivers, diagnostics and ask questions in the forums about known problems. Update
  the BIOS, drivers low-level chipsetand drivers of major on-board and separate devices. And
  all systemic USB drivers.

  ----------------------------------------------

  If necessary try these two:

  Tips for solving problems of USB devices - and a Mr Fixit
  http://windowshelp.Microsoft.com/Windows/en-us/help/c39bd203-f729-47a4-8351-83291e13c8a81033.mspx#EGB

  Hardware devices not detected or not working - Mr. Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• WLC Campus Design - 10 controllers etc.

  Hi guys,.

  If I have the following scenarios,

  2 sites and each site will be broken up by 100km (just an example to show that wireless reached between them) and have 100 APs in each site.

  Please see the attached diagram.

  Both sites have two controllers on site or a domain controller centralized (if there is a preferred method)?

  Anyway,.

  Two controllers for site1 (1 on each DC for example) should be in the same group of mobility.

  Site controllers 2 should be in a different group of mobility?

  Also, if this design developed by a factor of 5, and we had now 20 + controllers, controllers each either on one VLAN separate in the domain controllers or could I create a controller wireless VLAN that has all the controllers connected to?

  Please note that, on the previous point, the domain controllers have NO VLAN for layer 2 between them, so that each set of controllers (by site, one in each ms) are sensitive to the layer 3 wanders, but the basic principle, we will use is that each site will have a PDC and a BDC and all items should be on the same controller.

  Also, for most small Wireless deployments, is better to have a set of controllers of nmanager small sites, say for APs 5 to 10 per site? BUT then, you can't have a group of mobility for the controller so would this cause a problem? Oh, now I'm confused?

  Anyone can comment on the above drawings?

  Thx a lot.

  Ken

  REAP H works well in the code of 4.2. I have about 30 sites with the up to 5 1252 mode operation REAP H return to the a single domain controller. The domain controller has 2 4404-100 and I divided the primary one and secondary to the other sites.

  As for redundancy, should watch how you manage the clients ip address. N + N is the most popular because you always have 100% redundancy. It can either be on site or to the domain controller.

  Now you can also make N + 1, one in the local site and the other in the domain controller. Now, you have to look at what ip address users will get when they are on the wlc primary and when the primary fails and AP, go to wlc backup. Now, you have clients getting and the ip address on the central site (DC) and the traffic here. So now, you have to watch the traffic flow and how you configure your acl, if necessary.

  N + N + 1 can work for you if you have a WISN in the two DC. Then for the site 1:

  Primary school DC1WISM1-WLC1

  High school DC2WISM1-WLC1

  Tertiary DC1WISM1-WLC2

  Or you can have a 4404-100 on each site that primary and a 4404-100 on each secondary and tertiary domain controller. You will need one at each site and two on each controller domain just for two remote sites. Now, please understand what is needed for smaller remote sites.

  It boils down to cost and is it better to keep the wlc on site since if the wan goes down, resources is not available on the domain controller. Also if you place the different primary and secondary or tertiary in ip subnets, how will you manage ip addressing customer will get from the wlc.

  Also... Stick with the 4.2 If you need to deploy h - harvest. Do not go with the 5.0 or 5.1 again. %.0 is the worst and 5.1 is too new and could focus on the issues raised in the 5.0 and could introduce more.

• Windows controllers USB 8 not on the Device Manager list

  Bus controllers series not on the Device Manager list. USB ports not working do not. I tried equipment difficulty and said could not find drivers for multifunction device clicked on fix not found the drivers for it. could use a little help with that.

  USB windows 8

  Hello

  Sounds like hardware and you cannot resolve hardware with the software. Check with the system
  Manufacturer of support, their books online, the diagnosis and ask in their forums (if
  There are). Or check with a real computer store (one who does on its own in-store service
  This brand and model of laptop).

  Remember that you can not resolve hardware with the software.

  =====================================================

  Troubleshooting you can try:

  Note the use of Win Key + X and Win Key + W (to go on the Control Panel, Run and parameters
  According to needs). Win + D key calls the office and using Win Key active / disable the Office
  and the splash screen.

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Windows key + X (or right click in the lower left corner) - (Admin) command prompt

  C:\Windows\System32\ >

  At the prompt, type in SFC/scannow above
  (There is a space between C and /)

  How to run the command "SFC/scannow" at startup or in Windows 8
  http://www.eightforums.com/tutorials/3047-sfc-scannow-command-run-Windows-8-a.html

  -----

  Then run CheckDisk (chkfdsk/f/r)

  File (formerly Windows Explorer)

  Right click on drive C: - Properties - tab tools - error checking - Check

  Windows 8/8.1 - improve performance by optimizing your hard drive - see "to repair a drive:
  http://Windows.Microsoft.com/en-us/Windows-8/improve-performance-optimizing-hard-drive

  How to check a drive for errors with "chkdsk" in Windows 8/8.1
  http://www.eightforums.com/tutorials/6221-chkdsk-check-drive-errors-Windows-8-a.html

  -----------------------------------------------

  Then lets refresh the USB stack

  Control the click Control Panel - Device Manager - no matter where in the box of white/white - then the VIEW - see the
  Devices disabled - look around (with the exception of USB controllers) for your devices (can have
  zero or more than one) and top - right click UNINSTALL.

  Control Panel right CLICK on EVERYTHING - Serial USB controllers - device configuration-manager and
  UNINSTALL all but the category itself - REBOOT - it refreshes the driver and battery USB

  This KB shows XP how to and methods of Vista and Windows 7 are identical (and
  Windows 8/8.1)
  http://support.Microsoft.com/kb/310575

  This is a utility to help you, but do 1 above.

  USBDeview is a small utility that lists all USB devices currently connected to your computer.
  as well as all USB devices that you previously used. Run Options and tick three 1
  are there choices to see if any.

  http://www.NirSoft.NET/utils/usb_devices_view.html

  You must remove all instances of the devices and restart.

  ------------------------------------------------------------------------------------------------

  Install USB 3.0 and other USB devices
  http://Windows.Microsoft.com/en-us/Windows-8/install-USB-3-USB-devices

  Hardware and drivers
  http://Windows.Microsoft.com/en-us/Windows/hardware-drivers-help#hardware-drivers-help=Windows-8

  Set up your PC - configure your devices
  http://Windows.Microsoft.com/en-us/Windows-8/set-up-devices#1TC=T1

  Why Windows is not find my device?
  http://Windows.Microsoft.com/en-us/Windows-8/why-isn ' t-windows-conclusion-device

  What happens if a device is not installed correctly
  http://Windows.Microsoft.com/en-us/Windows-8/what-device-isn ' t-installed-correctly

  ===================================================

  If necessary:

  Try to do a "Refresh you PC without affecting your files" (or modification of your personal data
  settings) or even a restore.

  Windows 8/8.1 includes special discount methods (keep files and settings) or a reset
  (new installation remove all).

  How to restore, refresh or reset your PC
  http://Windows.Microsoft.com/en-us/Windows-8/restore-refresh-reset-PC

  How to create a system image to refresh your PC in Windows 8
  http://support.Microsoft.com/kb/2748351

  How to update Windows 8/8.1
  http://www.eightforums.com/tutorials/2293-refresh-Windows-8-a.html

  How to reset Windows 8/8.1
  http://www.eightforums.com/tutorials/2302-reset-Windows-8-a.html

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• controller for several regions of the

  Hello
  
  I create a new page. This page includes several regions. I have a single VO that queries data from different tables, but that data should be divided into 3 different areas on the same page.
  
  So, to do this, I created a provision of battery and 3 presentations of single column under this provision of the battery. I created the controller for the disposal of the battery.
  
  My question is:
  
  Create 3 controllers for 3 single column page layouts? or should I give the name of the Stacklayout controller to these layouts also.
  
  Thank you very much
  PK

  The intention of a controller must manage some initializations and events page. Donot you must have a controller in each region. A controller at the pagelayout region can handle events on the entire page.

  Anyway, in your case you have only a single VO that must be performed and the data displayed in three regions. Hope says.

  Concerning
  Sumit

• shutters control home automation

  I want to renovate my metal, electric shutters.  at the present time, I have a button for opening and closing on the wall.  I am in a country of 220 volts.

  Does anyone know of a remotely controllable rehabilitation project (through it Mac?) switching system?

  Thank you.  (hope this is the right forum to post this)

  There are several different home automation standards.

  • Apple HomeKit - then that controlled by Apple is open for use by other manufacturers
  • Z - Wave - independent standard
  • ZigBee - mainly used to control the lights
  • ioHomeControl - rare
  • X 10-very old travels the power cables

  and then there are some owners including systems

  • Crestron
  • Control4
  • Samsung Smarthings
  • INSTEON

  which can be linked to various other products

  There is Mac software for some of them and iOS apps for most of them. From a perspective of Mac, take a look at https://www.indigodomo.com/

  But, you are probably better off watching iOS apps, you might even wall mount an iPad and use it as a controller. You could also use an open-source solution and control via a web browser, some people do with a Pi raspberry running Linux and equipped with a software module and Z-Wave as a OpenHAB race.

  I look at using Samsung Smartthings to control various other systems, Smartthings as standard can control Z-Wave and Zigbee devices. There are several controllers for wheelchairs/roller shutters using the Z-Wave standard, which means that you can use one of people with Smartthings. Also from Indigo supports both the Z-Wave he too could control a rolling Z-Wave/component.

  Note: Z-Wave uses radio frequencies different in the USA vs Europe so make sure you get the right products for your location.

• HP Jet 7 - Windows 10 build - not folded screen rotation Option / available (manually made only)

  I managed to finally get a copy of Windows 10 on HP 7 (5701na) flow everything was fine except for 2 things.

  The first was the touch Start button was not working but found another job to install a SP to resovle this.

  But I still have no options under the "Auto-Rotate" value display on. There is a driver intel installation which allows me to manually set (in most windows display settings) but on a friends machine (same model, etc.), there is an option under display settings to adjust the auto rotation on.

  Have checked the device drivers and the accelerometer has installed ok and I have no camera to errors / warnings.

  Someone else has the same problem with the preview Windows 10 technical or current?

  On your HP Jet 7, click on the link for the drivers:

  Drivers for the HP Support tool

  It should detect which tablet that you have and that you run Windows 10.  Download the utility: HP Support Assistant software. (you may need to tap the plus (+) to see) It should be the only option.

  After this, change your Windows 8.1 operating system so that it displays all the drivers. Download driver-Driver Pack as shown below called: Intel Chipset, graphic, photo, and Audio Driver Pack. Select this option to use the driver to download and install support tool.

  

  You can then do the same with the two drivers in the pilot controllers for the contact.  With these updates two pilot / installs I now anti-rotation on my quick actions in the center of the Action, and my button to the homepage of Windows works.  A reboot may be necessary later.

• Portege R500: Card reader SD and ODD do not work - drivers needed

  I have laptop portege R500, product number: PPR50E-04X04WCE.

  last year, I changed the operating system and installed windows 7.
  Since then, I can't use the dvd drive or the sd card reader.
  And the control panel it apears two unknown devices, but I can´t find the controllers for these.

  What can I do to fix this?

  I assume you found unknown devices in Device Manager.
  Check it please http://forums.computers.toshiba-europe.com/forums/ann.jspa?annID=78
  Here you can find instructions how to identify the unknown devices.

  I checked the Toshiba download under http://www.toshiba.eu/innovation/download_drivers_bios.jsp page and your Portege is listed there, but under the option ARCHIVE. It is supported for Win7 so there is no problem to install all the drivers available.

  Check it out please and let us know if you still have the same problem.