HP stream 11-d010wm: I have a hard time to start the system it asks me the password for administrator password or power

Similar Questions

• 15 170tu ac: I HAV to press the power button several times to start the laptop...

  I HAV to press the power button several times to start the laptop... works well with the power supply on.

  all My drivers & bios is updated... but when I opened the lid... I HAV poer press several times the button and he then began 4-5 min.

  Hi @Vishalwagh123,

  Welcome to HP's Forums a great way to get help. It's a great place to find answers and advice! Thanks for the post.

  I understand you have questions turn on/off the device and you must press the power button several times for him to start. I'll be happy to help you.

  Please try these steps first. Perform a hard reset.

  • Steps to do:
  • Turn off the computer and unplug the charger. Then remove the battery.
  • Press and hold the power button on the unit for 15 seconds to carry out the static electrical charges inside the machine.
  • Replace the battery and the charger plug it back. Try to turn on the computer.

  If it fires up immediately the issue is resolved. Otherwise, try to turn on the computer without the battery and check that it works immediately.

  In your message, you said that it works very well with the charger. However, I need more clarity here to help you better.

  It works immediately when the adapter is connected and the power button is pushed only once?

  If you again press the power button several times, it may be a faulty power button, and you will need to contact the hotline at the service of the unit.

  Let me know what happens when you try to turn on the unit without the charger?

  Visit this link to contact support phone:

  http://HP.care/2bjG4nE

  Hope the problem is solved without hassle. Please keep me in the loop.

  Take care and have a week Holy.

• If you say that you have sent me Email to change the password, they have not been received.

  If you say that you have sent me Email to change the password, they have not been received.

  Several times I used sync for tranzfer of information to a new computer and or updated computer!
  In the last 24 hours I've sent many requests for 'change password' for those that I tried did not work, so I can connect!

  You say you sent an email over and over again, but no one came to my email which is confirmed you have the right address!

  There is absolutely no evidence that you tried to send an email to me, I checked the spam, I even looked to see if somehow, it went one folder other then my Inbox, nothing has been received on your part!

  Michael Serota

  Removed edit email and public telephone for spammers robots do not find.

  You can enter the wrong email address. I tested 2 fake emails in the password reset page and received the green check mark telling me that the password reset emails have been sent. It is not a real confirmation that your e-mail address is used by Firefox accounts.

  This is done this way so that hackers and spammers can not cheat the system by typing many kinds of emails at random and wait to see if they get a confirmation 'this e-mail address is. So for security reasons, all the entered addresses electronic are treated as real even if there is no account that corresponds to this e-mail.

  Please try some of your other email addresses here and see if you receive a password reset email in these accounts.

• I downloaded the Microsoft compatibility pack. He asks me to double click the File Format Converter.exe file on my hard disk to start the Setup program.

  Original title: could not open the file.

  I received by e-mail a file which I can not open... so I downloaded the Microsoft compatibility pack. He asks me to double click the File Format Converter.exe file on my hard disk to start the Setup program.  I'm not savvy and don't know where to find it!  Your help will be admired.  BF

  Hello, I downloaded myself today and when I read your question, I went looking for him.

  The only place where I found it was prefetch.

  However, I was able to view the file after downloading.

  When I download I always save it to the desktop, then the scanner and then double-click it to install. If you haven't noticed where it was installed, check your temp folder.

  Or download it again and save it to the desktop.

  I hope this helps.

• WHY DON'T I HAVE TO PRESS F1 TO START THE COMPUTER?

  WHY DON'T I HAVE TO PRESS F1 TO START THE COMPUTER?

  We could not tell you, it's a function that is located on the computer itself, only not part of the Windows operating system.  However, this means that the computer has a failure any and he's trying to tell you about it.  What does the screen say?

• Hi, I have 0xc0000142 error when I start the first pro after the last update, before that I had no problem playing first pro...!

  Hi, I have 0xc0000142 error when I start the first pro after the last update, before that I had no problem playing first pro...!

  Hello Gene,

  You may need to check this: Re: Premiere Pro 2015 won't open after the recent update

  Kind regards

  Navdeep Pandey

• have tried four times to get the trial version of captivate 7 to download on my windows 7 64 bit

  have tried four times to get the trial version of Captivate 7 to download on my windows 7 64 bit desktop and displays download manager a message, it is not compatible with my ie11

  There is apparently a problem with IE10 + because it is wrongly considered IE1.  To work around this use another browser or compatibility view (http://windows.microsoft.com/en-us/internet-explorer/use-compatibility-view#ie=ie-10)

• Given that I have installed Firefox 17.0.1, program became unstable. I have a hard time getting the program to react to start. I try at least 3 times

  As I said, the program does not start on the first time I click on the icon. The hourglass appears for a second or two, and then disappears.
  I try at least 3 times or more before the program responds.
  Should I try to uninstall 17 and reinstall 16.
  I have already uninstalled 17 and reinstalled.

  One possible cause is security software (firewall, antivirus) that prevents or limits Firefox or plugin-container process without informing you, possibly after the detection of changes (update) for the Firefox program.

  Delete all rules for Firefox and the plugin-container in the permissions list in the firewall and leave your firewall again ask permission to get full unlimited access to the internet for Firefox and the plugin-container and the update process.

  See:

  • https://support.Mozilla.org/KB/server+not+found
  • https://support.Mozilla.org/KB/firewalls

  Create a new profile as a test to see if your profile is the source of the problems.

  See "create a profile":

  • https://support.Mozilla.org/KB/Profile-Manager-create-and-remove-Firefox-profiles
  • http://KB.mozillazine.org/Standard_diagnostic_-_Firefox#Profile_issues

  If the new profile works then you can transfer files from a profile in the new profile, but make sure not to copy corrupted files.

  • http://KB.mozillazine.org/Transferring_data_to_a_new_profile_-_Firefox

• My iPod touch 6 says that I used GB 7.3 on pictures of my shared photo streams, yet I barely have pictures and has not implemented the sharing.

  I have 114 MB of storage due to my photos app space. When I click on 'Storage & use iCloud', it shows that I have used 7.1 GB in the photos, and I have only 25 photos and videos in all. It is said that the majority of data is used my my "flow of shared photos", but I never set up who.

  Check how much storage you had when you got the iPod.  It could just be a few pictures noted a greater percentage of your storage space.

• I have a hard time with my card the sound blaster z to synchronize with cs6. If someone can share with me

  I'm having a difficult time with Adobe CS6 synchronization upward with my sound card. Other applications and latency settings are difficult right now. I had 3.0, but my Windows 7 computer is now "deceased". Help, please.

  I agree with everything that comes to say Steve but to try to get you while you're shopping for an audio interface more suited for his work as a doorstop, try the following:

  Go to the windows of his control panel and make sure the SB card is enabled by default on the tabs of the recording and playback.  In the advanced for both menu, affect the bitrate of depth and sample 16/44 100 (CD) or 16/48 000 (video) depending on what suits you best.  Note that your SB card only works in native mode to 16/48 000 so anything else implies a conversion that hides the card on your part.

  Go to the control panel Windows and, under the audio section, cut all the system sounds (because they can hijack your sound card).  Close all other applications that may want to use the card (internet for example).

  In hearing, go to Edition/Preferences/Audio Hardware.  Set the class of device to Mrs on the drop down menus, set the default input and default output to your Soundblaster.  On the master clock set for SB output (it will probably default).  Set about 200ms latency (you need to maybe increase it later if your playback stutters - or you can try to decrease until you get stuttering, then take up a little bit.  Set the sample rate to what you have selected on the sound control panel.

  The Soundblaster will be probably installed its own menu of control.  Go to it and select Mic or Line according to the entry and all that you need for the output.  I can't be more precise than SB continue to change what they call things.

  I hope that'll get you even if this isn't the best compromise for quality and latency.

• Sometimes they have a hard time capture the image on a physical machine

  Hello

  Last night I had a hard time getting the image on a physical computer.  The machine is a windows 200 advanced server with Service Pack 4.  Last week, I was able to do it without any problem with the same thing.  I was finally able to capture the image after that I went into control manual (Add/Remove Programs) and remove the agent then rebooted. Has started the process more.

  The log file is attached. I'm just curious as to why the problem occurred.  I used the Converter 3.0.3.

  TNT

  It could be a problem with the version of the converter that you use. Of the 3.0.3 release notes, in the section "problems":

  New that task fails for source machine remote Windows when navigating backwards in the Conversion Wizard

  When the following circumstances are present, the physical source computer does not restart:

  • You are remote hot cloning a source of Windows 2000 or Windows NT4 machine

  • The agent is installed on the source machine, but the system has not yet been restarted

  • You change the selection in the source and change to the original source before clicking on finish in the Conversion Wizard

  In this scenario, the task will fail with an instant failure error message. The reboot is required to start the snapshot on the source remote machine service if this converter can take the snapshot of the machine.

  You can try to use the 4.0 version converter and see if you can reproduce the error.

  If you found this helpful, please consider naming pointsIt

• whenever I start my computer, I have a message that readsusername and the password do not match. How can I remove this message to come whenever I start my cpmputer more?

  whenever I start my computer a box appears in the middle of my screen with the title identify yourself and the message user name and password do not match (you provided xxxxxxxxxxxx).

  I would like to know how I canremove this message appear each time I start my computer?

  Hello

  1. have you made changes on the computer before this problem?
  2. What is the version of the operating system that you are using?

  I suggest that you try following the steps mentioned below, that if you use Windows Vista and Windows 7 and check to see if it helps.

  Step 1: Check in SafeMode with network.

  You can also check if the problem persists in safe mode with network and check.

  Reference:

  http://Windows.Microsoft.com/en-us/Windows7/start-your-computer-in-safe-mode

  http://Windows.Microsoft.com/en-us/Windows7/advanced-startup-options-including-safe-mode

  If you are able to see the start icon, then executes the method 2.

  Step 2: Perform a clean boot and check.

  To help resolve the error message, you can start Windows Vista or Windows 7 by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/kb/929135

  Note: After troubleshooting, be sure to start your computer in normal mode by following step 7.

  Hope the above information is helpful.

• I HAVE a standard accout with parental control and I would like to know password__I of the administrator have a dell computer__can I know the password of at least account.__plese of the administrator tell how

  I have a dell computer.
  I tried the cmd process for the administrator account, but it failed.
  He said "access denied" before typing break
  I want to know the administrator account because I can not install games and other software

  Well, that's the whole point of Parental controls on your computer.  Rejects the request allows you to install games and do other things, unless you ask the administrator to help you.  Whoever set up your computer created the administrator account and the password.  You'd have to talk to them to get it.

• Does anyone have or know far to obtain the fix for MS Picture it 2002 (kbid 316861)

  -Anyone have it or know the far to obtain the fix for MS Picture it 2002.   (kbid 316861)   MS sites isn't him. Thank you

  Original title: need kbid 316861

  Hi Timothy,

  Thanks for the post. I understand that you need the patch for MS Picture it 2002.

  To help you suggest several steps to solve the problem, I would appreciate it if you could answer the following questions:

  1. what operating system is installed on your computer?

  You can check the link for more information below:

  What version of the operating system Windows am I running? :

  http://Windows.Microsoft.com/en-us/Windows7/help/which-version-of-the-Windows-operating-system-am-i-running

  2 is that you have problems with MS Picture it 2002?

  You can check the link for more information below:

  Picture It! :

  http://support.Microsoft.com/GP/PIC

  3. you receive an error code or message?

  4. have you made any recent hardware or exchange of software on your computer before the show?

  I suggest you to follow the steps in the KB316861 from the link below.

  It is originally in French, but there is an option to translate the page with the help of Microsoft Translator and check the issue:

  PIP2002 error at the beginning of the program:

  http://www.microsofttranslator.com/BV.aspx?ref=SERP&BR=ro&mkt=en-us&DL=en&LP=FR_EN&a=http://support.Microsoft.com/kb/316861/FR

  Your response is very important for us to ensure a proper resolution. Please get back to us with the information above to help you accordingly.

• I lost the Office for an account I have when I tried to delete the password

  I have Windows XP Home Edition.  I had two user accounts, one owner and an administrator, but I've only used the owner, I had given a password.  I saw a tip on how to remove the password for the signature requirement and thus lost the entire account.  More important still, I lost everything I had on my desk, including records very important.  Is there a way to get the account and back office?

  Actually, I could connect is no longer on the account I "lost".   I therefore decided to rebuild what I lost by doing a search for all files that I had lost and change. This turns out be a mistake, because I was 'fixing' them.  In the middle of the night, I had the idea of just using the system restore, restore to the day before where I "lost" my account.  It worked.  I was back in business, but I lost some more recent information and feel the results of editing.  So I was patching up some losses.  But I guess I found my own answer. System Restore brought me back on the account that I had lost with all the files on my desktop safely returned.