HP USB stream 8

Similar Questions

• maximize the USB streaming throughput

  I am trying to speed up my task at hand. I need to send bursts of digital data, 83 bytes long each, at intermittent, but fast intervals.

  I use Port 0 on USB-6251 in USB mode high speed.

  Below some options, I tried

  1 "software programmed" streaming - send 83 bytes U8 no tables on single sample of multi CH DIO write VI repeatedly, no timetable set. Easy but slow relics, about 1 ms by rate of bytes. I wonder if the driver OR use a sort of handshake software for each byte in this mode, limiting speed interval from image to image USB. Is it possible to run faster in this mode?

  2 calendar hardware. I used aboard output internal counter to provide continuous clock, tested anywhere from 500 Hz to 1 Mhz can be much faster than (1), but running into questions:

  a. finished picking - buffer set to the size of a single burst (83 bytes). Use auto-start, write a table and to stop after each entry to reset the task. Stable, but stop task slows down the program d ' attribute. Any way around this limitation?

  b. a continuous sampling, set buffer to a few thousand, writing of arrays of bytes-83 periodically - faster, but frequent buffer above/below runs under Windows for obvious reasons. Any way to stabilize? Maybe play with meter output instead of running all the time?

  Hey Fedor,

  Can quantify 'fast '?  This will help us to make suggestions to achieve your goal.  Take a look at the attached example VI because it uses a square wave generated from an analog output to trigger a redeclenchables counter.  These must be connected physically.  This impulse will be the sample for your output clock.  I hope this helps - let me know if you have any questions after test it!

• How to use the sony hdr-XR160 for a video stream live

  Im trying to use the Sony HDR-XR160 for a video live feed to the internet, but can't seem to find out if this is possible.

  The camcorder has HDMI and A / V output connections. Depending on your computer, you can connect the camcorder to a HDMI IN and A / V in port. Once connected, you can start streaming using the appropriate software. Please see the manual for more information on the available ports, you can use your computer operating.

  Please note that USB streaming is not supported by this unit.

  If my post answered your question, please mark it as "accept as a Solution.

• looking for usb driver for handycam DRC-trv16e

  looking for usb driver for model handycam sony dcr-trv16e

  Hi antmel,

  What is the operating system installed on your computer?

  The Sony DCR-TRV16E camcorder USB streaming feature is compatible only with Windows XP and earlier versions of Windows operating systems. For computers with Windows Vista and Windows 7 operating systems, an A / V or i.Link connection is necessary to transfer the videos from the camcorder. The i.Link connection may be used to transfer videos on Mac computers too.

• Computer doesn't see Sony DCR-HC96 camcorder connected by USB

  Running Vista Home Premium 32 Bit on DELL XPS 710.

  Impossible to stream video to Movie Maker, Adobe first Elements 3.0 when using the USB cable.

  All of the suggestions.

  Hello

   

  Thanks for posting the question in the Microsoft Community!

  The computer doesn't detect camcorder Sony DCR-HC96 .

  According to the Sony website, the USB streaming is not possible with this device.

  See the site:

  http://eSupport.Sony.com/us/Perl/support-info.pl?template=&info_id=544&MDL=DCRHC96

  I suggest you send a query on the Sony support site for further assistance:

  http://community.Sony.com/?XID=M:header:eSupport

  You can always follow the mentioned steps and check if the device is detected.

  The device cannot be detected if the drivers are not properly installed.

  1. What is brand and model computer?

  2 have you checked in the different USB ports?

  3. are you able to use other USB devices?

  To check if the problem is with the drivers, I suggest you follow the mentioned steps:

  Method 1:

   

  Run the fixit:

  Hardware devices do not work or are not detected in Windows

  http://support.Microsoft.com/mats/hardware_device_problems/en-us

   

  Method 2: Reinstall the USB drivers

   

  a. Click Start, type devmgmt.msc and press enter

  b. now under universal serial bus controllers, do a right click on a device and uninstall

  c. Repeat step secondary universal b for all serial bus controllers entry.

  d. now, restart the computer so that all drivers are reinstalled.

   

  If you need assistance or if you have problems of Windows in the future, let us know and we would be happy to help you.

• Hi, I have a camcorder Sony TRV 356 I am unable to connect on vista or windows 7 via USB

  Hi, I have a camcorder Sony TRV 356 I am unable to connect on vista or windows 7 via USB

  Hello Sajid,

  The community here is about the countries United States, Canada and Asia-Pacific. Your DCR-TRV356E model is a model British camcorder.

  However, to answer your question,.

  The DCR-TRV356E USB streaming function is not compatible with the operating system Windows Vista and Windows 7. You can connect the camcorder to the computer using the A / V cable connection or using an i.Link cable.

  You can visit the European Forums of suggestions regarding the transfer of videos to Windows Vista or Windows 7 computer.

  http://www.Sony.co.UK/discussions/community/en/support/cameras_and_camcorders

  If my post answered your question, please mark it as an "accepted Solution".

  Thank you for your message.

• Satellite a60-106 does not recognise handycam

  Hello
  I got my satellite for about a month and everything works fine but when I try to transfer video to my handycam I get an error on the screen of the camera saying "usb invalid during easy handycam" sony's site is all the answers. Other usb devices work fine.
  Any help appreciated.
  Thank you
  Barrie

  Hey Barrie

  If you have a specific problem like that he will always be interesting to know what external device will connect you to the laptop (with Sony). In my opinion, it is not a USB problem but a specific question. Usually in this case the producer of the outdoor unit must have an answer.

  I assume you are using the software given by cam. Check if there is some play/edit menu and the option of USB stream and assign him normally. Usually, it is set to off and the pc doesn't see the cam.

  Good bye

• The dsc-w710 camera can be used as a webcam

  The w710 dsc can be shown directly on a computer for the photo or video capture screen?

  Hi Paul-C! I understand that you want to use the DSC-W710 camera as a webcam. Unfortunately, this camera model has not a USB streaming feature. Once the device is connected to a computer via USB, it goes into data transfer mode and will not be able to save pictures or videos.

  It may be possible to view a "live view" of what the camera is the view using audio/video connection. However, the computer may need to other components of an audio/video input, video capture card and software for recording. This may be an alternative, but still not guaranteed.

  If my post answered your question, please mark it as "accept as a Solution.

• Live on Pc with handycam CX-210

  How can I send a live video on my pc with handycam Cx-210? I can transmit on my TV with an HDMI cable but I can not on my PC, you have a solution?

  Thank you

  Hi sany,.

  Welcome to the community of Sony!

  If I understand you correctly, you want to use the computer as an external monitor to your camcorder to see what you are recording live. Computers, especially laptops, has not the same HDMI port than a TV. Computer HDMI port only allows audio and video signals from the equipment itself, unlike television which has HDMI IN port.

  The camera doesn't have the USB streaming feature wherein you can use USB connection for you stream videos live online. You can only play the videos at the time when the camera is connected to the device or when you import the file to the computer.

  If my post answered your question, please mark it as "accept as a Solution. Thanks_Mitch

• Need software/drivers for the Cam MiniDV DCR-TRV25

  I have owned one of these great little cameras Sony miniDV since 2003 - in fact I love it so much, I bought a 'reserve' on ebay a few months ago.

  The problem is when my laptop crashed, I lost the initial load of the original factory driver for the camera software... and I can't find the original anywhere drive. None of my web searches have found links to reload the driver.

  Even more amazing, I started using Sony Vegas Movie Studio clean - but it plain refuses to import video from his OWN camera - saying that it does not recognize the device.

  What are my options and alternatives for this?

  NC to LB, CA

  Hello. For your computer to recognize the device, if it was recognized before, would mean that either your use of Windows XP or an older operating system. Unfortunately, USB streaming is not supported by Windows Vista, Windows 7 and Mac. But using a different connection: IEEE1394 (i.link or firewire) connection it should work with these operating systems. Going up that probably you just need to install the driver for the camera, you should be able to get it here:

  http://eSupport.Sony.com/us/Perl/SWU-Li... l = DCRTRV25

  Select your operating system from the menu drop down and download and install the device driver (Driver USB for Connection). Make sure that the camcorder is not connected to your computer while installing the driver. Follow the instructions below the USB driver for the login page properly install the driver. Restart the computer and connect the camcorder. Complete the installation of new hardware found. Also make sure that your camcorder USB Stream function is set on IT. Use the application pre-installed Windows Movie Maker or compatible video capture software to capture video to off the Strip. I hope this helps.

• Windows 7 and DCR-HC21

  I have a Sony DCR-hC21 camera and laptop computers changed recently. I now run Windows 7 64 bit. I can't download drivers for the PMB software. Is there another way to transfer a movie from the camera to my laptop?

  You cannot use the USB cable because there is no USB streaming of drivers for windows 7. Camcorder came with SW called Picture package. Not compatible with windows 7. PMB on esupport are updates only. Cannot use this. Check if your computer has an IEEE1394 port. If that's the case then you can use an i.link cable, known as a Firewire cable as well. No special SW necessary with this cable. Your computer will automatically use Windows live movie maker to capture video. If the computer lacks the IEEE1394, then you can use the A / V cable supplied with your handycam. Use of the A / V cable you will need to get an external A / V capture card that would receive signals of the handycam and pass them through a USB port on your computer. Check the Dazzle for example: http://www.pinnaclesys.com/PublicSite/u... ts/Dazzle /

• Handycam dcr-hc26 wouldn't work on windows 8

  I just bought a new computer with windows 8. I got the camcorder (DCR-HC26) for awhile now. When I treid to operate on my new computer, cannot do. I have search and treid everything. The accompanying cd will not work on windows 8. I downloaded PlayMemories, still nothing. Can someone please. I'll be very angry if I can't get this working on windows 8. I have a lot of taps.

  Hi Todd,

  The community here is a way to connect, share and help each other with a variety of topics. We as moderators are doing our best to intervene when the community has failed for a few days. However, if you need immediate assistance or an answer right away, we strongly suggest you contact Sony technical support for a quick and direct answer, either via chat or by phone by clicking here:

  http://eSupport.Sony.com/us/p/support-contacts.pl?MDL=DCRHC26&loc=3

  To answer your question, this camcorder USB Streaming feature is not possible with Windows 8 operating system. If you try to connect the camcorder to your computer Windows 8 using a USB cable, the camera will not be recognized by the computer.

  To transfer the videos from the camcorder to your computer with Windows 8 operating systems, use an i.LINK (a.k.a firewire or IEEE1394 cable) cable or Audio/video provided (A / V) cable and software compatible video capture as Windows MovieMaker software.

  According to the availability of the iLINK decision-making or A / V jack on the computer, follow the instructions provided in the links to transfer the videos below.

  i.LINK cable:

  https://us.en.KB.Sony.com/app/answers/detail/A_ID/37892/p/36919, 37620,37639/c/65,66/kw/transfer%20vi...

  Audio/video (A / V) cable:

  http://eSupport.Sony.com/Tutorial/389/us/en/

  Once you have transferred the videos on your computer, you can use the software PlayMemories home (WPH) to organize the video files.

  If my post answered your question, please mark it as an "accepted Solution".

  Thank you for your message.

• using DSC-W350 as webcam

  How am I able to use my Sony DSC-W350 camera as a webcam? I have the selected video mode and its plugged into my Vaio. Do I need other software?

  To use a digital camera as a WEBcam, the camera must have USB streaming mode. This camera photo and all the sony Cybershot cameras are not designed to use a webcam.

• Sony Handycam

  Hello

  I have a Sony DCR-HC40E and I want to transfer video from tape to my computer and my Lenovo Windows XP with the USB cable, but the ability to import the video does not appear, I tried to reboot, but still no success.

  Please notify

  You must first activate the USB streaming camcorder. On the screen of the device, please press [P-menu] - [MENU]. Then, scroll to the [STANDARD SET] key and press [OK]. Scroll down and find [USB-CAMERA] and select [USB STREAM].

  Once this is done, you can now connect your camcorder to the USB port on your computer. You must use a video capture software, such as Windows Movie Maker and record the video as it is being played on your computer. Please refer to the operating instructions of the software that you will use for more information.

  Please note that these steps apply only to a Windows XP computer. Recent operating systems no longer support the camcorder's USB streaming function.

  If my post answered your question, please mark it as "accept as a Solution.

• Handycam DCR-HC20 questions

  My wife has a Sony Handycam DCR-HC20. We have a laptop of Dell Latitude running windows 7. We tried to show and transfer videos recorded on the Handycam to our computer. So far, the computer does not recognize the camera when I try to add. My wife said that she had a drive to intall the software to the computer when she got the camera, but she got several years ago. Is there a driver or a way to display the records from the camera to the computer?

  Hi Clayton,.

  Welcome to the community of Sony!

  The drivers needed to connect the camcorder to Windows 7computer and transfer files are already included in the operating system. However, the USB streaming feature is not supported with the Windows 7 operating system. You can connect the camcorder using either A / V or i.Link cables can transfer video. Instructions to transfer video using A / V and i.Link cables are mentioned below.

  How to transfer video to a computer via an i.LINK connection

  How to transfer video to a computer with Audio/video (A / V) cables

  If my post answered your question, please mark it as an "accepted Solution".

  Thank you for your message.