HPe 1170t CTO: 1170t

Similar Questions

• Update the bios HP Pavilion Elite HPE - 480t CTO Desktop PC

  I just bought a hard drive 3 TB to my HP Pavilion Elite HPE - 480t CTO and he only sees a drive 746,52 GB under Windows 7 pro 64 bit. My main drive is a 1.5 to and he sees very well. where can I find an update of the BIOS using the new drive? I have been to the page "downloads of software and the driver" and it does not list one. Am I out of luck?

  When I ran Paragon booted from a USB stick to copy my 1.5 TB drive it given the disk as a disk of 2.7 to so I think the bios is seening it?

  EDIT: The Intel rapid storage technology software sees as 2 862 TB, but windows doesn't see 746,52 GB.

  Thank you

  Curtis

  Solved!

  Update card mother sata drivers and program "Fast storage Intel technology" and it now works fine.

  Went to ma-configdotcom and ran their detection app and it recommended JMB36X_WinDrv_R1.17.65_WHQL_eSATA.zip of JMicron and Intel's SetupRST.exe. I ran both, restarted the computer and viola! He works and see all the new drive.  I hope this helps someone else.

• USB 3.0 card desktop Pavilion Elite HPE - 390t CTO?

  Is there a HP (or other) 3.0 card USB compatible with the Pavilion Elite HPE - 390 t CTO desktop PC?

  Thank you.

  Hello

  Your product, it seems that you should have enough space to expand.

  I suggest you find a USB 3.0 PCIe card to any provider of computer frame.  Here are the instructions on installing a PCIe card (you can start with step 2).

• HP Pavilion Elite HPE-400z CTO: HPE-400z S/PDIF

  I need best plug to the motherboard of the HPE-400z system.  I need to the rider in a video card and the document online say it is an internal port but nothing describes where it is.

  Help, please.

  Hello

  See the image below.

  

  The SPDIF connector has been used with older graphics cards to route the audio signal to the output from the HDMI connector.

• HP Pavilion Elite HPE - 400z CTO: H - RS880 - Μatx Motherboard BIOS Update caused crash, to see a black screen now?

  I have a desktop HP Pavilion Elite HPE-400z running Windows 7 (64), my computer was working fine, however I thought that I needed to update the drivers and things from the HP website.

  The first thing I installed was the following: H - RS880 - Μatx Motherboard BIOS Update

  That restarted immediately frozen mouse on a black screen. When I turn on the computer the lights and the fan turns on but the screen remains black. Their is nothing wrong with the monitor, it's light is on, but when turn light it just says: "monitor going to sleep".

  I went through these troubleshooting pages: http://support.hp.com/us-en/product/HP-Pavilion-Elite-HPE-Desktop-PC-series/4269972/model/4300925/do...

  http://support.HP.com/us-en/product/HP-Pavilion-elite-HPE-400-desktop-PC-series/4269972/document/BPH...

  without success.

  Any other suggestions of what I could do to fix this?

  Hello

  Disconnect the PC and press and hold power for 30 seconds. Remove and replace the battery CMOS. It's a $4 item. Now let's see what happens. If no joy, then try the steps above once again.

  If your PC support has been changed or modified then put it back in its original state.

• How can I activate the boot usb for my HP Pavilion Elite HPE - 480t CTO desktop PC?

  I have a usb key with the Windows operating system installed. But I could not find a way to get started on the drive on my hpe - 480t.

  Any suggestion?

  Thank you

  Wayne

  NVM. I can boot from a USB on the computer.

• HPE-490 CTO: Failure USB 3, port 0

  Suddenly, one of the USB 3.0 on this host ports doesn't work.

  Is it possible to check his status (not obvious outside the cosmetic problems

  or connector problems)?

  Re-enable?

  Replacement?  This USB adapter has been installed HP purchase.

  Thanks, is mwh

  Try to remove the USB expansion card and then install again in the same dwelling and retest. If this does not help, try one of the other available PCIe slots.

  If there is still no change with the issue, then this is probably the card itself that has the problem.  In this case, please use the following http://www.hp.com/contacthp, fill in the form, create a folder for your question, and then use the information to contact HP.

• HP Pavilion Elite HPE - 480t computer and burner blu - ray 12 x HP bd 340i

  Model bd340i in the middle of last year, I bought HP 12 x Blu - Ray burner. When I bought my HP Office in December 2010 model HP Pavilion Elite HPE - 480 t, I installed the burner and everything worked very well. Today, I tried to burn a blu - ray disc, and he returned with can't read media, which stood on imgBurn. So I tried the same thing on the burner systems, and she came back as no drive in the status bar. I have also tried burning CyberLink software and the same thing no disc.

  I then tried to play the two store bought and home made blu - ray disc and could not read media. I was ready to blame it on a bad burner but then I tried a regular DVD the two store bought and done House, and it plays very well. I then tried to burn a single dvd double layer with all the burning software three I have and it is still fine, no problem. It's just the blu - ray media that cannot be read or written. The only supports blu - ray, I used from the first day was Kodak and never had a problem. That's what baffles me.

  At this point, I don't know if it's a hardware or software problem with the computer or burner blu - ray or both. 3 different burning programs works fine on DVD but not blu - ray, DVD plays fine but can't play or burn blu - ray discs.

  Could this laser blu - ray crapped out and the dvd reading and writing laser still works?  Must a blu ray burner still lasers for both media (DVD and Blu Ray)?

  Everything else with the computer works fine. I even tried uninstalling and reinstalling and it is the same, I tried to update the drivers and firmware on your site and still does not work. Please help.

  When did you purchase your product? : December2010
  Product HP Pavilion Elite HPE - 480t CTO desktop PC
  Select a problem area: other
  What is your serial number (SN): [personal information deleted]
  What is your operating system? : Microsoft Windows 7 Home Premium 64
  Your computer is unable to work with Accessories products? Please select all the boxes. other
  What type and brand of CD/DVD media you are using? Kodak 25gig of Bu-Ray and dvd HP
  The CD/DVD writer burner was built in the computer when you bought it? NO.
  You hear the sound from the speakers connected?
  The display on the product seems to work correctly? Yes
  Have you connected the product to your TV, DVD player or a music system? NO.

  If there is an error message, please specify: cannot read media
  Description of the problem: I bought burner HP 12 Blu - Ray model bd340i in the middle of last year. When I bought my HP Office in December 2010 model HP pavilion Elite HPE - 480 t, I installed the burner and everything worked very well. Today, I tried to burn a blu - ray disc, and he returned with can't read media, which stood on imgBurn. So I tried the same thing on the burner systems, and she came back as no drive in the status bar. I have also tried burning CyberLink software and the same thing no disc. I then tried to play the two store bought and home made blu - ray disc and could not read media. I was ready to blame it on a bad burner but then I tried a regular DVD the two store bought and done House, and it plays very well. I then tried to burn a single dvd double layer with all the burning software three I have and it is still fine, no problem. It's just the blu - ray media that cannot be read or written. The only supports blu - ray, I used from the first day was Kodak and never had a problem. That's what baffles me.
  Please provide previous steps of troubleshooting, or information that can help HP help you. : I don't know at this point if it's a hardware or software problem with the computer or burner blu - ray or both. 3 different burning programs works fine on the DVD but not blu - ray, DVD plays very well, but can not play blu - ray.
  Nothing changed since the device was working properly (installation of SW, settings, wiring, etc.): everything with the computer works fine. I even tried uninstalling and reinstalling and it is the same, I tried to update the drivers and firmware on your site and still does not work. Please help.
  How would you describe your level of technical skill? : intermediate
  First name Peter
  Name, first name rider
  [Personal information]

  Arcticwolf, sorry, I miss read your post details. That strangely resembles a failed drive. Try unistalling and reinstalling the drive, including the software and driver. If a problem has occurred, it may fix.

• Questions about the video card upgrade

  I have a t HPE-310 (CTO) with an Intel i7 processor and an AMD/ATI HD5450 graphics card.

  http://h10025.www1.HP.com/ewfrf/wc/product?product=4242292&CC=CA&DLC=en&LC=en&JumpID=reg_R1002_USEN _...

  I want to upgrade the graphics card to better manage the Guild Wars 2.

  I am looking to buy an AMD/ATI HD6850 and a CS600 Corsair for power.

  Is this a reasonable combination for my computer? Are there other combinations you would sugget instead?

  Also, there are other problems, I need to be careful?

  SteveW44,

  If you meant the CX600 Corsair, I anticipate no problems. Enjoy!

• Want to improve my diet for a new video card; have any questions.

  Wishes of the members of the Forum;

  I have a PC HP Pavilion Elite HPE - 190t CTO Office purchased in March 2010.  Very good product, but food is not fit to what I run.

  I have purchase a Corsair 650TX so I can run an EVGA GTX 680.  This requires a minimum of 550W and dedicated a 35Amp 12V line.  All this has the Corsair.

  I started with the information on the site of HP support on how to install a new power supply.  Followed the instructions.  Replaced my PSU 460W.  Tried to turn on my computer.  Power through the system, but it seems the cord for the APX CPU is slightly different or does not work.  Can not tell what is happening. The device seems to be functional, but it is possible that the CPU 12V cord is bad.  I'm not sure.  If this is compatible with my computer, I'm missing something.  I've updated the BIOS, also upgraded to professional Windows.  It feels like it could work almost, that somehow I'm missing just something.

  Clues.

  Thank you

  Hello

  Try to clear the CMOS memory.  He worked for a person at the time when changing the PSU.

  If the above does not work then check your connections and watch to see if the fans are running and you don't not knocking something loose.  The FAQ above have a test procedure for power supply, you might want to try.

  Finally, try the old power supply.  If it works then you probably have a bad power supply.  It is rare, but it happens to all manufacturers of power supply.

• HP Pavilion HPE h8 - 1380t CTO: compatibility problems, ask questions about knitting-by-turn or possible motherboard replacement.

  I recently baught an EVGA GTX 1060, as this 630 became quite long in the tooth and I thought that I would try to future proof myself a little as the rest of my components seem to be working very well.  However, I can't get the map to work correctly on this particular computer.  Oddly enough, I can get past that screen startup finally after several short beeps and let it sit, but it takes fowever to reach the office and clearly is not executed properly that the resolution is wobbly and software from Nvidia cannot even detect the card.  I guess I had got this far because of the onboard graphics of some sort, but AFAIK this motherboard which lacks.

  I know that the card works fine as I tested it in my other Tower, so I struggled to find a solution.  So far, it seems that the problem is most likely the motherboard, as HP does not have a new BIOS for it since the beginning of 2013 (which I did go ahead and install it).  If true, I find myself with either two options, it seems that the ditch system, entirely or find a motherboard that works with all my old components.  I'd rather not have to empty this workaholic, when all other parts work great, if it is not a work around I would like to know if there are motherboards I could pass that would work with the rest of my components.  Normally I would not bother with even apply for, but I hear a lot of chatter on HP PCs pre-constructed having compatibility problems.

  I bought this computer there is in the case of four years that I would be able to update as I do with any other PC, but I didn't know at the time that HP has a tendency to not update the BIOS settings for anything beyond a year which I admit is incredibly frustrating.  What is done is done however, and I want to make this work without having to clear the entire system.

  Desktop HP Pavilion HPE h8 - 1380t CTO

  Model #: B4J28AV
  Serial number: 2MD2290502

  Motherboard: 2ACE "Pittsburgh" Pegatron Corporation

  Processor: Intel Core i7 3820 3,60 GHz 'Sandy Bridge - E.

  RAM: 10 GB of DDR3 memory

  GPU (stock): Nvidia GeForce GT 630 (this is replaced by the EVGA GTX 1060)

  @Faver, welcome to the forum.

  Your problem is the BIOS.  However, it is because the 1060 GTX requires UEFI in the motherboard instead of a standard/Legacy BIOS.  HP didn't start using UEFI until mid-October 2012.  The BIOS may not be upgraded in the UEFI.  The last cards only not for UEFI were the GTX 660/670.

  MSI made cards with a switch that can be used with a Legacy BIOS or UEFI.  If you decide to go this way, you must contact their Technical Support to help them choose the best card for your system.

  The upgrade of the motherboard can be a problem.  HP has taken advice their specifications.  Therefore, they are not necessarily the same as the commercial versions.  Please make sure that the holes in the motherboard matches the accessory in the case.  In addition, some members have had problems with the connectors in the connections case before, for example, the power button.

  Please click on the button + Thumbs up if I helped you and click on accept as Solution If your problem is resolved.

• HPE h9 - 1110t Phoenix CTO: Questions about change of graphics card

  Hello, my computer is a HP Pavilion HPE h9 - 1110t Phoenix CTO desktop PC. I think it's time to replace the graphics card, it's come up with, the GeForce GT 545. Lately my performance in games such as Star Wars The Old Republic has considerably decreased in FPS and it stutters terribly while he was playing even on the smaller settings. The fan is really loud when the games. And in the past two months, I got two random reboots, which gave rise to a video as material error being the cause. The fan blades have a lot of dust between the two, but they are so small and placed together, I can't clean it good.
  
  I have an EVGA GeForce GT 640 to replace. But I have a few questions first. This card is compatible with my motherboard, right? Second, before installing it, should I uninstall the drivers I have right now for my 545? If so, I then stop and put the new? And after that I put in, the resolution will be all twisted up until I have install new drivers? And should I install the drivers from the NVIDIA site, right and forget the CD?
  
  Also, I have a 600w PSU, fake? That's what the specs say on HP for my computer, so it's going to be enough to have the right to TG 640?
  
  And then, about my diet, I want to get dust inside of it, but I won't come out or open or other. I saw on the site of HP I can take a vacuum and suck the dirt out of the outside vent. Can I do this without damaging it? I have a vacuum in my garage from Sears, I got that I use to clean my car, which would be allowed to use on the outside vent?
  
  Thank you for the answers!

  GT545 (75W) and 640 (65W) are only 10W difference.

  Uninstall via the Device Manager.  I always liked create a new installation with the latest software and driver CD. If you wish, use the old CD. That will be established. It will update.  If you use a shop vacuum, keep the nozzle in contact with the metal frame. I like the nozzle between 2 fingers from the cradle.

• HP Pavilion HPE 1090 t: could someone help me please... Desktop HP Pavilion HPE h8-1090 t CTO - PSU replacement/compatibiliy

  I just bought a new power supply (Corsair CS650M) because someone has suggested that it would be a good replacement power supply for my HP model which is HP Pavilion HPE 1090 t.   I need to know if this Corsair works and is compatible with my system, because something is not working with him directly or I did something wrong.    This is my first install and when it comes to the ins and outs of power amplification entry & exit and amperages I get so confused about this stuff.   But I think I took all the pluged connection correctly, at least when I re-plugin my old PSU after the installation to fail, I had the PC working again, what made me give confidence that I did the Corsair install correctly.  But what happens is after the installation of the unit from Corsair and turn the system he clicked power off after about 10 seconds or more and then restarted after a few seconds, then stopped again and turns off after another 10 to 15 seconds, and nothing would come up on top of the screen no more.   The first time I did the research what PSU would be compatible, I was getting conflicting results with a few places on the net saying that the majority of the HP out there (excluding some models such as the slimline) could be replaced by different manufacturers and higher power PSU, while other places I looked different.   Even the person who recommended me this power supply said in his post that he installed a Corsair HX650 model in its HP PC, and it worked very well for him.  Now, after the failure of the installation for the next few days, I did a lot more research and when I went on the site of HP and looked up the specifications of the model my PC I noticed under the power supply section, he had a heading that says "must select one of the following options" (in fact most of the different sections shows that the title too) and then he showed only two options 460W and 600W.  Then he asked me if it's the only option I get with my model.  And then I looked at my model number HP on the HP PartSurfer and under the section of the PSU, it also registers only 460W and 600W.   So who is?   I have to stay with only these options two HP or can I get a power supply with a higher power a bit then 600W from a different manufacturer that is what I want.    If I can get something that is compatible other than the options listed HP please let me know, or if this Corsair should work someone please let me know.   I need to return it otherwise.    My specs are below.

  Thank you Aaron

  HP Pavilion HPE series
  Model No.: h8-1090 t CTO Desktop PC

  Name motherboard manufacturer: IPMTB-TK Pegatron HP/Compaq name: Truckee

  PIC of the motherboard link: http://support.hp.com/us-en/product/HP-Pavilion-HP E-h8-1000-Desktop-PC-series/5080764/model/5117795...

  Original HP installed: AMD Radeon HD 6570 (Bronco) graphics card 1 GB Model: 648533-001, SP # 659355-001

  Link video card PIC: http://www.ebay.com/itm/111761368505

  Nothing has been added/modified recently real system.  Last change was the beginning of the year 2015, which was a new 2 TB HDD and added however problem memory only started about 3 weeks ago.  The Interior has been cleaned (diffuse can)

  600W Μatx Estar v5 HF PSU (Petrus)

  Information about the current hardware out of the Power Supply Unit

  Switching power supply
  Model: DPS-600WB A
  Part number: 633186-001
  600W power MAX

  Output: DC output rating (new Corsair PSU)

  + 12Va = output DC 16A = + 3.5V / + 5v / + 12v /-12v / + 5vsb

  + 12Vb = 18 a Max Load = 25 a / 25 a / 51 / 0.8 a / 3a

  + 12Vc = 12 a Max comb = 130W / 612W / 9.6W / 15W

  + 12Vd = 10A power Total Power 650W

  + 16 5.08V = side of AC input

  + 3, 3V = 15 a AC input: 100V - 240V

  + 2 5.08Vsb = current: 10A - 5A

  -12V = 0.3 frequency: 47 Hz to 63 Hz =

  Entry:

  100-127V ~, 50-60 Hz, 10 a

  200 - 240 v ~, 50-60 Hz, 4A

  You are welcome.

  Although there is a limit to the amount of power that is needed to power your computer, it uses only the amount of power it takes to power the computer correctly.  The extra power is kept in reserve for the purposes of art.  Thus, you cannot really bad the computer with extra power or amperage.  You can sleep on this point.

  Indianaak wrote:
  

  Thank you very much for your quick response, I wasn't getting anyone to answer the previous post.

  If your saying these HP spare parts are not exclusive to the company?  Some connectors may be owners, but most are not.

  It should work then?  Yes.  I've recommended hundreds of the PSU in the years I've been helping on the Forums; in fact since about 2002.

  How about the input/output & amperages of note that I registered?  As I understand not all this jargon, I want to assure you that I have / using correct notation for my system.  I don't want to fry one of my compondents with to much amperage.   Well, either I did something wrong installing or this power supply is a dud then.  Read my explanation at the top of the page.

  As I said before I pretty sure I had all the right connections, what can you tell me if it sounds right for you.  I have pluged in both connectors wired on the motherboard which were the main ATX 24pin power connector and the EPS/ATX12V 8 pin which I shared and pluged a piece of the cable labeled 'CPU' in slot 4 pins on the montherboard labeled ATX CPU.  Regarding the other split 4 pads, I don't see anywhere, it could be pluged into the motherboard.  If two 4-pin connectors were even marked, it should be good.  However, you can try to plug the other 4 pin instead of this, just to make sure that the right pair is connected to the processor power.

  My AMD Radeon HD 6570 1 GB graphics card is the type that is fed through the MB so I didn't use any of the PCI-E cables 6-8 poles.  It is very good.

  And so the only thing I had left that I have pluged the compondents of Sata cables that was my Bluray burner, my 2 TB hard drive and my USB 3.0 card.  They are very frank.

  Yet once again being installation of hardware in my system let me ask hopefully not a stupid question, but when you connect compondents Sata cable, you must have the plug-in in a particular order of wiring compondent or how do you?  I don't check the specifications of your power supply, but I think most of them have a single 12V rail.  If this is the case, you don't have to connect them to any order.  If there are two rails, it is best to divide the power of each rail.

  On my old PSU, it has an extension cable SATA used to connent card USB 3.0 which is pretty tightly squeezed between graphics card and sound card, so I guess I could use the extension cable with the new PSU POWER Sata wiring without any compatibility also publishes, right?  This should be no problem I can think of at this point.

  Thanks again for your help, I'll probably will try and plug it once more and see if I can make it work.  If this does not work for now, I strongly suggest that you contact Technical Support of Corsair for help.  They are the experts on their products and grab any errors that we do.  It is very difficult to diagnose a problem by far.  When you have done with this project, you will no longer be the excuss you are a novice. You will have a lot of knowledge that you did not when you started.

  Please click on the button + Thumbs up if I helped you and click on accept as Solution If your problem is resolved.

• HP Pavilion HPE h8 - 1070t CTO need case fan

  HP Pavilion HPE h8 - 1070t CTO, product number: LP028AV #ABA

  After an error message, on the fan and case fan noise I replaced the AVC DS09225R12MC234 DC 12V case fan 0. 3A with a Startech.com FAN9X25TX3H case fan.

  A program to monitor I have shows an increase in rpm of the system another fan. I'm trying to find out if my new fan is correct or adequate propper case fan.

  Hi checkit, as long that all fans are working and they doesn't make unusual noises or work allways on the maximum RPM is fine, Adi.

• HPE180T CTO: HPE 180 t graphics card advise?

  Recently, I improved my diet at 650W, installed a 660Ti GTX card and had nothing but problems. I did everything as suggested here and elsewhere. I updated the Bios, used DDU, reformatted and reinstalled my OS. Tried on older drivers, the most recent, etc. I am a real novice, but is not afraid to try things.

  The only thing that I didn't call HP. Maybe I should have. In any case had graphics driver stopped responding and has recovered the message a lot. Of more the black screens, blockades, without starts, blue screens.returned the 660Ti. I reinstalled my original raedon 4650 and no problem except once, using only a Topaz Labs don't branch I got the error message driver graphics. My question is that I would be able to go to any more recent card without problems? Is there a certain class or number of my motherboard?

  I need a card with Open GL of at least 3.5 to run some plugins. My current is there, but I need a better performer. Then my monitor is causing a problem? Its a PH Dell 2012 H, which is not a high resolution, screen play. (1600 x 900), I asked some questions here before and got a lot of help, but nothing seems to work, and I don't want to buy a new card to have the same problem. Big Dave said he ran the 660Ti in a similar unit with no problems. I spent about a week of reading and trying things. Comments or suggestions?

  I7 [email protected] HPE 180 T

  14 d

  Win7pro

  Raedon 4650

  When you try to upgrade a computer 6 years with newer components, it is difficult to know what will work.  I suggest you contact EVGA Tech Support (1-888-881-3842) to get an idea of which of their video cards will work with your system.  They have always been very helpful whenever I got in touch with them.  I have no doubt they will give you good ideas.  Personally, I don't want you buy a map on my advice and pay to return it.

  Please click on the thumb top + button if I helped you and click on accept as Solution If your problem is resolved. < br >