HS and gateways

Similar Questions

• Laptops acquire wrong address DHCP, DNS and gateway wireless

  I have problems with two laptops. For some strange both acquire the bad DHCP, DNS and gateway (server) respond when I try to access the Internet via Wi - Fi. For some reason, this does not happen when I use the LAN (cable) connection.

  that is instead to fetch the address: 133.24.56.78 (no real address), the system retrieves / uses 111.22.33.44 (again, not a real address). BTW, these two systems are configured to fetch automatically get IP addresses and DHCP. I tried to fix the connection in both cases, but it did not work.

  What can I do to fix this?

  Problem solved.

  I changed the router to WEP (WPA - PSK) encryption.

• NB200-h-13 - no response from the DNS server and gateway

  Hello

  I have netbook NB200-h-13 with XP SP3. Its impossible to connect to wireless internet and the error messages are
  HE DIDN'T THERE WAS NO RESPONSE FROM THE DNS SERVER
  HE DIDN'T THERE WAS NO RESPONSE FROM THE DEFAULT GATEWAY

  The connection with the ethernet cable is ok with the adpter reltek that also adpter atheros ar9285 WiFi is activation, working properly and the modem router signal is strong.

  Hi abk55,

  What program you receive this error message?
  Have you tried another browser, for example Firefox or Opera?

  I guess it has something to do with your wireless network card or WLAN parameters if the LAN cable is working properly. So you should try to update the WLAN driver on the Toshiba site.
  Also, try to disable the filtering of MAC addresses and use another encryption.

• TestStand and Gateway requirements

  Hello

  It is more a question of RG, but there is no RG area to post.

  I have a Word Document that defines the requirements for a test sequence.

  Needs are covered by the two

  (1) LabVIEW VI

  (2) sequence TestStand.

  What I want to do is to see what is my coverage of the coverage of Word Documents.

  I noticed that when I added the TestStand sequence for my gateway Req project, all entries in the TS document generates a "derived demand".

  Is there a way to turn off?

  I want to connect my word document to a place in the test sequence and to say that this is where I cover that is recording data. I don't want to link my TS sequence with a results file.

  The annoying bit is when I look at the view analisys even if my Word Document is covered at 100% yet there are a number of requirements derived from the sequence of TS discoveries.

  Thanks for the tips!

  Maciej

  Maciej salvation,

  answer your questions:

  (1) connecting a TestStand sequence to a Word Document causes RG generate the "derivatives"requirement for each of the elements (steps or sequences) TS.»
  I would like to cut this robot. I'm not interested in the requirements derived in this scenario.

  "You can turn that they derive ar requirements shown by selecting view" derived from the requirements in main menu of th.  This will hide the requirements derived from the view and in reports that you generate.

  (2) Assembly of the desired structure

  If you link the arrows of cover in the Middle, you can create a relationship "or", as shown below.  In this case, a requirement is considered covered when it is covered by one of the 2 on the documents.  The configuration that you currently expects that all THE accompanying documents have coverage for each requirement.

  

  For more information, see the topic combining covering links in aid of the gateway requirements for more information.

  Let me know if you have any other questions!

• IPAddress and gateway settings problem

  We connect tv (panasonic with Viera link function) to the internet by cable and by sector. Have just got new computer and cannot now, t connect to the internet on television. »

  What research of connection, it is said cannot find the ip address. I have found information of ip address on the computer and added only manually. The search came then to the problem with the gateway. Entered amendments. for the gateway, but that didn't work - any suggestions?

  Hi Sue,

  Thanks for choosing Microsoft community.

  I can understand that there is problem (Panasonic TV) connection, but I see that your computer works very well on the internet. I think we should check the setting of the TV or call the internet service provider for assistance. When it comes to a network, default gateway will be the same, however, is different from the IP address of a device. Please refer to the operating manual provided by panasonic for assistance.

  To set up your TV, you can contact Panasonic.

  http://www.Panasonic.com/in/support/contact-us.html

  Alternatively, you can contact your internet provider for assistance.

  Hope this helps, please contact us for assistance.

• Modem cable and gateway Question?

  We set begin to use a new supplier of internet services by cable. This provider requires you to use their modem. My question is, 'We already have a LinksSys WCG200 cable gateway', will be able to simply use the router function of cable without the built-in modem gateway? Or would have to go buy a separate router?

  Thanks in advance.

  WCG200 doesn't have the Internet port where you can connect the cable from the cable modem Ethernet.

  Then, I suggest you to go to a separate router.

• FSX SP1 causes aircraft to turn blue and gateway is not responding

  After you install the SP1 update... I met problems with color graphics... some aircraft blue and when parked at the gate... CTRL + J is no longer active the boarding bridge. This is to keep in touch with updates... Do I need to uninstall and reinstall MS FSX as in some other cases read here?

  Jim C

  Hey Gringo Latino,

  1. you receive error during the game?

  2. meet the question only during the game on the computer?

  Usually, this will happen if there is a problem with the graphics card from the computer.

  I suggest that refer you below Microsoft articles and try the steps mentioned, check if it helps.

  Solving graphic problems in Flight Simulator X

  http://support.Microsoft.com/kb/925722

  Troubleshoot display with Microsoft games

  http://support.Microsoft.com/kb/263039

  I hope this helps!

  Halima S - Microsoft technical support.

• Connection to remote desktop using proxy and gateway desktop remotely?

  I have setup a gateway desktop remotely using Windows Server R2 2012 server. I use Remote Desktop gateway as an intermediary between to offer remote desktop session more than 443 because 3389 is blocked in several places of the customer.

  However, I encountered a problem with a customer that the network seems to use a web proxy.

  Is is possible to set up remote desktop to connect via web proxy? If so, how? If this is not the case, does anyone have any suggestions on how to provide a remote desktop session through 443 on proxy for situations where you don't control the client PC or network? RemoteApps allows access through the web proxy when you use Remote Desktop gateway?

  The error message is below to:

  Your computer cannot connect to the remote computer because the web proxy server requires authentication. To allow traffic not authenticated to a desktop gateway server remotely through your web proxy server, contact your network administrator.

  Thanks for any help!

  Hello

  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the TechNet Forums.

  TechNet Forum
  http://social.technet.Microsoft.com/forums/Windows/en-us/home?category=w7itpro

  Hope this information helps.

• Guest os ipaddress, subnet and gateway information

  Hello

  Can someone correct me the script below...

  &{foreach($vm in (Get-VM)){
  $vm.ExtensionData.Guest.Net |Select
  @{N="VM";E={$vm.Name}},
  @{N="Host";E={$vm.VMHost.Name}},
  @{N="OS";E={$vm.Guest.OSFullName}},
  @{N="Tools";E={$vm.ExtensionData.Guest.ToolsRunningStatus}},
  @{N="NicType";E={[string]::Join(',',(Get-NetworkAdapter -Vm $vm | Select -ExpandProperty Type))},
  @{N="VLAN";E={[string]::Join(',',(Get-NetworkAdapter -Vm $vm | Select -ExpandProperty NetworkName))},
  @{N="IP";E={[string]::Join(',',$vm.Guest.IPAddress)},
  @{N="Gateway";E={[string]::Join(',',$vm.ExtensionData.Guest.IpStack.IpRouteConfig.IpRoute.Gateway.IpAddress )| where {$_ -ne $null}},
  {
  foreach ($iproute in $vm.ExtensionData.Guest.IpStack.IpRouteConfig.IpRoute) {
      if (($vm.Guest.IPAddress -replace "[0-9]$|[1-9][0-9]$|1[0-9][0-9]$|2[0-4][0-9]$|25[0-5]$", "0" | select -uniq) -contains $iproute.Network)
      }
      }
  @{N="Subnet Mask";E={
              $dec = [Convert]::ToUInt32($(("1" * $_.IpConfig.IpAddress[0].PrefixLength).PadRight(32, "0")), 2)
              $DottedIP = $( For ($i = 3; $i -gt -1; $i--) {
                      $Remainder = $dec % [Math]::Pow(256, $i)
                      (                        $dec - $Remainder) / [Math]::Pow(256, $i)
                      $dec = $Remainder
                  } )
              [String]::Join('.', $DottedIP) 
          }},
  @{N="DNS";E={[string]::Join(',',($vm.ExtensionData.Guest.IpStack.DnsConfig.IpAddress))}},
  @{N="MAC";E={[string]::Join(',',$vm.MacAddress)}}
  }
  }
  }
  }
  }
  
  
  
  

  Try like this

  & {foreach ($vm in (Get - VM)) {}

  $vm. ExtensionData.Guest.Net | Select - property @{N = "VM"; E = {$vm. Name}},

  @{N = 'Host'; E = {$vm. VMHost.Name}},

  @{N = "OS"; E = {$vm. Guest.OSFullName}},

  @{N = 'Tools'; E = {$vm. ExtensionData.Guest.ToolsRunningStatus}},

  @{N = "NicType"; E = {[string]: join ("," (Get-NetworkAdapter - Vm $vm |))} Select-Object - ExpandProperty Type))}},

  @{N = "VLAN"; E = {[string]: join ("," (Get-NetworkAdapter - Vm $vm |))} Select-Object - ExpandProperty NetworkName))}},

  @{N = "IP"; E = {[string]: join (",",($vm.)} Guest.IPAddress | Where {($_.)} Split(".")). {{(longueur-eq 4}))}}.

  @{N = "Gateway"; E = {[string]: join (",",($vm.)} ExtensionData.Guest.IpStack.IpRouteConfig.IpRoute | % {if($_.) Gateway.IpAddress) {$_.} Gateway.IpAddress}}))}},

  @{N = 'Subnet mask'; E = {}

  $dec = [convert]: ToUInt32 ($(('1' * $_.))) IpConfig.IpAddress [0]. LG). (PadRight (32, '0')), 2)

  $DottedIP = $(pour ($i = 3; $i-gt-1; $i--) {})

  $Remainder = % [math] $dec: Pow(256, $i)

  ($dec - $Remainder) / [math]: Pow(256, $i)

  $dec = $Remainder

  } )

  [Channel]: join ('.) (', $DottedIP)

  }},

  @{N = "DNS"; E = {[string]: join (",",($vm.)} ExtensionData.Guest.IpStack.DnsConfig.IpAddress))}},

  @{N = 'MAC'; E = {[string]: join (",", $_.)} MacAddress)}}

  }

  }

• VLAN in environment ESXi5 Switch Cisco SG300 and gateway RV220W

  Hi, I'm having a few problems getting VLANing to work properly.  I was hoping that someone would be able to point me in the right direction.  I spend a RV220W which has 2 VLANS on VLAN1 with a 192.168.1.x and VLAN 104 subnet with a subnet of 192.168.104.x.  Port 4 of the goes to port the SG300 Switch 20.  Port 20 switch SG300 has VLAN 1 as non-marked and labeled as VLAN104.  It also has the port configured in the same way 15 and 16.

  In my ESXi host NIC2 is in the 16 port and NIC3 is in port 15.  I created a Standard vSwitch1 and created two groups of ports.  192.168.104.x group has a vlan id of the 104 and group vmware with no id vlan.  I guess that when I put a virtual machine in vmware port group I would get the IP 192.168.1.x what I do.

  When I put a virtual machine in port 192.168.104.x I guess I should get an IP of 192.168.104.x, but I have not, I get a return address of loop group.

  Any ideas what I am doing wrong?  I'm assuming that by creating the port group 192.168.104.x with id VLAN 104 that is the vlan native untagged for this option, which would then send the traffic through the port 15 or 16 depending on the tag VLAN104.  That would be so only send traffic out port 20 to port 4 of the RV220W which should serve as a DHCP server for the this response as 192.168.104.1.

  Just at the moment where I think I have a handle on the VLAN, I'm wrong.

  Thank you

  I would recommend this:

  Configure an access port on SG300, with no trunking

  Configure it to VLAN 104

  Place your desktop on this VLAN

  Configure your desktop and virtual computer with a static IP address

  Test if they have connectivity

  This excludes the configuration of VMware and confirm that your trunk to the SG300 is operational.

• My canon EOS 20 d is not detected by my computer lenovo, OS Windows 7, 64-bit and my computer Gateway Laptop windows vista 32 bit operating system

  My canon EOS 20 d is not detected by my computer lenovo, OS Windows 7, 64-bit and Gateway laptop with Windows Vista 32 bit operating system.  This means plug-and-play is not available or does not so I have to use for my compact flash card reader to transfer pictures.  I've already updated the firmware by downloading the upgrade of the Canon website.  I tried to turned touble this problem following what is suggested in the Canon Website, and still the problem is not corrected.  Thank you.

  Hello

  Follow the steps mentioned below and check if the problem persists.

  Method 1: Open the hardware and devices Troubleshooter

  http://Windows.Microsoft.com/en-us/Windows7/open-the-hardware-and-devices-Troubleshooter

  Method 2: You can also try to connect the camera to a different port and check if it helps.

  Method 3:  You can also try changing the normal mode to print/ptp in camera mode where you can print directly from camera by connecting printer directly using the usb cable.
   
  Hope this information helps.

• Installed Windows 7 on gateway E4500 PC and now there is no Audio as well as does not recognize do not identify/2nd monitor

  Installed Windows 7, 32-bit on the new hard drive. Gateway PC E4500. Cannot get audio and does not identify/2nd monitor. Already used Windows XP. Works well when the drive with win XP is reinstalled. Is Windows 7 compatible with this PC?

  Original title: WINDOWS 7 installation, 2 numbers

  Hello

  There is a gateway E - 4500D and E-4500 s model.

  Enter the model number on the link:

  http://us.gateway.com/GW/en/us/content/drivers-downloads

  E - 4500D has been supported by the gateway and gateway provided drivers for Windows 2000 Pro and XP 32/64, Vista 32/64.

  E-4500 s is supported under XP 32/64 or vista 32/64

  No support or drivers for Windows 7 32 or 64 bit.

  You can try the Audio drivers for Vista; no warranty if.

  See you soon.

• Transparent gateway for Sybase Oracle free and what are the versions

  Transparent bridge Oracle (for Sybase) - is this free product option or it requires a license from Oracle? If used, is there a minimum version of the Oracle required database?
  Thank you...
  
  Published by: user601798 on 10 July 2012 13:18

  Hello
  The bridge that made that send SQL to the remote database, then there may be network delays sends the data back to Oracle.
  However, the main problem with any modem router is when data must be post-processed. This means that all data from a remote select must be returned to the Oracle database to be processed when you use the syntax or functions and such like that cannot be processed at the remote site.
  The following note available in My Oracle Supprot discusses this further.

  Tuning generic connectivity and gateways (Doc ID 230543.1)

  The documentation for each gateway in detail the functions and operators are supported by each gateway.

  Kind regards
  Mike

• TC and AE cable network works well, but some settings seem odd

  I was stumped by this for some time.  Despite the fact that everything works well, a setting on my TC seems inconsistent with what would be expected.  Here is a summary of my network:

  1 modem of the IAF was WIFI and DHCP active off the COAST, and it connects to the TC with ethernet.  The IP address is 192.168.1.1.

  2 TC reportedly made all DHCP and NAT functions and peripheral PSI is simply a relay for the incoming connection to broadband.  IP address is 192.168.1.2, ethernet and it is connected using static.

  3 AE network extends the network.  IP address is 192.168.1.3, ethernet, connected using static.

  4 Apple TV 4 does its thing.  192.168.1.4, ethernet static IP address.

  5. I have DHCP reservations for Beach 192.168.1.2 - 192.168.1.10 for these devices, as well as the rest - iMac and MacBook Pro, ethernet, static.

  6 DHCP set temperature 192.168.1.11 to 192.168.1.200 for mobile devices.

  The TC acts as the hub for all the rest and that is why he would hold DHCP and NAT functions, these are disabled on device of the ISP.  However, for my life, I can't not DHCP and NAT to work as router Mode.  DHCP is the only one that works.  I certainly do not have an IP given by the ISP, and there is nothing to indicate that it performs NAT functions.  If I try to change the DHCPand NAT router Mode, I get errors that there is a conflict and that the range is incorrect.  Conflicts of DHCP-range for the base station WAN address.

  DHCP not seems to work very well, but my question is which device running NAT if the TC disobeys.

  Any suggestions are appreciated.

  DHCP not seems to work very well, but my question is which device running NAT if the TC disobeys.

  NAT is handled by the device of the ISP that you call the 'modem'... but this is very probably a device modem/router or gateway... that despite what you think, does not as a simple modem.

  If it were, it must provide a public IP address of the time Capsule and instead provides a private IP address (192.168.1.2) of the time Capsule.

  A public IP address cannot start with 192.x, 172.x or 10.x

  When you have your modem/router configured properly as a simple modem... then... you will be able to configure the time Capsule as the main router to your network using the DHCP and NAT correct setting, without seeing errors like Double NAT or incompatible IP address range.

  Some modems/routers and gateways can be configured to operate as a simple modem, and some may not. If your modem/router provided by your ISP, you may need to check with them to see if the device can be configured to operate as a mode modem simple bridge, providing a public IP address unique to the time Capsule.

  Moreover, when the Capsule is configured as a router, the default IP address range that he uses is 10.0.1.x.  The Capsule will be 10.0.1.1 on the LAN and devices will be at 10.0.1.x.

• HPDM: HPDM replace self signed SSL certificates for server HDPM and master repository

  I am trying to replace the automatically generated self-signed certificates (issued to DM) issued by DM server HDPM and master repository.  I'm NOT arbitration FTPS, HTTPS embedded HPDM or CERT Thin Client Agent server.

  I already have CERT for the installation of our own internal domain CA for FTPS in IIS and the built-in Apache HTTPS server.  These work properly and pass tests of repository for both protocols.  I also have questions for Thin Clients of our internal CA very well.

  I am interested in the HPDM real server cert and cert master repository. These are generated automatically when the two services start.  They use a very weak MD5 hash and key RSA 1024.  I can't find any documentation around that, with the exception of troubleshooting, in which you can remove these certificates restart services and they will be regenerated.

  Here are the paths certs\key
  HPDM % install Path%\MasterRepositoryController\Controller.crt (Cert repository)

  HPDM % install Path%\MasterRepositoryController\Controller.key (repository key)

  HPDM % install Path%\MasterRepositoryController\Client.crt (HPDM Server Cert)

  HPDM % install Path%\Server\Bin\hpdmskey.keystore (Both HPDM server and repository Certs and keys) (not sure what format it is in.  It is not PEM and P12 ok I can say)

  There are also some HPDM % install Path%\Server\bin\hpdmcert.key.  Don't know what it is.  It's the key to the server HPDM but deleting it does nothing and it is never re auto generated in one of my tests.

  I am able to replace the Controller.crt and keys with my own files CA internal those emitted very well.  The service started and no errors occur.  However if I replace the Client.cert (HPDM Server Cert) with my own service will start but there are Socket SSL errors in repository logs and the HPDM server could not connect to the master repository. I have no idea where the key file is supposed to be for HPDM Server Cert.

  Can anyone help with this?  I can't find the configuration files for the service to generate their own certificates.  If I did I would try at least to change the config to do not use MD5.

  Hello

  These certiricates between HPDM server and MRC are not designed for customizable. Please submite one scenario if you have concerns of security on it.

  Just for info:

  hpdmcert. Key is for communication between the server HPDM and gateway HPDM

  hpdmskey.keystore is for communication between the server HPDM and MRC

  server_keystore is for the commhucation between HPDM server and the Console HPDM