NB200-h-13 - no response from the DNS server and gateway
Hello
I have netbook NB200-h-13 with XP SP3. Its impossible to connect to wireless internet and the error messages are
HE DIDN'T THERE WAS NO RESPONSE FROM THE DNS SERVER
HE DIDN'T THERE WAS NO RESPONSE FROM THE DEFAULT GATEWAY
The connection with the ethernet cable is ok with the adpter reltek that also adpter atheros ar9285 WiFi is activation, working properly and the modem router signal is strong.
Hi abk55,
What program you receive this error message?
Have you tried another browser, for example Firefox or Opera?
I guess it has something to do with your wireless network card or WLAN parameters if the LAN cable is working properly. So you should try to update the WLAN driver on the Toshiba site.
Also, try to disable the filtering of MAC addresses and use another encryption.
Tags: Toshiba
Similar Questions
-
Incorrect response from the SOCKS server deploy when debug_token.bar
I created the debug_token.bar
and try to deploy it to the device. (Device Manager blackberry can recognize the device)
I called
/ Motion Developer/SDK/Research\ In\ / BlackBerry\ 10 WebWorks\ SDK\ 1.0.4.5/dependencies/tools/bin/blackberry-deploy - installDebugToken /Users/myname/debug_token.bar 169.254.0.1 - password mydevicepassword
After 2 or 3 minutes, it reported:
Error: Unable to connect: incorrect response to the SOCKS server. Check the settings of IP address for the target. Try to ping the target.
I ping peripheral ip to 169.254.0.1
He responsed:
Ping 169.254.0.1
PING 169.254.0.1 (169.254.0.1): 56 data bytes
64 bytes from 169.254.0.1: icmp_seq = 0 ttl = 255 time = 2.406 ms
64 bytes from 169.254.0.1: icmp_seq = 1 ttl = 255 time = 0.881 ms
64 bytes from 169.254.0.1: icmp_seq = 2 ttl = 255 time = 0.803 ms
64 bytes from 169.254.0.1: icmp_seq = 3 ttl = 255 time = 0,869 ms
64 bytes from 169.254.0.1: icmp_seq = 4 ttl = 255 time = ms 1,080
64 bytes from 169.254.0.1: icmp_seq = 5 ttl = 255 time = 0,848 ms
64 bytes from 169.254.0.1: icmp_seq = 6 ttl = 255 time = 0,823 ms
64 bytes from 169.254.0.1: icmp_seq = 7 ttl = 255 time = 1,175 ms
64 bytes from 169.254.0.1: icmp_seq = 8 ttl = 255 time = 0,893 ms
64 bytes from 169.254.0.1: icmp_seq = 9 ttl = 255 time = 1,130 ms
64 bytes from 169.254.0.1: icmp_seq = 10 ttl = 255 time = 0,860 ms
64 bytes from 169.254.0.1: icmp_seq = 11 ttl = 255 time = 0,819 mseven though I checked ndk ide, the device has been connected
He likes without any problem, but cannot deploy token
Welcome to any comment
Have you tried to deploy from the NDK since it is able to connect? It could be using the connection, prevents your order manually run to connect.
-
Is it possible to copy a file from a remote ftp server to a local folder, while retaining the original file name? Please note: the file name on the remote server is not always the same.
This article from Adobe might be useful. (I was tempted to use LMGTFY; but I do not have).
V/r,
^_^
-
Response from the RADIUS server
Hello
I added a controller to the ACS, as an AAA client then set the ACS in the WLC, but I can't be able to authenticate the users of ACS only local users on the WLC how can I get on it? help please.
The 'bad request to NAS' usually indicates incorrect shared secret parameters. Please
check or reconfigure the secret shared on the controller and the ACS for this SIN, do not copy and paste.
-
I want to spend some of my emails from the IMAP server and save them on my hard drive
I'm an iMac user who just flipped to Thunderbird. I can not all topics that deal with this issue. I see the 'local folders' at the bottom of my email accounts. This is where I can implement the records to move email messages on my hard drive.
I have just emails I want to save locally and not clutter my IMAP server.
You have got it. Local folders is the planned location for the storage that is. local and independent of all servers.
-
Reading file from the ftp server and importing data into the table
Hi experts,
Well, basically, I text with different layout files have been uploaded to an ftp server. Now, I must write a procedure to recover these files, read and insert data into a table... what to do?
your help would be greatly helpful.
Thank youuser9004152 wrote:
http://it.Toolbox.com/wiki/index.php/Load_data_from_a_flat_file_into_an_Oracle_tableSee the link, hope it will work.
It is an old method, using the utl_file_dir parameter that is now obsolete and which is frankly a waste of space when external tables can do exactly the same thing much more easily.
-
The response from the query web service
Hello
I would like to apply for assistance in creating an appropriate query to process the response from the web service.This is the outdated response from the web service and my unsuccessful attempt to treat.
PROCEDURE PRIMER_4B AS
XML_WS XMLTYPE.
CLOB DONNEES_XML
': = ' < s: Envelope xmlns:S = 'http://schemas.xmlsoap.org/soap/envelope/' > '.
< Body >
"< ns2:getDataResponse xmlns:ns2 ="http://service.anyxxx.com/">."
< return >
< id > 124 / < ID >
< name > Ana < / name >
< / return >
< / ns2:getDataResponse >
< / Body >
< / s: Envelope > ';CSR OF CURSOR IS
SELECT C.
FROM XMLTable)
XMLNamespaces)
' http://schemas.xmlsoap.org/SOAP/envelope/ ' LIKE 'SOAP'
, by default ' http://service.anyxxx.com/ '
)
, ': soap envelope / soap: Body/getDataResponse/back '
PASSAGE XML_WS
path id varchar2 columns (20) "id."
path of the varchar2 (30) name 'name '.
) C ;
rec_CSR CSR % ROWTYPE;BEGIN
XML_WS: = xmltype (donnees_xml);
Open the CSR;
LOOP
EXTRACT THE CSR IN REC_CSR;
DBMS_OUTPUT. Put_line (' Output: ' |) REC_CSR.ID |' '|| REC_CSR. (Name)
When the exit CSR % notfound;
end loop;
DBMS_OUTPUT. Put_line('Total:'||) CSR % ROWCOUNT);
close the CSR;
END PRIMER_4B;The result is:
Output:
Total 0
Thank you
KostadinHello
This part does not:
default 'http://service.anyxxx.com/'.
If you declare this uri as the default namespace uri, then 'return', 'id', 'name' nodes are supposed to be in this namespace, which is not correct, because they are in any workspace names.
Solution: give a specific prefix of the namespace above and reference it accordingly in the XQuery expression:
C. SELECT
FROM XMLTable)
XMLNamespaces)
"http://schemas.xmlsoap.org/soap/envelope/" AS "SOAP."
, 'http://service.anyxxx.com/' as 'ns2.
)
, ': soap envelope / soap: Body / ns2:getDataResponse / back '
PASSAGE XML_WS
Path id varchar2 COLUMNS (20) "id".
, path of the varchar2 (30) name 'name '.
) c ;
-
The DNS server does not - wired - wireless is OK
Hi all
This problem has left speechless several other computer scientists, I thought I'd try this forum before making a complete reinstallation. Here's a challenge to test your intelligence.
Here's the situation:
Dell laptop (11 months - still under warranty) with Wi - Fi and ability. Originally supplied with Vista, but I installed Win7 in November. I tried to do the clean installation method, but do not know if I managed to 'clean' approach because I thought that my data may be wiped. He was not, he is still on the machine. But W7 seems to work very well, I added Slowey some software. I think I was able to communicate with a wired connection before on the machine, but now I can't be sure. The machine communicates wireless without problem. IE8 opens fine. If I connect the wire and cut the antenna or boot to the wire with antenna, the machine starts and works well, but does not connect using IE8. I get a message "the DNS server is not responding.
The machine can ping and ping just fine on the wire. A chat session with Dell yesterday (Citrix I think) succeeded in transferring to wire wireless when I turned off the antenna. In addition, the MS patch notification came through this morning, but I can't download the patches on the wire.
Here is what has been tried so far:
- Changed cables and ports in the router to check the status of these question: these are OK.
- PC directly connected to the router: same problem.
- Verified services running (Control Panel-Admin tools-Online Services online):
System event COM + (for WZC issues)
Computer browser
DHCP client
DNS client
Network connections
Network location awareness
Remote procedure call (RPC)
Server
TCP/IP Netbios support
Automatic configuration wireless (only XP wireless configurations)
Autoconfiguration WLAN (wireless Vista only configurations) service
Workstation - Verified IPv4 is defined in order to obtain the IP address automatically.
- Reset IE8. No change.
- Turned off the Windows Firewall.
- Tried to access internet using Chrome. No go.
- Wired NETWORK card uninstalled and reinstalled driver. Downloaded last at Dell, they pushed also later. No luck.
- Tried the Google Open DNS. No difference.
- ipconfig/flushdns
- TCP/IP stack repair (run as Administrator: start, all Programs\Accessories and right click on command prompt, select "run as administrator" to open a command prompt.)
-Entries reset WINSOCK to default installation: netsh winsock reset catalog
-Reset the battery TCP/IP IPv4 default installation. netsh int ipv4 reset reset.log
-Reset the battery TCP/IP IPv6 default installation. netsh int ipv6 reset reset.log - While in Safe Mode, disconnected wire: uninstalled the driver for the CARD. Started full W7: installed the latest driver.
- In Safe Mode, the stack TCP/IP repair as described above.
All to nothing does not. IE does not connect to the internet. Chrome is not connecting to the internet.
You people have any ideas what the devil is wrong with this machine? Can you offer any suggestions to try to get access wired for the functioning of the internet?
Thanks in advance!
Hello Stringout,
I said to reset the router because the router is the DNS server and assigns the IP address to all devices on the network. Now, since you get the error "DNS server is not responding. It may possible that this router is not able to assign the correct ip address to all computers.
You can also try to update the router with the latest firmware. Still, Microsoft!
-
Change the DNS server, but consider e-mail to Office 365
I now have a customer who wants his site softdanmark.dk moved and accommodated with catalyst for business as the new design I've done for the company by muse and previewed as: softdanmark.businesscatalyst.com.
I've already added the domain name to Business Catalyst and gave him the dns data, but he still wants the email (MX) belong to the TDC, where he has his Office 365.
Is it possible to only move the DNS server and keep the MX record at the old company?
Hope you can answer my question.
Hey there,
You do not change the NS records, all you need to do is point the web traffic, so yes, have your screenshot you just need to change the record and when you set up the site in British Colombia you say outside.
Registration information are:
-
PL/dynamic sql to retrieve the data from the production server
Hello
I need to create a dynamic pl/sql program to retrieve all packages from the production server and store it on my local machine in another file.
Thanks in advance.Hello
user9963922 wrote:
Hi Peter,.Thanks for the reply.
I need make my block dynamic while in a single query, for different packages I can save it in another file with the same name as the package on my local machine.What is the problem with the suggestion of Peter? This is not 'dynamic' on this subject?
To save the code in the files, use utl_file. Inside the loop, open, write, and close a file. If you need help, your zip code and a description of the specific problem.It is also possible to use only user_source table to accomplish the task.
Yes, but it doesn't work for you own schema.
If you do not use user_source, then you will not need any condition asand owner in ('
') -
DNS server and mail cross-site fell down.
After restarting the Windows Server2008, the DNS server and mail cross-site not may start automatically. So I want to start these two are manual. There is no information in the log file or no code error on this issue. How can I solve this problem? Anyone knowing the solution please answer me. Waiting for your valuable suggestions.
http://www.Microsoft.com/windowsserver2008/en/us/forums-blogs.aspx
Repost in the above Forums Windows Server 2008.
These are the Vista Forums.
See you soon.
Mick Murphy - Microsoft partner
-
Satellite Pro P100: Wlan with no response from the server proxy C-27
I have a laptop model Satellete Pro P100 and tries to connect to a wireless router.
I was able to connect to it over the past four months.Last week, I connected to a wired network and now he refuses to re - connect to my home wireless network. He acknowledges that I am connected but connectivity doctor says "there is no response from the server proxy (c-27).
A friend in the House is able to connect to the internet with their computer without problem.
I have tried everything I know, but need help please. Thank youHello
Have you checked in the properties of Wlan settings and the TCP/IP properties?
Please check if the options: IP automatically get an address and get server address DNS are automatically set correctly. -
error message when try to sync the iPhone, "invalid response from the device?
What can I do when I receive this error message when you try to sync to my iPhone 5 s - "invalid response from the device?
-What are your 5 updating to 10.0.2 iOS iPhone? If this is the case, you must have the latest version of iTunes on your computer, which is required for Mac OS X 10.9.5 12.5.1, or above. To meet these specifications will be receiving this error.
-
Cannot connect iPhone 7 more to iTunes because an invalid response from the device
I tried to sync my phone to iTunes and I get an error message stating "invalid response from the device. I tried to remove the password, and it still doesn't work. I also tried using a new USB cord. I'm doing something wrong? I can't sync my music or ringtones. Will there be an update to iOS 10 soon to solve this problem? I am extremely disappointed that I can not connect my new phone!
You use iTunes version 12.5?
-
No Satellite Pro 6100 no response from the screen
Can anyone help?
My 6100 Pro Satellite lit last night then automatically went into hibernation, despite being connected. Now when I turn it on there is no response from the screen, but if I plug a monitor to the laptop, the screen works (as long as I start in safe mode)
Can anyone help?
Hi Simon
Disconnect all cables from the laptop and remove the battery.
Wait a moment more (20 min) and reconnect the battery and the AC adapter.
Then check if the laptop turns on and if the display works fineGood luck
Maybe you are looking for
-
New Toshiba Satellite S50 pixelated icons - C series and photos on Yahoo
Hi, I like to browse using Mozzilla which I just downloaded on my laptop brand new. I set Yahoo as my face page, but all of them are pixelated as it is the Home icon and all the small icons in the upper right. Is not this way on internet explorer, wh
-
When I select the tv out, screen is black and white, I also chose pal!
-
Whenever I open Firefox on my Macbook, I get video game music blasting. Looks like PacMan. This has happened Each time Firefox opened Is today
-
Has anyone tried using the Dymo label with software V8 printer? If I create a label template using this software, I'm not able to see the content on my label. I used the Dymo Labview add-on and it works if I create a label by using earlier versions o
-
Why my E709a all-in-one printer go offline? How can I put it back online?
Why I can't keep my E709a all-in-one online? How can I put it back online?