I can't take a picture to copy into the Clipboard on iPhone iOS 9.2!

Similar Questions

• I have a canon eos rebel sl1/100 d. I can't take a picture.

  I can't take a picture. The battery works, the memory card has been reformatted. I had the unit about 6 months. I took a lot of pictures on vacation this summer. I uploaded these photos. I started taking pictures, and I can't get a picture.

  If the unit is in 'One Shot' factory default mode, so should not be a picture unless it can confirm that it was able to lock the focus on a subject.  No accent... no picture.

  If, however, you reverse this little switch on the side of your lens that says "AF/MF" on the "MF" position (it is 'Manual' and AF is "Update automatically") THEN you get an exception... "MF" position, the device is ready to take a picture no matter if she thinks that the image is sharp or not... He doesn't care.  Touch that little switch to "MF" you said on camera that YOU will take care of the update and it is not not to consider the development at all.

  If the camera will take a picture (even if it is blurry) when the lens is in a position to "MF", this means the reason why he was not taking a picture before is because of his inability to focus.

  There may be a few reasons why a camera could not focus.

  (1) not enough light: to test this situation... just go to a place where there are a lot of light.  ... Outside in the middle of the day.

  (2) a problem with one of the systems of development.  It turns out that your camera has in fact two systems different focus (completely independent).  One is used when you are looking through the viewfinder to compose the picture.  The other is used if you use the live view screen to compose view.  The reason why there are two different systems is because your camera has a mirror inside.  When you look through the viewfinder, you are actually looking through the lens.  To do this, they need to put a mirror between the lens and the sensor, so you can browse through the same lens that camera is to use.  But which reflect the light to reach the sensor blocks.  So they actually have a system of development that does not use the sensor and can focus when the mirror is in the way that (the mirror of the part of the light bounces actually in focus sensors).  When the mirror went away (for the live-view shooting) it obviously can flip any light in this special focus sensor.  To remedy this, it uses image sensor of the camera work on the update.

  The two systems are independent, and the only thing in common is that they both send instructions to the lens to move the focus in or out.    If a system of development does not work... try another (update looking in the viewfinder... and test development using the "live view" mode (only not looking in the viewfinder.))

  (3) but that leads us to the third possible problem: the lens.  The engines of development (for any Canon camera) are in the objective... not in the camera.  The camera simply gives instructions to the lens it say how adjust the setting to the point and to what extent.  Is there a problem with the lens, then it can not focus... even if there is absolutely nothing wrong with the camera itself.

  If you have a different purpose, you can swap lenses and see if the camera still has a focus problem.  If it has only a focus with a particular lens problem... it's the objective that needs service and not the camera.

• How can I get my pictures to display in the order they were taken?

  How can I get my pictures to display in the order they were taken?

  Hey Mole,

  Greetings.

  • Open LR, go in the downstairs library module, click the capture time in the sort order.

  

  Concerning

  Rohit

• Copy to the Clipboard, method (Table) copy an extra empty column more than expected

  Hello

  I use the copy to the Clipboard method for a Table, for example copy 4 rows with 3 columns. When I paste in Excel I get 4 rows with 3 columns and an additional column, which is empty, then the actual size is 4 x 4.

  Is it a mistake to Labview or can someone there explain to me why this is happening? Or better yet, how can I fix it?

  I've isolated the problem to an additional vi so that you can reproduce the error. Just let the vi run once and then paste the Clipboard to Microsoft Excel.

  My Labview Version is 11.0 32-bit, Microsoft Office 2010, WinXP SP3

  Concerning

  Marcel

  Extracted apparently hate property and invoke nodes.

  See attached vi for the workaround proposed by using the Clipboard.Write method.

• Error: "files which are required for Windows to run properly must be copied into the DLL cache.

  I need some serious help please someone... I get a message that Windows File Protection is! and he says that "files which are required for Windows to run properly must be copied into the DLL cache" that I know, but I do not know why this has happened... I think it happened because of an update which took place about 2 days ago cause that is when it started, but I've tried all t0 get rid of it. I tried to disable using "regedit" in the run screen and it did not help... I need help with fixing this. I don't have my copy of Windows XP Professional Moose because this Pc is old, and I just kept to upgrade. Can someone guide me please in the right direction and the easiest that I'd appreciate it, thanks Chris!

  Thanks to all who tried to help, it means a lot!  I have no idea what happens but I tried to run a complete scan with antivirus program McAfee I was BTW it was free because of the internet service gave to me to be a customer with them, (I guess they have an ongoing case) not much of a cause I had nothing else problems with McAfee all for about 5 years and they are so much better programs out there (to new my opinion) but on with my story so whenever I tried to run a full scan or fast he rode every time error cannot start scan try again and so on, so I called them and they could not understand what the problem was and finally reinstalled but it doesn't work and of course they wanted me to buy a version... So I said forget it and went with one of the best Antivirus out there (my opinion only) programs free and it scanned and found some articles ad and he never came back! So I'm lucky so far and happy! Once again thanks to Jose @ and @ John for help and getting back to me, that shows the high level of awareness and dedication... So thank you to you two! I have no idea of what the problem was I think that he had with the Ad-ware and anti virus program does not properly and somehow obtained a "bug" If you want to. Have an awesome day and thank you and if I can ever be useful I'll do my best! I was wondering something quick you guys like Avast Internet security because I've had some people said he is well worth and had some interesting features, I personally put AVG but I was wondering about obtaining notice! Thanks for the tips when you get the time!

• Can photos and music will be loaded into the memory of the dashboard?

  Can photos and music will be loaded into the memory of the dashboard?

  Hello Tom,

  The internal memory of the Dash device is not accessible to the user. Therefore, pictures and music files cannot be uploaded to the internal memory of the dashboard.

  However, the USB port on the Dash unit allows you to view photos or listen to music stored on a USB key.

  If my post answered your question, please mark it as an "accepted Solution".

• What key combination can be used to capture a screen to the Clipboard? __

  What key combination can be used to capture a screen to the Clipboard?

  http://en.Wikipedia.org/wiki/screenshot

  In Microsoft Windows, pressing the button print screen capture a screenshot of the whole office and put it on the Clipboard. Pressing the combination Alt - Print Screen captures only the current active window. In most versions of Windows, captured screenshots do not include the mouse pointer.

  Video content in the programs using a hardware overlay video converter is not captured by the method described above. Windows Media Player on Windows XP in its default configuration on supported hardware is affected by this. However, some third-party applications can capture overlay images.

  By default, Windows does not record the screenshot to an image file; the user is required to paste the image into a separate program (such as Microsoft Paint, which is integrated) imaging for the economy. Some programs, however, especially online multiplayer, will automatically save screenshots in a specified folder. From Windows XP (or any version based on Windows NT), it is no longer possible to take screenshots of windows DOS full screen without other software.

  Windows Vista and Windows 7 include a utility called Snipping Tool, first introduced in Windows XP Édition Tablet PC. This is a screen capture tool, which allows you to take screenshots (called snips) of windows, rectangular areas, or a free-form area. Shears tinsmith can then be annotated, saved as an image file or an HTML page or by e-mail. Unfortunately, it does not work with uncompressed, XP versions but represents an XP compatible equivalent.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://en.Wikipedia.org/wiki/Print_screen

  In Microsoft Windows, pressing print screen will capture the entire screen, while pressing the alt key pressed in combination with the screen print will capture the selected window. The captured image can then be pasted into an editing as a word-processing, electronic mail, or graphics softwareprogram. On the keyboards that have a caps lock key, you may have to press lock first. Pressing print screen, with the alt key and the SHIFT key pressed, turns on a mode of high contrast for people with visual impairments.

  See you soon.

  Mick Murphy - Microsoft partner

• help sites Web copy to the Clipboard, and then paste it on Facebook

  Hello...

  How can I copy and paste all the web pages I want to paste it into Facebook. In my Touchpad.

  When I click on the address of the Web site, at the top of the page, it, correctly, highlights the entire address, however, in the drop down menu, on the left, there is no option exemplary editing past etc.

  In addition, the only other way I found, is to try to send the link, then try to copy the link in the email send, however, that e-mail is the name of the web page text, providing a link to the page. So I can not stick to Facebook from the email.

  Am I mistaken.

  can I ask function to copy the web address to the Clipboard.

  Also is there an easy way to copy the web address on the Clipboard so you can paste facebook.

  Thank you. :-)

  Here's how:

  Press and hold on the link.  Depending on how long you hold that it can produce two results - for me, this usually points to the whole link then keyboard appears and the cursor go to the link.  Not a problem, now tap and hold your finger there until the bubble 'Select Select all stick them' opens.  Tap "select all" and the link has been copied to the Clipboard.  To where you want that it stuck and just hold your finger on the screen until the bubble even opens.  Choose 'Paste' and the link.

  From time to time, it works as it should - press and hold the link, it becomes yellow, tap again and the 'Copy' option bubble will appear.  I think that it depends on to know if the keyboard is displayed when you press the link.  Keyboard upwards and you touch & hold = "cut copy paste" dialog, keyboard facing downwards = the dialog box "select Select all paste them.

  HTH,

  WyreNut

• Message from Smartphones get BBM blackBerry copied to the Clipboard.

  Hey when I copied a BBM message it reads copied in the Clipboard...

  I can't find Clipboard anywhere on my flashlight to look at the message.

  It is not a 'Clipboard' application to display the Clipboard UNLESS you have installed a third-party application to do.

  When you copy something in your memory on the BlackBerry, it is replaced when you copy something else then. There are third-party applications that enhance this and allow you to display multiple selections to the Clipboard.

  Meanwhile, if the copied text has not been replaced, just open any new white enamel and choose Menu > paste... and read.

• the font files could not be copied into the directory of local site. Please check permissions

  Hello. I'm new here. Can someone answer me why dreamweaver cannot accept files of fonts when I try to change the style of police with the program? Im making any good by Lynda - Dreamweaver CS6 Essential Training instructions of lessons, but I have a problem when trying to add new files of fonts css rule - could not be copied into the directory of local site. Please check the permissions...   Thank you.

  Open the fonts using Windows Explorer file and try to copy from its current folder in the folder root of the site on your hard drive and see if you get a Windows error.

  Do not use DW to import the file to the site.

  I guess that the file you are trying to copy is protected.

• 15 version no longer allows to copy to the Clipboard

  We have put signed.applets.codebase_principal_support in FireFox to allow the copy to the Clipboard of Windows XP and Windows 7. It worked fine until 15 version and is no longer works. If we are unable to use this feature, we will have all our users convert to IE or another browser that allows to make the copy.

  There is sample code in the list of system details.

  • http://www.febooti.com/support/website-help/website-JavaScript-copy-Clipboard.html

  It is usually best to sign your script in such cases.

  • http://KB.mozillazine.org/Granting_JavaScript_access_to_the_clipboard
  • http://www.Mozilla.org/projects/security/components/signed-scripts.html

• In one of the inDesign tutorials instructor pulls up what looks like an application bar that contains among other things a text editor to cut and paste the copy into the inDesign project.  That is a feature of inDesign, and how is it accessible?

  In one of the inDesign tutorials instructor pulls up what looks like an application bar that contains among other things a text editor to cut and paste the copy into the inDesign project.  That is a feature of inDesign, and how is it accessible?

  The instructor used the App Switcher on Mac to switch to a text editor and copy this text editor text. InDesign is not the active application.

• Can I take a picture that is not in my photos?

  I use a lot my iPhone to work.  There are as many times I want to take a picture for the work I want not mixed in my normal photos.  Is it possible to do

  You can move photos of work to the album "hidden pictures".  Then they will not show in the Moments and Collections. http://help.Apple.com/iPhone/9/#/iphf14943e

  Hide the photos or videos you want to keep but not show. When displaying thumbnails, press Select, then select the photos or videos you want to hide. Press the button on the share, and then click Hide. The photos or videos are moved to the Hidden album.

  You can create a new album 'Work' for your photo work. Hidden photos will show in albums, but not in the moments and collections.

• How can we change all the images in the import of ref file to copy into the doc?

  Y at - it an easy way to change all the images in a file 'import by reference' to 'copy in the document '?

  The way I currently have to do is delete and re-import and resizing an image at a time and even in a

  single document with 30 images, this can take forever! Surely it more soon than that?

  My company has always used the "Import by reference" option when you add images to our frame documents.

  But things have moved on and we are now a global business and send a large number of these files to our sister sites.

  E mailing 1 file is much more logical to emailing file 1 framework and 40 image files, especially when files

  are in a different folder structure.

  ACE,

  You have a lot of good advice here on best practices, but I don't think that someone at - it answered your question. The answer is no, there is no way easy, unless you have access to the FrameScript or the FDK.

  Russ

• Can I put a picture/image/vector on the way to text?

  I need a small picture to move with the text as it is written, is that possible?

  Wiggy,

  If I (put) understand, each font will retain its properties, then Yes.

  To apply a gradient to an existing instance of direct/police Type, you can:

  (1) choose the Type and the value Fill None (Toolbox);

  (2) in the appearance palette dialog box, click Add a new fill and apply the gradient to the fill.

  If you only want to put a gradient on a part of the text, you can cut the text in separate proceedings, which can be attached and grouped and then apply) 1 and 2) to the desired instances.