I get the message "cannot verify your member ship, 5 days left"

Similar Questions

• During the installation of Windows 7 or 8.1 using a USB stick - get the message "cannot be installed, it is a GPT.

  Hello

  During the installation of Windows 7 or 8.1 using a USB stick - get the message "cannot be installed, it is a GPT partition.

  I have 64 bit install discs for Win 7 and Win 8.1. These two install on my desktop in duel boot. I made a Flash DRIVE of each disk so I can install it more quickly.

  Problem: I get the cannot install because it is a GPT partition.

  Y at - there no way to make these 2 USB sticks work?

  Thank you, Brad

  Make sure you create your media recovery HP or USB Flash Recovery discs before you edit or change anything.

  Your computer does not have Microsoft's Downgrade rights and you must buy a copy of Windows 7 with a valid Microsoft COA and product key.

  The screenshots below is from a laptop HP 15 t-j100... options and the configuration on your computer screens may differ.

  You will need to DISABLE "Secure Boot" and ENABLE "Legacy Support" in the "Configuration of the BIOS start-up secure" on the settings page similar to what is shown below, until you try to install Windows 7.

  

  After you save the changes, the computer will ask you to confirm the changes... Accept the changes by typing the four digit code and press the ENTER"" key.

  

  If you install Windows 7 from a USB and see a message of "load a driver - a required CD/DVD drive device is missing", it's because as 'System Configuration' > 'Config USB3.0 in pre-start' is set to 'Enabled '. This should be set to 'Auto '.

  

  In addition, as the factory hard drive is partitioned as TPG, you must start using the internal CD/DVD UEFI or UEFI-Key/key USB to install Windows on a GPT-partitioned disk. Turn on or restart the computer and press "F9" or "ESC", then "F9" when prompted. Select the source of boot UEFI you use and you press "ENTER".

  

  I suggest using Windows 7 SP1 for the best installation experience. If the DVD does not start as UEFI, you may need to use a USB Flash drive (can ask "Quick start" DISABLING in BIOS) as the installation media. Please note that some computers may not recognize a valid active UEFI USB Flash drive if it is formatted in NTFS and may require only a FAT32 formatted USB Flash drive. You should be able to make a FAT32 formatted Windows 7 installation USB Flash drive using Rufus, UNetbootin, Universal USB Installeror WiNToBootic. I like Rufus, because it contains options for 'Plan of GPT partition for UEFI computer' and 'FAT32'.

  If you have any other questions, feel free to ask.

  Please click the 'Thumbs Up' white LAURELS to show your appreciation

• Installation of Windows 7 or 8.1 using a USB stick - get the message "cannot be installed, it is a GPT partition.

  Hello

  During the installation of Windows 7 or 8.1 using a USB stick - get the message "cannot be installed, it is a GPT partition.

  I have 64 bit install discs for Win 7 and Win 8.1. These two install on my desktop in duel boot. I made a Flash DRIVE of each disk so I can install it more quickly.

  Problem: I get the cannot install because it is a GPT partition.

  Y at - there no way to make these 2 USB sticks work?

  Thank you, Brad

  Rufus can create a bootable copy instead:

  

  Rufus - credit: Pete bastard/Akeo

  After installing Rufus:

  • Launch it
  • Select the ISO Image
  • Point to the file ISO for Windows 10
  • Check create a disk bootable using
  • Select GPT partitioning to EUFI firmware as the Partition scheme
  • Choose FAT32 NOT NTFS as file system
  • Make sure that your USB in the device list
  • Click Start
  • Close when you are finished

• C7280 when I try to install from cd, I get the message cannot find 7cS5B3C

  When the cd-rom for c7280 hpdriver instaaling I get the message cannot find

  c;\users\huubs\AppData\local\temp\7cS5B3C\setup\...\setup\block [next illegible]

  And it stops

  Huub

  Hello huubs

  Try the following to "scrub" your machine HP printing software. This should clean your computer so that you can re - install the printer as if it was never installed previously. Sometimes this solves problems with the driver.

  Of the Original installation CD:

  1. Insert the CD in the drive and then cancel Setup

  2. open my computer and click right then on the CD from the drive and select open

  3 open the Util folder

  4 open the CCC folder

  5. If you have an HP computer, run the L3uninstall.bat. If you have a computer not HP, run the L4uninstall.bat

  6. once the uninstall is complete, restart the computer

  7 run the Accessories\ System Tools Disk Cleanup

  8. download and install the latest version of Adobe flash player

  http://get.Adobe.com/flashplayer/

  9 download drivers and full software features

  Photosmart C7280 Full Feature software (Windows 7)

  10. run the download to reinstall the printer

  If the software has been downloaded and extracted to your system:

  1. type % temp % in the field of race

  2. Locate and open the folder starting with 7z (example: 7zS2356)

  3 open the Util folder

  4 open the CCC folder

  5. If you have an HP computer, run the L3uninstall.bat. If you have a computer not HP, run the L4uninstall.bat

  6. once the uninstall is complete, restart the computer

  7 run the Accessories\ System Tools Disk Cleanup

  8. download and install the latest version of Adobe flash player

  http://get.Adobe.com/flashplayer/

  9 download drivers and full software features

  Photosmart C7280 Full Feature software (Windows 7)

  10. run the download to reinstall the printer

• When I send a document to someone I get the message "Cannot send a document only to you to sign." I'm not send it to me.

  When I send a document to someone I get the message "Cannot send a document only to you to sign." I'm not send it to me.

  Hi Jerryg,

  On the Send tab, you can click Show CC and see if your e-mail address is displayed or not. If so, then delete it and then send the document. Also, I would like to know which browser you are currently using.

  Kind regards

  -Usman

• Why do I get the message "cannot write in print file specified"?

  When I print from Framemaker 8 using the Adobe PDF printer driver, I get the message "Cannot write in print file specified."  And I am not able to generate ps file.  Why is this?  What could be the problem?

  I am able to print to another printer - for color printer driver - of my office with no problems.  So I guess that I don't need the Adobe PDF printer driver, but it's an others on my team use documentation - I was wondering why it is not working for me now (even if it is used for).

  Thank you

  Erin

  FM is not a true PDF Export. There is not a "SaveAsPDF", that comes silently prints (background task) a temp ps of the file using the AdobePDF printer instance, called Distiller with a specified joboptions file and deletes so the temp folder afterwards.

  AdobePDF print through the PDF port, which is actually the same as the SaveAsPDF FM approach.

  @Wish, have you checked that your AdobePDF printer instance pointing to the 'Adobe PDF' port (printer properties > Ports)? Alternatively, you can try setting the AdobePDF in the FILE: port.

  Also check that you have permissions to write system level to where you try to put the temp FM ps file.

• After the installation, I get the message "cannot use this product under a guest account. That is what it is?

  I installed Acrobat Pro XI (academic edition).  But I get the message "cannot use this product under a guest account.  What should I do?

  Run as admin / talk to your IT Department.

  Mylenium

• Try to restore my iPhone and I get the message "Cannot restore iPhone because an unknown error (50)." I got this message several times, how to fix?

  Try to restore my iPhone and I get the message "Cannot restore iPhone because an unknown error (50)." I can't chat because the phone is locked and I can not access my serial number. I got this message several times, how to fix?

  Have you already checked this discussion about this?

  The iPhone cannot be synced. An unknown error occurred (-50)

• Just installed a vigin superhub my portable computer that has a network adapter and connected to the hub, but I get the message cannot connect without certificate

  wireless problem

  just installed a vigin superhub my portable computer that has a network adapter and connected to the hub, but I get the message cannot connect without a certificate, any siggestions would be welcome

  Tom

  Hello, Bill Bates,.

  I would say to contact support with their router blank:
  https://help.virginmedia.com/system/selfservice.controller?configuration=1002&PARTITION_ID=1&TIMEZONE_OFFSET=&usertype=1&VM_CUSTOMER_TYPE=&cmd=ESCALATION_REQUEST

• When I try to open a PDF email attachments I get the message: SECURITY WARNING - your current security settings do not allow this file to download.

  Network discovery sharing sharing inbound network incoming Remote Desktop RDP TS Remote Desktop Remote Assistance Network

  
  

  When I try to open a PDF email attachments I get the message: SECURITY WARNING - your current security settings do not allow this file to download.    I am running Windows 7 and the email is in Windows Live Mail.   HOW CAN I SOLVE THIS PROBLEM?

  Thanks a lot for your help. I finally found a way to open the PDF file by saving it to my documents folder then right-click to open it in Adobe Reader. This has proved to be a more useful to any similar future problem solution.

• I get the message cannot load the configuration settings whenever I try to download Adobe Reader

  I get the message cannot load the configuration settings whenever I try to download Adobe Reader

  Try to download the adobe reader Offline Installer.

• On opening gogle I get the message: "ATTENTION!" Your Flash Player can be updated. Please update to continue"- by clicking on ok I am confused to download Flash Player Pro site? What is an Adobe product? And why, even if I have the most recent flash playe

  On the opening of google, I get the message: "ATTENTION!" Your Flash Player can be updated. Please update to continue"- by clicking on ok I am confused to download Flash Player Pro site? What is an Adobe product? And why, even if I have the latest version of flash player I received several times the message?

  This isn't a message that provides Adobe, and I recommend that you do not click the link. It seems you may have malware on your computer.

  For more information, see: http://malwaretips.com/blogs/warning-your-flash-player-may-be-out-of-date-virus/ or http://wasconet.com/how-to-remove-warning-your-flash-player-may-be-out-of-date/

• I get the message "cannot find the file NOT. CHM error 2 "

  Original title: what is concentr.chm with error 2

  I get the message: can't find file. CHM error 2.  Also tried reinstalling my C4200 printer, but he always tells me that its already installed, though even I uninstalled it a dozen times.   I have a Windows 7, 64 bit.

  The extension .chm file is a Windows Help file extension.

  You are running the latest version of Citrix software with that you get the error?

  In addition, if the file is on your system, make sure it is not blocked:

  1. Click right on your. CHM file
  2. Click the general tab
  3. Go to the bottom and click on UNLOCK, APPLY and OK
  4. Now you can open the document.

• Unable to delete the file, get the message "cannot delete * access denied»

  How can I remove a file with the Message: "cannot delete * access denied»

  This happened after an attack on Trogan

  Hello

  Use the other methods in the convenience store posted above to be sure all malware
  is detected and deleted that no one program can do everything.

  If it was a program of antivirus/antispyware fake/rogue that the name could use led to
  a more specific help if necessary.

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• recover my system. used to install Windows Vista. get the message cannot open the file E:\Sources\Install.wim. Also the code error 0 x 80070002

  So all this started because I tried to clean my computer to give to a friend. I tried refomatting the hard drive, but something was wrong here. After that, when I turn on the computer I get a black screen with message Bootmgr missing. I read a little inside and saw that I could download a Windows Vista recovery disk because my computer did not come with one.
  After that I downloaded and burned the ISO image to a CD, things started looking better. I got to the screen when you select the language and keyboard. Then install windows screen. My options there were 'Install now' and 'repair your computer '. When I try to install, I put in my product key that seems fine. The next message I get is "Windows cannot open the required file E:\Sources\Install.wim. The file does not exist. Make sure all files required for installation are available, and restart the installation. "Error code: 0 x 80070002.
  When I try to repair, he said "select an operating system to repair, and then click Next."
  Operating System: Windows Vista (TM) Home Basic (recovered)
  Partition Size: 34318 MB
  Location: (D :) ACER
  If you do not see your operating system listed, click on load drivers to load the drivers for your hard drives. I try to select Windows Vista retrieved and clicked Next, but what is said "this version of system recovery options is not compatible with the version of windows that you want to repair" or get a recovery of tools such as repair system, System Restore, complete pc windows, tool windows and command promy memory diagnostic restoration. the only problem is he says operatins system: (unknown) unknown local disk...

  Any help would be appreciated. Really want to give my friend a laptop that wont even turn on. Laughing out loud

  Was it Neosmart?

  This isn't an installation disc. It's a record of startup repair!
  You use the repair disk option, not Install.

  How to get Vista recovery Media and/or to use the Vista recovery Partition on your computer.

  There is no Vista free download legal available.

  https://secure.TX.Acer.com/rcdb/main.aspx?brand=Acer

  Contact your computer manufacturer and ask them to send a recovery disk/s Vista set.

  Normally, they do this for a cost of $ small.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  In addition, ask them if you have a recovery Partition on your computer/laptop to restore it to factory settings.

  See if a manual provided with the computer or go to the manufacturer's website, email or you can call for information on how to make a recovery.

  Normally, you have to press F10 or F11; Acer is in some models Alt + F10 at startup to start the recovery process...

  Another way I've seen on some models is press F8 and go to a list of startup options, and launch a recovery of standards of plant with it, by selecting the repair option.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Ask them if you can also make recovery disk/s for the recovery Partition in case of a system Crash or hard drive failure.

  They will tell you how to do this.

  Every computer manufacturer has their own way of making recovery disk/s.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Or borrow a good Microsoft Vista DVD (not Dell, HP, etc).
  A good Vista DVD contains all versions of Vista.
  The product key determines which version of Vista is installed.

  There are 2 disks of Vista: one for 32-bit operating system, and one for 64-bit operating system.

  If install a cleaning is required with a good DVD of Vista (not HP, Dell recovery disks):

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu

  http://support.Microsoft.com/default.aspx/KB/918884

  MS advice on the conduct of clean install.

  http://www.theeldergeekvista.com/vista_clean_installation.htm

  A tutorial on the use of a clean install

  http://www.winsupersite.com/showcase/winvista_install_03.asp

  Super Guide Windows Vista Installation

  After installation > go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > get latest Vista drivers for it > download/install them.

  Save all data, because it will be lost during a clean installation.

  See you soon. Mick Murphy - Microsoft partner