I hear no sound during edirting in the first

Similar Questions

• iPhone 5 c does not always sound during calls to the.

  iPhone 5 c does not always sound during calls to the.

  Is do not disturb on?

  This is the icon of Crescent Moon at the top right of the screen

  If yes – you can control center - activate by sliding upward on the homescreen of the lower edge and tapping on the icon

  If this is not the case - check to see if these contacts are in your blocked list

• Dell xps l502x freezes making buzzz sound during playback of the audio or video file

  I have a two year old dell laptop xps l502x, who recently started producing some strange audio buzzz at regular intervals during playback of audio or video file.le sound is very similar to the sound when games used to freeze with the same anonying buzzz sound which is a very well known with the XPS L502X.i used only to have problem that the sound during games used to hang , but recently it has begun to occur during playback of audio or video files too.

  RTZ87,

  I just had a quick glance and the solution is in the thread below. Uninstall 'Dell Support help' and 'Dell Support Assist Agent'. They have been automatically installed on your laptop in the last two days and seem to be causing the problem.

  

• Sound is played at the first time when it is called by VI

  Hi, I am creating a VI that creates bursts of noise of specific terms in the sequences. My problem is that the sound generation VI only plays the sound the first time it is called. I tried to put VI in a for loop to see if I can get to play several times, but no matter what I do it plays only generated sound once.

  I found the problem. Thank you. The problem was with the timer not reset in the loop (it fixed with a shift register) on second or other calls. Thus, the loop was ignored that the timer has been greater than the value specified after the first time through the loop.

• Speech recognition is not all sounds during installation of the wizard.

  Sound recorder works fine and I can record, save and play wav files.  CLS recognition requires all upward before use and the recording meter bar moves I read the sentence of the sample.  After that, I get the error that SR couldn't hear anything.  Help please.

  Hi BTKpickle,

  Welcome to Microsoft Answers Forum.

  There are several possible causes of the problem:

  ·         The microphone isn't close to capture your voice. Make sure that the microphone is positioned close enough and you speak directly into it.

  ·         The microphone is cut in. Some microphones have an external control for muting. Make sure that the mute control is disabled.

  ·         The microphone input level is too low. Make sure that the microphone input level is set correctly.

  Entry level to adjust the microphone

  1. Open Audio devices and sound themes by clicking Start , clicking onto Control Panel, hardware and sound, and then clicking its.

  2. click on the recording tab.

  3. double-click on the microphone you are using speech recognition.

  4. click on the tab levels and then use the slider to adjust the entry level for your microphone.

  ·         The microphone connections are not properly attached. Make sure that microphone cables are intact and unbroken. The connections to the computer can be loose, so unplug the wires and reconnect them by ensuring that they fit.

  ·         A different microphone is selected to be used with speech recognition. If you have more than one microphone installed on your computer, that bad could be selected to be used with speech recognition. Make sure that you use the microphone selected for speech recognition.

  Change which microphone is used with speech recognition

  1. Open Audio devices and sound themes by clicking Start , clicking onto Control Panel, hardware and sound, and then clicking its.

  2. click on the recording tab.

  3. Select the microphone that you want to use with speech recognition, and then click set as default.

  Check the documentation that came with the microphone for additional troubleshooting information.

  See if you are able to complete the installation wizard.

  For solutions to common problems with Windows speech recognition, see

  Troubleshoot speech recognition

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-speech-recognition-problems

  I hope this helps.

  Kind regards

  Shinmila H - Microsoft Support

  Visit our Microsoft answers feedback Forum and let us know what you think

• The Windows media player 11 no sound during playback of the songs in the library

  Windows Media Player 11 is no longer being on any sound, but only when I try to play a song in the library, but it is sound when I play a CD or play a video clip with the player, so the speakers & sound card are ok. The track is played physically because the small bar at the bottom of the player moves from left to right and the timer starts counting from zero until the end of the track. I am able to hear the songs in my library if I open it with VLC Media Player. I had no problem in the past, then one day there was no sound... Any suggestions?

  Pete

  Hi Geekygreek,

  Welcome to the Microsoft Answers site!

  Try this step.
  1. click on start > Control Panel (Classic view)
  2. open the hardware and sound > sound >
  3. right click on the speakers and choose the Set as default option.
  4. check if you are able to hear the sound.

  Let us know the answer.

  Kind regards
  Bindu S - Microsoft Support
  Visit our Microsoft answers feedback Forum and let us know what you think

• sound during playback of the recorded music is bad

  the sound on my acer crystal eye webcam plays terrible back. I record music played on my guitar, but playback is really bad. (not bad but not good singing music) if I could use a microphone outside and if so, how?

  Hello

  If I understand correctly, you need information on the connection of an external microphone on your Windows 7 computer. Do not worry, I'm here to help you with this information.

  Let us try the following methods and check if it works for you.

  Method 1:

  Run the fixit in the following Microsoft FixIt.

  Diagnose and automatically fix problems of Windows audio playback:

  http://support.Microsoft.com/mats/AudioPlayback/

  Method 2:

  Try the steps in the following article from Microsoft Help to connect the Microphone on your computer.

  Connect one microphone, music player or other audio device to your computer:

  http://Windows.Microsoft.com/en-us/Windows7/connect-a-microphone-music-player-or-other-audio-device-to-your-computer

  Please answer if the steps did not help, so that we could help you better.

• I have a NVidia GTS450 with HDMI output. When I connected it I had sound & vision. After the first time that I turned off the desktop computer sound options just told me THAT HDMI is not connected?

  I am running Vista Home Premium 32 bit. It does not seem to recognize the connection although it is really connected and one / v amp is running. I get the desktop on the HD TV but no sound.

  Hello

  By default the Vista transmits no sound on HDMI output.  To change this to change the settings in the control panel.

  Note: This will turn off sound from speakers or normal audio output on the laptop.  To get that back, you will need to reverse this process.

  a. click on the button 'start '.

  b. click on 'control panel '.
  c. with the control to the "Control Panel Home" Panel, click on 'hardware and sound '.
  d. where it says 'Sound' in green letters, there are three options below that are in blue, click on "manage Audio devices.
  e. This will bring up a window titled "Sound".
  f. on the tab 'Read', he has listed the sound options at your disposal. It should read "peripheral digital output (HDMI)" click on it.
  g. There should now be a checkmark on this option.
  h. the sound should play through your HDMI connections to the TV.

  No sound in Windows

  http://Windows.Microsoft.com/en-us/Windows/help/no-sound-in-Windows

  Tips for solving common audio problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-fixing-common-sound-problems

• My system hangs during startup "for the first time" after running the system recovery.

  HP G62 - 227 CL

  Win 7 (64 bit)

  No error message, in itself; just a screen frozen on reboot.

  Months, my computer has suddenly started glitching on me.  I stopped and tried a reboot.  The system froze on start with flying colors.  System recovery tried several times but must have made a mistake because he wouldn't.  Resolved to buy a new hard drive and reinstall from the recovery disks.  Delayed unnecessarily until today, months later.

  Before you buy a new hard drive, has decided to relaunch the system recovery.  It worked!  I tried the option that has deleted everything and restored to the software and factory settings.  Everything seemed to work like a charm: hard drive reformatted, reinstalled software, the system prompted me to reboot.  Yes, I did.  Windows started to boot, "Preparting your computer for first use of Setup" appears... and freezes.  For hours.  Hard drive led is off.

  BTW, made sure the button Wi - Fi was on what I read on the problems of recovery if it was turned off when the program is run.

  Restarted.  Press F11.  A ran maintenance and checked the hard disk for errors.  There are errors.  Unfortunately, the default setting of CHKDSK does not repair them.   A opted for a command line.  RAND CHKDSK again with option '/ f/r' seen in other posts.  Here I am too ignorant to get the program to run properly, I guess.  I ran CHKDSK on the two player X and C.  No error found... sort of.  I know they exist because the system will not start.  (Yes, I tried again.)  Return to the command prompt, I tried to run CHKDSK on the drive C again.  This time I got a message that I must first dismount (remove?) the reader.  As I don't know what that means, I opted for the 'no' and have decided to post this help message.

  So.  Suggestions on what do I do then?  More specifically: How do CHKDSK to fix the errors it found?  I think the message was: "errors in $130 of the sector...". "It shows this message two times at the end of 62%.  Freezes for a long time.  Gets will still only slow down to a crawl again around 70%, but no longer.  Then returns to the start of system recovery screen.

  System recovery ran again for the pleasure.  Again, seemed to work like a charm.  Unfortunately, the laptop again sits frozen at "Preparing... for first use" screen again.  It heats more turns.  The audible fan works now plans higher... If none of this helps.  I am stopping and waiting for your advice.

  Thank you!

  Zac:

  My apologies for the delay to return to you.  Believe you that computer gremlins have not hit my very stable desktop which has been fine for years with sudden instability driver?  McAfee thanks for this most recent update!

  In any case, after several diagnoses and find the hard drive has failed in each of them, I decided to install a new copy of Windows 7 as a test while I wait for my upcoming recovery disks in the mail.  I did it by removing all partitions on the drive and do a fresh install.  Here again, everything seemed to go well until that (apparently) a certain area of the drive was used to save/installation of the files.  Even after CHKDSK runs several times (each time he repaired several defective sectors but stalled after only 10% of the disk) the system will become unstable - the last number being a blank screen after logging on to Windows.  So, all in all, epic fail on the side of the hard drive.  The new drive is installed and waiting for my recovery disks.

  Thanks for all your suggestions.  They have been a great help with information, but not with the results because of the training.

  M

• Laptop: cannot hear any sound from my computer

  My sound does not work in Windows 10. No sound at all from YouTube videos, music and media players, Windows system sounds, etc.

  The first step in troubleshooting I recommend is the easiest: restart your computer. Sometimes a single application can take control of your audio device and do not let all the other apps use, but you can release this control by restarting.

  Here are a few others not you can try:

  • Run the audio troubleshooting tool in Windows
  • Try to connect headphones or a pair of external speakers
  • Set the default audio device to make sure that your computer sends the audio output of the device
  • If your computer comes with 10 Windows installed, you can restore the driver of its origin in the HP Recovery Manager, or to update the driver through Device Manager
  • If you upgraded your computer to Windows 10, you can update the audio driver in Device Manager
  • Reset your laptop

  These solutions and much more are explained in detail in this document: laptops HP - no noise or distortion of the sound from the speakers.

• His error when I enter the first ('1') character in password wifi to printer MX470

  When I try to enter the wifi password to connect my MX470 to my wifi router, I get an error sound when I get the first character, which is be a '1 '. All other characters are accepted silently, but of course the password won't work without the '1 '. SO frustrating!!

  I found in the manual how to set the manual online how to set the keyboard entry

• Unable to hear the correct audio sound during playback of media

  Original title: Volume of the sound of my laptop gets strange

  My laptop sound weird during media playback. It sounds like something, for example to call someone on Skype, that happens so the volume is changed to adapt it, but I'm not turning them on. Almost all the video and audio will be faced with the problem of volume, sometimes it becomes normal after a while sometimes it does ' t. I turned the communications under off sound setting option, but the problem is still there. Please help me solve this problem, thank you!

  Hi Songqi Liu,

  This could be a hardware problem. However, I would check the issue by connecting to an external speaker to your laptop. Check if you are faced with the same question.

  Please an update on the status of the issue to help you further.

• Unable to hear sound during playback of music Web site Sampler

  Hello

  I am unable to hear any sound when trying to listen to samples of music on Amazon (for example) and also to other sites. I activated the firewall to all players of the internet, which is launch and start playing, but there is no sound.

  The volume is definitely on the speakers and I tried Windows Media Player and it plays radio and other music on my pc perfectly well. So I'm not sure about why I don't hear samples of music from websites now (I did in the past).

  An example of a link that has sample music is http://www.amazon.ca/Madeleine-Peyroux-Careless-Love/dp/B0002NRRAG

  Please can you let me know your opinion about this issue.

  Thank you

  Hello

  Have you checked whether the volume control of the sound wave and audio devices has been updated with higher level?
  This control is responsible for the volume of the music files.

• I have dv7 - 6B 63 and system sounds work but I can't hear any videos or music on the internet.

  Hi, I tried to understand why I get system sounds, but I hear no videos or music from the internet.  No matter what is the browser, or even if it is itunes.  I think it's so weird that I hear system sounds, but nothing else. I have an IDT high definition audio CODEC withd version 6.10.6418.0 driver.

  Thanks, Heather

  Try to install the latest driver IDT Audio take care of page:

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?OS=4063&LC=en&cc=us&DLC=en&sw_lang=&product=5197418#N229

• I can't hear any sound when you play a HDMI video uploaded to youtube, plays very well while on youtube but will not play sound from my hard drive after the use of realplayer download

  I can't hear any sound when you play a HDMI video uploaded to youtube, plays very well while on youtube but will not play sound from my hard drive after using the lplayer rea download

  Hello

  We will try to download different video using different downloader (other than RealPlayer) and see if the problem still persists.