I hope it's a matter of configuration base 4.5 FMS.

Similar Questions

• Voicemail configuration base with CUCM and connections of the unit

  Hello again,

  I'm still very new to CUCM.  I am configuring a CUCMB 6.01 test deployment.  He has connections in the integrated unit.  I have 2 DNs assigned to users and Cisco IP phones.  I use MGCP (Cisco 3745 with 2FXO as gateway).  Now, I'm trying to extensions of voicemail installation for the users.  I read a lot of documentation on CUCM and unity, but I know that Unity Express is not what I need, and that you have not found information on the basics of implementing voicemail for users of CUCM.

  Users are DN 1001 and 1002 respectively.  They are part of a list of hunting (broadcast) so that the arrival of incoming calls, both phones will ring simultaneously.  Not sure if this has any bearing or not.  I would like to be able to put in place so that each DN rings on the IP phone say 6 times, then go to a Unity voicemail box configuration for that user.  I have already imported users 2 in the unit.  I ran the voice messaging port configuration wizard.  Everything looks as if it runs correctly, but I'm stuck really share say CUCM to route the call to the mailbox of the unit.  Probably the simplest part.  Ideas or help on this would be much appreciated.  Thank you in advance.

  Impetuous salvation,

  CUCM works this way

  So the fact that 1001 and 1002 receive calls via a group has a significant impact on this config.

  You must keep in mind that a call that is routed through the fighter pilot will always ignore the CFWD settings on phones of hunting member of the group. The normal way to control it then is through disconnection of the Group Hunt members phones combined with the front fighter pilot level settings.

  The following section describes how the parameters to call it forward on the phones of individual members Hunt are ignored when presented a call via the hunting feature. Here's a clip;

  Hunting and call forwarding

  The concept of hunting differs from call forwarding. Hunting allows Cisco Unified Communications Manager to extend a call to one or more lists of numbers, where each such list can specify an order of hunting which is selected from a fixed set of algorithms. When a call extends over a part of hunting of these lists and the party does not answer or is busy, hunting resumes from the next part of hunting. (The next party of hunting varies according to the current hunting algorithm). Hunting has so ignore settings call forward No Answer (CFNA), call forward busy (CFB) or call before all (CFA) for the party to attempt (group member line phones).

  Cisco Unified Communications Manager offers the possibility to redirect a call when hunting fails (that is, when the hunt ends without a part of hunting to the respondent, due either to exhaust the list of numbers of hunting is to expire). If used, this final redirection includes an automatic call forwarding action. Therefore, the fighter pilot Configuration window includes call forwarding configuration concepts which are similar to those found on the directory number Configuration window.

  Example of a call hunt

  Although hunting is different from the transfer, Hunt often develops as a call that gets forwarded to a certain number of fighter-pilot. The protective cover of appeal extends from hunting to allow the final drive after two exhausts of hunting or expires.

  A typical call calling hunting can include the following phases:

  The appeal of hunting through groupings of posts set up according to the algorithms implemented for each group. Hunting is successful (if it meets a hunting party), exhausts (if all parts of hunting are tempted, but no response), or expires (if the deadline set by the Maximum hunting timer runs out before that all parties are tempted, and none of the parties who have tried to answer).

  For the purpose of this example, we assume that hunting does not succeed.

  If a form any of the final drive is configured, the call forward for a next destination; otherwise, the call is released.

  Maximum hunting timer

  The Maximum Hunt Timer field on fighter pilot Configuration window allows the administrator to enter a value (in seconds) to limit the hunting through a list of hunting season. After gaps in the time specified, if hunting was not successful, the call is transferred to a voicemail system, a specific compound number, or some personal treatment (if configured) or the call is released.

  The good doc.

  http://www.Cisco.com/en/us/docs/voice_ip_comm/CUCM/Admin/6_0_1/ccmsys/a03rp.html#wp1078922

  If the call goes unanswered or all Member phones are disconnected, then an attacker needs to be applied at the level of the "fighter pilot".

  Hunt the settings forward

  Before hunting without an answer - when did not answered the call which is distributed through the list of hunting at a specific time, this field specifies how to transfer the call.

  Destination this parameter contains the number of the directory to which calls are forwarded.

  Before busy hunt - when the call which is distributed through the list of hunting is busy at a precise moment, this field specifies how to transfer the call.

  Destination this parameter contains the number of the directory to which calls are forwarded.

  Maximum Timer Hunt - enter a value (in seconds) that specifies the maximum duration for hunting. (Used in conjunction with Forward busy hunting)

  In your case, it is best to configure the DN of a fighter pilot in the extension of alternatives under the 1001 and 1002

  mailbox.

  I hope this helps!

  Rob

• Best SSD & HDD configuration environment iMac 2010

  I put my 2010 middle level 21.5 "iMac with a 1 TB Samsung Evo 850 SSD. I'll use the OWC data backup kit to replace the optical drive in the iMac with the SSD. To feel pretty comfortable with the facility itself after having looked through the iFixit guide and various You Tube videos. My issue is with how best to configure the installed SSD.

  I use mostly the iMac for Lightroom CC and I'm under El Capitan.

  My 1 TB HARD drive and is full of about 80%. I want to use the SSD as boot obviously drive and also use it for all my applications. I just want all my old music files and RAW files on the HARD drive that I don't need to access often. There are about 300 MB of old RAW files, I can move on the HARD drive, then once as it is setup, I hope that I'll have to say 500 MB on the SSD and 300 MB on the HARD disk. As my RAW files grow I still move the old files on the HARD drive to keep the SSD to become too full.

  I had planned to restore all my files for the SSD from a Time Machine backup and then format the HARD drive before joining former RAW HARD drive files. But:

  -which is the best way?

  There's an easy way to achieve the same goal without keeping all my cruft?

  -going to have my HARD drive plugged complicated issues when restoring to the SSD?

  -should I use carbon copy cone instead?

  Any advice or suggestions appreciated.

  How to use an SSD with your HARD drive If you want to use an SSD as boot with your existing HARD disk drive, as the disk 'data', here is what you can do. After installing the SSD, you need to partition and format the SSD using disc utility disc. Then install OS X on the SSD. Once installed OSX boot from SSD. Startup disk preferences to set up the SSD as the boot volume. Open the preferences users and groups. Click the lock and authenticate you. Or CTRL - RIGHT click on your username account list in the sidebar and select Advanced Options in the context menu. You will see a field called "Home dir: ' on the far right, you will see an Edit button. Click on it. In the file dialog box, navigate to the location in house now located on the HARD disk (disk HARD/users/user_name /.) Select the folder, click the Open button. Restart the computer, as shown. When the computer starts, it will now use the home located on the HARD drive folder. Another more technical method involving the Terminal and the alias is discussed in depth here: using OS X with a SSD and HDD - Matt Gemmell configuration. It's my preferred approach because I can choose which records of the House, I want to on the HARD drive and I don't want to. For example, I like to keep Documents and library files on the SSD because I frequently access their content. Make sure that you keep the bootable system entirely on your HARD drive where you need it.

  Note that if you open the computer Apple won't provide any additional support if you need it. Make sure that you don't damage anything. Learn how to do what you plan to do before you start. It's a bad idea to try to learn along the way. There are small tablecloths at the back of the monitor that must be removed in order to access the disk space. There is also a special thermal cable required. I suggest you visit OWC where provide it a kit to add another disk to an iMac.

  You cannot copy OS X of your HDD to the SSD while leaving everything else behind. After installing the SSD you partition delete it, then install Snow Leopard top of your OS X disk installer supplied with the computer. After that, you can go to El Capitan if you wish.

  Clean Install of Snow Leopard

  1. start the computer using the Snow Leopard installation disc or disc 1 that came

  with your computer.  Insert the disc into the optical drive and restart the computer.

  After the ring, press and hold the "C" key.  Release the button when you see

  a small gear appear under the dark gray Apple logo.

  2. once the load setup program select your language and click continue

  button. When the menu bar appears select utility drive in the Utilities menu.

  After loading disk utility, select entry Out-dented the SSD in the list on the left.

  Click the Partition tab in the main window of disk utility.  Set the number of

  partitions to one (1) from the Partitions of the dropdown menu, click on the Options button

  GUID, click OK, and then select define the Mac OS Extended format type

  (Journaled), then click on the apply button.

  3. once formatting is complete utility of disk and return to the installer.

  Proceed with the installation of OS X and follow the instructions included with the installation program.

  4. Once installation is complete your computer will restart in the Setup

  Assistant. After finishing Setup Wizard will complete the installation, after which

  you will use a new installation of Mac OS X.  You can now begin the process of updating

  at the opening of updated software and installing all recommend updates to bring your

  current installation.

  Download and install Mac OS X 10.6.8 v1.1 updated Combo.

• How to configure redundant Bridging

  Hello

  A customer has a wireless (using bridges AIR-BR1410A-K9) as a connection link main beetween 2 offices. In the short time planned to add a second wireless link as a redundant connection.

  

  Documentation indicates the briding redundant (attached image) as an option for redundancy or load balancing, but no matter what configuration example is included.

  Does anyone of you have an example for this option?

  Concerning

  Hello

  one way, I've seen people do is to set up an eterchannel on the switches as if they were directly connected via a cable. The problem is that there is no granular fault detection, since it assumes that the link to AP + wireless + link to AP other side as only 1 cable. But you have the best load balancing.

  Redundancy without balancing is performed by connecting just the 2 links and have spanning tree configured protocols. The paper you gave explains how to configure STP on Chapter 8.

  Is there a particular point that additional information is needed?

  Kind regards

  Nicolas

• para procedure configures the antes of comenzar con instalacion del servidor vCenter Server database

  Hola y buenos dias, mi esta pregunta diriguida a como is has crear para vcenter en UN server remote sql database.

  Read el documento.

  http://KB.VMware.com/selfservice/microsites/search.do?language=en_US & cmd = displayKC & externalId = 1029061

  Pone in el apartado 8:

  Configure base datos antes comenzar con instalacion del servidor vCenter Server, a less than that to use the version of Microsoft SQL Server 2005 Express that viene con el instalador.
  
  Note: Los scripts for creating schema steps in the Microsoft SQL Server documentation y Oracle son opcionales y estan conducted a administradores experimentados of data bases. El instalador vCenter Server crea el scheme automatically if no anteriormente exists.
  
  

  • Microsoft SQL database
    
    • Use a script para crear UN database o local remota con una administrator cuenta Escalin base data. Optionally, the database can be created using SQL Server Management Studio from the same el formed as en version of vCenter Server 2.5
      
    • Configure una conexion ODBC type SQL Server. Cuando is instala el sistema vCenter Server, will you can set una conexion con una database SQL Server
      
    • Configure the Microsoft SQL Server JDBC para TCP/IP protocol. If el servidor SQL Server TCP/IP has not disabled y los puertos dinamicos no estan configurados, the JDBC connection permanent cerrada. Esto causa las and statistics of vCenter Server dejen funcionar.
      

  Como no voy a usar the espress, tengo that create db manualmente, habla los scripts? not los encuentro in el DMC, por lo tanto donde puedo encontrarlos having into account that voy a instalar Vcenter 4.1U1 en UN 2008 R2 y el otro 2008R2 is sql y su version are sql2008R2

  a greeting

  Hola irasines:

  Como ha well said piaroa, el usuario crea y el of database in SQL e instala client el nativo donde vayas a instalar para vCenter connected contra base data. Run las credenciales y seleccionas the database there are el is encarga crear el completo scheme.

  Todos moderators puedes seguir el documento ESXi Installable and vCenter Server Setup Guide from page 51.

  A greeting.

  --------

  José Luis Gómez Ferrer de founder Couto of PiPo e2H Blog: http://blog.e2h.net

  If upon that esta otra respuesta utility fue, por favor any o da el voto. Gracias.

  If you find this or any other useful answer, please consider awarding points. Thank you.

  

• Qosmio G30 - black screen on external monitor

  Qosmio G30 (PQG32E) under Vista Home Premium, driver NVIDIA GeForce Go 7600, 7.15.10.9813

  I can't get a picture on a monitor external (I tried two different monitors). More precisely:

  "Windows Mobility Center" will recognize that a monitor is connected
  "NVIDIA Control Panel - Display Change Configuration" will recognize the external monitor ('Select poster that you want to use' shows 'Display of the laptop + Sony SDM-HS73', which is the monitor plugged in ext)
  but no matter what configuration I try using Fn + F5 or change of display Configuration, I can't do anything but a black (backlight) display on the external monitor.

  The monitor is receiving a video signal correctly: when he is off in laptop only the setting Fn + F5, it displays a warning 'no signal', but when turned on again I just get black.

  I tried to change the resolution for the external monitor settings. They exactly match the native resolution of the monitor. Still nothing.
  I tried 'Clone' and 'Dual View' mode.
  Tried various different orders to turn on the computer laptop and monitor, Plug and unplug the device, etc.

  Having installed the latest driver for the Toshiba (see above) site. Have NOT tried to install any other driver from NVIDIA site, as she warns to use Toshiba - but that's worth a try?

  The clean laptop screen and all other aspects of the video are very good.

  It worked ok in the past (I think that before I did the upgrade to Vista when it was still on XP).
  Should I just wait for another update of Toshiba driver and maybe Vista SP1?

  I really hope this isn't a hardware problem, because the monitor is recognized etc...

  Jonathan

  What port you used?
  The (analog) external monitor port or the output port D-video?

  View as far as I know that if you used the external monitor (analog) port, then you should choose analog in the nVidia-> current view

  Then, you can use the FN + F5 key to switch between the two views.

• Bug sequence editor - dynamically rename steps

  I discovered a problem with the 4.2.1 pecular the Editor display sequence of steps that should be called dynamically at run time. It might be present in other versions, but I have no way to check. I had this experience with Windows XP and Windows 7.

  I've attached an example which is very easy to reproduce the problem. It does not matter what Configuration of list stage you are in.

  (1) create a new sequence

  (2) create a step declaration type

  3) switch to the view of Expressions within the parameters of the step > component property

  (4) in the Expression before, type RunState.Step.Name = Str (Find (RunState.Step.Name, "t"))

  * In theory, when you perform this step it will rename it to the position where it finds first a 't', 1.

  (5) (while in the view of Expressions within the parameters of the step > property pane), the step of copy and paste several times.

  (6) TestStand must lock the right for you. If not, stick a few times or cycle (quickly) between different steps see two.

  It is not only limited to the Expression, and it seems to happen less, if you view the step settings > expressions pane, but it always seems to lock to the right. If you are in another mode (which does not appear the expression) it seems not to happen

  I guess what happens is when TestStand attempts to check the expression to find errors is to get caught in an infinite loop if you recycle too quickly. However, I don't know how to work around this problem, other than slowly of switching between the steps if I consult their expressions with the concept of recursive naming.

  I would like to know if this has been documented before, if it has been resolved, and if there is a better workaound.

  Thank you

  Mike powers

  Control of the expressions in the expression of the syntax controls is performed asynchronously in another thread when the control of the expression containing the phrase is visible (i.e. the parameters of the expression for the expression before in your use case, are active in the step settings pane). You hit a blocking problem that has been fixed in TestStand 2012 (number 287875).

  You can work around this problem, either avoiding having the control of the visible expression while making the dough, or, in the case of your words at least. You can rewrite it as follows:

  RunState.Step.Name = Str (Find (NameOf (RunState.Step), "t"))

  The deadlock occurs for your particular situation due to the use of the API in the expressions for an argument to Find(). NameOf() is another way to get the name of an object without using the API in expressions.

  Hope this helps,

  -Doug

• generate a digital triggering out CH1 (low and high) for the USB-5133

  Hello

  I would like to generate a digital triggering on the USB 5133 CH1, is this possible?  I tried with the PFI 1 successfully but the output is only 3.5 v and I need to 5V, because this trigger signal goes to a box of pulse generates a signal, which is received by the CH0 on the USB-5133. This configuration works on the 5102 OR but because of the treatment, I am obliged to try a new device.

  Channel 0 and 1 are only entries then you will not be able to use them to generate a signal.  All of our products current digitizer that are recommended for new designs use 3.3V CMOS logic levels for PFI lines in output mode.  Your best bet to generate a digital triggering 5V would be to use an external buffer that can accept 3.3V CMOS levels as an input, but is under voltage of 5V.  Here are some that might work for you, but there are many others: http://www.onsemi.com/PowerSolutions/product.do?id=M74VHC1GT126DT1G adding a buffer in line with the trigger signal will add delay, so you will need to ensure that it is acceptable for your application.

  Hope this helps,

  -Matt

• How to synchronize two chassis

  Dear all,

  I want to synchronize two chassis, chassis first has RFSG 5673E (S) and other chassis a DAMA (S) 5663E, they are connected via MXI, is there anyone who has this experience and can support me to apply it. I know that he used NI-Tclk to synchronize in a single chassis and there is another kit of tools for mult chasis, but I have no idea on how to use it!  Thanks in advance

  Best regards

  Al-Rawachy

  So I did a little research and to allow you to synchronize the two chassis together you must use a map of timing and synchronization in each frame so that you can share Tclk. This is for several reasons: first of all, as well as terminals IN CLK and CLK OUT, several PFI lines are required for the export of various signals used by T - CLK (i.e. Start, Stop and Sync triggers). In addition, the map of timing and synchronization is also necessary to replace clock background basket of 10 MHz, on the chassis of the slave with the master clock. It is essential for the two hunts reference the same clock synchronization. In addition, using a more stable clock source, as provided for in the calendar and map of synchronization, improve synchronization significantly.

  From there, a chassis are sync'd up, TCLKing la 5665 and 5673E should be simple enough. It should be simply a matter of configuration tasks the DAA and RFSG, with a single trigger configured, before feeding the two tasks of the TCLK vi. Here is an example for you to study what explains this:

  http://www.NI.com/example/30254/en/

  I hope this helps.

• EliteBook 8760w: can I put my EliteBook 8760w with an mSATA SSD hard drive using the slot mSATA

  I wonder if it should be possible to use an mSATA SSD by installing it in the slot mSATA?

  Product number: LG673EA #AK8 (EliteBook 8760w)

  I inserted an mSATA SSD and it fits, but after booting, the computer gives the following message:

  No wireless module supported

  The system has detected the wireless installed in the system module is not supported and disabled.

  WWAN Module ID (703)

  I hope it's just a matter of configuration/drivers, etc...

  No, it's a physical barrier. Is the accommodation that you turn the player mSATA in p.50 indicated on the manual here? :

  Repair manuals

  This port is a card WWAN (cellular modem) only. Your laptop is the Intel Core 2d era generation and utilization of disks mSATA even for cache acceleration did not really catch up to the 3rd generation. The circuits to see and make use of the mSATA drive is simply not present in this laptop. I'm sorry.

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• Newly installed Intel SSD recognized but not accessible

  I have Vista 64 with all updates. I just installed a new Intel 160 GB SATA SSD.

  My homebrew system with an i7 processor in a card mother Asus P6T.

  The new command is correctly identified by part number in the list of hard drives and under "Drives" Bios Vista Device Manager, so that the reader must be properly powered and communicate, but it is not present in the list of drives available when I select "start > computer.

  Useful suggestions would be appreciated.

  Read the following article and see if it lights up the whole problem - maybe you missed a step. http://www.easeus.com/resource/install-sata-hard-drive.htm.

  Go to start / Control Panel / Admninistrative tools / computer management / disk management and see if you can see the SATA drive it.  If so, it may just be a matter of configuration and formatting if you see the operating system.  The above article which addresses in detail.

  I hope this helps.  Keep me in the loop.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• WebWorks Push Client

  Hello

  I'm sort of stuck in the logical process to receive a push message in an application webworks. The sample application works fine and I can receive messages with him. I guess I understand something wrong.

  What I understand so far is:

  1. create pushservice

  2. create the event listener

  3 activate the application to launch on push

  4 create the channel

  and everything should be good... or not? Lets talk about code:

  config. XML (part)

  
      post_notification
      _sys_use_consumer_push
      read_device_identifying_information
  
  
      APPLICATION
      
          bb.action.PUSH
          application/vnd.push
      
  
  

  JavaScript :

  function createPushService() {
    try {
  
          ops = { invokeTargetId : 'bert.pushcapture.invoke.push',
                  appId : 'XXX-XXXX...',
                  ppgUrl : 'http://cpXXX.pushapi.na.blackberry.com'
          };
  
          blackberry.push.PushService.create(ops, successCreatePushService, failCreatePushService, onSimChange, onPushTransportReady);  
  
    }
    catch (err) {
      alert(err);
    }
  } 
  
  function successCreatePushService(service) {
      //alert("Created Push service");
      // check this **bleep**
      pushService = service;
      blackberry.event.addEventListener("invoked", onInvoke);
      launchApplicationOnPush(true, launchApplicationCallback);
  }
  
  function failCreatePushService(result) {
      alert("Error: Received error code (" + result + ") after " + "calling blackberry.push.PushService.create.");
  }
  
  function onPushTransportReady(result) {
      if (result == blackberry.push.PushService.SUCCESS) {
                  alert("successful Configuration");
          } else {            
  
              if (result == blackberry.push.PushService.INTERNAL_ERROR) {
                  alert("Error: An internal error occurred while calling launchApplicationOnPush. " + "Try restarting the application.");
              } else if (result == blackberry.push.PushService.CREATE_SESSION_NOT_DONE) {
                  alert("Error: Called launchApplicationOnPush without an " +
                  "existing session. It usually means a programming error.");
              } else {
                  alert("Error: Received error code (" + result + ") after " + "calling launchApplicationOnPush.");
              }
          }
  }
  
  function launchApplicationCallback(result) {
      if (result == blackberry.push.PushService.SUCCESS) {
                  alert("successful Configuration");
          } else {
  
              if (result == blackberry.push.PushService.INTERNAL_ERROR) {
                  alert("Error: An internal error occurred while calling launchApplicationOnPush. " + "Try restarting the application.");
              } else if (result == blackberry.push.PushService.CREATE_SESSION_NOT_DONE) {
                  alert("Error: Called launchApplicationOnPush without an " + "existing session. It usually means a programming error.");
              } else {
                  alert("Error: Received error code (" + result + ") after " + "calling launchApplicationOnPush.");
              }
          }
  }
  
  function onSimChange() {
      alert("SIM card is changed!");
  }
  
  function createChannelCallback(result, token) {
      if (result === blackberry.push.PushService.SUCCESS) {
          alert("channel created");
      } else if (result === blackberry.push.PushService.INTERNAL_ERROR) {
          alert("channel failed");
  
      }
  }
  
  function onInvoke (invokeRequest) {
          if (invokeRequest.action != null && invokeRequest.action == "bb.action.PUSH") {
              if (pushService == null) {
                  setTimeout(function() { onInvoke(invokeRequest); }, 750);
              } else {
                  var pushPayload = extractPushPayload(invokeRequest);
                  pushNotificationHandler(pushPayload);
              }
          }
  }
  
  function pushNotificationHandler (pushpayload) {
      var contentType = pushpayload.headers["Content-Type"];
      if(!contentType) {
          contentType = pushpayload.headers["content-type"];
          if(!contentType) {
              contentType = "text/plain";
          }
      }
  
      db.transaction(
          function(tx) {
              tx.executeSql("INSERT INTO Data (title) values(?)", [ "PUSH"], null);
          });
  
      //alert("PUSH RECEIVED");
      pushpayload.acknowledge(true);
  
  };
  

  I call following functions thanks to a button:

  1 createPushService();

  2 pushService.createChannel (createChannelCallback);

  and I get a 'alert ("channel created");"and it means to me that the PushService and the channel was created successfully.

  Given that I have create an event for a 'called' via 'blackberry.event.addEventListener ("called" onInvoke),"the"onInvoke"function should be called when receives a new thumb. Fix?

  Unfortunately it does not work and I get no response or error.

  Any help or advice is appreciated. I'm really stuck here...

  The best

  bert2002

  Hello

  A couple of things to ask you.  Not sure if they are related to your problem, but it's worth a shot.

  1. you call extractPushPayload below when dealing with a thrust to invoke.  But, when this function is defined?  You must call pushSevice.extractPushPayload somewhere.

  2. you should not the setTimeout function need more if you add the event listener for the "called" event in your call to success blackberry.push.PushService.create.  Our sample no longer use setTimeout.

  3. in your code, you call launchApplicationOnPush and createChannel every time.  You only really need to call them once.  After graduating launchApplicationonPush and reminders of createChannel successfully the first time, then you are ready to receive the impulses.  You just do it again if you make a destroyChannel somewhere.  Do you need to call blackberry.push.PushService.create each time however.

  4. are you setting the tag in your config.xml file?

  Hope that helps,

  Matt

• Adding compression to PLM4P

  Hello everyone,

  Anyone here had any experience compress components with gzip and expires headers in the web configuration file?  I did it and it seems to work, but I want to assure you not miss me something that might be affected by these changes.  I turned on the static and dynamic compression.

  Thank you

  Hi, Mike.

  If you're talking about thePLM4P_HOME\web\ \web.config files, then these will be crushed with each version, and you need to reapply the changes.  unless you are using a shared hosting server and you don't want to or cannot enable compression for all, it would be better to change the compression in IIS (using appcmd to modify the metabase.xml file) instead of directly modify the web.config files.

  also, do not know what file types that you add expire headers for, but IIS 7.x hiding some default file types, including image, css and js files.

  all that being said, Yes, it is strongly recommended you use compression, be it in Internet Information services or upstream device.  If IIS, I would recommend setting the compression level 8 or 9.  This will give you the best compression without being too CPU taxing.

  hope that helps,

  -Matt

• How to change back to SSD HARD drive?

  My mcbook pro comes with the original 500 GB of HARD drive. When he ran with a problem, I went to an apple repair shop. Problem was in the charts, and he suggested the HARD drive to be replaced by a 120 GB SDD. So it has been replaced, but the guy on the left HARD drive as a storage device. Moment where DDI is left with small space and when I update to OS X El Capitan of OS Sierra, it had to be installed in the HARD disk drive. Could someone please give instructions to install the new OS to the SDS to lose all my data and the current configuration and it is also possible to install windows XP on the HARD drive and 10.  Either by the way, I got Windows 10 and XP shared with the SDS via parallels. Thank you

  I think this can be useful for you:

  How to use an SSD with your HARD drive If you want to use an SSD as boot with your existing HARD disk drive, as the disk 'data', here is what you can do. After installing the SSD, you need to partition and format the SSD using disc utility disc. Then install OS X on the SSD. Once installed OSX boot from SSD. Startup disk preferences to set up the SSD as the boot volume. Open the preferences users and groups. Click the lock and authenticate you. Or CTRL - RIGHT click on your username account list in the sidebar and select Advanced Options in the context menu. You will see a field called "Home dir: ' on the far right, you will see an Edit button. Click on it. In the file dialog box, navigate to the location in house now located on the HARD disk (disk HARD/users/user_name /.) Select the folder, click the Open button. Restart the computer, as shown. When the computer starts, it will now use the home located on the HARD drive folder. Another more technical method involving the Terminal and the alias is discussed in depth here: using OS X with a SSD and HDD - Matt Gemmell configuration. It's my preferred approach because I can choose which records of the House, I want to on the HARD drive and I don't want to. For example, I like to keep Documents and library files on the SSD because I frequently access their content. Make sure that you keep the bootable system entirely on your HARD drive where you need it.

• Upgrade SSD for Macbook Pro?

  I have a Macbook Pro (early 2011) and I would like my mac by installing a SSD 15'. He got a 2 GHz Intel Core i7 processor. My laptop started to slow down a lot and it lags when I use photoshop or when I'm editing videos, so I thought I should spend my hard drive for an SSD. But I don't really know what SSD to buy it. My friend recommended the Kingston SSD UV400, but I read that some people have complications after installing the SSD on their Macs. I really don't know much about these things, I'm looking for insight. Someone at - it recommendations for SSDS, I should get? I'm looking at a minimum of 480 GB for storage and, ideally, something lasting!

  Thank you very much!

  Currently, the best options are the OCZ ARC-100 series, the 850 series of Samsung (good price on Amazon) and 6G OWCseries. OWC also has tool boxes if you need it and installation tutorials. If you want to keep the HARD drive then you buy one of their media DataDoubler to put the old HDD in the space occupied by the optical drive. It can even include an enclosure for the optical drive.

  How to use an SSD with your HARD drive If you want to use an SSD as boot with your existing HARD disk drive, as the disk 'data', here is what you can do. After installing the SSD, you need to partition and format the SSD using disc utility disc. Then install OS X on the SSD. Once installed OSX boot from SSD. Startup disk preferences to set up the SSD as the boot volume. Open the preferences users and groups. Click the lock and authenticate you. Or CTRL - RIGHT click on your username account list in the sidebar and select Advanced Options in the context menu. You will see a field called "Home dir: ' on the far right, you will see an Edit button. Click on it. In the file dialog box, navigate to the location in house now located on the HARD disk (disk HARD/users/user_name /.) Select the folder, click the Open button. Restart the computer, as shown. When the computer starts, it will now use the home located on the HARD drive folder. Another more technical method involving the Terminal and the alias is discussed in depth here: using OS X with a SSD and HDD - Matt Gemmell configuration. It's my preferred approach because I can choose which records of the House, I want to on the HARD drive and I don't want to. For example, I like to keep Documents and library files on the SSD because I frequently access their content. Make sure that you keep the bootable system entirely on your HARD drive where you need it. [Permission to use any part of the foregoing has been granted by khati, exclusively, to theratter.]