I'm not sure my question got by and I scored to send me an answer. is it ok?

Similar Questions

• not sure if it's SFF and USFF

  Dear Sirs

  I want to buy a graphics card for my Dell optiplex 780 computer to activate the features of OpenGL 3D PhotoshopCC.
  I don't know if I have is SFF or ULTRA-COMPACT. Details of my PC are the following:

  SERIAL #: HFD3CP1
  EXPRESS SERVICE CODE: 37934283781
  REG MODEL: DCCY1F
  ASSEMBLED IN MEXICO
  LABEL P/N: 58W43 A00

  I'm very grateful for your kind information regarding the clarification of the SFF/USFF
  Furtherand that are for this PC with 235W power graphics cards and its 16 express slot

  Configured as follows:

  4 GB (2 x 2 GB) ddr3 memory
  1 320 GB hard drive
  1 set of DVD
  1 pci wiFi card

  Thank you best regards n
  IFFI

  GeForce 210 64 bit card is part of a series of maps that will be end of end of life of the media from April 2016.

  http://NVIDIA.custhelp.com/app/answers/detail/A_ID/3473

  Radeon 5450 or 6450 is 1 Gig of video ram is recommended not only because it consumes less energy, but because his support in windows 7 8 10 because its much more recent directx 11 card.

  ASUS EAH6450 has no fan and low profile fits all model dells except USFF because USFF has no slots.

• Document does not print, but directly goes thru and then I get the message in paper.

  Hello everyone, I recently bought a HP Deskjet 3511 e-all-in-one printer and after initial installation I it used once to print and it worked perfectly.

  I went to print a document today and put in operation the printer, went in the document folder and opens the document that I wanted to print and when I pressed the "print" button, the already loaded book spits 2 pages print watch then showed the "out of paper" message when it is not paper.

  I powered market, unplugged, reloaded diagnosis paper, I tried and I have the same problem.

  What could happen that it will not show the paper as load and print correctly, thank you for your answers.

  I tried the solutions... ended up sending back. as I had warranty... Buy a new... and already have my refund...

• I forgot my password and not sure of the answer to my secret question so impossible to singin' or reset the password

  Hey there, I got my password of windows live account * address email is removed from the privacy *, I'm also not sure of the answer of the secret question... but my what is important, I still have access to my email in this account, and I think it would be useful to reset my password accouns, HELP

  Please carefully follow all of the steps on the Recovery Windows LiveID account Help Page.

  Sorry, we can not help you with your Hotmail account number in the Microsoft answers Forums.

  Kind regards.

• I got a message this morning, and I'm not sure I did the right thing. He asked something about airports or restaurants?

  no problem with Mozilla. I just got a message on safety and use in airports and restaurants. I unchecked something. I'm not very savvy computer. I don't want to spoil anything. Sorry I can't be more helpful.

  I am afraid that we cannot help you if you are not sure of what the message was. I suggest that you try to run some scans on your computer to search the software malware, Troubleshooting Firefox problems caused by malicious software

• I have a proof of purchase of my Adobe CC license, but according to the site and the app I'm in a free trial. I just got a new Mac and everything transferred and has been using the application on an old PC for a while so I'm not sure is this is what is ca

  I have a proof of purchase of my Adobe CC license, but according to the site and the app I'm in a free trial. I just got a new Mac and all transferred to an older Mac and has been using the application on an old PC for a while so I'm not sure is what is causing my problem. I have bank statements indicating payments of my subscription to Adobe for this product update.

  Hi Seth,

  First of all, disconnect, then back into creative cloud, using adobe id to pay for your subscription.

  https://helpx.Adobe.com/creative-cloud/help/sign-in-out-activate-apps.html

  Then, if you launch any product of CC 2015 and the pop up still shows a trial message window, please check this link for the resolution:

  https://helpx.Adobe.com/manage-account-membership/CC-reverts-to-trial.html

  Hope this helps!

• My computer says that the battery is "plugged not charging" I just got a new. Any ideas how I can solve this problem?

  My computer says ' plugged not supported "I just got a new battery... How can I fix?

  Hello

  You should really be asking in the forums for your version of Windows. Click on the
  Appropriate forum in the Menu bar under the Logo of answers on the upper left on
  This or any page.

  Answers - Windows Forums
  http://answers.Microsoft.com/en-us/Windows

  ---------------------------------------------------------------------------------------------------------------------

  Are you sure that the battery is compatible with your system?

  References to Vista also apply to Windows 7.

  Check with support from the manufacturer of their books online and the drivers and their forums system
  (as applicable) for known issues. Some manufacturer issued BIOS and other updates to help the battery
  problems.

  =================================================================

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  Then run checkdisk (chkdsk).

  How to run check disk in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  =================================================================

  Other information that might help:

  Control Panel control - plan change Options - power plans - power - advanced settings
  Parameters for the drainage and the use of parameters (this is how much to use and not how much or how)
  long to load).

  In fact, what causes a lot of wear on a battery empties it too low on several occasions. With today
  systems overload are not a problem.

  Here are some tips to help and troubleshoot battery issues.

  Old battery? Unplug the power to the computer - remove the battery and clean the contacts with a pencil
  eraser (do not use this, if your battery is fine slots - just clean up the edges of the knife which fit in)
  them and be careful). Batteries are old, or it could be a problem with the computer.
  Check with the support of the machine system, and many of them have on line forums.

  New Lithium-Ion type battery usually last longer if you do not unload their less than 30%
  However on a laptop that not extend their life a lot. Best is to use the a/c adapter
  When this is possible.

  I use the free version of BatteryBar to monitor my battery. Click on the green button on the
  Yellow box on the right side of the page to download the latest stable version.

  BatteryBar - free version available
  http://osirisdevelopment.com/BatteryBar/index.html

  Another good program

  Vista battery saver - free
  http://www.codeplex.com/vistabattery

  Problems with the lives of its use and the battery of power - Mr Fixit
  http://support.Microsoft.com/GP/windows_battery_power_settings

  You can also check with the manufacturer of system and forums that many use their own
  proprietary software to monitor the battery and they could be known problems with your battery.

  ============================================================

  Battery meter: frequently asked questions
  http://Windows.Microsoft.com/en-us/Windows7/battery-meter-frequently-asked-questions

  Battery saver
  http://Windows.Microsoft.com/en-us/Windows7/conserving-battery-power

  Solutions to common battery problems
  http://Windows.Microsoft.com/en-us/Windows7/solutions-to-common-battery-problems

  What is the precise the battery meter?
  http://Windows.Microsoft.com/en-us/Windows7/how-accurate-is-the-battery-meter

  ============================================================

  Try this - to make a Restore Point

  How to create a System Restore Point in Windows 7
  http://www.SevenForums.com/tutorials/697-system-restore-point-create.html

  How to do a system restore in Windows 7
  http://www.SevenForums.com/tutorials/700-system-restore.html

  Then Control Panel - Manager of devices - Batteries - Double click on each item - drivers - tab
  Update the drivers (which can do nothing) - then do a right click and UNINSTALL each - RESTART
  who will update the driver stacks.

  Problems with the lives of its use and the battery of power - Mr Fixit
  http://support.Microsoft.com/GP/windows_battery_power_settings

  I hope this helps.

• MacBook Pro will not initialize. Question Mark flashing folder

  -Macbook Pro 13 "Unibody model 2009

  Hi guys,.

  I have been a frequent visitor to the community of support here, but I'm a poster for the first time, so please forgive any lack of post I suffer from the label. I saw this problem here much and seem me to always see the same advice to fix, but I have never seen anyone who treat the same symptoms I had with my camera.

  My question all started when I tried to save something for the reader, and he said to me "you are not allowed to save this destination" (something to that effect). Then it progressed to a question on my Macbook to spontaneous freezing. It would freeze just constantly and I always have to force offshore. When I would try to start the machine up, it's always 50-50 chance that it should start successfully, often welcomed by the famous question mark flashing folder. I constantly by visiting an Apple store for the last year and a half on this topic and after countless visits, they insist that there is no problem that they can find. They always say down to "permission error", problems of BONE that have been resolved by resettlement and a faulty hard drive. I've dealt with them during this period and and still have this machine properly repaired on any occasion. The problem persists always just after I take the machine home and start right away, its still there.

  As time went on this issue, I noticed that the machine would often freezing when moved, for example moved a table at my knees etc. This has some time until that I have raised to clean the table under one day and then tried to do turn on and nothing. The machine refused to start, only to give me the question mark flashing folder. I tried to boot into recovery mode by using CMD - R and tried to reinstall the OSX, I read that it is a common solution, but whenever I start recovery mode "Macintosh HD" is not where. So I can't even try a reinstall of OSX.

  A man IT in my former work place had examined this issue before on another machine, and he said he had replaced the cable of HDD of the machines as the previous was damaged. When toggled, he said that the machine was working fine. It would be logical, as if the cable is already damaged and loose, I'm sure that the movement might just disconnect. I raise this issue because it is of NEVER once offered all the time, I in dealing with this issue and on further investigation in the apple forums and this seems to be a very common problem.

  

  This appeared on a boot up once and never since.

  

  And that's what I see at every boot up to now.

  I'm sorry to bombard all the world with so much information on this subject, but my frustration is quickly turning into madness on this issue, which have no one at Apple after countless visits being able to fix the problem. As it is the main culprit for me, the HARD disk cable, but I would not assume know better that some of you have known many more people.

  Any information or help that guys could pass my way would be greatly appreciated I was apparently no help from Apple repair personnel. If you have read and thought about all this I applaud you and owe you a drink at the mercy.

  James

  MacBook Pro

  Hi Yogi Wynne:

  I agree with your friend IT. Looks like the SATA hard drive cable has problems.

  The inside of your computer is not as smooth on the outside and rubs it hard against the SATA cable and can cause one of the traces in the short cable is causing hard drive problems.

  Here's where you can get a replacement cable, they are very fragile. https://www.iFixit.com/store/Mac/MacBook-Pro-13-inch-unibody-mid-2009-mid-2010-H ard-car-Cable/IF163-013-1

  Here's a video that shows what could happen. https://www.YouTube.com/watch?v=Amg5w0rlwDo

  I might change the SATA cable and see if the problem persists.

• not sure: the new hard drive installation

  I have a Desktop allows a hard disk which is a failure.  F9 during boot diagnostics say its bad.  I just got the HP recovery disk and I'm not sure that 'when' to instaqll them.  I put the OS on the new hard drive and then first run the recovery or recovery disk?

  If you have the recovery disk set for this PC, run recovery on the new hard drive.  To install everything back like it was new again.  The installation of the OS process is executing the recovery.  Install the new hard drive, and then run the set of recovery disks.

• Not sure what type (Variant) to wire in Datasocket read to a waveform.

  Hello

  I have an accelerometer attached to a housing NI USB-6008 and I try to send the readings taken with it to the server datasocket, (see attached files).  I'm not sure what information and variables are necessary to be wired data read vi (Variant) type so that it displays the information on a waveform graph.

  The accelerometer is just by the way an analog voltage.

  Any help appreciated.

  Hi Ultramar,

  How Datasocket got out before the dynamic data Type was created, it doesn't have full support for this type of data. There is an easy solution that you can apply, which converts the DDT into a table 1 d of waveforms. Screw seal (in the zip file) will show you how to proceed.

  You will also need to add an element named 'test' for Datasocket Server Manager, I've included a settings file, you can import into the DS Server Manager.

  Finally, you will need to run the DS server and you will get the communication.

  I wish to indicate that the 6008 is not the best map to read the values of acccelerometer, but the above steps will allow you to send the data. You will need to change the physical hardware DAQ channel in the publisher.vi DS because I modified the DAQ assistance to work with my setup of the computer.

  Concerning
  JamesC
  NIUK and Ireland

  It only takes a second to rate an answer

• Problems connecting to internet - says network cable disconnected, not sure I have the correct driver installed.

  Had a big storm - got the new modem.  but they said that my drivers where missing or damaged.  Downloaded Marvell Yukon of gateway - to the GT5432 model. Always says cable unplugged network. However, Bishop says peripheral device works correctly. Don't save: no update-unable to connect to the internet.  I uninstalled and reinstalled; rebboted, etc. - still nothing. It has a problem with the PCI connection - no driver, but I don't see anywhere to down load or know what to download. Oh and another adapter on - think 1394 - when I turn that on and off the wonder; It shows the signal for the 1394---400 and does not say his unplugged, but still can not connect to internet.
  The "old" computer to try to find information; noticed that said, unplugged network cable but it allowed me to connect to the internet. When I disabled the 'extra' adapter message there went, speed signal only at 100 than at the 'old' calculation is not any other PCI devices connection listed.

  I'm not sure of what continues.

  The 1st computer was working fine - then picked it up to move it to where it belonged to my office and that's when he went out-made no sense to me!

  Because you seem comfortable opening your computer, have you tried re - a corner of the map (with power off, remove the card and reinsert it into the slot, be sure to exercise static precautions if you are in an environment of low-hu7midity).  If there is an empty slot, you can also move the map Marvell to another location.  See the comments below.

  It's a long shot, because even if you did not provide the complete ipconfig output, the data that you have provided appeared to be normal, but...

  Open network connections (start > run > ncpa.cpl > OK)
  Right-click on the icon for your network adapter, and then select Properties
  You should see a screen like this--> http://screenshots.modemhelp.net/screenshots/Windows_XP/Network_Connections/Local_Area_Connection/Properties/General/Index.shtml
  Issues related to the:
  In the upper area, under 'Connect using' said 'Marvell Yukon 88E8039 PCI-E Fast Ethernet Controller?  If this is not the case, what does say?

  In the second box, what are the items are listed under "this connection uses the following items"?

  The only other thing I can think is that the Marvell Ethernet card was damaged in the same storm that got your original modem/router.

  *******************************************

  According to Gateway, the GT5432 has 4 card slots:
  A PCI Express x 16 (GUI)
  A PCI Express x 1
  Two PCI Conventional

  Your motherboard should look like this:
  

  Orange, top, connector is the PCI Express x 16.  You probably have a video card in this slot.

  The short white connector is the PCI Express x 1 connector.

  Two more long white connectors are the standard PCI slots.

  If I understand your installation, you should have the Marvell Yukon map into the slots of two down and your Agere modem on the other.  As long as you have the SMC1244TX PCI card, why don't just remove you the Agere modem or the card Marvell and insert the card CMS in one of the two PCI slots?  You are not using the modem and the working hypothesis is that the Marvell card does not work, so there is not much to gain by leaving a card in your computer.

  Download the user guide and drivers for the SMC here--> http://www.smc.com/index.cfm?event=viewProduct&localeCode=EN_TUR&cid=9&scid=51&pid=238 map

  Moreover, assuming that your open slot is the short PCI Express x 1 slot, you can buy another Ethernet card that will work in this niche: see--> http://www.newegg.com/Product/ProductList.aspx?Submit=ENE&N=100010064%20600016290&IsNodeId=1&bop=And&Order=PRICE&PageSize=100

  If I were you, I blow up the cheaper models and get the Intel EXPI9301CT $ 36 10 / 100 / 1000 Mbps PCI Express Desktop Adapter Gigabit CT.  Note that this is the same card with a similar name (with close to 400 customers) which sells for $29,94.  The price difference is because the cheaper "BLK" letters in the description, which means that it is "sold in bulk" and has no drivers, user guide CD or anything else in the box.  There are several negative comments from people who do not understand this difference and then had trouble finding the driver for the card on the Internet.

• I need a new Image of XP because my expired original but when I downloaded it again, the new XP said its has expired, too! I thougt of caching problem of virtual machine manager, but I'm not sure.

  VHD expired

  http://t.co/exzliimb - where I downloaded the XP VHD of

  http://t.co/8vhbKuzu - error screenshot

  I need a new Image of XP because my expired original but when I downloaded it again, the new XP said its has expired, too! I thougt of caching problem of virtual machine manager, but I'm not sure. I deleted all the VHDs before you download again. Any ideas?

  Hello

  Your Windows XP question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the Technet Forum. You can follow the link to your question:

  http://social.technet.Microsoft.com/forums/en-us/w7itprovirt/threads

  Hope this information helps.

• I ran the upgrade wizard. I'm still not sure what it means

  Hello

  Preamble: I'm not tech savvy, please he dumb down for me.

  I ran the upgrade wizard and I'm still not sure if the upgrade is a good idea. I need to know whether or not it is compatible before moving with her.

  I have a Dell Inspiron 1525, running Windows Vista.

  Some issues that came:

  Install an application to play DVDs, Sidebar gadgets are not supported, secure boot is not compatible, your screen resolution is not compatible.

  I checked my screen and higher resolution, it goes up to is 1280 X 800. I tried to watch promotional videos for Windows 8, but the video does not work yet. The color was off, the sound was very good.

  What does that mean? Windows still work? What should I do to make sure that I can still do normal things?

  I do not know. You will need to check with the Upgrade Wizard of Windows 7, then check the manufacturer's website.

  My old Vista was not able to upgrade to Windows 7 (Toshiba).

  Upgrade Advisor advised me to some questions, and then I went to the Toshiba site and was informed any way uncertain "not compatible".

  If you want to switch from Vista to Windows 7 - check

  http://Windows.Microsoft.com/en-AU/Windows/downloads/Upgrade-Advisor

  Visit the site of the manufacturer for more information.

• I have a question regarding windows mail. I was send and receive mail with no problems until last Thursday. I can still receive mail, but I can not send.

  / * moved from answers Feedback * /.
   
  I have a question regarding windows mail. I was send and receive mail with no problems until last Thursday. I can still receive mail, but I can not send. My email is with bellsouth.net and comes in my computer through windows Messaging.  I spent an hour and a half on the phone with bellsouth, and they say that the problem is with my windows mail.  I tried to use a restore date, and that did not help either. I will post a copy of this message, as I keep getting.  Your server suddenly put an end to the connection. The possible causes for this include server problems, network problems, or a long period of inactivity. Object 't', counts: 'mail.bellsouth.net', server: 'mail.bellsouth.net', Protocol: SMTP, Port: 25, secure (SSL): no, error number: 0x800CCC0F thanks for any help.

  Sometimes, WinMail settings get screwed up and you must remove the account and then add it back back.  Make sure first that the antivirus software not interfere (see www.oehelp.com/OETips.aspx#3).   Delete your account completely, then close WinMail.  Then compact and repair the database of WinMail (see www.oehelp.com/WMUtil/).  Add your account to mail back once again, and then make sure you have the correct settings under Tools | Accounts | Mail | Properties | Servers and | Advanced to what AT & T Specifies to WinMail (or OE).  Then see if it works.

  Steve

• I am unable to get my separate chat windows when Movie to 2 different do people not sure what to do as new to this need help big ty time in adfvance

  I'm not sure if it's the web browser, I need to change or what I just need to get this model so good n still understood.

  Hello

  I suggest you post your question in the below link and check if it helps.
  http://answers.Yahoo.com/dir/index?link=list&SID=396546091

  Settings to separate all chat windows will be provided on the Web site or the instant messaging client which you are chatting and you must contact the respective assistance.

  Thank you