I received an error "no mapping between account names and security IDS was done" when I try to back up my files on a network drive. Help?

Similar Questions

• Error message "no mapping between account names and security IDS was done."

  I installed an external hard drive 1 TB USB to a desktop networked home.  I use this unit to save the desktop system.  I mapped it as a network drive for my wife's cell phone.  She has full network drive read/write permissions.  I'm trying to set up his laptop to backup over the network to the device using the backup utility provided with Windows Home Premium.  When I try to choose the local backup device on the network drive does not appear as an option.  When I try to configure the location using the networking option, I can select the device but then get the following error message... "No mapping between account names and security IDS was done."

  Hello BrkAwa,

  If the network drive does not appear when you try to backup, this means that the network drive is not mapped on your computer.

  Follow these steps to map the drive on your computer.

  1. click on the computer from your desktop or from the Start Menu shortcut. In the toolbar, you will find several buttons, including one called map network drive.

  2. click on it and the map network drive window opens. First, you must assign a drive letter for the connection, and then type the drive or folder that you want to connect.
  The folder may be located on a computer, or remote server that you access, FTP site, or a shared folder on your computer.

  3. If you want to connect to a remote computer only "-" followed by the name of the computer or IP address and then "------" track of the location of the folder that you want to connect.
  If you want to create a drive mapping to a folder on your own computer, type "\\127.0.0.1\" (this corresponds to the local host) or "\\computer_name\", then the path to that folder.
  Sometimes, when you create a drive mapping, you may need to use a special username and password that allows you to connect to it. In this case, click connect using a different user name .

  4. type the user name and password and click OK. Now, you will return to the previous window. Click Finish and the drive mapping will be created.

  5. If you go to the computer shortcut you will see again once a new disk with the letter that you have assigned is listed and you can access it at any time.

  Map the drive, then check if you are able to use the drive for backup.

  Thank you
  Irfan H, Engineer Support Microsoft Answers. Visit our Microsoft answers feedback Forum and let us know what you think.

• No mapping between account names and security IDS was done

  Hello

  I have a laptop of Acer under Vista Home Premium Service Pack 1.  I open advanced user accounts of & assistance, and I saw two names my old & news of the administrator. He used my name as the user name and my new name as the display name, so I deleted the old username & changed to match the full name (the new name).  After the change has been made, I get an error message "no mapping between account names and security IDS was done 26EE0668-A00A-44D7-9371-BEB064-C98683.  Now I can't access control panel to make changes to account. Help & Support in the start menu and Windows Explorer are no longer works. Tools on the toolbar doesn't work or the other.  I can't yet run a virus scan.  I did find something useful from my own research.  Help!

  Thank you
  Cheeszz
  P.S. I also started a McAfee Quick Clean to remove undesirable accumulation of the computer.  He cleaned the keys to an orphan registry, internet cache, temporary files & lost file fragments.  I don't know if he has also nothing to do with the error message.

  Hello Cheeszz,

  Thanks for posting your question on the Microsoft answers Forum.

  Essentially, you get the "no mapping between account names and security IDS was done" is because you now have an orphaned user account. This occurred when you deleted your old username which was still in use by the system under the name of each user name has a unique SID.

  I suggest that run you a system restore point, then you can go back to a previous point in time before you deleted the name of the user.
  Follow the article below for the establishment of a system restore procedure.

  936212 KB - how to repair the operating system and how to restore the configuration of the operating system to an earlier point in time in Windows Vista
  http://support.Microsoft.com/kb/936212

  You can also create a manual system restore point so that you can restore to that State in case of problems.
  Right-click on the computer icon in the desktop, then choose Properties
  In the left pane, click System Protection
  Alternatively, to directly access the System Protection tab, click Start and type SystemPropertiesProtection.exe.
  If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.
  Click the System Protection tab and then click on create.
  In the System Protection dialog box, type a description, and then click on create.

  If you do not have a restore point system, try to see if LastKnownGood configuration might work for you.
  Click on the URL link to get help setting up the last known good configuration:
  http://windowshelp.Microsoft.com/Windows/en-us/help/cdb4c0dd-5698-4197-B906-d6a6d413621d1033.mspx

  Please respond and let me know if these suggestions helped get your problem solved or if you still need help.

  Sincerely,

  Marilyn
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• When I try to use a MS fingerprint reader I get the message "no mapping between account names and security IDS was done."

  Original title: fingerprint digital mapping

  When I try to use a MS fingerprint reader I get the message "no mapping between account names and security IDS was done."

  I tried the fix (http://support.microsoft.com/kb/890737?wa=wsignin1.0) without success.

  Any ideas?

  Hello

  Have you tried to reinstall the fingerprint reader, as mentioned in the previous post article?

  If your computer is on a domain, the question you posted would be better suited for the IT Pro TechNet public. I would recommend posting your query in the TechNet Forums to get help:
  Windows XP IT Pro Forums
   
  For more information, see the articles:
  Understand and configure the Welcome screen and the classic logon screen
   

  Hope the helps of information.

  Let us know if you need help with Windows related issues. We will be happy to help you.

• No mapping between account names and security IDS made mistake by attempting to use the Task Scheduler

  I have noticed that my msfeedssync.exe were not working or updated so I went to the Task Scheduler to see what was going on and received the number above mapping between user names and security ID error I never use Task Scheduler, but I do not know its also used for RSS updates , I do all my own maintaince so I need only of GI RSS using a 3-year-old dimensions of dell with xp pro and its in tip top except for that shape it came only with a 80 GB hard drive and I've only used 20 concerts in 3 years that I use online for things important and backup storage I hope there is a solution for this because I installed ram to 4 GB and it has a 2.8 ghz Processor blazin fast and is in very good shape all help will be appreciated thanks

  Hello syncere99,

  1. What is the user account in the Task Scheduler are you for the work you are trying to use the Task Scheduler?

  The error code indicates that the user account that was used to create the job no longer exists. This could be because the user account is deleted. I suggest that you remove and re-create a job and check if you have the same problem.

  Thank you
  Irfan H, Engineer Support Microsoft Answers. Visit ourMicrosoft answers feedback Forum and let us know what you think.

• When I try to back up my files to an external hard drive I get error code 0 x 8000700020 how to stop what is happening

  Original title: Ox8000700020

  Hi, when I try to back up my files to an external hard drive I get error code 0 x 8000700020 how to stop what is happening

  Double post: http://answers.microsoft.com/en-us/windows/forum/windows_other-performance/ox8000700020/3c708968-5d37-40dc-97ef-2a44b72ca5fc

  I have merged the new post with the original question.

  -steve

• Catastrophic error when I try to back up my files

  When I try to back up my files, I cannot and I get a catastrophic error response. What, if any, are my options?

  Hello
  1. have you tried the suggestions posted earlier?
  This problem occurs because the backup process detects that the system drive is dirty.

  Windows Vista backup always includes the system as part of the backup drive. If the system drive is dirty, the backup process skips the system drive, and no snapshot of the system drive is created. Therefore, the backup cannot locate a snapshot of the system drive later, and the error occurs.
   
  To resolve this problem, run the disk check to fix the error on the system drive. To do this, follow the steps mentioned in the article below:
   
  Error message when you try to perform a backup system on a Windows Vista-based computer: "catastrophic failure (0x8000FFFF)".
  http://support.Microsoft.com/kb/973558

  Note: CHKDSK would attempt to recover bad sectors on the hard disk, in the course of this process there are chances of DATA loss from that particular area.
  Thank you, and in what concerns:

• Error: No mapping between account and the security of ID names was done when trying to setup of Dragon NaturallySpeaking 10.

  Original title: no mapping between account and the security of ID names was done.

  I am trying to set up my Dragon NaturallySpeaking 10 program. My computer (Dell Studio 1550 on Win 7 64 bit) has been recently reset and during the reinstallation of the DNS and the subsequent fine adjustment, I came across a page that wanted my username and admin password.. I plugged in and it came up with the error message: "no mapping between account and the security of ID names has been done." There is one account on my computer and my admin. account. If something has been lost in resetting? How can I fix / security ID card? Thank you for your help.

  Hi Hasky620,

  I recommend you contact the support of Dragon NaturallySpeaking for assistance:

  http://www.nuance.com/support/index.htm

• Receive an error message that Windows can not retrieve information about the disk when I try to put upgraded Windows XP to Windows 7.

  XP Home to Windows 7 upgrade Peoblems

  I can't update my laptop to windows 7, that he will enter the upgrade options, then it will say cannot retrieve information about this disk of computers. What should I do I deleted all leave them and still get this error. Thanks Chris

  It's a little late for this, but anytime you do an upgrade, you must be sure that your computer is compatible. My guess is your drive for windows 7 is a DVD and you have a CD or a witch of CD - RW drive can not read CD

  http://Windows.Microsoft.com/en-us/Windows/downloads/Upgrade-Advisor

• Task Scheduler error: "an error has occurred for task reminders - portable home. "Error message: the specified account name is not valid.

  HelloW everyone,

  I changed my name to the laptop and now every time I have lunch Planner task, I receive the following error message:

  "An error has occurred for task reminders - portable home. "Error message: the specified account name is not valid.

  I also have the problem with restore points, so these two issues relate to eachother? How can I solve the problem of the user name.

  Any suggestion and help appreciated

  Hello

  You can check out the link and check if it helps.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-performance/odd-Scheduler-error-messages/a487d70b-61c9-499F-ae15-ac903d6174eb

  Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following windows Help article.
  Back up the registry
  http://Windows.Microsoft.com/en-us/Windows7/back-up-the-registry

• When you install the 2007 Microsoft Office Suite Service Pack 2 (SP2), I still received the error code 646... I tried to download the RegCure as advised, but the problem still exists... Please help me with this problem... Thank you

  Ideas:

  • When you install the 2007 Microsoft Office Suite Service Pack 2 (SP2), I still received the error code 646... I tried to download the RegCure as advised, but the problem still exists... Please help me with this problem... Thank you

  I tried to download the RegCure as advised, but the problem still exists...

  Who advised you to 'download... '. RegCure? Doing so could only worse issues! If you ever think that your registry database must be cleaned, repaired, boosted or optimized (it isn't), read http://aumha.net/viewtopic.php?t=28099 and draw your own conclusions.

  See http://social.answers.microsoft.com/Forums/en-US/vistawu/thread/6e716883-7af4-4a9f-8665-2f4dd57eee8d ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• When you do a back up of files on a disk, receive error message 0 x 80070005

  When I try to back up files I get an error message 0 x 80070005

  Hello

  see if this information helps you

  make backups on an external hard drive or DVD

  How to make a backup of your data (all Vista versions)

  http://www.vista4beginners.com/how-to-backup-your-data

  How to restore your files

  http://www.vista4beginners.com/how-to-restore-files

  the 1st link below is how do the backup complete pc (Vista, full and professional company)

  http://www.bleepingcomputer.com/tutorials/tutorial145.html

  and that is how do to recover the backup complete pc

  http://www.bleepingcomputer.com/tutorials/tutorial144.html

  and here is the information of microsoft in restoring a system image backup

  http://Windows.Microsoft.com/en-us/Windows-Vista/restore-your-computer-from-a-system-image-backup

  If you have problems with the repost of process above in forum microsoft link that is specific to the backup below questions

  "This forum supports questions for the default backup utility in Windows Vista, Server 2008 and beyond."

  http://social.technet.Microsoft.com/forums/en-us/WindowsBackup/threads

• Difference between Oracle user and security

  Hi all
  
  Can someone give me the difference between--> Oracle--> user and security-> system oracle apps R12 resp. administrator user.
  
  
  Thank you
  Mahesh.
  
  Published by: 991854 on March 12, 2013 01:49

  Can someone give me the difference between--> Oracle--> user and security-> oracle apps R12 resp. system administrator user.

  Security > Oracle > register:

  Use this window to register a username with Oracle E-Business Suite ORACLE. An ORACLE user name grants privileges to access the ORACLE database
  http://docs.Oracle.com/CD/E18727_01/doc.121/e12893/T174296T174305.htm

  Security > Oracle > DataSet:

  A data group defines the mapping between the products Oracle E-Business Suite and ORACLE database ID. A data group determines which accounts of liability forms, concurrent programs and reports Oracle database to connect to. see: Definition of data groups, the Oracle eBusiness Suite system administrator Guide - Configuration.
  http://docs.Oracle.com/CD/E18727_01/doc.121/e12843/T156458T156461.htm

  Security > user > define:

  This window allows to set user Oracle E-Business Suite. This user is an authorized user of Oracle E-Business Suite and is identified by a user name.
  http://docs.Oracle.com/CD/E18727_01/doc.121/e12843/T156458T156461.htm

  Thank you
  Hussein

• When you access the virtual machine, getting the error "encountered an error when you try to use one of its virtual hard disks". Help?

  I received the "low disk space error" on a hard drive of the virtual machine dynamic expanding. I have increased my space of virtual hard disk using "My Computer" > manage > storage > "Disk management" and choose "Attach VHD" then resizing to max available (64 GB), and now I can not start the virtual machine. It gives the error: encountered an error when you try to use one of its virtual hard disks. Help?

  Hi NatalieFoster,

  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the TechNet Forums to get help:

  Windows 7 Virtual PC and XP Mode TechNet Forums

• Dreamweaver update don't forget the account names and passwords?

  This morning I did the update thing Adobe and it hung five applications, including Dreamweaver which I was working.

  I closed Dreamweaver and click [continue] and he finished. I am now running Dreamweaver 11, build 4916.

  I restarted Dreamweaver and made some changes to the page I was working on and has saved those and got an FTP error.

  Poking around a bit reveals that there is now no account name or password specified in my settings of the Site. And that's for ALL sites!

  Well, calm down... breaths of e e d p... We will re - import Sites using the old files .ste, right? They were created with the choice to save the account names and passwords, too. Point, click-click, the construction of the new site [2] and edit the page, save the changes and Boom! FTP error, once again.

  How can I fix it, please?

  Adobe aknowledges that question in the document of the basis of knowledge and skills associated with the update. I think that to solve it, you just need to restart your computer after the update to Dreamweaver.