ID of the LUN duplicate when you use several bays

Similar Questions

• How can I disable the mouse pad when you use a mouse plug-and-play?

  How can I disable the mouse pad when you use a mouse plug-and-play? I tried to disable the driver, and nothing works.

  Hello

  Check with support of the manufacturer system, documentation online or forums that there is probably
  Shortcut keys that enable and disable the touchpad functions.

  Parameters for TouchPad located in the control panel - mouse (there may be several tabs with TouchPad entered)
  and some come with a utility that loads in the Notification area next to the clock in the bottom right.

  ==========================================

  If necessary: (make sure that you have restarted at least once, if the above did not work)

  Panel of configuration manager devices - mouse and pointing devices - Double click on the touchpad - the driver tab-
  Click on update driver (it comes may not do anything like MS is far behind the drivers of certification), now right CLICK
  on the TouchPad and UNINSTALL.

  Then go to the USB and UNINSTALL ALL controllers except the category itself (all in). RESET

  This will refresh the driver for the TouchPad and battery USB. This does not prevent the touchpad from working.

  The similar procedure on XP, Windows 7 and Vista is the same, except that we need to clear the specific device if present.
  http://support.Microsoft.com/kb/310575

  Then go to the system manufacturer's website and get the latest touchpad drivers.

  Download - SAVE - go to where you put it-click on - RUN AS ADMIN.

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• Pages automatically reformats to the correct size when you use Folio Builder or what I have to do format pages iPad, for example, in the placed InDesign document in place from the beginning?

  Pages automatically reformats to the correct size when you use Folio Builder or what I have to do format pages iPad, for example, in the placed InDesign document in place from the beginning?

  Transferred to DPS forum.

  You must configure the pages of appropriately for the target device. For iPad, it is 1024 x 768.

• What are the supported items when you use multiple suites?

  Hi all

  I created a plugin that sends the current path to a url,

  his work very well with debugging in Visual studio 2005 and then it is added to the Adobe Illustrator work only once.

  Its transmission, the path is that for a single file. While I was trying for the second time its does not work

  I use more costumes in my plugin

  AIDocumentSuite

  AIFilePathSuite

  AIActionManagerSuite

  AIUnicodeStringSuite

  AIURLSuite

  I use the "'AIURLSuite ' to call the url and calls the url several times while its used only and its only works once with multiple suites. "

  What are the supported items when you use multiple suites? It is necessary to release all the variables and the suites after completing the task?

  Should they come out in the same order in which they are acquired?

  Thanks in advance

  Farida kaid

  As far as I know, there is nothing forcing you to unleash in the same or in front of the order in which you have acquired in. Frankly, in our plugin gain us once, then lock the plugin to prevent it from unloading and don't release suites when we finished. That said, as far as I know, you should be fine to learn/work/output several times.

• Problem with the format of the values in the command prompt (when you use multiple values)

  Hi all
  
  I have problem with the format of the values in the command prompt when you use multiple values.
  
  Value is year (2009) and when I use it in the drop-down list that is formatted, all right, as 2009, but when I use several values I get number as 2009,00. I put in year column format number with 0 decimal places and save by default in the year column. Year is formatted well anywhere in the query, such as 2009. Why is - what happens at the command prompt when you choose multiple values in prompt dashboard?
  
  Thank you

  I think the YEAR Data Type could be defined DOUBLE RPD.

  Use the CAST function in the formula (fx) and the output from test.

  CAST (INT YEAR)

  Hope, it will help you.

• Error message "an error the system cannot find the file specified" when you use Bitlocker

  Original title: Bitlocker to go not accessible by car usb

  Here's the short of it: I decided to use Bitlocker To Go on my USB drive, and while he was to encrypt the drive I plugged a USB DVD - RW drive (it

  s a netbook) and then I got an error message in the Bitlocker program that says "an error the system cannot find the file specified."  I closed the error message and open the Bitlocker Unlock program, put my password and press on unlock and now it only that sit there and spin and the light flashes on my Batman of Seagate HARD drive as it is accessed.  The internal data of the car do not make the same sound, as he did while he was being... just encryption sounds like there are in an infinite loop.  The disc is good and has no errors, and I scanned with SeaTools.  I have a lot of important data on this drive, and I really don't want to lose anything.  Help!

  Hello 5thgear,

  Thank you for the question!

  I'm sorry to know that have problems you with Bitlocker. I get it right you get an error message "an error the system cannot find the file specified" when you run the bitlocker encryption.

  I need to ask you a question to help you best.

  Were there any changes (hardware or software) to the computer before the show?

  Click on the link below.

  http://blogs.technet.com/b/ASKCORE/archive/2010/08/04/issues-resulting-in-BitLocker-recovery-mode-and-their-resolution.aspx

  Answer to us if you are having problems with bitlocker or any other issue of Windows, and I'd be happy to help you again and try to correct the problem as soon as possible.

  Good day!

  Hope this information helps.

• Applications using cmd + tab switching does not work (reverse return) when you use several spaces in the Sierra

  I usually have a lot of apps open it in full screen across a number of different areas.  In El Capitan, when I used cmd + tab to switch apps, it would just go directly to the application in the entire app was opened in.  Now, he tries to switch to the app, but then IMMEDIATELY switches to the space, in that I was already.  It's like if someone is sitting there playing this cruel on me joke where whenever I try to go to the app, it shows to me and then immediately sent me immediately.  Everyone knows something similar to this?

  To re-create the problem, have a few apps open it in full screen in different spaces, then try to switch to another application in another space using cmd + tab or try to switch to an application that is just open on the main office space.  It comes immediately rebascule on your original app!  I'm ready to tear my hair out!

  Feedback: Apple http://www.apple.com/feedback/

  With your same Apple ID, you can register for a free developer account and start a conversation with Apple engineers

  Bug Reporter https://bugreport.apple.com/

• I get the following message when you use Safari and Firefox. Works in Chrome: "we're sorry, the link that brought you to this page is not valid."

  I'm working with my bank account online and I get to the homepage very well. When I select the online banking, estatements, I get the following message when it tries to link to the electronic statement page.
  "We're sorry, the link that brought you to this page is not valid." Chrome has no problem displaying this page, but Firefox and Safari gives me the same message.

  Note that I posted this already above, but don't not checked if she was tried.

  You may need to allow cookies from third party (visited or all).
  
  
  To view the history settings and cookies, choose:

  • Firefox > Preferences > privacy > Firefox will be: "use the custom settings for history".

• FTP creates and deletes the temporary instead of the download file when you use the switch S:

  We use Windows 2008. There is a strange problem to start the FTP., receive a file.
  I can receive the file when the command line GET command. When I use the file with the command (ftp - s:Filewithcommands.txt), ftp creates a temporary file and remove it automatically without doing the real download.
  Thanks in advance

  Hello

  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the TechNet Forums:

  http://social.technet.Microsoft.com/forums/en/winserverDS/threads

• error message saying that it is the wrong key when you use a sticker

  Product key

  I have an OEM version of vista Home premium. I'm trying to load on an acer extensa 5420 using the product key on the bottom of the laptop. When I enter the key, I get an error message saying: it's the wrong key. How can I use this disc to reinstall windows?

  Hello

  The OEM recovery disks are the brand and the specific model

  You can't use a disc from another manufacturer

  How to reinstall Vista

  Contact the manufacturer of the laptop computer and ask them to send you to vista recovery disks to reinstall the operating system back as it was when you bought it

  they do it for a nominal cost of $

  also ask them if you have a recovery partition on your hard drive to get back to the way you bought

  you would normally press F8, F9, F10 or F11 or Alt + F10 or 0 to start to start the recovery process according to the manufacturer

  Ask them of the exact key sequence

  or borrow a vista microsoft dvd; not a HP, Acer recovery disk etc

  Make sure that you borrow the correct 32-bit or 64-bit microsoft dvd to your computer

  they contain all versions of vista

  This is the product key that determines which version of vista is installed

  http://www.theeldergeek.com/Vista/vista_clean_installation.html

  How to replace Microsoft software or hardware, order service packs and replace product manuals

  http://support.Microsoft.com/kb/326246

• Have the intermittent connection when you use WiFi and conflict error IP address when using Ethernet

  I have intermittent problems with my wireless internet connection. I contacted the ISP and they analyzed the configuration of the modem-router, changed some and told me to try to reconnect. I try again and the connection is OK. The ISP has caress each other on the back and sent me on my merry way not-so-small. Problem is at an unpredictable time, problems (do) happen.

  Usually the failure scenario does not have a huge problem - plus one
  gene as a problem. I just keep trying to connect through Windows
  Network and sharing Center, and possibly the connection is made. But in some cases, time is critical; I eventually lose 10 to 20 minutes of typing-search-typing-correction-etc in a web form when the connection disappears before making a SHIPMENT. (Some time, after the failed wireless and re - connect, I was actually able to recover pretty quickly that the site has not been exceeded me.) So in this scenario I can't lost any strike.)

  I would like to connect my pc to the internet via an ethernet cable
  the modem-router. I could take this approach right after the wireless
  connection failed. Or in a preventive way, when I know I'll be typing-
  mode of research-type-fixed-etc and I want to be really sure. When I tried this, I get the error "Windows has detected an IP address conflict.

  What I do at this point to get around the Wi - Fi connection and connect through the Ethernet cable?

  The topic is edited for clarity of the moderator.* *.

  [Original title: LOST INTERMITTENT WIRELESS INTERNET CONNECTION]

  It is not clear what parameters your ISP technology management may have changed on your modem/router.  As a general rule, the ISP concerned the link between their server and your modem, but any fiddling with settings that control this link will not effect either on the link between your computer and the modem/router.

  If you still haven't reset your router to its default settings, do not unless you know the necessary internal router settings for you connect to your ISP.  If you have a cable Internet connection, the default settings may work OK, but if you have a DSL, they probably won't.

  You should not get this "IP address conflict" error when you connect the Ethernet cable.  Follow these steps:

  Open the "network and sharing Center" and then click on "change adapter settings".  You should see an icon for your wireless network adapter and an icon for your 'connection to the Local network' (your Ethernet connection).

  • Right click on each of the icons, and select 'properties '.
  • There should be a list titled "this connection uses the following items."  In this list, select "Internet Protocol Version 4 (TCP/IP)" and then click "Properties".
  • The radio buttons to "Obtain an IP address automatically" and "Obtain DNS server address automatically" should both selected.  If this is NOT the case, do so and OK your way out.  Furthermore, cancel your way.

  If a card has been configured to use a specific IP address, your "IP address conflict" should now be fixed (you may need to restart the computer for the change to take effect).

  If cards were already configured to obtain its IP address automatically, the problem lies in the configuration of your router.  You will need to access the router's Web utility to study and make changes.  To help you provide the brand and model of the router of the label on the back or the bottom.  Also do the following to a time where you have an Internet connection:

  Open a command prompt window (type cmd in the search box and press enter)

  1. In the black command prompt window, type the following command, and press ENTER after each line

  ipconfig/all > "% userprofile%\Desktop\ipinfo.txt".

  Notepad '% userprofile%\Desktop\ipinfo.txt '.

  output

  1. In the opened Notepad window, click Edit > select all (or press CTRL + A) and then click Edit > copy (or press Ctrl + C)
  2. In the body of your Question, right-click > paste (or press CTRL + V) the data of the Notepad window
  3. Close Notepad and remove ipinfo.txt from your desktop

• Keep the text perpendicular to the base line when you use the string.

  Is there a way to keep the text perpendicular to the base line when using the warp function?  I'm trying to reproduce a decal with curved text.  When I use the string to get the text that is curved like the original, the letters are slightly tilted.

  You could try to make each letter on a separate text layer, then use Image > transform > free transform to adapt the letters in place.

  A lot more control over the placement of the letter and size that warp text offers.

  

• How to avoid changes to the NEF file when you use Camera Raw?

  He does not have to happen, but now, when I edit a NAVE in Camera RAW file, then save it as jpg in PS6 file NAVE is also changed, so I can't undo my changes here.  How to stop this change to the NEF file?

  And if you use the bridge to eliminate all changes in the NEF file you made in ACR and return to its state choose Edition > develop settings > clear settings. (You'll notice that the marker of this image in Bridge has been removed, confirming the fact that the NAVE is back to change.)

  

• Retrieves the CLOB data when you use the keyword DISTINCT to the other columns

  I have a question about how to recover the CLOB data.
  
  The requirement is something that there are about 20 + columns I need to recover around 5 tables joined in the select statement.
  Since the result set after that join will also duplicate values, I need to use the distinct keyword to filter the result set.
  But there is in the columns of 20 + 2 columns to CLOB data I need to recover.
  
  Whenever I have use SEPARATE, I'm ORA-00932: inconsistent data types: expected - received the CLOB error.
  
  I know that this DISTINCT keyword cannot be used for CLOB data types.
  
  So can anyone here help me with any work around / another way to get the CLOB value in the QUERY SELECT.
  
  So please help me out in the present.

  Hello
  This forum is for problems using SQL * Developer. If the problem only occurs if you are using SQL * Developer then please give us the SQL code that you are running.
  If it happens in SQLPLUS then, it would be preferable to raise it in the SQL Forum-

  Forum: SQL and PL/SQL

  SQL and PL/SQL

  This forum is for problems using SQL * Developer.

  Kind regards
  Mike

• How to install the PFB fonts when you use Windows 7 64-bit?

  I got a new computer with Windows 7 64 bit. But when I copied the fonts I used on the old computer, PFB fonts do not work any longer.

  The former ATMF program doesn't work so how can I now install PFB fonts on this computer?

  Anni

  I hope that you did not try to install the old software of Adobe Type Manager . If you did, you may need to completely reload Windows if you cannot restore your system to its state before you try to install this software!

  Assuming that you did not this fatal error, the method to install Type 1 fonts, which each consists of a .pfb and .pfm file is as follows:

  (1) copy the .pfb and .pfm files in a single directory if they are not already available.

  (2) select the .pfm for the fonts you want to install files.

  (3) right click and select install which will then install the fonts on your system by copying the .pfb and .pfm files into C:\Windows\Fonts directory. Do not drag - move these files! If you do not want the font files themselves reside in the C:\Windows\Fonts directory, when you right click on the file, select install as a shortcut. This installs the police but he refers to his current location.

  -Dov