IDSM2 in inline mode

Similar Questions

• IPS Inline Mode span configuration

  In Inline Mode IPS V5, the second interface (where a package goes out) a paired interface must be configured as a span port or a regular port? Where can I find more information about it? Thank you.

  Need more information about your configuration set. Generally speaking, the answer is "regular shipping". Your use of "span" leads me to believe that you are being implemented in a switch. In this case, be advised that if you try to loop in the same switch that you originally, you will need to have this second port in a vlan different. The sensor does not spread, it is a "virtual" thread

• Development of probe pair interface inline mode

  I've never set up a probe pair interface inline mode, and I had a few questions about this

  It is my understanding that traffic from a virtual local network would be passed to the other through the probe (and then you implement your strategies passed).

  But then, how would you set up the SPAN or capture ACLs on the side of switching? A session of the monitor will put a port in disabled mode (even though I think you can use the session monitor x destination penetration to allow traffic of it).

  Or you want to use the

  Capture switchport

  order with FSPAN on both interfaces?

  Any advice would be great

  Hello

  For inline-pair configuration should be something like this

  Assuming that 1/1 and 1/2 switchport. Port Gig0/0 and 0/1 Gig IPS

  1/1 and Gig0/0 must be in one vlan, say 800.

  1/2 and Gig0/1 should be another vlan, say 810.

  switchport config:

  1/1

  switchport

  switchport access vlan 800

  switchport mode access

  1/2

  switchport

  switchport access vlan 810

  switchport mode access

  All traffic vlan 800 is sent to the port in vlan 810 and vice versa after inspection.

  Kind regards

  Sawan Gupta

• IPS Inline Mode Interface - you can use a port channel?

  Hello

  I am trying to determine if you have a 2-gig Layer 3 Port channel through a 4260 IPS appliance. See the attached diagram. Is this possible?

  The customer, I work with would prefer not to enter this cost equal to Port-Channel 1 gig of links (I don't think that there is a difference in performance...) However, I think that if they want the device inline, as the diagram shows - they will have to break the port-channel. Is this a correct assumption?

  Thank you

  Brad

  Asymmetric traffic will prevent the sensor works best, he is capable. There is a configuration that can be done to allow the detector deployed in an asymmetrical environment, BUT it can affect the ability of the sensor to detect attacks, allows through evasions which would have been prevented and will not affect general performance of the sensor.

  If running in unbalanced mode should be avoided if possible. BT in cases where it cannot then the sensor always allows with degraded functionality.

  Traffic spikes above what the sensor can manipulate at will cause ignored packets. There is no help for too much traffic.

  The relief you talk I guess is the bypass function. The bypass feature does not affect during the subscription of the sensor. The bypass feature will only kick if the analytical engine crashes due to a bug.

• IDSM2 on the inline 6500 IOS mode support?

  Hello

  I have a JOINT-2 running IPS5.1 (1 d) (recently updated to 4.x) software that sits on a 6500 IOS.

  The IPS Device Manager shows gi0/7 and gi0/8 as well in Promiscuous mode. There is no option to change the inline mode and pair them up.

  Is it so that JOINT-2 currently supports only Promiscuous mode?

  If so, this module is always as IDS despite the execution of IPS5.1. Is it not? What is the advantage that I get after upgrade from 4.x to 5.1?

  -Vasanth

  There are 2 pieces of the puzzle.

  There is the JOINT-2 version and it takes in charge, but also the native IOS of Cat 6 K version and that it supports.

  Supports the v5.1 (1 d) JOINT-2

  (a) promiscuous mode.

  (b) mode InLine Interface pair (2 interfaces are matched to online tracking) and also

  (c) pair online mode of Vlan (2 VLANS on a single interface is matched for online tracking, you will also see it called inline-on-a-stick)

  But for these features to be used, the code switch must also support the configuration on the side of the switch of the JOINT-2 for each of these 3 features.

  Native versions of IOS prior to 12.2 (18) SXE will only support the Promiscuous on JOINT-2 mode.

  12.2 (18) SXE and later versions support Interface InLine mode on JOINT-2 pair.

  No native IOS version does currently support InLine Vlan pair on JOINT-2 mode (a new versions native IOS with this support is currently in development).

  For inlining (IPS), you need to run a Native IOS version 12.2 (18) SXE and later and on the JOINT-2 run IPS versions 5.1 (or even older 5.0).

  (NOTE: Cat OS 8.5 (1) takes in charge the 3 modes of JOINT-2.) Therefore, if you use cat instead of the native IOS OS, then run version 8.5 (1) to have access to all the features of IPS 5.1 (1) on the JOINT-2)

  If you run a Native IOS version prior to 12.2 (18) SXE and the JOINT-2 then it can run in "Promiscuous" mode even if 5.1 (1) is responsible for the JOINT-2.

  However, even in "Promiscuous" mode the IPS 5.1 (1) software has a few advantages.

  There are several engines and engine parameters are only supported in version 5.1 and not the version 4.0. (So there are several signatures that are either one) not yet created for sensors 4.x, or b) signature 4.x is not as precise as the signature of 5.x in new engines.

  (These new engines are proved invaluable in writing signatures to detect some of the new attacks that came out last year).

  There are of course other benefits:

  For example:

  (1) risk of note to best aid priority to alerts.

  (2) fitlering more flexible mechanism for alerts that allows individual actions of fitlering

  The 2 features above are only 2 of the new features that have been added in 5.0 and 5.1 that apply both of promiscuity and online modes.

• Impossible mode Inline on AIP - SSM

  I try to get my SSM module is running in inline with an ASA5520 mode. In a political configuration service inline mode is selected, however on the IPS says background basket interface Promisicuous.

  Am I missing something obvious?

  Edit:

  The lines of configuration specific all look ok:

  outside-class class-map

  match any

  outside-policy policy-map

  IPS description

  Outdoor category

  IPS inline help

  You encounter a bug in the IDM.

  IDM is incorrectly assuming that the interface is in Promiscuous and promiscuity.

  The sensor itself is considered just an interface monitored rather than online or promiscuity. Each package will have a header attached by the ASA that determines whether or not the packet should be monitored inline or promiscuity.

  This is fixed in IDM then she calls it just a substantive interface basket instead of incorrectly assume that it's an interface of promiscuity.

• Mode Inline JOINT-2

  Hello

  I work with the JOINT-2, we have Cisco 6509 with CSM and FWSM, we plan JOINT-2 in Inline mode and now I want to track the traffic that arrives through Interface from outside the context of FW (which is nothing but a VLAN A, B VLAN, Vlan C. on MSFC)

  Data flow: JOINT - ISP RTR - internal RTR - FWSM - MSFC CSM.

  JOINT version is 5.1 (4) S257.0,.

  It will support only two VLANS (IN and OUT) on the access mode.

  My problem is that I don't know how to analyze the traffic of 3 numbers of VLANS (A, B, C).

  Cisco 6509 - Version 12.2 (18) SXF7,.

  You can use the mode to pair for the VLAN inline to monitor traffic entering on VLAN specific. For example

  You have VLAN 100 200 and 300 on MSFC that you want to watch inline.

  You must configure the VLAN 101 201 and 301 (L2 only) and send the VLAN 100-101 200-201 300-301 to JOINT-2.

  You then create pairs VLAN on JOINT-2 module as below

  1 pair of VLAN 100-101-1

  2 pair of VLAN 200-201-2

  3 - VLAN 300-301 - pair 3

  Then set over three pairs of virtual sensor and will monitor this traffic for online operation.

  Inline VLAN pair mode is based on VLANs, so it doesn't really matter if them VLANS are behind or front of the FWSM.

  See you soon,.

  Vinod

• SIT: Settings of Inline of Matlab: Simulation Environment & remote target

  Hi all

  When I inline in a Simulink model parameters, and when I run it in the SIT Simulation environment, it's as if they would not have been treated in inline mode. Each block of the model appears.

  And when I try to launch it on a remote target (PXI-RT controller), the blocks that interest me are present, the constants that I put in the workspace are disappearing.

  Any suggestion, please? : PEI

  Thank you

  Hugues

  
  

• Difference between line and liabilities of ips mode

  Hi I'm new to ips. I got a 4215 sensor ips who says she can define control interfaces it is in passive mode, in which it can read packets directed to it by a switch. now since it is an ips when he reads a packet that triggers an alarm and action game goes to zero it will require a pix or a router to block traffic from the attcker or it may hang on its own since it a FPS. I'm not sure about that. can u pls guide me on this. At latest

  concerning

  Assane

  Hi... the main difference is that Supreme or passive mode provides reactive protection. It can be configured to reset the connection to the attacker, IP blocking, and registration of intellectual property, but it cannot stop the initial attack on the objectives. The reason is that packets which he controls have been copied and transmitted by sessions SPAN or promiscuosly listening to traffic on a segment.

  When the sensor is on inline mode, traffic must pass through the interfaces of the probe (pair). Traffic is inspected, tested against the signatures and then if OK, then transmitted to the destination. This approach offers preventive protection because the sensor can stop an attack BEFORE it reaches the target which is something that IDS (passive sensors) can not do

  In summary, I suggest you try to use your sensor in inline mode... It offers not only the same perfect for ID but additional protection against attacks.

  I hope that helps... Please note this!

• (ASA) AIP - SSM 10 Inline; Supreme events?

  A 5520 ASA with SSM-10 GOAL is set to inline mode, but the events of the show for 2 hours (sensor > HS event past 02:00) of the Interior of the sensor shows and "promicuous mode", "left promicuous mode'."

  This AIP SSM - 10 has only one gig0/0 and gig0/1 where o/o is taken out of service and a value default virtual sensor (vs0) is assigned to gig0/1. I see the statistics (sensor > sh SEO-engine of analysis) to gig0/1 so I collect statistics.

  If the configuration of the ASA 5520 has the following policy of inline and events log shows that enter and exit in promiscuous mode so how do I check if I am inspection/recovery in inline mode?

  (ASA > sh run access-list IPS)

  IPS list extended access permitted ip DMZ 255.255.255.0 26.26.1.0 255.255.255.0

  (ASA > sh run | b class-map)

  class-map IPS

  corresponds to the IP access list

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the netbios

  inspect the rsh

  inspect the rtsp

  inspect the skinny

  inspect esmtp

  inspect sqlnet

  inspect sunrpc

  inspect the tftp

  inspect the sip

  inspect xdmcp

  inspect the waas

  inspect the icmp

  class IPS

  IPS inline help

  !

  global service-policy global_policy

  (sensor > sh interfaces)

  ...

  Statistics interface GigabitEthernet0/1 MAC

  Function of interface = interface detection

  Description =

  Support type = backplane

  By default Vlan = 0

  Inline = unpaired mode

  Pair of status = n/a

  Circumvention of Capable hardware = no.

  Twin derivation material = n/a

  Link status = upwards

  Link speed = Auto_1000

  Link Duplex = Auto_Full

  Lack of Packet percentage = 0

  Total packets received = 95044

  Total number of bytes received = 8715230

  Total multicast packets received = 0

  Total of broadcast packets received = 0

  Total fat packets received = 0

  Total sousdimensionnés packets received = 0

  Receive the total errors = 0

  Receive FIFO overruns total = 0

  Total packets transmitted = 95044

  Total number of bytes sent = 9047702

  Total multicast packets sent = 0

  Total broadcast packets sent = 0

  Total fat transmitted packets = 0

  Total packets transmitted sousdimensionnés = 0

  Total transmit errors = 0

  Total transmit FIFO overruns = 0

  sensor > sh events last 02:00

  evStatus: eventId = 1203360411830836145 = Cisco vendor

  Author:

  login host: ASA2_IPS

  appName: kernel

  appInstanceId:

  time: 2008-02-20 19:01:46 2008/02/20 19:01:46 UTC

  syslogMessage:

  Description: device ge0_1 entered promiscuous mode

  evStatus: eventId = 1203360411830836146 = Cisco vendor

  Author:

  login host: ASA2_IPS

  appName: kernel

  appInstanceId:

  time: 2008-02-20 19:01:53 2008/02/20 19:01:53 UTC

  syslogMessage:

  Description: the promiscuous mode device ge0_1 left

  The left State events and entered promiscuous mode are usually generated when you do a 'package of display' or 'the capture of packets' command on the CLI of the sensor.

  Track order of the package is promiscuity but is independent of promiscuity or inline followed by analysis of the probe engine.

  If you have inline monitoring using the probe analysis engine.

  And still make command package to the cli for your own monitoring promiscuity of those same packets. Here are 2 independent monitors of the same packages.

  If I remember right inline monitored packets always get returned to the ASA (unless expressly denied), which is not promiscuous packets. So check sensors gig0/1 interface statistics and the number of packets for transmission. If receive and transmit accounts are quite close, then packets are monitored by the analytical engine InLine. If the number of transmission is nil or very low then the packets are likely promiscuous monitored.

  With the configuration of your ASA you are correctly configured for online tracking.

  So I don't think that you are investigating inline, and status messages are specific to your start and stop of the command 'package' on the CLI for your own independent viewing packages promiscuity.

• JOINT-2 flow in Bypass Mode?

  HI, I have documentation cisco joint-2 a 500Mbps flow in inline mode and the throughput of 600Mbps in passive.so guess our ihsane-2's in inline mode, then if we put our joint-2 in Bypass mode, how traffic joint-2 can handle without any inspection? (flow)?

  Thank you.

  The JOINT-2 would be only supported to the same 500Mbps for inspection and by-pass.

  There is not a separate ByPass mode ranking.

  Having said that, the JOINT-2 will be much higher than 500Mbps in ByPass mode (assuming that nothing else on the sensor).

  But I don't know how much of more since don't usually test us the performance in ByPass mode.

  You wouldn't want to plan your network on the performance of ByPass capacity.

  The other reason is that when the sensor bypass there will be something else in the sensor.

  In the case of an update of the Signature, there will be a treatment of signing consuming much of the CPU and memory for ByPass will not perform to its peak performance.

• IPS inline & port interface port trunk Switch

  Hello

  Is it possible to configure the IP addresses as the topology below? SW1 and SW2 SPI connection ports is in trunk mode. I would like to configure the IPS in inline mode pairing interface. (not the vlan pairing mode)

  SW1 - IPS - SW2

  Kind regards.

  Yes, this method is fully supported.

  If you want to control all the VLANS with a single virtual sensor, then assign the pair inline interface to the virtual sensor.

  If you want to monitor the VLANS with different virtual sensors, we support groups vlan on this pair of inline interface.

  Do not confuse "inline-pair of vlan" with the "groups of vlan inline on a pair of inline interface.

  The "pair of vlan inline" will pair 2 VLANS on the same interface. When a package arrives in the sensor it will be sent back the same interface with its header vlan has changed.

  The "groups of vlan" on a pair of inline interface don't change headers for VLANs.

  They are only used for virtual local networks, so that the Group of VLAN can then be assigned to a specific virtual sensor.

  You could then take a group of VLANs for your office network employees and assign them to vs0 and take a second group of VLAN for your DMZ and assign them to vs1.

  You can place a vlan unique within each vlan, or you can place several VLANs within each group vlan.

  But it only made sense to have 4 groups of vlan, because you have only 4 virtual sensors on most devices (a bit like the 4215 have 1 virutal sensor so you can make groups of vlan on the 4215).

  I also recommend that you change your virtual sensor and set the Inline TCP Session tracking mode on "Interface and Vlan. In this way the sensor will separately monitor connections on each vlan. This is necessary if a router can route traffic between several VLANs. Without this setting, the sensor will become confused if it sees the same connection of multiple VLANs.

• Cisco IPS inline or promiscuity

  Hello

  Is there a way or the command to type so that she can tell u that this IPS is inline or promiscuity?

  in a Word how to check how my IPS is running?

  Thank you

  Its simple... you need two interfaces for inline mode...

  in cli device sh short interfaces clearly will tell u if interfaces has been matched or not and also the interfaces sattus.

  If you use idm/csm, you can find it easily by seeing the intrface Summary tab

• Load balancing mode

  NSX LB operate in one of the 2 Modes: an arm and Inline Mode.

  But in NSX ICM course lab workbook is another mentioned mode: 2 in armed mode. Also in this transparent mode check box is not selected.

  What is this mode of arm 2.

  NSX Edge has no concept of 2 arms or deployment 1 arm.

  The NSX know Edge is in the pool:

  . Transparent enabled-online SNAT is configured

  . Transparencies with disabilities-online SNAT is not configured

  For example, when you deploy an edge in arm mode 2:

  "Customer - edge - servers_load_balanced" (with servers by default gw = border)

  If you have active Transparent, it will works and the server will see the real client IP address @, so that the server will respond to Client IP @ (via the default gw = border)

  If you have disabled transparent, it works and the server will see the IP edge @, so that the server will respond to the IP edge @ (which will be NAT to answer the customer)

• Prepares the query via the Inline view

  Pls help to prepare a query i can extract the following data through view inline (IE, except using the UNION):
  
  1. the SELLER who works in deptno # 30
  2. the MANAGER working in deptno # 20
  
  Department # 30 both SELLER and MANAGER work same Department # 20 both SELLER and MANAGER work.
  
  I want to go get sole MANAGER of Department # 20 and only the SELLER in Department 30.
  
  
  I can retrieve the desired data above by 'UNION' but I don't know if the above data can be searched other than 'The UNION' as INLINE mode.
  

  INSERT INTO EMP
  VALUES
  (7369,'SMITH','CLERK',7902,'WEDNESDAY, DECEMBER 17, 1980',800,NULL,20)
  /
  INSERT INTO EMP
  VALUES
  (7499,'ALLEN','SALESMAN',7698,'FRIDAY, FEBRUARY 20, 1981',1600,300,30)
  /
  INSERT INTO EMP
  VALUES
  (7521,'WARD','SALESMAN',7698,'SUNDAY, FEBRUARY 22, 1981',1250,500,30)
  /
  INSERT INTO EMP
  VALUES
  (7566,'JONES','MANAGER',7839,'THURSDAY, APRIL 02, 1981',2975,NULL,20)
  /
  INSERT INTO EMP
  VALUES
  (7654,'MARTIN','SALESMAN',7698,'MONDAY, SEPTEMBER 28, 1981',1250,1400,30)
  /
  INSERT INTO EMP
  VALUES
  (7698,'BLAKE','MANAGER',7839,'FRIDAY, MAY 01, 1981',2850,NULL,30)
  /
  INSERT INTO EMP
  VALUES
  (7782,'CLARK','MANAGER',7839,'TUESDAY, JUNE 09, 1981',2450,NULL,10)
  /
  INSERT INTO EMP
  VALUES
  (7788,'SCOTT','ANALYST',7566,'SUNDAY, APRIL 19, 1987',3000,NULL,20)
  /
  INSERT INTO EMP
  VALUES
  (7839,'KING','PRESIDENT',NULL,'TUESDAY, NOVEMBER 17, 1981',5000,NULL,10)
  /
  INSERT INTO EMP
  VALUES
  (7844,'TURNER','SALESMAN',7698,'TUESDAY, SEPTEMBER 08, 1981',1500,0,30)
  /
  INSERT INTO EMP
  VALUES
  (7876,'ADAMS','CLERK',7788,'SATURDAY, MAY 23, 1987',1100,NULL,20)
  /
  INSERT INTO EMP
  VALUES
  (7900,'JAMES','CLERK',7698,'THURSDAY, DECEMBER 03, 1981',950,NULL,30)
  /
  INSERT INTO EMP
  VALUES
  (7902,'FORD','ANALYST',7566,'THURSDAY, DECEMBER 03, 1981',3000,NULL,20)
  /
  INSERT INTO EMP
  VALUES
  (7934,'MILLER','CLERK',7782,'SATURDAY, JANUARY 23, 1982',1300,NULL,10)
  /
  INSERT INTO EMP
  VALUES
  (100,'SALAM','SALESMAN',7698,'FRIDAY, FEBRUARY 20, 1981',1600,300,20)
  /
  INSERT INTO EMP
  VALUES
  (101,'KARIN','SALESMAN',7698,'SATURDAY, FEBRUARY 21, 1981',1250,500,20)
  /
  INSERT INTO EMP
  VALUES
  (102,'RAFIQ','SALESMAN',7698,'SATURDAY, FEBRUARY 20, 1988',1250,1400,20)
  /
  INSERT INTO EMP
  VALUES
  (103,'JABBAR','SALESMAN',7698,'WEDNESDAY, FEBRUARY 20, 1980',1500,0,20)
  /
  INSERT INTO EMP
  VALUES
  (500,'RAHIM','MANAGER',7839,'THURSDAY, DECEMBER 16, 1971',2975,NULL,20)
  /

  Thank you.
  
  Sharif
  
  Published by: user13094274 on May 8, 2010 06:49

  Am I wrong?