IKE_PLATFORM_VERSION_MISMATCH Mac VPN client
I am trying to connect to my corporate network through the VPN to my Mac. Hardware VPN is a Version of Cisco VPN 3000 4.7.2.P hub. I can connect successfully using Cisco VPN Client for Windows 5.x. However, I am unable to connect by using Cisco VPN Client 4.9 for Mac OS X. The error I get is;
Marking of IKE SA delete (I_Cookie = EF82F027BACBF0CD R_Cookie = 7298F26225E0C33C) reason = PEER_DELETE-IKE_PLATFORM_VERSION_MISMATCH
The error message "PEER_DELETE-IKE_PLATFORM_VERSION_MISMATCH" seems to suggest that the VPN concentrator is configured to run the VPN Client version/specific operating system and this particular version does not appear in the configuration.
The Concentrator VPN, please visit the following:
Configuration | User Management | Groups |
Then select the group that you connect with and click 'change '. Go to the IPSec tab and at the bottom of the page, you will find the option that says "limit Client Version & Type". Please check if 4.9 for Mac OS X is listed.
If it is empty, you can see the BASIC GROUP, and the group to which you are connecting can inherit the settings of the BASIC GROUP.
Hope that solves this problem.
Tags: Cisco Security
Similar Questions
-
Need help with native VPN client for Mac to the Configuration of the VPN router RV082
Guys,
I am trying to set up router RV082 VPN Client with native Mac for my remote access. However, no matter what I did, I'm not able to make works. Can any give me an example of how to set my router RV082 and Mac Book Pro (Mountain Lion)?
Thank you
Hi Jixian, the native client MAC does not work. The IPSEC VPN client is the same as the 5.x Cisco VPN client is not supported on this device.
Your alternatives are to use PPTP or a 3rd party IPsec client such as ipsecuritas.
-Tom
Please evaluate the useful messages -
I could not connect using Mac OSX VPN Client 4.9. The "DEL_REASON_PEER_NOT_RESPONDING" message continues to appear. The log is attached.
Think you that requests connection to the VPN server. Newspapers, looks IKE packets never make to the customer. Could be a firewall on the client that blocks the IKE/IPSEC traffic or Server VPN itself does not. If he's the only successor client, check for the personal firewall or a firewall device blocking traffic.
Kind regards
Arul
* Rate pls if it helps *.
-
The ID attribute of the station call needs for Anyconnect VPN client MAC address
Hi all
We test tring Anyconnect VPN users to connect using the certificate. ASA East of validation / authentication user based on cert and approval it requires Radius server (ISE). Currently ASA sends the Ip address of the VPN client in «calling station ID» We want ASA to send the Anyconnect VPN client MAC address to the radius server in RADIUS attribute «calling station ID» Is it possible to do this. Get around them?
Parag salvation,
The calling Station ID always contains the IP if Anyconnect VPN.
L3 is originally unlike wireless which has L2 Assoc.
Currently no work around.
Respect of
Ed
-
Problems to connect via the Cisco VPN client IPSec of for RV180W small business router
Hello
I tried to configure my router Cisco of RV180W as a customer VPN IPSec, but have encountered a problem that I hope someone can help me with. "" I managed to do the work of configuration so that the Cisco's VPN IPSec client authenticates successfully with the XAUTH user, I put on the router, but during the negotiation, the client ends with the following, which appears several times on the router error message: ' Mar 20 Oct 19:41:53 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for
> [34360] has no config mode. I've read around the internet and a number of people seem to say that the Cisco VPN Client is not compatible with the router, but the same thing happens to my iPhone VPN client.
Is it possible that this can be implemented? Below, I have attached the full configuration files and the log files. Thank you much in advance.
Router log file (I changed the IP
addresses > respectively as well as references to MAC addresses) Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: floating ports NAT - T with counterpart
> [44074]
Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] WARNING: notification to ignore INITIAL-CONTACT> [44074] because it is admitted only after the phase 1.
Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for> [4500]
Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for> [44074]
Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received unknown Vendor ID
Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received Vendor ID: CISCO-UNITY
Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT detected: is located behind a device. NAT and alsoPeer is behind a NAT device
Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: request sending Xauth for> [44074]
Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association established for> [4500] - > [44074] with spi = >.
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REPLY' of> [44074]
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: login successful for the user "myusername".
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser connected from the IP>
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: sending of information Exchange: Notify payload [10381]
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REQUEST' of> [44074]
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no config mode
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no config mode
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no config mode
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no config mode
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: ignored attribute 5
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no config mode
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no config mode
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no config mode
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no config mode
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no config mode
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no config mode
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28683
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no mode config
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28684
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no config mode
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no mode config
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: remove the invalid payload with doi:0.
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: purged-Association of ISAKMP security with proto_id = ISAKMP and spi =>.
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser Logged Out of the IP>
Mar 20 Oct 20:03:16 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association deleted for> [4500] - > [44074] with spi = > The router configuration
IKE policy
VPN strategy
Client configuration
Hôte : < router="" ip=""> >
Authentication group name: remote.com
Password authentication of the Group: mysecretpassword
Transport: Enable Transparent Tunneling; IPSec over UDP (NAT/PAT)
Username: myusername
Password: mypassword
Please contact Cisco.
Correct, the RV180 is not compatible with the Cisco VPN Client. The Iphone uses the Cisco VPN Client.
You can use the PPTP on the RV180 server to connect a PPTP Client.
In addition, it RV180 will allow an IPsec connection to third-party customers 3. Greenbow and Shrew Soft are 2 commonly used clients.
-
What VPN Client for ASA 5550 AnyConnect Premium connection?
We have version9 a couple of ASA550 I want to put in place a VPN client for use with remote access to administration. We have included AnyConnect VPN, Premium license peers 2 so I guess we can just use of Cisco AnyConnect VPN client. I went to Cisco's Web site and it says that I don't have right to the last Anyconnect VPN Client 4.x but I don't have access to the version 3.x.
The 3.x client is compatible with the ASA and also Windows 10?
If Yes, what is the correct file to use, there are many files listed for download in AnyConnect 3.x?
In addition, what is the difference between the AnyConnect 3.x and 4.x customer and why Cisco restricting 4.x?
Jim
AnyConnect 4.x has changed the licensing model. AnyConnect 4.x licenses are term based licensing vs perpetual 3.x. There are a number of other differences, mainly due to there being only two license types - more and Apex - no Mobile plus, Advanced Endpoint Assessment, shared VPN etc. Cisco offers a nominal or no license cost of migration until the end of 2015. (depending on what you have: positive Essentials or Apex at premium)
AnyConnect 3.1 will work with Windows 10 and the latest version of the Software ASA (since Version 3.1.10010). Reference:
http://www.Cisco.com/c/en/us/TD/docs/security/vpn_client/AnyConnect/ANYC...
There are two ways it is distributed - as a stand-alone installation or package for the distribution of the ASA station. Both come in Windows, Mac OS X and Linux distributions. For a Windows client, you must use either:
AnyConnect-Win-3.1.12020-pre-deploy-K9.ISO
AnyConnect-victory - 3.1.12020 - k9.pkg
.. .to the current version of these respective form factors.
-
Router RV042 VPN Client access from Linux?
Hello world!
I have a question for the creators and users of RV042.
Is there a way to communicate with a Linux box for access on a RV042 VPN client? I'm trying to do that and play with the settings, but I am not able to connect. I tried profiles in OpenVPN, OpenSwan, kVPNc and others. For the most part, my problem is that all of these software require too many parameters and other certificates that only types that you can create on a RV042 (.pem files).
Please let me know if any of you were able to connect to a Linux box for on a RV042 VPN.
Also, I would ask the CISCO/Linksys people why they provide only a Windows client for this option? "Small companies" are devices not windows based commercial devices!
Thank you!
Zoli
Good day Zoli,
Unfortunately, there is not any Quickvpn client available for Linux and Macintosh which work together with the Small Business/Small Business routers Pro.
If I share your dismay that we do not formally use Quickvpn with all Linux distributions or any Mac OS, we have seen limited success with solutions that allow the use of third party VPN Clients when used in conjunction with our routers.
I'm curious to know whether or not you have explored Shrew Soft VPN Client (a simple Google search will yield results). I'm currently taking a look and to experiment a little bit on my end to see if there is anything we can get to work. If you can, please let me know what you use distribution, what version and a list of all customers third-party vpn that you used.
Personally, I'd love to see the development of a guide that we as support engineers to help all of our Linux-savvy customer.
Thanks for your patience!
-
We run MAC Snow Leopard (version 10.6.2). Is it possible to copy the profile instead of give the user education how to configure the VPN client? I don't want to give the group name and group password.
Thank you.
Laura
YUP, use the pcf file and ask the user to import the software vpn client. For example: -.
If you have windows box--> program files---> system cisco-->--> profiles-->.pcf files vpn client.
so, you can configure your desktop computer v [Ref customer with all the information and save it.] Then access these FCP files, which you can provide to users so that they can import on their vpn client. The cisco pcf same files are compatible with open source "shrewsoft client app" too.
It may be useful
Thank you
Manish
-
Allowing the VPN Clients to the management network - nat woes
Try to allow the VPNClient IPSEC access to the management network. packet trace stops on the vpn encrypt even through phase 7 States it's NAT EXEMPT, he said his tent still NAT by a static. The only thing I can think to put a rule of nat exempted for the subnet on the external interface.
Please notify. Thank you.
Phase: 1
Type: ACCESS-LIST
Subtype:
Result: ALLOW
Config:
Implicit rule
Additional information:
MAC access listPhase: 2
Type: FLOW-SEARCH
Subtype:
Result: ALLOW
Config:
Additional information:
Not found no corresponding stream, creating a new streamPhase: 3
Type:-ROUTE SEARCH
Subtype: entry
Result: ALLOW
Config:
Additional information:
in 0.0.0.0 0.0.0.0 outdoorsPhase: 4
Type: ACCESS-LIST
Subtype: Journal
Result: ALLOW
Config:
Access-group MANAGEMENT-IN in the management interface
access-list MANAGEMENT-IN-scope ip allowed any one
Additional information:Phase: 5
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional information:Phase: 6
Type: FOVER
Subtype: Eve-updated
Result: ALLOW
Config:
Additional information:Phase: 7
Type: NAT-FREE
Subtype:
Result: ALLOW
Config:
match ip MANAGEMENT 10.10.10.0 255.255.255.0 outside 172.18.0.32 255.255.255.240
Exempt from NAT
translate_hits = 3, untranslate_hits = 33
Additional information:Phase: 8
Type: NAT
Subtype:
Result: ALLOW
Config:
static (MANAGEMENT, outside) 203.23.23.75 10.10.10.10 netmask 255.255.255.255
MANAGEMENT ip 10.10.10.10 host game OUTSIDE of any
static translation at 203.23.176.75
translate_hits = 0, untranslate_hits = 1
Additional information:Phase: 9
Type: NAT
Subtype: host-limits
Result: ALLOW
Config:
static (MANAGEMENT, outside) 203.23.23.75 10.10.10.10 netmask 255.255.255.255
MANAGEMENT ip 10.10.10.10 host game OUTSIDE of any
static translation at 203.23.23.75
translate_hits = 0, untranslate_hits = 1
Additional information:Phase: 10
Type: VPN
Subtype: encrypt
Result: DECLINE
Config:
Additional information:Result:
input interface: MANAGEMENT
entry status: to the top
entry-line-status: to the top
output interface: OUTSIDE
the status of the output: to the top
output-line-status: to the top
Action: drop
Drop-reason: flow (acl-drop) is denied by the configured rule-EXCERPT FROM CONFIG-
CorpVPN to access extended list ip 10.10.10.0 allow 255.255.255.0 172.18.0.32 255.255.255.240
Access extensive list ip 172.18.0.32 CorpVPN allow 255.255.255.240 10.10.10.0 255.255.255.0mask 172.18.0.33 - 172.18.0.46 255.255.255.240 IP local pool CorpVPN
access-list MANAGEMENT-extended permitted tcp 172.18.0.32 255.255.255.240 host 10.10.10.11 eq ssh
access-list MANAGEMENT-extended permitted tcp 172.18.0.32 255.255.255.240 host 10.10.10.10 eq ssh
access-list MANAGEMENT-extended permitted tcp 172.18.0.32 255.255.255.240 host 10.10.10.13 eq 3389access-list 101 extended allow ip 10.10.10.0 255.255.255.0 172.18.0.32 255.255.255.240
NAT 0 access-list (MANAGEMENT) No.-NAT-DU-MGMT
access-list no.-NAT-DU-MGMT scope ip 10.10.10.0 allow 255.255.255.0 172.18.0.32 255.255.255.240CorpVPN to access extended list ip 10.10.10.0 allow 255.255.255.0 172.18.0.32 255.255.255.240
Access extensive list ip 172.18.0.32 CorpVPN allow 255.255.255.240 allinternal CorpVPN group strategy
attributes of Group Policy CorpVPN
value of server DNS 203.23.23.23
VPN - connections 8
VPN-idle-timeout 720
Protocol-tunnel-VPN IPSec l2tp ipsec
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list CorpVPN
the address value CorpVPN poolstype tunnel-group CorpVPN remote access
attributes global-tunnel-group CorpVPN
address pool CorpVPN
Group Policy - by default-CorpVPN
IPSec-attributes tunnel-group CorpVPN
pre-shared keyFirst of all, there is overlap crypto ACL with the VPN static L2L:
crypto ASA1MAP 10 card matches the address 101
access-list 101 extended allow ip 10.10.10.0 255.255.255.0 172.18.0.32 255.255.255.240
access-list 101 extended allow ip 172.18.0.32 255.255.255.240 10.10.10.0 255.255.255.0I would remove the 2 lines of ACL 101 above because it is incorrect.
Secondly, from the output of ' cry ipsec to show his ", you seem to be getting the ip address of the"jdv1.australis.net.au", not"CorpVPN"pool pool. Therefore, the No. NAT ACL on the management interface is incorrect. I would just add a greater variety of education no. NAT so that it covers all your ip pool:
access-list no.-NAT-DU-MGMT scope ip 10.10.10.0 allow 255.255.255.0 172.18.0.0 255.255.255.0
Thirdly, even with your dynamic ACL 'OUTSIDE_cryptomap_65535.65535' crypto map, it only covers the 172.18.0.32/28, so I just want to add a wider range since it seems you get the ip address of the different pool:
OUTSIDE_cryptomap_65535.65535 list of allowed ip extended access all 172.18.0.0 255.255.255.0
Then I would disable the following group of access for purposes of test first:
no access-group MANAGEMENT - OUT Interface MANAGEMENT
Finally, please clear all the SA on your ASA and xlate, then reconnect to your vpn client and test it again:
delete the ipsec cry his
clear the isa cry his
clear xlate
Please let us know how it goes after the changes. If it still doesn't work, please please send again the last configuration and also to send the output of the following:
See the isa scream his
See the ipsec scream his
and a screenshot of the page of statistics on your vpn client. Thank you.
-
How to put all through traffic the easy vpn client VPN server
Hi people
I want to ask you, how to put all of the server the easy vpn client VPN traffic through.
I mean, I have a server vpn at home, and if I connect to the vpn from outside server, to be with an IP address of my home.
There is the configuration up to now. Where is the problem?
ROUTER1 #sh running-config
Building configuration...
Current configuration: 5744 bytes
!
! Last configuration change at 19:51:18 UTC Wed Sep 4 2013 by cska
!
version 15.1
horodateurs service debug datetime msec
Log service timestamps datetime msec
no password encryption service
!
ROUTER1 hostname
!
boot-start-marker
usbflash0:CVO boot-BOOT Setup. CFG
boot-end-marker
!
!
!
AAA new-model
!
!
AAA authentication login ciscocp_vpn_xauth_ml_1 local
AAA authorization ciscocp_vpn_group_ml_1 LAN
!
!
!
!
!
AAA - the id of the joint session
!
Service-module wlan-ap 0 autonomous bootimage
Crypto pki token removal timeout default 0
!
Crypto pki trustpoint TP-self-signed-1604488384
enrollment selfsigned
name of the object cn = IOS - Self - signed - certificate - 1604488384
revocation checking no
!
!
TP-self-signed-1604488384 crypto pki certificate chain
certificate self-signed 01
3082022B 30820194 02020101 300 D 0609 2A 864886 F70D0101 04050030 A0030201
2 060355 04031326 494F532D 53656 C 66 2 AND 536967 6E65642D 43657274 31312F30
69666963 31363034 34383833 6174652D 3834301E 170 3133 30383239 31313539
32395A 17 0D 323030 31303130 30303030 305A 3031 06035504 03132649 312F302D
4F532D53 5369676E 656C662D 43 65727469 66696361 74652 31 36303434 65642D
38383338 3430819F 300 D 0609 2A 864886 01050003, 818, 0030, 81890281 F70D0101
8100CD 57 F1436ED2 8D9E8B99 B6A76D45 FE56716D D99765A9 1722937C F5603F9F
528E27AF 87A24C3D 276FBA1C A5E7C580 CE99748E 39458C 74 862C 2870 16E29F75
7A7930E1 15FA5644 D7ECF257 BF46C470 A3A17AEB 7AB56194 68BFB803 144B7B10
D3722BDD D1FD5E99 8068B77D A1703059 9F0578C7 F7473811 0421490D 627F25C5
4 HAS 250203 010001A 3 53305130 1 130101 FF040530 030101FF 301F0603 0F060355
551 2304 18301680 141B 1326 C111DF7F 9F4ED888 EFE2999A 4C50CDD8 06 12301
03551D0E 04160414 1B1326C1 11DF7F9F 4ED888EF E2999A4C 50CDD812 300 D 0609
2A 864886 04050003 81810096 BD0C2B16 799DB6EE E2C9B7C4 72FEAAAE F70D0101
FF87465C FB7C5248 CFA08E68 522EA08A 4B18BF15 488D D53D9A43 CB400B54 8006
CB21BDFB AA27DA9C C79310B6 BC594A7E D6EDF81D 0DB7D2C1 9EF7251B 19A 75403
211B1E6B 840FE226 48656E9F 67DB4A93 CE75045B A986F0AD 691EE188 7FB86D3F
E43934FA 3D62EC90 8F37590B 618B0C
quit smoking
IP source-route
!
!
!
!
CISCO dhcp IP pool
import all
network 192.168.1.0 255.255.255.0
DNS-server 195.34.133.21 212.186.211.21
default router 192.168.1.1
!
!
IP cef
No ipv6 cef
!
Authenticated MultiLink bundle-name Panel
license udi pid CISCO892W-AGN-E-K9 sn FCZ1530C209
!
!
username privilege 15 secret 5 cska $1$ $8j6G 2sMHqIxJX8MQU6vpr75gp1
!
!
!
!
!
!
crypto ISAKMP policy 1
BA 3des
preshared authentication
Group 2
!
Configuration group customer isakmp crypto VPNGR
vpngroup key
DNS 212.186.211.21 195.34.133.21
WINS 8.8.8.8
domain chello.at
pool SDM_POOL_1
ACL 120
netmask 255.255.255.0
ISAKMP crypto ciscocp-ike-profile-1 profile
match of group identity VPNGR
client authentication list ciscocp_vpn_xauth_ml_1
ISAKMP authorization list ciscocp_vpn_group_ml_1
client configuration address respond
virtual-model 1
!
!
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
!
Profile of crypto ipsec CiscoCP_Profile1
security association idle time 86400 value
game of transformation-ESP-3DES-SHA
set of isakmp - profile ciscocp-ike-profile-1
!
!
Bridge IRB
!
!
!
!
interface Loopback0
192.168.4.1 IP address 255.255.255.0
IP nat inside
IP virtual-reassembly in
!
interface BRI0
no ip address
encapsulation hdlc
Shutdown
Multidrop ISDN endpoint
!
interface FastEthernet0
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
!
interface FastEthernet4
!
interface FastEthernet5
!
FastEthernet6 interface
!
interface FastEthernet7
!
interface FastEthernet8
no ip address
Shutdown
automatic duplex
automatic speed
!
type of interface virtual-Template1 tunnel
IP unnumbered Loopback0
ipv4 ipsec tunnel mode
Tunnel CiscoCP_Profile1 ipsec protection profile
!
interface GigabitEthernet0
Description Internet
0023.5a03.b6a5 Mac address
customer_id GigabitEthernet0 dhcp IP address
NAT outside IP
IP virtual-reassembly in
automatic duplex
automatic speed
!
wlan-ap0 interface
description of the Service interface module to manage the embedded AP
192.168.9.2 IP address 255.255.255.0
ARP timeout 0
!
interface GigabitEthernet0 Wlan
Description interface connecting to the AP the switch embedded internal
!
interface Vlan1
no ip address
Bridge-Group 1
Bridge-Group 1 covering-disabled people
!
interface BVI1
IP 192.168.1.1 255.255.255.0
IP nat inside
IP virtual-reassembly in
!
local IP SDM_POOL_1 192.168.4.3 pool 192.168.4.245
IP forward-Protocol ND
!
!
IP http server
local IP http authentication
IP http secure server
overload of IP nat inside source list 110 interface GigabitEthernet0
IP nat inside source static tcp 192.168.1.5 3389 interface GigabitEthernet0 3389
IP nat inside source static udp 192.168.1.5 3389 interface GigabitEthernet0 3389
IP nat inside source static tcp 192.168.1.5 21 interface GigabitEthernet0 21
IP nat inside source static udp 192.168.1.5 21 interface GigabitEthernet0 21
IP nat inside source static tcp 192.168.1.4 3389 interface GigabitEthernet0 3390
IP nat inside source static udp 192.168.1.4 3389 interface GigabitEthernet0 3390
overload of IP nat inside source list 120 interface GigabitEthernet0
IP route 0.0.0.0 0.0.0.0 dhcp
!
exploitation forest esm config
access list 101 ip allow a whole
access-list 110 permit ip 192.168.1.0 0.0.0.255 any
access list 111 permit tcp any any eq 3389
access-list 120 allow ip 192.168.4.0 0.0.0.255 any
!
!
!
!
!
!
!
control plan
!
Bridge Protocol ieee 1
1 channel ip bridge
!
Line con 0
line 2
no activation-character
No exec
preferred no transport
transport of entry all
transport output pad rlogin udptn ssh telnet
line to 0
line vty 0 4
privilege level 15
preferred transport ssh
entry ssh transport
transportation out all
!
Thanks in advance
To do this you must make the following changes:
(1) disable split Tunneling by deleting the ACL of your configuration of the client group.
(2) enable NAT for VPN traffic by adding 'ip nat inside' to your virtual model of the client network to the ACL that controls your PAT.Edit: Theses are the changes to your config (also with a little cleaning):
Configuration group customer isakmp crypto VPNGR
No 120 LCD
!
type of interface virtual-Template1 tunnel
IP nat inside
!
no nat ip inside the source list 120 interface GigabitEthernet0 overload
!
access-list 110 permit ip 192.168.4.0 0.0.0.255 any
no access-list 120 allow ip 192.168.4.0 0.0.0.255 any
Sent by Cisco Support technique iPad App
-
ASA problem inside the VPN client routing
Hello
I have a problem where I can't reach the VPN clients with their vpn IP pool from the inside or the asa itself. Connect VPN clients can access internal network very well. I have no nat configured for the pool of vpn and packet trace crypt packages and puts it into the tunnel. I'm not sure what's wrong.
Here are a few relevant config:
network object obj - 192.168.245.0
192.168.245.0 subnet 255.255.255.0
192.168.245.1 - 192.168.245.50 vpn IP local pool
NAT (inside, outside) static source any any destination static obj - 192.168.245.0 obj - 192.168.245.0 no-proxy-arp-search to itinerary
Out of Packet trace:
Firewall # entry packet - trace inside the x.x.x.x icmp 8 0 192.168.245.33
Phase: 1
Type: ACCESS-LIST
Subtype:
Result: ALLOW
Config:
Implicit rule
Additional information:
MAC access list
Phase: 2
Type:-ROUTE SEARCH
Subtype: entry
Result: ALLOW
Config:
Additional information:
in 192.168.245.33 255.255.255.255 outside
Phase: 3
Type: ACCESS-LIST
Subtype: Journal
Result: ALLOW
Config:
Access-group acl-Interior interface inside
access list acl-Interior extended icmp permitted an echo
Additional information:
Phase: 4
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional information:
Phase: 5
Type: INSPECT
Subtype: np - inspect
Result: ALLOW
Config:
Additional information:
Phase: 6
Type:
Subtype:
Result: ALLOW
Config:
Additional information:
Phase: 7
Type: NAT
Subtype:
Result: ALLOW
Config:
NAT (inside, outside) static source any any destination static obj - 192.168.245.0
obj - 192.168.245.0 no-proxy-arp-search to itinerary
Additional information:
Definition of static 0/x.x.x.x-x.x.x.x/0
Phase: 8
Type: VPN
Subtype: encrypt
Result: ALLOW
Config:
Additional information:
Phase: 9
Type: CREATING STREAMS
Subtype:
Result: ALLOW
Config:
Additional information:
New workflow created with the 277723432 id, package sent to the next module
Result:
input interface: inside
entry status: to the top
entry-line-status: to the top
output interface: outside
the status of the output: to the top
output-line-status: to the top
Action: allow
There is no route to the address pool of vpn. Maybe that's the problem? I don't know than that used to work before we went to 8.4.
Check if the firewall is enabled on your host from the client ravpn and blocking your pings.
-
Hi guru of cisco
Help me please to configure VPN access on ASA 5505 for Cisco VPN Client. I want to let the customers gateway, but access remote 192.168.17.0/24 and 192.168.10.0/24 (connected through site-to-site) networks.
Will be much appreciated for your help.
My config:
Output from the command: 'display conf '.
!
ASA Version 8.2 (2)
!
name of host host1
domain domain name
activate the encrypted password password
encrypted passwd password
names of
!
interface Vlan1
Description INTERNET
0000.0000.0001 Mac address
nameif WAN
security-level 0
IP address a.a.a.a 255.255.255.248 watch a1.a1.a1.a1
OSPF cost 10
!
interface Vlan2
OLD-PRIVATE description
0000.0000.0102 Mac address
nameif OLD-private
security-level 100
IP 192.168.17.2 255.255.255.0 watch 192.168.17.3
OSPF cost 10
!
interface Vlan6
Description MANAGEMENT
0000.0000.0106 Mac address
nameif management
security-level 100
IP 192.168.1.2 255.255.255.0 ensures 192.168.1.3
OSPF cost 10
!
interface Vlan100
Failover LAN Interface Description
!
interface Ethernet0/0
!
interface Ethernet0/1
Shutdown
!
interface Ethernet0/2
Shutdown
!
interface Ethernet0/3
Shutdown
!
interface Ethernet0/4
Shutdown
!
interface Ethernet0/5
switchport access vlan 100
!
interface Ethernet0/6
switchport trunk allowed vlan 2.6
switchport mode trunk
!
interface Ethernet0/7
Shutdown
!
boot system Disk0: / asa822 - k8.bin
passive FTP mode
DNS domain-lookup WAN
DNS server-group DefaultDNS
Server name dns.dns.dns.dns
domain domain name
permit same-security-traffic intra-interface
object-group Protocol TCPUDP
object-protocol udp
object-tcp protocol
object-group service RDP - tcp
RDP description
EQ port 3389 object
object-group Protocol DM_INLINE_PROTOCOL_1
ip protocol object
icmp protocol object
object-protocol udp
object-tcp protocol
Access extensive list ip 192.168.17.0 LAN_nat0_outbound allow 255.255.255.0 192.168.10.0 255.255.255.0
Standard access list LAN_IP allow 192.168.17.0 255.255.255.0
WAN_access_in list of allowed ip extended access all any debug log
WAN_access_in list extended access allowed icmp a.a.a.a 255.255.255.248 192.168.10.0 255.255.255.0 inactive debug log
WAN_access_in list extended access permit tcp any object-group RDP any RDP log debugging object-group
WAN_access_in list extended access allowed icmp a.a.a.a 255.255.255.248 a.a.a.a 255.255.255.248 debug log
MANAGEMENT_access_in list of allowed ip extended access all any debug log
access-list extended OLD-PRIVATE_access_in any allowed ip no matter what debug log
access-list OLD-PRIVATE_access_in allowed extended object-group DM_INLINE_PROTOCOL_1 interface OLD-private 192.168.10.0 255.255.255.0 inactive debug log
access-list OLD-PRIVATE_access_in allowed extended object-group TCPUDP interface OLD-private no matter what inactive debug log
access-list OLD-PRIVATE_access_in allowed extended icmp host 192.168.10.254 interface private OLD newspaper inactive debugging
access-list OLD-PRIVATE_access_in allowed extended icmp host 192.168.17.155 interface private OLD newspaper debugging
access-list 101 extended allow host tcp 192.168.10.7 any eq 3389 debug log
Access extensive list ip 192.168.17.0 WAN_1_cryptomap allow 255.255.255.0 192.168.10.0 255.255.255.0
WAN_1_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.10.0 255.255.255.0
WAN_cryptomap_2 to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.10.0 255.255.255.0
Capin list extended access permit ip host 192.18.17.155 192.168.10.7
Capin list extended access permit ip host 192.168.10.7 192.168.17.155
LAN_access_in list of allowed ip extended access all any debug log
Access extensive list ip 192.168.17.0 WAN_nat0_outbound allow 255.255.255.0 192.168.10.0 255.255.255.0
WAN_nat0_outbound list of allowed ip extended access all 192.168.17.240 255.255.255.252
WAN_nat0_outbound to access extended list ip 192.168.2.0 allow 255.255.255.0 192.168.2.0 255.255.255.248
Access extensive list ip 192.168.17.0 WAN_2_cryptomap allow 255.255.255.0 192.168.10.0 255.255.255.0
permit inside_nat0_outbound to access extended list ip 192.168.10.0 255.255.255.0 192.168.17.0 255.255.255.0
LAN_IP_inbound list standard access allowed 192.168.10.0 255.255.255.0
Standard access list IPSec_VPN_splitTunnelAcl allow a
access extensive list ip 192.168.17.0 vpnusers_splitTunnelAcl allow 255.255.255.0 any
sheep - in extended Access-list allow IP 192.168.17.0 255.255.255.0 192.168.2.0 255.255.255.0
vpn_ipsec_splitTunnelAcl list standard access allowed 192.168.2.0 255.255.255.0
pager lines 24
Enable logging
logging trap information
asdm of logging of information
Debugging trace record
MTU 1500 WAN
MTU 1500 OLD-private
MTU 1500 management
mask 192.168.1.150 - 192.168.1.199 255.255.255.0 IP local pool VPN_Admin_IP
IP local pool vpnclient 192.168.2.1 - 192.168.2.5 mask 255.255.255.0
failover
primary failover lan unit
failover lan interface failover Vlan100
15 75 holdtime interface failover pollTime
key changeover *.
failover interface ip failover 192.168.100.1 255.255.255.0 ensures 192.168.100.2
ICMP unreachable rate-limit 1 burst-size 1
ICMP permitted host b.b.b.b WAN
ICMP allow 192.168.10.0 255.255.255.0 WAN
ICMP permitted host c.c.c.c WAN
ICMP allow 192.168.17.0 255.255.255.0 WAN
ICMP deny any WAN
ICMP permitted host OLD-private b.b.b.b
ICMP allow 192.168.10.0 255.255.255.0 OLD-private
ICMP allow 192.168.17.0 255.255.255.0 OLD-private
ICMP permitted host c.c.c.c OLD-private
ICMP permitted host b.b.b.b management
ICMP permitted host 192.168.10.0 management
ICMP permitted host 192.168.17.138 management
ICMP permit 192.168.1.0 255.255.255.0 management
ICMP permitted host 192.168.1.26 management
ASDM image disk0: / asdm - 631.bin
don't allow no asdm history
ARP timeout 14400
Global (WAN) 1 interface
Global (OLD-private) 1 interface
Global interface (management) 1
NAT (OLD-private) 0-list of access WAN_nat0_outbound
NAT (OLD-private) 1 0.0.0.0 0.0.0.0
WAN_access_in access to the WAN interface group
Access-group interface private-OLD OLD-PRIVATE_access_in
Access-group MANAGEMENT_access_in in the management interface
Route WAN 0.0.0.0 0.0.0.0 a.a.a.185 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
the ssh LOCAL console AAA authentication
local AAA authentication attempts 10 max in case of failure
Enable http server
http 192.168.1.0 255.255.255.0 WAN
http 0.0.0.0 0.0.0.0 WAN
http a.a.a.a 255.255.255.255 WAN
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Service resetoutside
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
card crypto WAN_map 1 corresponds to the address WAN_1_cryptomap
card crypto WAN_map 1 set peer b.b.b.b
WAN_map 1 transform-set ESP-DES-SHA crypto card game
card crypto WAN_map WAN interface
ISAKMP crypto enable WAN
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
crypto ISAKMP policy 30
preshared authentication
the Encryption
sha hash
Group 1
life 86400
Telnet timeout 5
SSH b.b.b.b 255.255.255.255 WAN
SSH timeout 30
SSH version 2
Console timeout 0
dhcpd auto_config OLD-private
!a basic threat threat detection
host of statistical threat detection
Statistics-list of access threat detection
a statistical threat detection tcp-interception rate-interval 30 burst-400-rate average rate 200
NTP server 129.6.15.28 source WAN prefer
WebVPN
attributes of Group Policy DfltGrpPolicy
Protocol-tunnel-VPN IPSec svc webvpn
internal admin group strategy
group admin policy attributes
DNS.DNS.DNS.DNS value of DNS server
Protocol-tunnel-VPN IPSec
internal vpn_ipsec group policy
attributes of the strategy of group vpn_ipsec
value 192.168.17.80 DNS server dns.dns.dns.dns
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list vpn_ipsec_splitTunnelAcl
the address value vpnclient pools
username admin password encrypted password privilege 15
n1ck encrypted password privilege 15 password username
type tunnel-group admin remote access
tunnel-group admin general attributes
address pool IPSec_VPN_pool
vpnclient address pool
LOCAL authority-server-group
strategy-group-by default admin
tunnel-group admin ipsec-attributes
pre-shared-key *.
tunnel-group b.b.b.b type ipsec-l2l
tunnel-group b.b.b.b General-attributes
strategy-group-by default admin
b.b.b.b tunnel ipsec-attributes group
pre-shared-key *.
NOCHECK Peer-id-validate
type tunnel-group vpn_ipsec remote access
tunnel-group vpn_ipsec General-attributes
vpnclient address pool
Group Policy - by default-vpn_ipsec
vpn_ipsec group of tunnel ipsec-attributes
pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
inspect the icmpThanks a lot for the confirmation. There is some lack of configurations and also some configuration errors.
They are here:
(1) Split tunnel-access list is incorrect:
vpn_ipsec_splitTunnelAcl list standard access allowed 192.168.2.0 255.255.255.0
It should be allowed in your internal network. Please, add and remove the following:
standard access list vpn_ipsec_splitTunnelAcl allow 192.168.17.0 255.255.255.0
No vpn_ipsec_splitTunnelAcl of the standard access list only allowed 192.168.2.0 255.255.255.0
(2) NAT 0-list of access should also include the traffic between the local subnet to the Pool of IP VPN:
Access extensive list ip 192.168.17.0 WAN_nat0_outbound allow 255.255.255.0 192.168.2.0 255.255.255.0
(3) dynamic-map has not been created and assigned to crypto card:
Crypto-map dynamic dynmap 10 game of transformation-ESP-3DES-SHA
card crypto ipsec WAN_map 65000-isakmp dynamic dynmap
(4) Finally, you have not enabled protocol IPSec in your group strategy:
attributes of the strategy of group vpn_ipsec
Protocol-tunnel-VPN IPSec
Hope that helps.
If it still does not after the changes described above, please kindly share the latest config and also the output of the following debugs when you try to connect:
debugging cry isa
debugging ipsec cry
-
Cisco VPN Client causes a blue screen crash on Windows XP Pro (Satellite M30)
Hello
I have a Satellite Pro M30 running Windows XP Professional.
After you start a vpn Tunnel via a customer of Cisco VPN (Version 4.6 and 4.7), the system crashes with a blue screen.
I see that the key exchange is successful, but immediately after the vpn connection is established Windows XP crashes with a blue screen.
Someone has any idea how to solve this problem?
Perhaps by the updated device driver? And if so, which driver should be updated?
Kind regards
Thorsten
Hello
Well, it seems that the Cisco client is a problem.
I m unaware of this product because it of not designed by Toshiba.
I think that the drivers are not compatible with the Windows operating system.
However, I found this site troubleshooting cisco vpn client:
Please check this:
http://www.CITES.uiuc.edu/wireless/trouble-index.html -
R7000 vpn client.crt file is empty
My version is 1.0.4.30_1.1.67.
After you generate files of VPNs, client.crt file is empty 0 byte.
The other files are correct.
Can anyone help?
Thank you.
Hi @jli
Welcome to the community!
Try to use the latest beta of firmware 1.0.5.60.
-
windows\system32\vsinit.dll
I try to run CISCO "VPN Client" connect from my PC at home for my work PC.
Then, I get a message:
Validation failed for C:\WINDOWS\System32\VSINIT.dll
Any ideas?
Martin
Hello
Run the checker system files on the computer. Link, we can see: Description of Windows XP and Windows Server 2003 System File Checker (Sfc.exe): http://support.microsoft.com/kb/310747
Note that: if he asks you the service pack CD, follow these steps from the link: you are prompted to insert a Windows XP SP2 CD when you try to run the tool on a Windows XP SP2 computer system File Checker: http://support.microsoft.com/kb/900910 (valid for Service pack 3)
If the steps above is not enough of it please post your request in the TechNet forum for assistance: http://social.technet.microsoft.com/Forums/en/category/windowsxpitpro
Maybe you are looking for
-
Nothing in the worm 29 bookmarks sidebar. How to bring back my favorites?
I have my favorites in folders. They are always in the bookmarks drop-down menu, but not in the sidebar. Nothing does highlight or shows by mousing over the Favorites sidebar area.
-
How to disable the TouchPad 'tap to click' on Satellite A200 - 15L Vista
Until mid-December, I got the Synaptics Touchpad ' tap to click on "disabled. Then it became somehow activated, the context menu item to change to gray and the properties of the mouse, etc. settings contain no reference to it. It was suggested that u
-
I changed my email address where I received notifications. How can I register my new address?
-
* Original title: start and stop Hi team - can - you advise me here on this point - we have Windows 7 premium and during the signing of the computer, (and we closed everything out, I believe) it takes forever to close... We get a message that says "i
-
Guard printer goes offline and create a copy of the printer
Hello I have a printer that does not have very easily the first time. First time, I actually connected via usb first and then installed driver after. I then deleted and did the opposite way around. This seemed to work properly. However, it will work