The ID attribute of the station call needs for Anyconnect VPN client MAC address

Similar Questions

• MAC and PC can reach the same an ASA for Anyconnect VPN?

  Hi, we have MAC and PC users. We configure the Anyconnect VPN in an ASA. But two users need two image of sorts. We must therefore use the two commands:

  AnyConnect image disk0: / anyconnect -win- 3.1.04066 - k9.pkg

  AnyConnect image disk0: / anyconnect -macosx- i386 - 2.5.2014 - k9.pkg.

  This is what two commands cannot coexist in an ASA. How to solve the problem? I hope your suggestion. Thank you

  They can co-exist, but you must add different sequence numbers at the end of each command.

• Select the timeout on ASA Cisco Anyconnect VPN

  Hello world

  I use the Cisco Anyconnect VPN client with the ASA 5540 firewall. I need allow a time-out on the VPN clients, so they log off after x hours of inactivity.

  Thank you to

  Best respect

  Hello

  To my understanding of the default timeout value is 30 minutes

  You should be able to change this setting in the "username" configurations (if you use LOCAL AAA on the SAA) or under the configurations of the 'group policy' .

  The command is

  VPN-idle-timeout

  Here is the link of the commands reference

  http://www.Cisco.com/c/en/us/TD/docs/security/ASA/ASA-command-reference/...

  -Jouni

• When a computer XP starts, the following errors occur. Can't find Mac addresses, can't find DHCP at startup. PC is not connected to a network. Why would it gives this error at startup.

  When a computer XP starts, the following errors occur. Can't find Mac addresses, can't find DHCP at startup. PC is not connected to a network.

  Why would it gives this error at startup?

  It is not a Windows problem, it happens very early in the boot process until Windows is still a part of the image.  Your computer is configured for a remote network via PXE boot and there is no this PXE server so that you get this error message.  With PXE network boot, you can start a computer without him having a hard drive, the operating system resides on another machine on the network.  When the BIOS does not find the PXE server it gives you the error message, and then it proceeds to the next start equipment, which is probably your local hard drive.  Go into the BIOS and disable the PXE boot option or move it to the bottom of the boot order so that the hard drive is set as the primary boot device.

  John

• Cisco AnyConnect VPN Client (connection attempt failed because the network or pc problem cisco)

  Hi all

  I am trying to connect to my Cisco AnyConnect VPN Client but everytime I try, I get an error (connection attempt failed because the network or pc problem cisco)

  Can anyone help me please with this.

  Thank you

  Zia

  What is the local firewall on your computer?

• Where is the often called "Toolbox" for the more than 8600 OfficeJet

  I can't find a title or link or separate call software "Toolbox" on any of the software that comes with most 8600. But aid and support elements continue to say to go to the Toolbox. It never says where he is supposed to be found, but there is no element to choose called Toolbox when I arrive at the end of the path that is Maintenance tasks. Where is this thing called the Toolbox?

  Well, this link is conceptually the solution, although not quite right in my case. For my 8600 more, from the start / all programs on go in the hp/8600 folder and click the file 8600. There is no mention of Printer Wizard, but you receive seems to be roughly the same set of things and seems to be in general what is referred to as the Toolbox. Unfortunately various different paths you can follow do not exactly corresponding elements of manual or assistance that are provided.  At the end of the day, to look for and colleagues.

  At least this "solution" makes it clear that it is not just me who can not find things in the software hp which is supposed to be there. I like hp printers, but it software often has the seeds that they seem reluctant to do anything to the subject. Well.

• desktop computers to linger in the folder 'inaccessible Agent' for a long time, apipa address might be a clue

  Hi all

  We run see 6.1.1 with linked clone Windows 7 desktops. Lately, some workstations hang in the State 'inaccessible Agent' for what seems like 15 or 20 minutes until they are refreshed. We have pools set on closing session and refreshment after 1 minute if disconnected. We noticed that desktop in this weird State have an apipa for the virtual NETWORK adapter address (starts with 169.254.x.x). If go us to the office as local administrator and do an ipconfig / renew, it will get a valid IP address on our network and as soon as it gets a valid IP address, he leaves the "Agent unreachable" queue and passes by the update process. It seems that Conversely, we can get these desktop computers to process more quickly is to remove them.

  This is not an isolated machine virtual on a particular ESXi host (I saw him arrive on all hosts) and when I look for ESXi hosts network settings, I see that the virtual machines in question are related to the virtual switch. I ensured that the virtual switch has enough ports (120) and I checked the DHCP servers, and there are a lot of IPs available in the subnet where live virtual offices.

  Also, it does not seem to be isolated to a pool, we see in a pool that uses the management of the Persona and a swimming pool which is not.

  Any thoughts on how to solve the problems?

  Thank you!

  Don't know it could help you, but we have IP private address automatically on our vdi error (it worked fine, but it broke after an update) we had to close 1 our DHCP servers (we had 2) since then, then all is back to normal. We will need to track DHCP to know exactly what is the cause of the problem none of our dhcp gave a clue at the time.

• With the help of ASA for our VPN

  I was curious, if through the ASDM, there is a way to show that was recorded in the last week and for how long?  I know through the CLI I can use the sh sessiondb-vpn l2l to see who is connected, but trying to get a report of its total use by user, date and time?

  Hi Dan,.

  The ASA does not all historical data connections so it won't be possible.

  You can view the users connected to the part followed by ASDM but you do not have the reporting features.

  Kind regards

  Nicolas

• Inside the server can't ping remote vpn client

  My simple vpn client can accumulate the tunnel vpn with my Office ASA5510 success and my vpn client can ping the internal server. But my internal server cannot ping the remote vpn client. Even the firewall vpn client windows is disable.

  1. in-house server can ping Internet through ASA.

  2 internal server cannot ping vpn client.

  3 Vpn client can ping the internal server.

  Why interal Server ping vpn client? ASA only does support vpn in direction to go?

  Thank you.

  Hello

  Enable inspect ICMP, this should work for you.

  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the icmp
  inspect the icmp error

  inspect the icmp

  

  To configure the ICMP inspection engine, use the command of icmp inspection in class configuration mode. Class configuration mode is accessible from policy map configuration mode.

  inspect the icmp

  HTH

  Sandy

• Is Edge inspect the desktop to the internet connection sharing (for example, VPN) or just the same WIFI network?

  I'm asking because on my work VPN all our screening sites are behind the firewall and so curious if my android device running the Dashboard Viewer inspect also share this VPN connection or if the cutting-edge office essentially comes the camera to a normal URL? The unit doesn't have native VPN access.

  I am unable to test this, because our company blocks all Chrome extensions, and before I go through a long process to unlock this particular extension I just want to see if it would work I described.

  
  Thank you!

  Inspect edge relies on your local network for communication. Many VPN services will seal your machine connected to your local network when the VPN tunnel is open. Inspect edge does not work in this situation. Ask your VPN administrator to determine if there are parameters that will allow you to access your local network when connected to the VPN. Yes, the desktop application pointing devices to the url and the url must be accessible by the network device is connected to.

  In addition, Port 7682 is required by Edge inspect. If another application or service is using this port, you must reconfigure either to use a different port or close Edge to inspect work.

• need help in the form of need for a method to calculate end_issue... function

  I have a tabular presentation
  with the following fields
  SNO, offers, no_of_issues, start_issue and end_issue
  At the time where the user chooses to provide
  and start_issue selects a number of months
  end question must be calculated.
  
  Select no_of_issues in the mnoofissues of supply where offer = moffer;
  end_issue = start_issue + mnoofissues;
  
  so once when a user enters start_issue I have need of the value of end_issue must be calculated...
  end_issue = start_issue + mnoofissues;
  
  Can help...
  I'm not familiar with java. But seems that java is the only one. Are there easier methods.
  
  Published by: zycoz100 on October 21, 2012 19:37

  Are there easier methods.

  Nope.

  The next thread can help you with the update, but certainly not in the category of 'easy' even with assistance.
  Dynamic action on slot-shaped table

• Install service pack 3 Windows xp pro takes care of the missing DLLs needed for kernels. the mine antivirus program deleted some critical files

  from the start, windows fails to launch and a message of error due to the missing dll files is displayed

  If Windows does not start, you can not install Service Pack 3. And no, it is unlikely that your computer could get repaired by doing so, even if you were able to try. Try a repair rather installation:

  http://www.michaelstevenstech.com/XPrepairinstall.htm - repair install how-to MS - MVP - Elephant Boy computers - Don ' t Panic!

• Computer cannot read the .vp3 files needed for my embroidery software

  Title: original .vp3

  I try to install the embroidery software that came with my new sewing machine and although pilots seem to have installed ok I can't access embroidery designs, because the computer says that it cannot read the .vp3 files.  Why he cannot read, and how do I read that I can use on the machine.  Someone told all the answers no computer talk please.

  Unfriendly computers Hello,

  I'm not very familiar with the .vp3 extension but do not know that it is an extension that Pfaff is normally used. Look at the link below, because it gives the means of obtaining the .vp3 on a Windows machine.
  http://www.PFAFF.com/ca/en/media/CA/PF_INSTRUCTIONS.PDF

  Your program is not compatible with Windows 7. Check and see if you can use compatibility mode.
  Compatibility mode is incorporated on your computer, when you right-click on any application or program and select it properties, you have a Compatibility tab.
  In compatibility mode, we have options to manually change the settings.

  If you have problems with a program that worked correctly on an earlier version of Windows, select the compatibility mode that corresponds to this version.
  Run this program in compatibility mode for:
  Select the Compatibility tab: you can choose to run the program in Windows XP compatibility mode, or even all the way back to Windows 95 compatibility

  See the below link for more information about the same:make sure to run older programs in this version of Windows: http://windows.microsoft.com/en-US/windows7/Make-older-programs-run-in-this-version-of-Windows

  Please let us know if this helps solve your problem.

  Sincerely,

  .

  Marilyn
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• The modules I need for LiveCycle Output?

  Hello

  We want to install ss4 LC for outputmanagement. No other modules are allowed.

  Which modules to choose at this point?

  

  Thx for the help...

  Regards Axel

  LCM would take care of the required modules, and won't let you go forward. It should be output + Content Repository

  Thank you

  Wasil

• in photoshop CC 2014 where the oil painting filtered go? It's the filter I need for almost every picture

  I can't find the filter of painting oil more in recent version, it is not hidden in the painting galleries. I hope that Adobe didn't understand it otherwise I can't use updates more...

  Hello, it is not available in CC (2014) so why it is installed next to CC.

  The info was published a few months ago: http://blogs.adobe.com/photoshopdotcom/2014/04/photoshop-spring-cleaning.html