Implementation of scanning with old HP R80

Similar Questions

• scan with ni9401 mode

  Hello, I use the scan mode and the module ni9401, and I'm under codes in labview with a timed loop

  When I try to change the loop timed to dt = microsec and scan period<1ms in="" compact="">

  Compact rio is disconnected! why I got this problem?

  Maybe I can use scanning with scan time mode<>

  Hi, mariomoskis,

  Unfortunately, this is part of the limitation of the scan Mode. You can basically think of scan mode as a train that toured all the modules collects data and it falls on the drive and there is only 1 train for the entire system and it runs at a speed (scanning speed). The fact train one passes each interval of scanning speed, so if you want to produce a train of pulses to a little less than 1 kHz you will get aliasing. However, cRIO should unplug any, I don't know what the problem is here, but it seems closely related.

  There are two solutions to this problem, but the two would require changes.
  1. you can avoid all these problems and the resolution time get down to a 25ns (or less) If you set the mode FPGA. We can use the existing code of NI.com/IPnet to implement a pulse generator to train with the custom calendar settings and pulse on any module.

  2. some modules support digital modes specialized, making essentially a pre-built section of the FPGA code (in scan mode) that support some common functions such as Pulse Width Modulation. With these modules, you can request a rate (which will update at 1 kHz)-specific, but the actual timetable for the module is managed at the hardware level. There are only a few modules that support it, and they are listed in the link below.

  KB 55L06EMO: what Support Modules of the series C, specialty digital functions in Scan Mode?
  http://digital.NI.com/public.nsf/allkb/2664A3D35D9F79A4862576B300277E35?OpenDocument

  I hope this helps.

  Saludos!

  Jesus

• Cannot scan with c309g on the new iMac

  Later Cougar (USB), after you install later (= old) Driver HP and on top of this apple driver (meticulously followed the advice of the post Printdoc 19/08/2009). Printing is fine, do not scan: using system prefs > print & scan > open scanner I get only a gray window. The same phenomenon occurs via Preview. "HP Scan" HP program hangs after clicking "scan" and must be out of force.

  I'll take a look at the following document I linked below.

  OS X 10.7 Lion: install and use the printer with Lion

  There is a section in the document entitled "How to scan with the Apple Software Update driver" who should have the information you're looking for.

• DESKJET 3050 ALL - IN - ONE J610: scanning documents old printer/scanner

  EASY, I HAVE TO FOLLOW THE DIRECTIONS ON THE SCAN INTO A WORD DOCUMENT OR EMAIL. I HAVE A SCAN BUTTON, BUT I DON'T KNOW HOW TO SO HE COULD ANALYZE. IT SIMPLY PRINTS ANOTHER COPY!

  THE PRINTER IS OLD, RELATIVELY SPEAKING (MAYBE 4-5 YEARS) AND I DON'T REMEMBER IF I'VE EVER USED THE SCAN FUNCTION. I USE WINDOWS 7.

  PRODUCT NUMBER: CN [personal information]. HELP APPRECIATED

  Hi @Grandmatothree,

  Welcome to the HP Forums!

  I understand that you're wondering how to scan with your printer HP Deskjet 3050 on Windows 7, and I'm happy to help you!

  Please follow the steps in this guide, using full HP software (Windows 7) scanning function.

  For future reference, hereis the User Guide for the your printer.

  I hope this helps!

  "Please click the Thumbs up icon below to thank me for having responded."

• Problems scanning with Photosmart 5510 on Yosemite Mac (OS 10.10)

  I recently spent a MacBook Pro to a MacBook Air Yosemite running. My printer/scanner was perfectly compatible with the old machine, but nothing else that headache has provided on the new.

  The printer actually works OK but the scanner consumed enormous amounts of time to fix it and still does not work.

  I have installed and reinstalled the driver current time more than I can count. Sometimes the HP utility freezes and has to be restarted. Sometimes it just hangs. Sometimes, I have a screen similar to the one below showing that it has connected to the scanner and activated, but when I go to scan, I absolutely zilch.

  Please help me solve this problem. I've posted about it a number of times, sent tech support several times and I wrote to the head of the tech group. I got response ZERO in five days and am almost ready to ban all products HP to my office to go always.

  

  Hi there @HVDesigner , welcome in the community

  I hope to be useful for the problems of scanning that you face with your new MacBook Air, Yosemite running. Before attempting any software troubleshooting more, I will suggest checking the material, reset the printer and the network (if you are connected).

  1 reset the printer, and then make sure that the printer is plugged directly into the wall, avoiding bars power and surge protectors. This ensures that the printer is full on and can help analyze. I was witness to a direct connection, only this type of fixing problem.

  Press the power button to turn the product on.
  With the product, unplug the power cord from the back of the product.
  Unplug the power cord from the wall outlet.
  Wait at least 15 seconds.
  Plug the power cord into the wall outlet.
  Reconnect the power cord to the back of the product.
  If the product does not light by itself, press the Power button to turn it on.

  2. try power cycling network devices:
  Turn off the printer and the computer and unplug the router for 1 minute (do not press the buttons on the router).
  Plug the router back in and wait another minute, turn on the printer and the computer.

  3. a copy to make sure that the printer is in good working condition to continue software troubleshooting.

  4. If copies of work without a problem, try the following steps in order:

  1. Mac OS X: how to reset the printing system
  2. Repair disk permissions
  3. Restart the Mac.
  4. Download and install the complete driver here: printer e-all-in-one HP Photosmart 5510d printer B111h/B111j full feature software and drivers
  5. In addition, to download this driver: HP v3.0 for OS X printer drivers

  5. try scanning with scans and software scanning HP should work now!

  If by chance the scans do not work, please, give us a call.

  Please contact our technical support at the 800-474-6836. If you do not live in the United States / Canada region, please click the link below to get help from your region number. http://WWW8.HP.com/us/en/contact-HP/WW-phone-assist.html

  Have a great Monday!

• Major problems in scanning with c410a all-in-one...

  In courses run a Windows 8.1 high-end desktop system with a huge amount of memory and have experienced a tremendous amount of problems printing & scanning with my c410a. I have run the maintenance on this pc daily cleaning Cache, Virus scan, all and then some, the PC is a horse race except for printing and scanning...

  This Scanner/printer works very slowly, more slowly, and then it did on my old XP system for 10 years.

  Sometimes in the middle of the analysis, it stops and freezes by me to close the centre of solutions through the Manager of task or at best its not scan more then 2 or 3 elements software b4 of the scanner hangs. I tried everything in the forums I've seen, unplug the power cord of the c410a, restart, etc... Everything that...

  I ran the "HP Print and Scan Doctor" and sometimes it seems to work, allowing me to sweep slowly a point or two b4 it crashes again. Howeverwhen running the Scan Doctor it especially crashes when it gets to the part "scan Windows wia" of its efforts. These poor printing and scanning capabilities on the PC or faster (a factor) that I've ever used is unacceptable.

  Surely you experts can troubleshoot a very frustrated guy from HP?

  Thank you all for your help, especially the HP Tech Support staff... Although I just bought a laptop $1100.00 at HP with a support package for Smartfriend Tech that I don't try to use it for this problem because this c410 is on my desk which is not an HP.  Just for the record I never got my HP HP mini work said they could fix it by phone, but wanted at least $60.00 $ to do. I never had luck with my HP stuff, but I hope that this will not be the case with my new HP laptop... I had heard that HP had better...

  The problem with my c410a seems to be resolved and I can make the dpi / send changes in 10 seconds approximately. Slow but manageable compared to the 3-30 minutes, he took earlier today.  How I solved it on my own without ANY HP

  Support Tech or HP Forum was to completely delete all HP software from my desktop system and installation of the HP Wizard and to install All THE OF BLOATWARE ITS on my system. I had previously been excluding the HP Photo creations, Bing toolbar and software HP Customer Participation however magically or predictable when I allowed all of HP's Bloatware to be installed it worked the works. With the exception of the Bing toolbar that I got an error for which says it's not compatible with IE 11, it's funny I think.

  Only, I posted this comment on the risk that it may help other people having the same problem as it may seem, with HP, you have a better chance to get help from people who are not HP or only if you pay HP to help. While I would expect HP to delete this message who knows maybe they figure this is the best message in the month.

• Cannot scan with Photosmart C6280 with Mac OS x Snow Leopard.

  When I try to scan with my Mac, I get a scanner not found error.  I am able to print.  When I access the HP utility, it shows the printer in the installed column but it shows a Red House beside her and will not let me access it. The printer is connected to an Apple Airport Extreme, via an ethernet cable, and the airport is linked via a USB cable to the computer.

  I guess you mean that the printer and the Mac are connected to the router with Ethernet Airport?

  If you are using snow leopard and have the HP software before Snow Leopard (either from a CD not marked as compatible with 10.6 or you recently upgraded to Snow Leopard and had the software HP on your Mac before you upgrade - even if you made a standard from the old software uninstaller or installed new software on top of it) , you must uninstall the software using the "scrubber":

  Go to Applications/Hewlett Packard / click Uninstall HP
  Click on continue
  Highlight your device in the left pane
  Hold down the Ctrl and Opt Cmd and click on uninstall< scrubber="">
  There will be a pop up that asks if you are sure you want to uninstall all hp software. (At this point, if you continue, all HP printers you have installed will need to be reinstalled)
  Click on continue and let it finish

  Restart your Mac

  Now run a software update.

  Finally, download and install the "Full Featured" driver and software from the "Support & drivers" link at the top of this page.

• Please scan my old facebook lisa sally simpson liza simpson simpson liza mary simpson please

  I need u scan my old facebook of sally lisa simpson 3 diferent pictures liza simpson 3 diferent pict mary simpson lisa simpson 1 diferent picture mary diferent simpson photo 1 photo 1 scan facebook

  my new facebook is jenny simpson * address email is removed from the privacy * 

  Microsoft who run this forum does not own or operate FaceBook. Nobody here can then make any changes to your FaceBook accounts for you. You will have to either do it yourself or with the help of Facebook support.

• Not able to scan with the preview after upgrade from Mac OS Sierra...

  After upgrading to Mac OS Sierra. I'm unable to use the preview to scan.  Before this upgrade, it worked fine.  The HP scanner software does NOT work something like OS 10.8 or 10.9.  Preview worked perfectly so far.  If anyone knows how to solve this problem, your contribution will be greatly appreciated.  Thanks in advance.

  Have you tried scanning with Capture of Image instead? It worked for me.

• Hi all, I keep is typed in the password at startup box, in bars in safari and firefox coupled with a stuck key noise that stops when you press a key, I scanned with antivirus that seems clear, can anyone help?

  Hi all, I get a storm of +'s typed in the password at startup box upward, in bars in safari and firefox coupled with a stuck key noise that stops when you press a key, I scanned with antivirus that seems clear, can anyone help?

  Clings in the key on the keyboard? Wired or wireless keyboard?

  Try to run this program, copy and paste the result in a response. The program was created by Etresoft, a regular contributor.  Use please copy and paste the screenshots can be difficult to read. On the screen with the Options, please open Options and tick the boxes in the bottom 2 before the race. Click on the button "Report share" in the toolbar, select "Copy to Clipboard" and then paste into a response. This will show what is running on your computer. No personal information is shown.

  Etrecheck - Information System

  Reset an Apple Bluetooth mouse or Trackpad wireless keyboard (pairings and other common troubleshooting problems)

  Restart your computer, hold down the option/alt - P - R keys command before the gray screen appears. Continue until you hear the startup chime for the second time.

  Reset the NVRAM EXTRA memory

• How can implement you not with Tim Capsule and AirPort their simulation on the iMac?

  Hello

  How can implement you not with Time Capsule and AirPort their simulation on the iMac?

  I don't know what you're asking.

  AirPort Extreme is a wireless router.

  A Time Capsule airport is an AirPort Extreme with a built-in hard drive for data storage.

  An iMac is a Mac computer.

  An iMac is not a wireless router, so he is unable to perform the functions of a wireless router.

• After the update to firefox 17.0 when I do a scan with Norton 360 it does not pick up the tracking cookies which changed 16.0.02

  After the update to firefox 17.0 when I do a scan with Norton 360, it is no longer captures the rejected. These cookies that have been picked up with firefox 16.0.02 what you have changed? Plus, I'm getting sick of these updates - at least we tell users what has changed in new versions.

  First of all, we do not say what has changed in each version, http://www.mozilla.org/en-US/firefox/17.0/releasenotes/.

  Secondly, Norton should always be able to delete your cookies (just so that you know that the cookies are generally harmless, and you don't need to worry to remove). If not, you can delete the cookies in Firefox Cookies - Information that Web sites store on your computer

• Adafruit.app shows only a white screen with old BONES, 21/03/16 OS. Clues?

  Adafruit.app if only white poster with old and new tvOS updated 21/03/16 OS 9.2 on Apple TV. Deleted Adafruit and re-installed. No change. All other applications work fine: Netflix, Apple, movies, etc, etc...

  Clues?

  Same problem for me too. Can be useful to reach out to the developer of the application.

• Microsoft Surface Pro3: implementation of scan wireless

  I have a printer HP Laser Jet professional M1217 MFP nfw perfectly print wireless.  When I try to set up the "scan document" and looking for my scannoer (printer) it can't find the printer.  I used for the IP address of the printer and it does not always find.

  Please specify,

  HP and Capture scanning does not support your printer as listed in the following document:

  http://support.HP.com/us-en/document/c03489433

  Of the control panel go to devices and printers, remove any existing M1217 Laserjet device.

  Then download and install the HP software full functionality, then scan using HP ScanTo program:

  http://ftp.HP.com/pub/softlib/software12/COL32629/im-80811-7/LJM1130_M1210_MFP_Full_Solution.exe

  As reference, see the following document on scanning with the printer on Windows 10:

  http://support.HP.com/us-en/product/HP-LaserJet-M1200-multifunction-printer-series/4292048/model/4075471/document/c04728884/

  Shlomi

• Can't scan with HP LaserJet MFP M127fw Pro

  I have installed the printer driver and tried to follow the instructions in the manual to scan a document.  When I find my printer folder in the start menu/all programs, there is no option to scan. Help!

  Hi @3Digit .

  I see that you are having problems of analysis, it is not any scanner in the HP folder software. I would like to help you today.

  Open the HP scanning with one of the following methods: