Import failed halfway, how to synchronize the folder to import the remaining images?

Similar Questions

• How to synchronize the start of IT and relaxation the Scan list (DAQmx Switch)

  Hello

  I want to measure samples of N to the AI0 of Council NI PXI 4461. The measurement starts on a rising edge of a digital triggering provided to the PFI0 of the same Board. The measure is configured with samples of N/2 pretrigged. So far, everything is under control...

  Using an NI PXI 2567 Board, the signal applied at the entrance the 4461 (AI0) switches between a V2 and V1 signal. I would like to synchronize the switch between the two signals with the trigger signal applied to the input of the PFI0 Governing Council 4461. In order to obtain samples of N/2 of V1 and V2 samples N/2. Synchronization of 1 to 5 ms would suffice!

  My question is how to synchronize the start of acquisition of AI pretrigged of 4461 with the switch control given by the Council of 2567?

  Thank you in advance for your help...

  PS: the configuration of the system is:

  -LabView 8.5

  -Chassis PXI-1044

  PXI-4461 on slot 2

  Module 4-slot PXI-2567

  Hi Frederic,.

  I came back to this recently and used the following examples to run the desired synchronization.

  PXI-4461: Acq & graph tension-Int Clk - dig Start & Ref .vi

  Samples per channel = 1000

  Rate (Hz) = 10000.00

  Start the trigger Source = / [name of the instrument DAQmx] / PXI_Trig0

  Onboard start = fall

  Reference Source Trigger = DAQmx Device Name] / PXI_Trig0

  Reference edge = fall

  Trigger samples = Variable (100, 500, 900)

  PXI-2567: Switch Scaning-SW Trigger.vi

  Advance the output terminal full = / [name of the instrument DAQmx] / PXI_Trig0

  Scan list = / [name of the instrument DAQmx] / ch0-> com0.

  Scan list = / [name of the instrument DAQmx] / ch1-> com1;

  Hardware configuration:

  The PXI-2567 module controls an external relay that switches between the voltage of 5 V on ch0 and ch1 0 V.

  The PXI-4461 connects to the COM of the external relay and therefore reads 5V when ch0 is connected; 0 v when ch1 is connected.

  Procedure: The above examples are used in the following procedure.

  1. run the PXI-4461 VI.  A start trigger (falling edge) is necessary to start collecting samples before firing.

  2. launch the module, PXI - 2567 VI.  When ch0 is initially (and immediately) on com0, a trigger is sent to PXI_Trig0.  The PXI-4461 will begin to acquire samples before firing.

  3. - click on the "Connect to the next" button on the front of the PXI - 2567 VI module.  This sends a trigger to entry software for the PXI-2567 module and the transitions of the scan for ch1-> com1 list.  Once the PXI-2567 module remains (debounced), advanced complete relaxation is sent on PXI_Trig0 for the PXI-4461.  The PXI-4461 will begin to acquire samples after outbreak.

  Note: Instead of the trigger of the software entry, an external input trigger can be used (e.g. PXI_Trig1).

  Results:

  > Before instant release of samples = 100

  Delay is caused by the time of actuation of external relay.

  

  > Before instant release of samples = 500

  Delay is caused by the time of actuation of external relay.

  

  > Before instant release of samples = 900

  Delay is caused by the time of actuation of external relay.

  

  I hope that the attached screws and the explanation above helps you and/or other customers who have this problem.

  Best regards

  Chad Erickson

  Switch Product Support Engineer

  NOR - USA

• How to synchronize the start time in the waveform graph

  Hi all

  I just find a solution in the forum to select the data you want in a grap of waveform with cursors, however, I don't know how to synchronize the time of beginning of waveform for the second graph. How can I extract start time of the waveform with the index data?

  

  Something like that?  It is a bit gross, but is what I think you're asking, should be able to use it as a starting point.

  

  The Max - Min is to make sure that the cursor is always valid.

• HOW TO SYNCHRONIZE THE MONSTER AND THE CAMERA?

  I'M TRYING TO WORK WITH CHARACTER ANIMATION. I CHOSE THE MONSTER. I SEE MYSELF ON HER CANERA, I PUT RESET POSE AND THE MONSTER DO NOT MOVE WITH MY MOVEMENTS. HOW TO SYNCHRONIZE THE MONSTER AND THE CAMERA? Thank you

  Hi Luz... You have the track selected in the timeline panel puppet? You need to target the puppet that is controlled by the webcam/microphone/keyboard/mouse by selecting its track. That it arms for registration.

• How to set the background image on my request.

  Hi all

  I use jdev 11.1.2.4.0 version

  use case: I create mobile applications and using the skin by default 'mobileFusionFx '.

  so when I run application there show black screen as a background image on my application

  My question is how to change the background image.

  Thank you

  Manish

  Resources of the Application open-> descriptors-> ADF META - INF-> adfmf-config. XML

  Check the family skin it and use in the skin of skin-addition id attribute.

  With this way automatically all your pages will use the same background image.

  In addition, background - image: url("images/back.png");    ---> It denotes that this images folder is inside the css file. If the pictures folder is a brother to css file, use

  background-image: url("..) (' / images/back.png ');

• How to print the specific image size?

  Hi Gang - How can I print an image 11 x 15 "on paper 13 x 19"?  Initially, it seems easy, but things are not how to navigate. Here's what I did:

  I exported the photo and used the dialog box LR image resize to 11 x 15 "- easy."

  I imported the exported image (assuming that the image was 11 x 15 ") and then in the LR print area - it is where the confusion begins.

  The print tab displays the dimensions of the image as 8 x10.19 in.  Help, how can I do the 11 x 15 "I need it to be?

  I understand that I will need to adjust the image to get the part I want in the space of 11 x 15, but for the moment, I can't even 11 x 15 "size.

  I tried package customized options, but no luck there.

  I would like to Print Studio Pro Canon plugin that works very well. Except, again, I don't know how to ask the image size 11 x 15 "for printing on paper 13 x 19".

  Fiddling with settings, I printed a dozen attempts and still no luck to reach 11 x 15 "size of the image on paper 13 x 19".  For now, I'm OK with the image to cut or to another plane - no baby - I need to know how to make the print image 11 x 15 "size of the image. A

  Thank you to offer suggestions.

  Screenshot shows that my image 11 x 15 "is 8x10.19; I don't know how 11 x 15 ".

  

  LR v5.7

  Mac OS X Yosemite v10.10.2

  Brain: generally intuitive, but need some help on this issue!

  The first step in the Lightroom print module is to click on the Page Setup button, select your printer, and then select the paper size. It looks like your screen to paper size correct has not been selected yet, because you said you wanted to print on paper 13 x 19 inches, but the paper on the screen is only 8.5 inches wide. My guess is that Page Setup is always programmed for letter-size paper, and you should come back on layout and change it. After you do this, if your layout Style is unique, you should be able to affect the size of the cell 11 x 15 inches.

• How to mount the iso image on the ESXi Tech support console

  Hi friend

  How to mount the iso image on the ESXi Tech support console?

  I run the sub command and it failed.

  # mount o loop-t iso9660 vmware-esx-drivers-net-be2net_400.2.102.440.0-1vmw.2.17.249663.292682.iso / free

  editing: vmware-esx-drivers-net-be2net_400.2.102.440.0-1vmw.2.17.249663.292682.iso mounting on / open failed: no such device

  ESXi does not provide the option of mounting ISOs. You try to install the driver the driver Async package be2net / ISO. Follow the steps below

  (1) install VCLI
  (2) mount the ISO on the host where you installed vcli
  (3) use vihostupdate to install the driver
  vihostupdate-i b - servername
  He will ask for username and password of your host.

  Thank you
  Nithin

• How to disable the PNG Images

  How to disable the PNG Images?

  PNG is a format for images (compressed) as JPG format. There is no way to disable this format.

  If you have a problem with images on web pages, then you will need to block images from certain domains.

  You can watch the Adblock Plus extension to block specific content.

  • Adblock more: https://addons.mozilla.org/firefox/addon/adblock-plus/

  You must subscribe to a list of filters (for example the EasyList).

  • http://adblockplus.org/en/subscriptions
  • http://adblockplus.org/en/Getting_started

• How to correct the bad image applesynofer.exe

  How to correct the bad image of apples synotifer.exe

  Contact apple.

• How I see the preview image of my PDF documents?

  How I see the preview image of my PDF documents?

  Hi josepm26085232,

  Preview of thumbnails has been disabled in the latest Adobe Acrobat Reader DC due to security problem.

  If you want this feature, you will need to uninstall the latest version & reinstall the old version of the Adobe - Adobe Acrobat Reader DC Distributiondrive.

  Kind regards
  Nicos

• Lightroom displays all images from a folder - it displays the message '45 65 images, selected 45' and 45 messages do not appear in the grid of the library, but I can't see the remaining images of 20. All filters are disabled...

  Lightroom displays all images from a folder - it displays the message '45 65 images, selected 45' and 45 messages do not appear in the grid of the library, but I can't see the remaining images of 20. All filters are disabled...

  Hello

  Please go to the library Module, then click on the picture in the Menu bar and then click the stacking.

  From there please select expand all stack them.

  It should show all the images if they are virtual copies.

  Kind regards

  Tanuj

• How to set the background image in the window title?

  Hello

  I am a beginner in flex. I use Flex 4.

  Can someone give me some advice on how to set the background image in the title window?

  Is it possible to do?

  Thank you.

  Hello

  Check the code in the example below

  
  http://ns.Adobe.com/MXML/2009.
  xmlns:s = "library://ns.adobe.com/flex/spark".
  xmlns:MX = "library://ns.adobe.com/flex/mx" minWidth = "955" = "600" minHeight >
     
         
     
     
  @namespace s "library://ns.adobe.com/flex/spark";
  @namespace mx "library://ns.adobe.com/flex/mx";

  s | {BorderContainer
  background - image: embed(source="image/wheres_the_green_rez.jpg");
  background-image-fill-mode: clip;
  }

  
     
         
     
  

  Kind regards

  Anitha

• How to synchronize the folder on the PC with folder on a flash drive.

  I would like to be able to synchronize a folder on my USB key with a folder on my PC. Is it possible to do? Basically, I'd love to plug my USB key, right click on a folder and synchronize it with my PC.

  Thank you

  Like Steve, I use the second copy. I also use SyncToy or Rich Copy depending on the situation. You can also check the Win 7 Sync Center facilities. All of these solutions offer simple point and click ease you want, but are worth a glance, I think.

  http://TechNet.Microsoft.com/en-us/magazine/2009.04.UtilitySpotlight.aspx?PR=blog
  Center of control Panel\All Control Panel Items\Sync

  Tom

• How to synchronize the metadata of LR to bridge

  Hello. I have W7 64 bit, CS5 with ACR6.1 and LR 2.7. My Leica camera capturing in DNG natively. I use "Convert to DNG" import in order to take advantage of the lossless compression. I understand that the XMP sidecar files are not applicable and that the metadata is written into the header DNG. It's good for me, it should ensure that the metadata is always with my DNG, but I'm not sure how it affects the validity of any instructions, I found so far.

  Currently I use ACR and LR to develop files to take advantage of the new features and treatment until I can get LR3.

  I want to synchronize the development parameters. I learned to updated the metadata of files developed in ACR6.1 when I open them in LR2.7 but I can not work, how do the LR develop visible settings when I open the files in Bridge.

  Any suggestions would be greatly appreciated. I was unable to find the information in the forums or help so far.

  I'm also not sure if this is the best forum to post this, but he did not cross the. If I am better publish it on another forum, please excuse me and suggestions would be welcome.

  If you want a set folder to update faster, go to tools/cache/purge cache for folder xxx.  Let the inch rebuild foremost (in corner he'S spinning arrow).

• How to synchronize the device with an analog input device?

  Is it possible to synchronize a device (e.g. Basler scA640-70fm, IEEE 1394 b or NI 1722 smart camera) with an input device analog (for example, NI PCI/USB-6225 or NI PCI/USB-6255)?   For example, it is important to a video image of match with a sample of data digitized by the A/D converter.   In particular, it is important to know when the first video image starts compared to samples of digital data.   If it is possible to synchronize the camera with the A/D device, then then how is it?

  Thank you

  Ian

  Hello Robert,.

  Thank you for reference and information.

  Ian