Impossible to establish a correlation between the Script

Similar Questions

• I am able to connect to the internet with internet explorer, but when I try to connect through mozilla firefox it says "it is impossible to establish a connection with the server." why? "

  I can establish an internet connection via internet explore using a router at home, but whenever I try to connect using firefox, it said that it is impossible to connect.

  One possible cause is security software (firewall) that blocks or limits Firefox without you informing on this subject, possibly after the detection of changes (update) for the Firefox program.

  Delete all rules for Firefox in the list of permissions in the firewall and leave your firewall again ask permission to get full unlimited access to the internet for Firefox and the plugin-container.

  See Server not found - the problems of connection and Configure the firewall so that Firefox can access the Internet and http://kb.mozillazine.org/Firewalls

• Impossible to establish a VPN between AG241 and WAG54GP2 tunnel

  Hello

  This is my first post on this forum and I send my best regards to everyone!

  I signed up because I have a problem with establishing a VPN tunnel between an AG241 modem/router and a modem/router WAG54GP2 with wireless and VoIP.

  The scenario is simple: both ends have dynamic IP, so I set up an account with dyndns.org for both routers.

  WAG54GP2 has 192.168.1.1/255.255.255.0 AG241 has 192.168.3.254/255.255.255.0 IP and IP.

  In both routers, I turned block anonymous internet requests, so I can ping both routers.

  This is the configuration of WAG54GP2:

  VPN Passthrough
  IPSec PassThrough: activate
  Intercommunication PPPoE: activate
  PPTP PassThrough: enable
  L2TP PassThrough: enable

  IPSec VPN tunnel
  Select the Tunnel: 1
  VPN IPSec tunnel: enabled
  Tunnel name: Office

  Local security group:
  Subnet
  IP: 192.168.1.0
  Mask: 255.255.255.0

  Local security gateway: PVC 1 (ppp0)

  Remote secure group:
  IP: 192.168.3.0
  Mask: 255.255.255.0

  Remote security gateway:
  IP Addr.
  The remote router's public IP address IP address: w.x.y.z.
  Encryption: THE (I also tried 3DES and disabled)
  Authentication: SHA

  Key management:
  Auto. (IKE)
  PFS: enabled
  Pre-shared Key: the password I chose
  Life key: 3600 Sec.

  Advanced settings

  Phase 1
  Mode of operation: main mode (I also tried aggressive mode)

  Proposal1
  Encryption: A
  Authentication: SHA
  Group: 768 bits
  Life key: 3600 sec.

  Proposition2
  Encryption: ESP_NULL
  Authentication: SHA
  Group: 768 bits
  Life key: 3600 sec.

  Another parameter
  NAT traversal not verified
  NetBIOS broadcast Checked
  Anti-reponse not checked
  Keep-Alive not verified
  If IKE 5 times failedmore
  Not checked

  This is the AG241 configuration:

  VPN Passthrough
  IPSec PassThrough: activate
  Intercommunication PPPoE: activate
  PPTP PassThrough: enable
  L2TP PassThrough: enable

  IPSec VPN tunnel
  Select the Tunnel: 1
  VPN IPSec tunnel: enabled
  Name of the tunnel: user 1

  Local security group:
  Subnet
  IP: 192.168.3.0
  Mask: 255.255.255.0

  Local security gateway: PVC 1 (ppp0)

  Remote secure group:
  IP: 192.168.1.0
  Mask: 255.255.255.0

  Remote security gateway:
  Any

  Key management:
  Auto. (IKE)
  PFS: enabled
  Pre-shared Key: the same password I put on the WAG54GP2
  Life key: 3600 Sec.

  Advanced settings

  Phase 1
  Mode of operation: main mode (I also tried aggressive mode)

  Proposal1
  Encryption: A
  Authentication: SHA
  Group: 768 bits
  Life key: 3600 sec.

  Proposition2
  Encryption: A
  Authentication: SHA
  Group: 768 bits
  Life key: 3600 sec.

  Another parameter
  NAT traversal not verified
  NetBIOS broadcast Checked
  Anti-reponse not checked
  Keep-Alive not verified
  If IKE 5 times failedmore
  Not checked

  When I click on Connect the WAG54GP2 router, do not access and in the newspapers, I see:

  2009 07-30 T 16: 16:10 + 01:00 IKE ["Board"] Tx > MM_I1: SA w.x.y.z.

  2009 07-30 T 16: 16:20 + 01:00 IKE ["Board"] ERROR: message w.x.y.z. port 500: connection refused

  If I use the dynamic FQDN instead of the dynamic IP (w.x.y.z.) change of message for:

  2009 07-30 T 16: 46:16 + 01:00 IKE ["Board"] ERROR: problem of remote domain name Security Gateway!

  Is there someone who could help me build this tunnel?

  A big thank you to everyone who will help me!

  Cinghiuz

  If you are Encountering difficulties connecting to the VPN Tunnel using a router ADSL modem you should see this

  Also, make sure that you have the latest firmware installed on your entry door and change the MTU setting...

• Impossible to establish a connection between microsoft router, modem, motorola and dell/windows xp computer

  I have not set up a connection between my computer dell/windows XP, Microsoft router and my Motorola modem. After reading the instructions for the router and set up like it says anything I've set up my computer say it is connected but is not really plugged. My ipod says that there is this WiFi but when I try to access the internet on it, it gives me a message saying "unable to connect to the internet, there no connection detected." The only time where I have Internet on my computer is when I unplug the Ethernet to the router and modem and have the modem only connected to one computer. This problem is can cause because my modem is configured with a cable from cox and not connected to a phone cord? (My router is a Microsoft Broadband networking Base station wireless MODEL: MN-500) (My modem is a modem cable Motorola surfboard implemented with internet helmsman) (My computer a DELL Dimension E521 with a windows XP service pack)

  SP3 is on it? Wireless is enabled on the router? Try this

• Connection between the script and view

  I was seen by default budget should be periodic, and real for a YEAR. How to interpret it?

  Usually you specify the view anyway, so by default has no effect.  For example, "data extract" periodic offer / CDA / default scenario as three options.

  Are you sure that the person saying "Default View... "talked about the dimension of the view? Budget reports are most often (by default) presented as periodical data more 'Total year' and perhaps quarterly or semi-annual subtotals.  Actual expenditures appear more often for a YEAR.  Actual expenditures and Budget are compared, it is common to have six columns: three for the month underway (i.e. recurring) Budget / actual / Variance and three others for CDA Budget / real / Variance.

  Your question has been here a while unanswered so far.  I think maybe it's because the question can be understood in different ways and people don't want to waste time answering the wrong interpretation.

• Correlation between the cpu load and the queue

  We are seeing cases where our CPU usage is less than 50%, but we babysit run queues of more than 10 minutes. I expect a large queue if we were see a greater use of the CPU, but I'm unable to correlate a large queue with low CPU usage. Has anyone else seen a condition like this or have any ideas. Database is 11g RAC Exadata X 2 full rack. We use the ORM to manage the resources of the processor as well.

  It is an informative read: http://shallahamer-orapub.blogspot.com/2010/07/os-cpu-run-queue-not-what-it-appears.html

• Question on 'between' the use of mapping

  Hello
  
  I use FDM to load data in Hyperion Planning (all in 11.1.2)
  
  I want to define a mapping rule that says:
  All my agency with a code between 100 and 600 have been uploaded on the entities with the sames codes in Hyperion.
  
  Is this possible with a card?
  I tried:
  100 600 = > *.
  and
  100 600 = > 100 600
  but it does not :-(
  
  Or do I have to use cards with something like this:
  1? = > 1?
  2? = > 2?
  3? = > 3?
  4? = > 4?
  5? = > 5?
  600 = > 600
  
  Thank you in advance for your help!
  
  Fanny

  I never did flow through the mapping on a map between, but I would have thought that the wildcard would work. Because that doesn't work for you, try to set the principal target in your original between the '#SCRIPT' card and set the Script field on "result = varValues (15).

• geometric matching: difference between the scores and correlation

  Hi all

  What is the difference between the scores and correlation in geometric correspondence?

  Hello

  the correlation score is based on pixel intensities while the score of the geometric game also considers the characteristics of the geometry. See the Concepts of Vision or (geometric matching-> discussion).

  I hope this helps.

  Best regards

  K

• How to establish the relationship between the tables contact and Global (entity) in Oracle Service Cloud to preconfigure data

  Hello

  We strive to integrate the OPA attributes to the Cloud Service Oracle tables to store session data for the customer portal users.

  We tried mapping the attributes of the OPA with relevant tables of cloud Service Oracle? Is there any installation of additional data to create to retrieve the session data for the particular user / contact?

  We managed to save tha data in arrays of cloud Service for users of ananymous and also well regarding customers portal users but to preconfigure data do we need to do any additional configuration / mapping to the contact table?

  Please help on the establishment of the relationship between the contact and Global (new table created in cloud Service) tables.

  Thank you

  Vivek

  Hi Vivek,

  To load data from the Contact in the the OPA policy template, you must configure the widget of the OPA. For instructions, see the following articles:

  - Incorporate an interview that uses data portals in Oracle Service Cloud Customer Portal

  - Deploy and configure the sample OPA widget

  - Insert the widget to sample in a customer portal page

  Obviously, you need to do the mapping in OPM as well, but even if the mapping is correct, you will not be able to load the Contact data unless the widget of the OPA is implemented.

  See you soon,.

  Jasmine

• How to use between operator in Disqualification without using the script processor?

  Hello Experts,

  How to use between operator in Disqualification? for example phonenumberLength between 7 and 10. I don't want to use the script processor? Also how to reproduce the SWITCH statement Disqualification CASE?

  Thank you

  Konate

  1 Add a processor 'check the length.

  2. connect the transformer and open the configuration dialog box

  3. in the tab 'Attributes' select your attribute of telephone number as the "field Check.

  4. in the tab "Options", enter "7-15"in the option 'number of valid characters.

  5. run the process.

  a. accounts with [included] a character length 7-15 phone numbers out of the release of "valid".

  b. records with a length of character <7 or="">15 phone numbers out of the release of "Invalid character count.

  Note: the processor also adds a 'LengthValid' flag attribute which you may also branch on [with the values "Y" and "NC" for both scenarios above]. See Library of processor of the online help for more information.

  Thank you

  Nick

• Spend the MATLAB data types 'cell' between MATLAB script nodes in LabView?

  Hi all

  I need to pass a variable of data type of cell of a MATLAB script node in LabView to another, but the cell is not listed as a data type 'exit' in the script node.

  Is it possible to do without converting them into a 2D array?  Each column of my cell has a different number of lines...

  Thank you!

  Mike

  Too bad...

  Rather than use a typical LabView, I just say

  assignin ('basic', ' varname', varvalue ");

  in the first script and varname called from the second node to get my cell.

  Easy... duh leaving here if anyone has the same issue in the future.

• NIC impossible printer in Windows 7 Via VB script in the Windows 2003 domain controller

  I have been using the following script to add printers to network shared for users.

  The script worked great with XP machines but on Windows 7, the printers are not map.

  The dose of script to be run, the UAC is disabled on windows computers 7

  The script I use is:

  ' Printers.vbs - Windows Logon Script.

  Set objNetwork = CreateObject

  objNetwork.AddWindowsPrinterConnection "name\printer name".

  objNetwork.AddWindowsPrinterConnection "name\printer name".

  objNetwork.AddWindowsPrinterConnection "name\printer name".

  Any help would be appricated.

  Thansks

  Hi Juliet,

  Thanks for posting your question in the Microsoft Community.

   

  The question you posted would be better suited in the TechNet Forums.

  I would recommend posting your query from the link:

   

  http://social.technet.Microsoft.com/forums/scriptcenter/en-us/home

  I hope that the information above helps you.

• What is the difference between the output of the Script and the result of the query?

  Hello gurus,
  
  In Oracle SQL Developer, during the execution of a select statement running with the "F5 key", I get the output of the Script; And then if I execute the same select statement using 'Ctrl + Enter', I get basically the same data, but it is formatted to be a little different. and using 'Ctrl + Enter' I can adjust and reduce the size of the column (not the logical and physical structure) on the GUI screen to display all columns without having wide apart. What are the advantages/disadvantages to running queries using "F5" or "Ctrl + Enter"? If someone could shed some light on this topic bit, that would be nice.

  HI HAS LUNS,

  Text (f5) is functional, for the better or for the worst dumps select all.
  Chart is prettier - you get a complete data by select grid and scroll within the grid.
  There are a few other minor differences.

  Personally, I use mostly f5 /text/ (sqlplus emulation).

  -Turloch
  Team SQLDeveloper

• What are the relationships between the logging and IKM?

  What is the best method to use in the following scenario:
  I have about 20 tables with the large amount of data sources.
  I need to create interfaces that join the source tables in target tables.
  The tables are inserted every few seconds with about hundreds of thousands lines.
  There may be a gap of a few seconds between the insertion of different tables that could be attached.
  The source and target tables are on the same Oracle instance and schema.
  I want to understand the role of: 'Logging CDC' and "IKM - incremental" and
  How can I use it in my script?
  In general, what are the relationships between "Logging" and 'IKM '?
  Use both? Or maybe it's better deelte and insert the target tables?
  
  I want to understand what is the role of "Logging CDC"?
  Can 'IKM - incremental' work without "logging"?
  Must 'Logging' have PK on the tables?
  What should I do if I can't say PK (there may be several identical lines)?
  
  Yael thanks in advance

  user604062 wrote:
  Hello
  Thanks for your quick response!

  No probs - its still fresh in memory I did a major project on this topic last year (400 tables, millions of lines per day (inserts, updates, deletes), sup-5 minute latency). The problem is it isn't that well written on the web, that you have read the blog of the example I linked to in my first answer? See also here: http://odiexperts.com/changed-data-capture-cdc/

  Always on logging:
  My source table is inserted all the time.
  The interface to join the source table in the target table.

  In ODI, the correct term would be your source table "fits" in the table target, unless you mean literally that want to join the the source with the taget table table? My question if you want to do with the result of the join?

  What exactly the "journaling" CDC updates?
  It updates the model of ODI? interfaces? The source of data in the model of ODI? The target table?

  Logging CDC configures and deploys the data capture mechanism (Triggers or log based capture, IE Logminer/streams/Goldengate) - it is not updated the model as such, she pointed out the metadata of the model of ODI repositoty as a CDC data store, allowing you, the developer say ODI to use log data if you wish (reported in the interface) There is no change in the target table, you get an indicator of metadata (IND_UPD) against a line during the integration (in C$ and I have tables$) that tells you if its insertion (I) and update (U) or deletion (D). It had ' lines allow you to synchronize the deletions, but yoy say its inserts only then you probably used use this option. "
  So the only changes are the source table to your interface, another diary data (if you use logging) or the table of the actual source (if not using the logging).

  This is the main thing that I don't understand!

  I hope I made a little clearer.

  Try the following as a quick test:

  Reverse a source table an engineer and the target (at least) table.
  Import the update incremental LKM and IKM.
  Import of the JKM you want to use.

  Create an interface between the source and the target without any deployed JKM.
  Configure the options of JKM on the model, the "Start log" to start the process of capture - this is quite a complex stage and a lot of things to understand what is happening in the source database, better to check code ODI sends to the database and to review the documentation of Oracle database for a description of what his weight (instantiate Tables (, sets of creating change, creation of subscribers etc. establishment of newspaper groups, creating views Journalising etc.) -you will need to consult your Source DBA database initially as ODI wants to make many changes to the source DB (in mode Archivelog process max, parallelism, size, Java etc.)

  Now, edit your interface and mark the table source for use "Journalized data bank.
  Restart your interface
  Compare the difference in the generated code in the journal of the operator, see the differences of the operator.

  >

  Thank you, Yael

• TypeError: try to run the script compilation and go on a 'mistake' in scope cleared when message returns the transfer through images for each image. Does not affect viewing.

  TypeError: try to run the script compilation and go on a contour

  Above the error message appears when moving between images - back and forth. By clicking on the OK button removes the error message and there is no apparent problem. The window that appears refers to a JAVA Script Application (I guess that FIREFOX is the application?)

  -> Troubleshooting extensions, themes and problems of hardware acceleration to resolve common Firefox problems

  Check and tell if its working.