Impossible to find the field read and write VI in labview 2009

Similar Questions

• Impossible to find more older .vi CAN - 2.0 in labview 2009

  Hello

  I am using a 1 card PCMCIA-CAN/2 series (old enough) in Labview 2009.

  I installed the latest NI-CAN driver that supports this old card (NI-CAN 2.0, I think), but I don't see the can.llb s vi in the functions palette.  The CAN - 2.0 documentation says that it supports versions of Labview "6.1 and later.

  LabVIEW 2009 support this driver?  How to CAN - 2.0 vi appears in the function palette?

  Thank you

  Phil (labview newbie)

  I found the relevant .vi "Labview 6.1/vi.lib" folder of the directory "National Instruments".

  I was looking for the vi now appear in the function palette addons section.

  Thank you

  Phil

• GPIB read and write commands of Agilent 54642 oscilloscope

  Dear friends,

  I would like to acquire a waveform of Agilent 54642 ocsilloscope in the LabView 7.1 via GPIB program. Can anyone mention the GPIB read and write commands for the oscilloscope even?

  Furthermore, on the subject of the LabView program, is it fair to place blocks to write two GPIB followed by a single GPIB read block (everything series), as well as an indicator, in order to check the waveform in LabView?

  Kindly help me with your answers...

  Look forward to y...

  Thank you very much in advance...

  Marion

  Download the 7.0 driver that Albert gave the link to, make sure that you have installed NI-VISA and run the getting started sample which is part of the pilot. If it does not, please elaborate on the error codes that are reported.

• How to read and write attributes using the API?

  I'm trying attributes of access (read and write) of the following:

  SequenceFile

  Sequence

  The sequence steps

  When you look at the documentation of the API, TestStand, the following functions are available:

  PropertyObject

  Properties

  Attributes (read-only)

  HasAttributes (read-only)

  Methods

  DisplayAttributesDialog

  I tried to use the SetValString and GetValString commands using the reference of the attributes, but it does not seem that the data is stored in the file.

  I can't find the following information in the TestStand API:

  1. Where the attributes are stored in a property object?
  
  
  2. How can we access through the API?

  No advice and no information is appreciated!

  You must increment the number of changes to the file after that editing the sequence editor (or UI) won't refresh or mark the file, as amended. Use sequenceFile.AsPropertyObjectFile (). IncChangeCount().

  SequenceFile attributes are stored in the SequenceFile.Data, not the object of SequenceFile object. You can change them in the Advanced tab of the properties of the file sequence dialog box.

  Hope this helps,

  -Doug

• global variable functional to read and write data from and to the parallel loops

  Hello!

  Here is the following situation: I have 3 parallel while loops. I have the fire at the same time. The first loop reads the data from GPIB instruments. Second readers PID powered analog output card (software waveform static timed, cc. Update 3 seconds interval) with DAQmx features. The third argument stores the data in the case of certain conditions to the PDM file.

  I create a functional global variable (FGV) with write and read options containing the measured data (30 double CC in cluster). So when I get a new reading of the GPIB loop, I put the new values in the FGV.

  In parallel loops, I read the FGV when necessary. I know that, I just create a race condition, because when one of the loops reads or writes data in the FGV, no other loops can access, while they hold their race until the loop of winner completed his reading or writing on it.

  In my case, it is not a problem of losing data measured, and also a few short drapes in some loops are okey. (data measured, including the temperature values, used in the loop of PID and the loop to save file, the system also has constants for a significant period, is not a problem if the PID loop reads sometimes on values previous to the FGV in case if he won the race)

  What is a "barbarian way" to make such a code? (later, I want to give a good GUI to my code, so probably I would have to use some sort of event management,...)

  If you recommend something more elegant, please give me some links where I can learn more.

  I started to read and learn to try to expand my little knowledge in LabView, but to me, it seems I can find examples really pro and documents (http://expressionflow.com/2007/10/01/labview-queued-state-machine-architecture/ , http://forums.ni.com/t5/LabVIEW/Community-Nugget-2009-03-13-An-Event-based-messageing-framework/m-p/... ) and really simple, but not in the "middle range". This forum and other sources of NEITHER are really good, but I want to swim in a huge "info-ocean", without guidance...

  I'm after course 1 Core and Core 2, do you know that some free educational material that is based on these? (to say something 'intermediary'...)

  Thank you very much!

  I would use queues instead of a FGV in this particular case.

  A driving force that would provide a signal saying that the data is ready, you can change your FGV readme...  And maybe have an array of clusters to hold values more waiting to be read, etc...  Things get complicated...

  A queue however will do nicely.  You may have an understanding of producer/consumer.  You will need to do maybe not this 3rd loop.  If install you a state machine, which has (among other States): wait for the data (that is where the queue is read), writing to a file, disk PID.

  Your state of inactivity would be the "waiting for data".

  The PID is dependent on the data?  Otherwise it must operate its own, and Yes, you may have a loop for it.  Should run at a different rate from the loop reading data, you may have a different queue or other means for transmitting data to this loop.

  Another tip would be to define the State of PID as the default state and check for new data at regular intervals, thus reducing to 2 loops (producer / consumer).  The new data would be shared on the wires using a shift register.

  There are many tricks.  However, I would not recommend using a basic FGV as your solution.  An Action Engine, would be okay if it includes a mechanism to flag what data has been read (ie index, etc) or once the data has been read, it is deleted from the AE. 
  
  
  There are many ways to implement a solution, you just have to pick the right one that will avoid loosing data.
  

• I read and write English but my husband reads and writes in Russian. How can I activate the taskbar of the Russian language?

  My husband is from the Russia.  It reads and writes in Russian and I'm having a problem turning on the Russian keyboard.  I went many steps of the menu start, Control Panel, regional and language options, languages, details.  I added the Russian.  under the Russia, there is a symble of a keyboard than Russian (typewriter) Russia and the United States.  acorrdign at every stage, there should be a tab in the bar of tasks showing that I can switch bewteen eglish and Russian.  who does not come to the top.  I have check the tab bar of language and made sure all the boxes are ticked, but I still can't find the language bar. what I am doing wrong?

  I don't need a translator who is the other thing that I still find.  I need for my husband who bought the computer to be able to type in Russian, his mother tongue.

  Thank you for your time,

  Heather

  See if that helps you

  http://Office.Microsoft.com/en-GB/Outlook-help/switch-between-different-languages-by-using-the-language-bar-HA010362283.aspx

• Read and write data to the content repository.

  Hi all
  We use the content repository to store a document and images on the web server in the Center.
  So we have created/setup a repository of content on the web center.
  Please proivde me some might document page to get an idea of how I can read and write the date
  content repository.
  You are most welocme to provide some idea /suggestion.
  Thank you
  Arun.

  You are using webcenter spaces or you create a custom application webcenter?

  When you create a custom application webcenter, you can make use of the workflow Documents. Jdeveloper resources catalog, you will find a few flows of Documents job that will allow you to add some components to manage documents in a folder structure.
  You must first create a connection to your content from your application server. This can be done in the Application resources, right-click on the connection and in the context menu, select "content repository". Them you must filll in connection to your content server details. Make sure you have selected "Set as primary connection for document service" because otherwise the document taskflows you deposit on your page will not find a connection.

  Once you have added the connection, you will also find a datacontrol to the content repository. In this way, you can use the datacontrol place the taskflow and you can create several custom tables.
  I'm not sure but I think the datacontrol also include surgery to create the document but I'm not sure...

  And if not enough, you can always do use the webservices provided by content server. In Jdeveloper you can easily create a datacontrol from Web services by providing the wsdl file. UCM provides for services so that you can import the wsdl into your application and you can easily create your own forms checkin, tables...

  Here is some information on how to integrate services document:
  http://sqltech.CL/doc/oas11gR1/WebCenter.1111/e10148/jpsdg_doc_lib.htm

  and here are some others:
  http://sqltech.CL/doc/oas11gR1/WebCenter.1111/e10148/jpsdg_content.htm#BABCCFJH
  http://sqltech.CL/doc/oas11gR1/WebCenter.1111/e10149/documents.htm#WCSUG2635
  http://sqltech.CL/doc/oas11gR1/WebCenter.1111/e12405/wcadm_documents.htm#WCADM205

  Published by: Yannick Ongena on Oct 8, 2010 08:23

• Using the same interface CAN read and write

  Hello.

  Can I use the same CAN interface to read and write?

  For example:

  I send you CAN frame using CAN1 to my MCU.

  IF MCU confirmed the order of receiver it immediately sends the echo return command and there different ID to send the command.

  I tried to use CAN1 output framework and then reconfigures CAN1 to frame in queue and retrieve the frame of the echo.

  But it seems that I was always missing. The 'framework of CAN' kept vi expire.

  When I used the separator on the outlet BOX in my configured MCU CAN1 for frame and CAN2 for chassis in and I managed to catch the echo framework.

  I think about 100 ms for the frame in response that will be sent after the order has been received. It takes longer for the NI PXI-8513 reconfigure? Can I still do it, or I have to use the separator?

  I wad jump to use an interface to read and write.

  Thank you

  Ok. I misread your notion of echo. I understand now. I'm sorry.  The code you posted seems reasonable.

  (1) did you notice on or off for the session?

  (2) what baud rate? You can add a parameter of baud rates for the property to be explicit node.

  (3) I don't remember the name of VI, but you can add a status of Comm Get after reading. This will give you some information about the bus - if errors were detected, etc. Which can be useful to help debug.

• TCP Read and Write at the same time

  Hello everyone,

  I have a question about parallelism in TCP connections.

  I know that it is possible to read and write on the same connection ID.

  So, if you ReadTCP and WriteTCP block each other, if you use the same TCP connection ID?

  Or to request more precise if I run two while loops, in parallel, with one end by calling WriteTCP and the other called ReadTCP.

  one of the delay of loops (or block) will be the other if both loops call their VI TCP at the same time right?

  The system is Windows 7 and Labview 2012.

  Kind regards

  Sebastian

  They are perfectly parallel.  Just write in one and read it from the other.  There is no conflict.

  See My TCP articles for more details.

• with third party applications, I can read and write on the external drive HFS + for windows?

  Hello

  I see with third party app I can read and write to external disk NTFS on the mac computer.

  then othrwise, then I can read and write on extern hardrive HFS + with application of third party windows computer.  So who are the best third-party applications to read and write HFS and if they are free of charge on the external drive?

  Thank you

  Johan

  Now that I understand your goal, check out http://www.ufsexplorer.com/rdr_hfsp.php but your YMMV.

• Help blackBerry Smartphones... 8530... language... Here you are... Add... Read and write Chinese English to the Japan

  Helooo I want download link and... A solution language how to add input more...

  Read and write in Chinese English language at the Japan in my blackberry curve 8530... OS 5.0.0. Bundle... 1675...

  Thank  You......................................

  Hello and welcome to the community!

  Please start by these KBs:

  • KB05305 Location of support for BlackBerry smartphones
  • KB17208 How to install and configure the language pack of East Asia on a BlackBerry smartphone

  If you get stuck somewhere, please be very explicit (the exact KB, the exact step, etc.) when you come back to ask for more.

  Good luck!

• Not possible to write space characters in the fields 'Subject and Message' [Send & Track]

  • Acrobat Acrobat Pro DC 2015.016.20039
  • OS X El Capitán 10.11.4

  Problem since the last update.

  1. File > Send file > Send and track...
  2. Choose "Send Invitations personalized (with track)"
  3. Go to the fields 'subject and Message.

  Problem: I can write a text in these two areas, but it is not possible to type any space character. The only solution I know is to copy a space character outside of Acrobat, and paste it in via the clip board.

  Does anyone know how to recover the ability to write normal.

  The keyboard is ok, no problem.

  Mrs. Willi Adelberger

  Hey Willi,

  Today we released a hotfix that resolves this problem on space/line jump does not work in the transmission and the railway. If you're not already updated to the latest patch, simply open Acrobat and visit help > check for updates to apply this hotfix.

  More details about this release and bug fixes is available here: https://helpx.adobe.com/acrobat/release-note/acrobat-dc-june-02-2016.html

  Please give it a try and let us know.

  Thank you

  -ashu

• How to read and write files .exe to soa using the file adapter?

  Hello

  I have a requirement, that I need to read and write files .exe to soa using the file adapter.

  Can someone help me.

  Thanks in advance,

  Divya.

  Hi Vijay,

  I tried with opaque. It works for me.

  Kind regards

  Adkins

• How the batch of photos of change in Version 2.0 of Photos... impossible to find the function.

  How the batch of photos of change in Version 2.0 of Photos... impossible to find the function.  If it has been deleted to "improve" the Photo experience?

  Lot, what exactly will change?

  Titles, Descriptions and capture date - Yes.

  Select the images you want to change the title or the description and to set-up the info (command-i) pane.  Enter the title or the description in the appropriate field and he will be assigned to all selected pictures.

  

  If you want to batch, change the title with sequential use attached many Applescripts provided by users in the Photos for Mac user tips section.

  Batch change/correction of dates is provided by the Image ➙ setting Date and time menu option:

  

  

• DVD/CD RW do not read audio CDs or data or save a blank CD, but that it's ok to read and write DVDs

  My DVD/CD RW drive will not respond to CDs of any type, void, audio or data.  It whirs for a few seconds and then more nothing.  No AutoPlay (even if she is selected and in the registry as a value of 1), and if I try to click on the drive, the old hourglass stand forever and if I click on new does not, unless I have the disc, it erases then back to normal.

  The drive works fine for DVD reading and writing.  I tried to little nearly every thread relating to problems of CD, and I ran out of hair out! I uninstalled it, unplugged, repluged, rebooted, reinstalled, you name it! PC has updated the driver when I try to update.  I did all the advice regedit I saw and still nothing!  Anyone?  Please?

  Hello

  You have disk problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD burning and)
  Playback of CD and DVD). So it is not unusual for parts from 1 or 2 to not work so that others do
  correctly.

  A CD/DVD cleaner might help.

  CD have a tolerance + - and your can read/write on the edge outside these discs
  tolerances. They may be delivered, but it is generally more economical to replace the disk.

  Several good info here:
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Notes on the troubleshooting and repair of readers of compact disks and CD-ROM Drives
  http://www.repairfaq.org/repair/F_cdfaq7.html#CDFAQ_014

  ===========================================

  This troubleshooting could not help if there is alignment and/or wear issues however it
  a shot.

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.