In the network on a Windows 7 host bridge

Similar Questions

• Network management problem, computer laptop Windows 7 will not find other computers on any network, however all other computers on the network can access Windows 7 laptop.

  Basically, the issue I'm having is that my laptop does not connect to any other computer to access the actions or other files.  Other computers on the network can access my computer laptop shares and files without any problems.  Operating system is Windows 7 Home Premium x 64.

  What I tried:

  restarted
  uninstalling and reinstalling the files and printers, sharing maps and restart after completion
  all disabled firewall
  tried with IPv6 enabled and disabled without change, so it is currently enabled
  tried on a Wi - Fi and the differences are listed below in the section work (work is wireless)
  able to ping other comptuers
  access to other computers is permitted by other computers

  problem extends over several networks, IE I noticed it at home last night and the followed problem my laptop at work this morning.
  The problem is slightly different on the two sites.

  At home:
  I can see the other computers on the network, but I am unable to access it, even if I have permission, but other computers can access to my laptop.

  At work:
  Cannot even find other computers on the network but they can find and access my laptop.

  I have worked on this problem of non stop for several hours and did much more than what is said, but I am unable to remember everything.  I should have been taking notes: P

  Here are the results of the ipconfig/all command (I removed the physical addresses for security reasons):

  Windows IP configuration

  Name of the host...: Radiation-G72
  Primary Dns suffix...:
  Node... type: hybrid
  Active... IP routing: No.
  Active... proxy WINS: No.

  Wireless Network Connection 2 wireless LAN adapter:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Microsoft Virtual WiFi Miniport adapt
  Physical address.... :  **
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes

  Ethernet connection to the Local network card:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. : hsd1.ga.comcast.net.
  Description...: Realtek PCIe GBE Family Controller
  Physical address.... :  **
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes

  Wireless network connection Wireless LAN adapter:

  The connection-specific DNS suffix. :
  ... Description: Atheros AR928X Wireless Network adapt
  Physical address.... :  **
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes
  Address IPv6 local link...: fe80::f4e3:cd1c:6952:eb4d % 11 (Preferred)
  IPv4 address: 192.168.2.7 (Preferred)
  ... Subnet mask: 255.255.255.0.
  Lease obtained...: Thursday, February 4, 2010 10:50:32
  End of the lease...: Friday, February 5, 2010 08:29:36
  ... Default gateway. : 192.168.2.1.
  DHCP server...: 192.168.2.1.
  DHCPv6 IOOKING...: 234890707
  DHCPv6 DUID customer...: 00-01-00-01-12-4C-6E-91-00-25-D3-3D-FC-9A
  DNS servers...: 192.168.2.1.
  NetBIOS over TCP/IP...: enabled

  Tunnel adapter isatap. {1797D168-6FC8-4DDF-8338-4E214119C26D}:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Microsoft ISATAP adapter
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Teredo Tunneling Pseudo-Interface:

  The connection-specific DNS suffix. :
  ... Description: Teredo Tunneling Pseudo-Interface
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes
  IPv6 address: 2001:0:4137:9e74:4ea:2920:b81a:cdc5 (Preferred)
  Address IPv6 local link...: fe80::4ea:2920:b81a:cdc5% 13 (Preferred)
  ... Default gateway. : ::
  NetBIOS over TCP/IP...: disabled

  Card adapt 6TO4 tunnel:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Microsoft 6to4 card
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Asked this question in the Windows 7 forum also because the problem was between windows 7 and Vista.

  Hello

  If it has started, you can try a system restore - an update "might" have caused the problem.

  1. try a system restore back to a point before that happened. And immediately thereafter enter
  Control Panel - Windows updates - top left settings and set it to download and informs you instead
  Automatic. Leave it until you are sure that everything is OK and then you can add them one at a time
  to troubleshoot BUT click right on and HIDE all the driver updates. Also stop at day of drivers like below
  and let this value - manually search for drivers when you think you need. (See how and why to)
  stop day of drivers below.)

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  To uninstall an update if you determine that there are problems - Panel - updated Windows - down left-
  Updates installed - uninstall

  I had completely forgotten the system restore!  While looking into the system restore, I found that when I moved into my new House and has cable Internet installed, the cable technology installed a program of comcast on my computer.  This caused me to not be able to connect with other computers.  After rolling back to install it before it works!   Thank you.

• Set the name of the network on a Windows 2012 without Active Directory Server

  I have a Server Windows 2012 I use for DHCP, DNS and NAT on a network without a domain controller, and I don't want to create a domain.

  When my Windows 7 clients connect, they identify the network with the name of 'network '. Is there a setting on the server, Windows 2012, that will allow me to change the name that clients identify the network with? I want something that is on the side Server and not to go and rename it on each client manually.

  I noticed low-end devices how as access points, modems etc use their own custom network that clients identify their network with, so I guess it cannot be something too difficult...

  Thank you in advance.

  Support is located in the Windows Server Forums:
  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer/

• Unable to connect to the internet with the NETWORK card and Windows Millennium Edition.

  Hello

  I turned on my old computer yesterday, who has installed Windows Millennium Edition. At the back of the computer is an Ethernet port which is marked as LIEN ACT. The NIC with this port is Realtek 8139 PCI Fast Internet Adapter. I spend two hours on the Internet configuration and I did and finally got connected, but then, a few hours after, something went wrong and the Internet and the NETWORK card has stopped working! And the card has disappeared from the Device Manager, but he's still showing in network in Control Panel. I opened the computer and I reconnected it to the slot, but it did not help. At the back of the computer next to this port are two LEDs - green indicates the power that lights up when I plug the Internet cable and the other orange indicates actual connection. But now these two LEDs are not indicating something even when I plugged in the cable to the Internet, which comes from my router. In the computer a Dial Up connection PCI is installed too, but I disabled it. I used Dial-Up in 2002. So, I need help.
  But I know that I can connect with this Ethernet card to the Internet because it worked for 3 hours, I've loaded the pages and downloaded programs.
  Please don't point, should I upgrade Windows!
  Thank you.

  Hi friend,
  You can try a Bing search on connectivity to Win ME, I don't know there are still a few old sites that are not taken down you will find a few FAQ on.
  I saw not a ME machine in too many years to count!
  Good luck on your adventure.
  B Eddie

• Cannot search the network for Microsoft Windows (XP SP3)

  Hello

  On holiday, I have a PC running Windows 8.1 and a former under XP (SP3), both connected to a Netgear router for Internet access.

  Under Windows, 8.1, the XP PC appear not at all, even when I search by name.

  The WinXP when I click (down posted by exploring folders) on "Microsoft Windows network", I got an Error Message:

  Impossible to scan the network, you have no network, or the network is not started.

  I've followed all the recommendations for sharing files between Windows 8.1 and XP:

  Same network type: private

  Even working group: PERSONAL

  Different names.

  Option of sharing files on two PCs in network settings.

  Windows 8.1, I chose: encryption 40 or 56-bit.

  I can share folders between your desktop in Windows 7 with Win 8.1 and Windows XP Home.

  File sharing has been possible, in my view, before I've upgraded to SP3 of XP last year.

  I know that Windows XP is not supported, but I need this old PC to display movies on my old TV (S_Video)!

  Thanks for your replies.

  MdParis

  In addition...

  You may translate the error of another language?

  On the XP computer.

  • Click Start, run, type "services.msc" (without the quotes) and click OK
  • Scroll down to "Workstation" (probably the last item in the list) and double-click it
  • Make sure the "Startup type" is "automatic".
  • Click on the 'Start' button (if the service has already started, please report this), and then click OK
  • Close the Services applet

• Unable to connect to the network wireless in Windows XP.

  Original title: connect to my new network

  I have a new wireless network and everything goes well on my new laptop with Windows 7 but I couldn't connect my old laptop running XP to my new network.  I followed all the instructions, especially taking a setup.exe on a flash drive, but the xp machine does not work it saying: he can't find the info he needs.  Can someone, please?  I am getting very frustrated.

  Hello

  1. what exactly happens when you try to connect the XP computer to the network?

  2. do you get an error message/code?

  3. If so, what is the exact error message you get?

  4. are you able to connect using the wired connection?

  Perform the following methods and check:

  Method 1:

  You can follow the steps in the article and check:

  How to troubleshoot wireless network connections in Windows XP Service Pack 2

  http://support.Microsoft.com/kb/870702

  See also: http://www.microsoft.com/resources/documentation/windows/xp/all/proddocs/en-us/wlan_client_configure.mspx?mfr=true

  
  Method 2: you can follow the steps and check.

  a. click Start.

  b. click run

  c. type cmd.exe , and then press ENTER.

  d. type the following commands, and press ENTER.

  ipconfig/flushdns

  ipconfig/registerdns

  ipconfig/release

  ipconfig / renew

  
  Method 3: check if the problem exists in a clean boot state:

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  
  Note: Make sure that you put the computer to a Normal startup once you are finished.

  Let us know if it helps.

• Windows XP sees Win 7 computers on the network, but not Windows XP-based computers (7 can see 7, but 7 can't see XP and XP cannont see XP)

  We just installed a new Netgear Prosafe 16 port switch.  We use a wired Linksys router.

  With 10 computers on the network, XP can't see XP or 7.  And sees only 7 other 7 computers.

  We are able to ping to all computers.  All computers have access to the Internet.

  Network neighborhood shows computers only 7 to 7.  XP doesn't show anything.

  Error message:

  "The Working Group is not accessible.  Migh Tnot you are allowed to use this network resource.  Contact the administrator of this server to find out if you have access permissions. »

  "The network path is not found."

  Thank you!

  Hello

  -Are you connected to a domain network or a home network?

  Please follow the steps below and we update with the results.

  Method 1: Error Message When you try to access a network Windows XP computer: "you might not have permission to use this network resource".

  Please follow the steps described in the following article and check if it helps.

  http://support.Microsoft.com/kb/913628

  Registry warning

  To do: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  322756 (http://support.microsoft.com/kb/322756/)

  How to back up and restore the registry in Windows

  Method 2: Error Message When you try to access a network share on a Windows XP-based computer: "workgroup is not accessible.

  http://support.Microsoft.com/kb/915107

  For more information, see the articles:

  Why can't I connect to other computers?

  http://Windows.Microsoft.com/en-us/Windows7/why-can-t-I-connect-to-other-computers

  Networking of computers running different versions of Windows

  http://Windows.Microsoft.com/en-us/Windows7/networking-home-computers-running-different-versions-of-Windows

  Let us know if it helps!

• How the network xp and windows 7 starter edition

  I can't see my computer windows xp on my Windows 7 computer's shared resources. I can't set up a homegroup because it's a starter edition. I can't change the name of the network on the computer windows 7. It remains as home, work, or public.

  Here is the Vista Forums.

  http://social.answers.Microsoft.com/forums/en-us/w7network/threads

  Windows 7 Networking Forum at the link above.

  For any question on Windows 7:

  http://social.answers.Microsoft.com/forums/en-us/category/Windows7

  Link above is Windows 7 Forum for questions on Windows 7.

  Windows 7 questions should be directed to the it.

  You are in the Vista Forums.

  See you soon.

  Mick Murphy - Microsoft partner

• NAS Lenovo IX2 disappeared from the network after a Windows update 8.1

  I have guys, after update my PC for Windows 8.1 Lenovo IX2 NAS work good for a few days, but for some reason he disappeared from the network.

  I do not have any IX2 or windows setting change. I is accessible from a browser like IE, by IP address or name (typing IX2), also the Media Center is recognized by the PC and the SmartTV.

  Windows Explorer does not show the IX after networks as usual and I can't access the mapped drives (shared forlders). Error 0 x 80070035 appears when I try to add a new network connection.

  This problem is driving me crazy for weeks! You have any how?

  Concerning

  Mariano

  

  Hello

  Thanks for posting your query on the Microsoft Community.

  I understand that you are not able to access the drives mapped network (shared folders).

  Before we continue, we need to know if you have made any changes on the computer before this problem.

  I suggest you disable the settings of the firewall and antivirus software to see if it helps.

  I suggest you check out the link below to fix the problem.

  https://social.technet.Microsoft.com/forums/Windows/en-us/028a3d13-f571-49E0-abe7-1ca61fb92082/error-code-0x80070035-the-network-path-was-not-found?Forum=w7itpronetworking

  : Referring link for problems of collective housing in the Windows below

  http://Windows.Microsoft.com/en-us/Windows-8/HomeGroup-problems-in-Windows

  Please let us know if you need help with Windows. We are happy to help you.

  Thank you.

• Uninstall the network adapter with Windows 7

  I can not connect to internet on my other PC with Windows 7.  In Device Manager, I found 9 network cards that I can't uninstall.  If this is caused by a virus?  How can I remove additional network cards from my PC?  Thank you.

  Hello Markopx,

  Thanks for posting in the Microsoft Answers forum! In order to remove any unwanted network adapters, simplyright click on the network adapter of your choice in the Device Manager and select Uninstall.

  Hope this helps J

  Adam
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• "No access to the network" problem in Windows 7 and error message "your computer seems to be correctly configured but the device or resource (DNS SERVER) is not responding."

  Hello, I have a desktop PC and a laptop (DELL Inspiron N-4050).
  I have problem with my internet connection cable which is working fine on my PC, but does not not on my laptop giving an error "no access to the network.

  When I troubleshoot it says "your computer seems to be correctly configured but the device or resource (DNS SERVER) is not responding."
  I said to many technicians of microsoft online response, but they could not solve my problem and said this is my DNS problem and advised me to contact my Internet service provider. Guess it's because of my internet so why it works on my PC not on laptop?

  Yesterday, my ethernet cable pulled out my cell phone and I couldn't connect to the internet more. But on my desktop PC, it works perfectly fine. (I do not use wifi, if this information is also required) I have studied several threads with similar situations, and I have tried different methods to solve the problem to no avail. I did a system restore, but I'm having no luck. Also, I did not of the latest changes with my anti virus software and my LAN card drivers look to date.

  When I remove my cable from the laptop and again connect my cable then it works but only after the PC sat for awhile.
  1.I did flush DNS by typing "ipconfig/flushdns" in the command prompt.
  2. my IP address, DNS, subnet mask etc are set to automatic.
  3.I also added physical address taken from command line giving "ipconfig/all". for the properties of the network driver settings.
  4.I ' installed the drivers to date of 2014 on my laptop.
  5.I did a lot of searching the web, but they do not solve my problem.

  Please help me to solve it.
  I appreciate your help.
  Thank you.

  Hello Hall,

  Please keep us updated on the status of the issue.

  I suggest you to follow the steps in this Microsoft article troubleshooting and check if it helps:

  Error message "your computer seems to be configured correctly, but the device or resource (DNS server) is not responding" in Windows 7

  http://support.Microsoft.com/kb/2779064/en-us

  Hope the helps of information.

  Please reply with the results, in order to help you solve the problem.

  Thank you

• I can't open up to manage the network connections for windows 7 there is no link for it

  When I go on the Network Center share there is no link on the side to manage network connections and I need to open

  Here are two shortcuts to network connections:

  • Press the Windows key + R , type ncpa.cpl in the box, and then click OK .
  • Click Start , type ncpa.cpl in the Start Search box and press enter .

  Boulder computer Maven
  Most Microsoft Valuable Professional

• How to change the network card eth0 eth1 on host (Linux Debian 5 "lenny") til

  Hello

  I just installed the server VMWare 2.0.1 for Linux 64 - bit version on my Linux Debian 5 "Lenny".

  The host is also my firewall and unfortunately I was a bit quick in accepting the default settings, and this is why I agreed for the network card eth0.

  I just installed my first virtual Ubuntu 8.10, but I can't see LAN, the virtual server is hung on the WAN card op.

  How can I change this?

  Just re-run the script vmware - config.pl who will take you through the network configuration again. Note to all virtual machines powered off.

  Guy Leech

  ---

  If you have found this device or any other answer useful please consider the use of buttons useful or Correct to award points.

• Pavilion G6-2244sa: cannot download the network drivers for windows 7

  Bought my laptop at home about 3 years that came with windows 8. I've replaced the operating system with windows 7 that I hated the feel of windows 8. Everything was fine until this year, when my internal hard drive is gone. I replaced with a new drive hard and loading the new windows 7. Must connect to the internet so that I can get all the latest drivers for the laptop. I am able to connect via an ethernate cable but unable to connect via wifi. I tried to download the latest drivers for this model but can't download drivers for windows 8.

  How to find the right drivers for windows 7. My warranty ran out last year. As this portable windows 8 is there a chance that I could upgrade to windows 10. I'm not savvy computer as I often to ask my co-worker or my COMPUTER service assistance.

  Concerning

  Richard73

  You're welcome, Richard.

  Here is the driver for the wireless card you need...

  This package contains the installation package driver for wireless LAN Qualcomm Atheros AR9000 controller series in the laptop models running a supported operating system.

  File name: sp61411.exe

• Network with UMTS card on host bridge

  Hello

  I'm testing the latest vmware workstation on windows xp sp3. The guest operating system is win xp sp3. To connect my host to the internet, I use my UMTS card. For the comment system, I need network bridge due to a separate IP address in the guest computer. After starting the virtual machine (my host is to connect to the internet via my UMTS card, I get the message: "the network interface on the VMNet0 device is dow because the bridged Ethernet Interface is...) ». If I connect my host via a cable network or WIFI to internet, everything works fine.

  How is it possible to connect my system of comments through 'bridge' to the internet?

  Thank you

  Joerg

  I don't know if I understand your problem. Your host is connected via UMTS and receives a public ip address. You try to connect to your comments via the bridge, which means also there need a public ip address, but UMTS only serve one of them (this is normal). Therefore, you must use NAT for your comments, so that your host and your guest use the same public ip address.