Install XP error Stop: 0X0000000A
Stop: 0X0000000A occurs when windows tries to access a particular too memory address high a process internal request level.hat do you mean? I have not correctly this part
* original title - troubleshoooting windows xp installation *.
Hi kofani,
Read the following article about your error:
http://support.Microsoft.com/kb/314063
I hope this helps!
Debra
Microsoft Answers Support Engineer
Visit our Microsoft answers feedback Forum and let us know what you think
Tags: Windows
Similar Questions
-
Error: STOP 0X0000000A (0XOOOOOOE8, 0 x 0, 00000002 00000001, 0X806E4A16.)
Original title: no update
For a month, I'm having a lot of problems
I have this computer for 8 years and so far, works very well, but after a month he gave me a lot of problems.
I have also formatted and receive sevral error messages
delay in writing, no disc, STOP 0X0000000A (0XOOOOOOE8, 0 x 0, 00000002 00000001, 0X806E4A16)
Help, please
Hi Kam.rani,
Thanks for the question.
It would be useful that you could answer this question to help you further.
1. you remember to make changes before the hardware or software issue?
2. you try to perform windows updates?
Here is a link that gives you steps to solve this problem.
You get a message error "Stop 0x0000000A (IRQL_NOT_LESS_OR_EQUAL) error code" in Windows XP
Note: The above article contains steps to disable the third-party antivirus software. Be sure to enable the security software on the computer after checking the issue.
If you need further assistance, please answer and we will be happy to help you.
-
Hello
Im trying to install xp pro on a hp compaq presario r3305ea and I am
stop above error I had trouble getting this machine to start
like the power just didn't keep turning itself off no beeps no warning I finally
managed to get it to stay on xp installed so I get blue screen
Anyone have any ideas?
GraemeHello
Your stop code () STOP 0X0000000A) indicates that a pilot or a kernel mode process tried to access a memory location that he had not authorized access to, or to an IRQL that was too high. From my experience, it is usually linked to bad RAM. Try to put the new RAM and see if that fixes the problem. Hope that helps! -
Blue screen error STOP: 0x0000000A
STOP: 0x0000000A irql not less or equal bvluescreen 1055 whats up?
What's new?
Hello
See this thread for more information on using BlueScreenView, MyEventViewer and other methods of
Troubleshoot the BlueScreens - top two responses.==============================================
References to Vista also apply to Windows 7.
Drivers could be at fault, however the problems of disk or security/antivirus/antispyware products are
just as likely to be the root cause that they can force a driver to corrupt or go out of bounds.
The video driver or something affecting it would be questionable.At the end of this message, I'll post a bluescreen generic and in the next convenience store
How do to update the drivers and BIOS but also to check memory message.-----------------------------------
BCCode: 0a 0x0000000A
Cause
This bug check is issued if the memory paged (or invalid) is accessible when the IRQL is too high.
The error that usually generates this bug check occurs after the installation of the faulty device driver or service system, BIOS.
If you encounter a bug 0xA control during the upgrade to a later version of Windows, this error can be caused by a device driver, system service, an anti-virus or a backup tool that is not compatible with the new version.
Solve the problem
If a kernel debugger is available, get a stack trace.
To resolve an error caused by the faulty device driver or service system, BIOS
- Restart your computer.
- Press F8 to character-based menu that displays the choice of operating system.
- In the WindowsAdvanced Options menu, select last known good Configuration . This option is most effective when a pilot or a service is added at a time.
To resolve an error caused by an incompatible device driver, system service, virus scanner, or backup tool
- Check the system log in Event Viewer for error messages that may identify the device or driver that caused the error.
- Try disabling the cache in memory of the BIOS.
- Run the diagnostics of equipment provided by the manufacturer of the system, in particular the scanner memory. For more information about these procedures, see the manual of your computer.
- Make sure that the latest Service Pack is installed.
- If your system has cards (SCSI) small computer system interface, contact the card manufacturer for updated Windows drivers. Try to disable sync negotiation in the SCSI BIOS, check the wiring and the SCSI ID of each device and confirming the proper termination.
- For devices (IDE) peripheral electronic integrated, set the built-in as only primary IDE port. Also, check each IDE device to the right setting master/slave/stand alone. Try to remove all IDE devices except for the hard drives.
If the message appears during installation of Windows, make sure that the computer and installed devices are listed in the list of the products tested Microsoft Windows market.
Comments
Before upgrading to a new version of Windows, remove all third-party device drivers and system services and disable any antivirus. Contact software manufacturers for updates of these third-party tools.
BCCode: 0a 0x0000000A<-- read="">
* 1025.html http://www.faultwire.com/solutions-fatal_error/IRQL-not-less-or-Equal-0x0000000A-==================================================================
General troubleshooting BlueScreen to use with the methods above.
Look in the Event Viewer to see if something is reported on those.
http://www.computerperformance.co.UK/Vista/vista_event_viewer.htmMyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
http://www.NirSoft.NET/utils/my_event_viewer.html-------------------------------------------------------------------------
Also this, so you can see the probable bluescreens.
Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
http://www.winvistatips.com/disable-automatic-restart-T84.html-------------------------------------------------------------------------
Here are a few ways to possibly fix the blue screen issue. If you could give the blue screen
info that would help. Such as ITC and 4 others entered at the bottom left. And all others
error information such as codes of STOP and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.As examples:
BCCode: 116
BCP1: 87BC9510
BCP2: 8C013D80
BCP3: 00000000
BCP4: 00000002or in this format:
Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000It is an excellent tool for displaying the blue screen error information
BlueScreenView scans all your minidump files created during 'blue screen of death '.
hangs and displays information about all accidents of a table - free
http://www.NirSoft.NET/utils/blue_screen_view.htmlBlueScreens many are caused by old or damaged, in particular the video drivers drivers however
There are other causes.You can do mode if necessary safe or the Vista DVD command prompt or
Options recovery if your system is installed by the manufacturer.How to start on the System Recovery Options in Windows 7
http://www.SevenForums.com/tutorials/668-system-recovery-options.htmlYou can try a system restore to a point before the problem started when one exists.
How to do a system restore in Windows 7
http://www.SevenForums.com/tutorials/700-system-restore.html-------------------------------------------------------------------------
Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN
Enter this at the command prompt - sfc/scannow
How to fix the system files of Windows 7 with the System File Checker
http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.htmlHow to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
generates cbs.log Windows Vista (and Windows 7)
http://support.Microsoft.com/kb/928228The log can give you the answer if there is a corrupted driver. (Says not all possible
driver problems).Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
How to run the check disk at startup in Windows 7
http://www.SevenForums.com/tutorials/433-disk-check.html-------------------------------------------------------------------------
Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
keyboard and mouse, as well as of other major device drivers.Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htmInstallation and update of drivers to 7 (update drivers manually using the methods above is preferred
to make sure that the latest drivers from the manufacturer of system and device manufacturers are located)
http://www.SevenForums.com/tutorials/43216-installing-updating-drivers-7-a.htmlHow to disable automatic driver Installation in Windows Vista - drivers
http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx-------------------------------------------------------------------------
How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
quit unexpectedly
http://support.Microsoft.com/kb/958233Troubleshooting Vista Blue Screen, error of JUDGMENT (and Windows 7)
http://www.chicagotech.NET/Vista/vistabluescreen.htmUnderstanding and decoding BSOD (blue screen of death) Messages
http://www.Taranfx.com/blog/?p=692Windows - troubleshooting blue screen errors
http://KB.wisc.edu/page.php?id=7033-------------------------------------------------------------------------
In some cases, it may be necessary.
Startup Options recovery or Windows 7 disk repair
How to run a startup repair in Windows 7
http://www.SevenForums.com/tutorials/681-startup-repair.htmlHow to start on the System Recovery Options in Windows 7
http://www.SevenForums.com/tutorials/668-system-recovery-options.htmlHow to create a Windows 7 system repair disc
http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.htmlI hope this helps.
Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.
-
I came to doday to find that a blue screen on my pc .This is the error number.
Blue Screen error code RQL_Less_or_Equal stop: 0X0000000A, C0xE10039F0, 0x000000FF, 0x00000000, 0x8056CA2E
Please provide additional information on your system:What is your system brand and model?What is your version of XP and Servie Pack?Describe your current antivirus and software anti malware situation: McAfee, Norton, Spybot, AVG, Avira!, Defender, ZoneAlarm, PC Tools, MSE, Comodo, etc..Click Start, run and enter in the box:Msinfo32Click on OK and when the system info summary appears, click on Edition, select all, copy, and then paste the information here.For information about video drivers, expand components, click view, click on edit, select all, copy and then paste the information here.There will be some personal information (such as the user name and the name of the system), and everything seemsbe personal information for you, just delete pasted information.This will minimize back Q & A and eliminate guesswork.Download BlueScreenView here:Unzip it and run it (BSV installs nothing) and let him complete the digitization of all of your files to dump.If you double-click on depressed, you will get information on it (including the field caused by the driver) and you should be able to spot the problem right away - especially if you see a model in landfills where Caused by field pilot is the same (beginning with this driver).Select (highlight) one or more of the most recent dump files by clicking on them and hold down the CTRL key to select multiple files. Try to select only the most recent links that relate to your problem (perhaps five or six to start dump files).Click on file, save selected items and save information from the dumps to a text file on your desktop called BSOD.txt. Open BSOD.txt with a text editor, copy the text and paste it in your next reply.Here's an example of report ASB to a single BSOD I initiated on purpose that indicates the cause of the accident as the pilot i8042prt.sys belonging to Microsoft Corporation:==================================================Dump file: Mini062110 - 01.dmpCrash time: 21/06/2010-11:51:31Bug Check String: MANUALLY_INITIATED_CRASHBug check code: 0x000000e2Parameter 1: 0x00000000Parameter 2: 0x00000000Parameter 3: 0x00000000Parameter 4: 0x00000000Caused by the driver: i8042prt.sysCaused by the address: i8042prt.sys + 27fbDescription of the file: i8042 Port driverProduct name: Microsoft® Windows® Operating SystemCompany: Microsoft CorporationFile version: 5.1.2600.5512 (xpsp.080413 - 2108)Processor: 32-bitComputer name:Full path: C:\WINDOWS\minidump\Mini062110-01.dmp==================================================Send information from 5 last memory dumps.While you wait for analysis, no matter what you use for protection against malware, please follow these steps:Download, install, update and do a full scan with these free malware detection programs:Malwarebytes (MMFA): http://malwarebytes.org/SUPERAntiSpyware: (SAS): http://www.superantispyware.com/It can be uninstalled later if you wish.Do not guess what the problem might be - understand and resolve it. I need YOUR voice and the points for helpful answers and propose responses. I'm saving for a pony!
-
Stop 0X0000000A error code received
I got a * STOP: 0X0000000A (0 x 0, 00000002 00000001, 0 X 00000034, 0X80664A16)
need help
* Title *.
I got a * STOP: 0X0000000A (0 x 0, 00000002 00000001, 0 X 00000034, 0X80664A16) ___need help__Control bug IRQL_NOT_LESS_OR_EQUAL 0x0000000A value a. This indicates that Microsoft Windows or a driver in mode accessed kernel memory paged at DISPATCH_LEVEL level or above.
If you have received a blue screen error, or stop code, the computer stopped abruptly to protect against data loss. A hardware device, its driver or software might have caused this error.
The error that usually generates this bug check occurs after the installation of the faulty device driver or service system, BIOS.
If you encounter a bug 0xA control during the upgrade to a later version of Windows, this error can be caused by a device driver, system service, an anti-virus or a backup tool that is not compatible with the new version.
Resolution
To resolve an error caused by the faulty device driver or service system, BIOS
Restart your computer.
Press F8 to character-based menu that displays the choice of operating system.
In the WindowsAdvanced Options menu, select last known good Configuration . This option is most effective when a pilot or a service is added at a time.
To resolve an error caused by an incompatible device driver, system service, virus scanner, or backup tool
Check the system log in Event Viewer for error messages that may identify the device or driver that caused the error.
Try disabling the cache in memory of the BIOS.
Run the diagnostics of equipment provided by the manufacturer of the system, in particular the scanner memory. For more information about these procedures, see the manual of your computer.
Make sure that the latest Service Pack is installed.
If your system has cards (SCSI) small computer system interface, contact the card manufacturer for updated Windows drivers. Try to disable sync negotiation in the SCSI BIOS, check the wiring and the SCSI ID of each device and confirming the proper termination.
For devices (IDE) peripheral electronic integrated, set the built-in as only primary IDE port. Also, check each IDE device to the right setting master/slave/stand alone. Try to remove all IDE devices except for the hard drives.
Please try these steps to resolve the problem.
Best regards
André"A programmer is just a tool that converts the caffeine in code" Deputy CLIP - http://www.winvistaside.de/
-
Error: STOP 0x0000007B while installing XP
Hello.
When I tryied to get xp installed on my laptop toshiba, I got this error: STOP 0x0000007B
I have a hard drive with this nummer serieal S/N 18LQT85GT
I heard that I needed a software to get this right.Can you help me for xp back?
Greetings
Boyfriend sorry but how to help if you didn t offers useful info?
What model of laptop do you have?
What Windows XP Home edition, you are trying to install? SP1 or SP2? -
Run a XP edition on my laptop, when a few days ago the system could not connect. It would increase logging in the stadium and then would suddenly return to the blue screen. The system records, in safe mode. Tried to restore the system to a date of return, but without success.
The message on the blue screen is like below, appreciate if there is no guidance on this. Perhaps a conflict of hardware or something like that...?
-----------------------------------------
IRQL_NOT_LESS_OR_EQUAL
..
..
..
STOP: 0X0000000A (0X00000002, 0X00000000, 0X017F0304, 0X8052746C)Hi Getafix1,
· Did you do changes on the computer before the show?
Follow these methods.
Method 1: Follow the steps in the article.
You receive an error message "Stop 0x0000000A" in Windows XP
http://support.Microsoft.com/kb/314063
Method 2: Follow these steps:
Step 1: Start the computer in safe mode and check if the problem persists.
A description of the options to start in Windows XP Mode
http://support.Microsoft.com/kb/315222
Step 2: If the problem does not still in safe mode, perform a clean boot to see if there is no conflict of software like clean boot helps you eliminate software conflicts.
How to configure Windows XP to start in a "clean boot" State
http://support.Microsoft.com/kb/310353
Note: After completing the steps in the clean boot troubleshooting, follow the section How to configure Windows to use a Normal startup state of the link to return the computer to a Normal startupmode.
After the clean boot used to resolve the problem, you can follow these steps to configure Windows XP to start normally.
(a) click Start, run.
(b) type msconfigand click OK.
(c) the System Configuration Utility dialog box appears.
(d) click the general tab, click Normal startup - load all services and device drivers and then click OK.
(e) when you are prompted, click on restart to restart the computer.
-
Original title: XP questions
I am running WIndows XP Pro SP3 on a Dell Optiplex gx270s and get several error messages stop "Blue screen" intermittent and different at startup (for protect my computer). Prompt notification Windows found problems with the file system and run CHKDSK/F. I am unable to do so as I can not find my administrator password (also necessary if you plan to run from my XP installation disc). Windows Fix - It Center, running 'Folder & troubleshooting' reports icons randomly change the icons but no resolves not. I didn't notice the icons change and do not if this is related to Stop what error messages at startup, I've been doing. Running a disk check during start-up and Diagnostics IDE are not problems. It lasts for quite awhile and I've delayed just deal with it because it is not always the case. A lot of program installs / uninstalls and Microsoft Updates since its start if the system restore wouldn't do me any good. Before reinstalling the operating system, what are my options? Is there a way to reset my ' Administor password ", or better yet does not require one, (it is a personal computer for personal use only and I don't remember why a password has been assigned)?
Here are some of the error messages:
STOP: 0x0000007E (OxC0000005, 0x89AD8000, 0xA579CCB4, 0xA579C9BO)
BAD_POOL_HEADER
Technical information:
STOP: 0 X 00000019 (0X00000020, 0X89D5FDA0, 0X89D5DC8, 0X0A050002)
IRQL_NOT_LESS_OR_EQUAL
STOP 0X0000000A
(0x6750300C, 0 x 0, 00000002 00000000, 0x804FFDB6)
Hello
You did changes to the computer before this problem?
The administrator password cannot be reset.
See the following article for more information: Microsoft's strategy concerning lost or forgotten passwords
In the following troubleshooting steps may help you resolve this problem.
How to troubleshoot a Stop error 0x0000007E in Windows XP
http://support.Microsoft.com/kb/330182FIX: Error Message When you connect a scanner or a digital camera to a computer that is running Windows Vista or Windows XP Service Pack 2: "BAD_POOL_HEADER STOP"
http://support.Microsoft.com/kb/934177You receive an error message "Stop 0x0000000A" in Windows XP
http://support.Microsoft.com/kb/314063 -
Original title: Windows has shut down to not to damage the computer
When I go to install windows, it gets a blue screen with this error:
STOP: 0X0000007B (0XF78D2, 524, 0XC0000034, 0X00000000, 0X00000000)Hello
See the article below that could be useful.
Advanced troubleshooting of errors "Stop 0x0000007B" in Windows XP
http://support.Microsoft.com/kb/324103 -
Trying to install creative cloud, stops at halfway and gives me error Code: 1.
Trying to install creative cloud, stops at halfway and gives me "error Code: 1'." When I looked at what that means, it tells me to uninstall, then try again. There is nothing to uninstall. I disabled my firewall and disable all security software. Even went to the properties to UNLOCK program to settle, giving permissions to all. Even as an administrator. Even tried in safe mode, nothing. Same mistake NEVER ONE TIME! Then I downloaded Adobe Assistant I think that another program... It installs and shows that the installed programs, but what that leaves is a folder on the desktop with the name of 2 programs, but there is nothing for them.
Using the Support Chat from Adobe is the ONLY way it worked! It just took about an hour. But I insisted for them to take over my computer. There was much too much that they had to do, open, and delete stuff. They had to download additional software to try to solve it. They had mistakes throughout, but now installed InDesign Creative Cloud AND. As I said, ask them to do it for you because it's worth against the endless hours, I tried to resolve the question of my own, search the forums, make suggestions, without success. Once I saw my program PASSES the bar of 42%, I knew that they fixed. They will still open the program to ensure that it properly installed. If you highlight the contact on the Adobe site, answer a few questions and then click on NEED of EXTRA HELP. Then connect to the chat. TOTALLY FREE! And you just sit back and watch everything they do, for about an hour. How long approximately it is. But they know what they're doing for sure. As I said, I tried all the available on websites, forums, chats and connect them directly to my computer support, IS THE ONLY THING THAT WORKED they are awesome if you get someone who knows what they're doing, unlike only one, that I had later in the night, which had no idea. I've disconnected and got another person, which sets the creative cloud. Now the rep just fixed and installed InDesign. Save yourself the extra stress as if I was, because I was so frustrated! They are awesome
-
Hi, need help, Windows stopped from STOP error code: 0x0000000A (0x00000000.0x00000000.0x00000002.
InnSafe in startup mode, blue screen, STOPS. IRQL_NOT_LESS_OR_EQUAL STOP: 0x0000000A (0x00000000.0x00000000.0x00000000.0x00000002.0x00000001.0x804DC11D)
I don't know how to download the content, normally I could rectify, but not this time, how it is done? racey21
-
Blue screen Windows XP start STOP: 0x0000000A (0x000000FF, 0x00000000, 0x006CED36, 0x805302F2)
Guru of any kind
I turn on my computer, and then after the already loaded windows logo, with the fact that I found a blue screen said
STOP: 0X0000000A (0X000000FF, 0X00000000, 0X006CED36, 0X805302F2)So, what should I do to solve this problem I have a bootable DVD, I could start in DOS now.For more details of this symtom.1. I installed NOD32 antivirus and use it for 2 days, already update the anti-virus databases, already sweeping the entire system, drive2. I found the GET bigger and bigger quarantine folder, so I try to remove (Ctrl + A, Del)then NOD32 program to happen does not not but the other program can still usecan I use the Task Manager to end NOD32 but cannot, it has been protected.If I click on start/turn off computer/Turn off shutdown of windows then3 after I turn on my computer, then after the already loaded windows logo, with the fact that I found a blue screen saidSTOP: 0X0000000A (0X000000FF, 0X00000000, 0X006CED36, 0X805302F2)
Thank you very muchSabrina CTake a look at the section "Error occurs after Windows XP is already installed" of this article in the Microsoft Knowledge base.
I recommend the boot without failure and then research on the issue.
To start in Safe Mode, until the small logo of Windows with a progress bar appears, press the F8 key. In the list of options, choose Safe Mode.
Now that the first troubleshooting step, uninstall ESET NOD32 using the NOD32 removal tool (download the file via a work computer, save it to a USB drive and take it to your affected PC booted without failure).
Once uninstallation is successful, restart the PC to see if the BSOD persists.
If the BSOD persists, try to boot mode safe again. Now click on the Start button, select all programs > Accessories > system tools > system restore. Select "Restore my computer to an earlier time" and click Next. Choose a restore point before the installation of ESET NOD32, usually it will be a created restore point automatically named "Installed ESET NOD32 Antivirus" or something similar. After choosing a suitable restore point, click Next. Click Next again to confirm the restore operation.
If only NOD32 UN-installing the problem you can try to re - install it or contact the ESET Support.
-
IRQL_NOT_LESS_OR_EQUAL, Stop: 0x0000000A (0x00000002, 0x00000000, 0x00000010, 0x80523E78)
New m/b: gigabyte ga-880ga-ud3h worm. 2.2, AMD phenom II x 6 1090 t. & Corsair 1600 mhz, dual channel, ddr3, 8 GB (2 sticks). 2 weeks-> PNY GT 430-1 GB, PCI-e 2.0; Antec 650w pwr supply, SATA 160 GB & 250 GB SATA; both the format installed XP, 35 min. to install devices then T.B.S. of D. CPU is between 33 & 34 C, Sys. c. 29
Hello
See the article below which might help you.
You receive an error message "Stop 0x0000000A" in Windows XP
-
My Vista system was crushed, tried everything, but finally resorted to a recovery of the original factory image off the coast of the hard drive Partition. Everything seemed to go smooth but now I get a blue screen at startup: irql_not_less_or_equal STOP: 0x0000000A (0 x 0, 00000002 00000001, 0x81AE8590)
Odd part is the system has two RAM slots, we have a 2 GB key and another has a 1 GB. Could not get the machine to start with two sticks in. Will start with a stick in each thin slot. Will not start no matter how they are installed if you are using the two RAM slots. Ran SFC/scannow. He found errors, that it cannot correct. How can I fix these errors?
CBS log is large enough: what details should I post it to help you troubleshoot?
Note: Were able to update the system, including the installation of updates Windows 128 and seems to be updated throughout the SP-2. I really don't want to run another recovery if possible.
Thank you!
Hello
Perhaps you have different brands of RAM in your computer, and so it would not start with the two inserted Rams. Do a check for your specific PC memory that tells you what products work with your system.
Follow the information in this article.
Know what type of RAM you needIn addition, updated BIOS.
Warning of the BIOS:
BIOS change / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.If scan SFC did not fix the issue, I would say that you follow the steps in this article to fix it.
http://support.Microsoft.com/kb/929833
Regarding blue screen errors, follow the steps in this article that applies also for Vista.
Maybe you are looking for
-
How to test if a Thunderbolt Display works
Hi, I'm going to buy a Thunderbolt Display on Craigslist. We meet in a public place, not his home. Is there a way to check and make sure the display is working? Is there some sort of menu that I can raise by simply plugging in the Panel to see if
-
Hybrid graphics driver after reinstalling Windows 7
Hello. I bought my laptop (Pavilion dm3-2015er) with Windows 7 already installed. I used it for awhile, but then decided to install another copy of Windows 7 that I had in my possession, in order to be able to redistribute space between disks in the
-
Invited guess receives not Gmail Cal event notification.
Hi all, I tried to search for it and don't quite have a simple answer to my question. I have a gmail account and use it to create all my calendar events. When I add my wife as a «who» in the case of field of creation, his correct gmail email returns,
-
videos online will not completely play without a break
When I play on line videos (youtube, etc) the video will not play all the way through without stopping several times during play.
-
Tried a system restore but restore has not initialized and went into a loop. After a long delay itwent on a BSoD and looping continues by saying that he could restart the computer. There can be no. Can't stop to do a reboot.