installation daqmx

Similar Questions

• Installation DAQmx 9.1.1 with LabView 8.2, but focused on the acquisition of library data do not appear

  I'm under LabView 8.2 on Windows XP, with an NI PCI-MIO-16XE-50 card. I tried to install DAQmx 9.1.1 on my system, but libraries DAQ do they not appear in the folder C:\Program NIUninstaller Instruments\LabVIEW 8.2\vi.lib.

  Here is the chronology of the events:

  After you add the DAQ card to my computer, I installed DAQmx 9.4. When I learned that 9.4 DAQmx is incompatible with LabView 8.2, I uninstalled and replaced with DAQmx 9.1.1 and installed the patch.

  I can see my device in MAX, but DAQ Assistant is not listed under functions > Express > entry in LabView.

  From advice on forums, I tried using Add/Remove programs to change NI DAQmx 9.1.1. Under 'Application Development Support' I see "Support of LabView 8.2" has a green check mark, but the text in the right panel says "this feature will not be installed. A newer version of this product is already installed on your computer. »

  I tried to "Repair" NI DAQmx 9.1.1 (and patch), but did not see a difference.

  I guess I need to uninstall the latest version of "Support of LabVIEW 8.2" before installing OR-DAQ 9.1.1, but there is no element of that name in Add/Remove Programs > National Instruments software. How uninstall this version of LabView Support for DAQmx 9.1.1 will install correctly?

  Or, if this is not the source of my problem, what is?

  Thank you!

  
  

• MAX corrupt? error-88302, list of odd DAQmx devices

  My ATE has stopped working Sunday morning with an error (I didn't witness) which led me to a corrupted driver OR DMM.  I had this happen a few times before, so I fixed (to the MAX).  This does not solve my ATE.  The sequence of events becomes blurred here, but at some point scroll sequence TestStand helped me to find that the PXI-2570 was not exploited.  I got an error message which suggested that the MAX database was corrupted, so I deleted the data folder and restart without solving my problem.

  The configuration in MAX shows a difference between this date and an equivalent system:

  

  Note that there are no green glyph near the PXI-2570.  That's what I'm focusing on today.  Also, why this device does not appear in the tree view on the left?  He does his sister ATE.  I swapped with a good map and it has not improved.

  I reinstalled 8.9.5f7 DAQmx because research on one other error (-88302) suggested that it would help.  There can be no.

  Any suggestions will be greatly appreciated.

  Hey Jim,.

  You are right that the PXI-2570 modules should appear under DAQmx devices.  This leads me to believe that the DAQmx driver is not installed correctly.  One possibility is that you have two different versions of DAQmx installed in different locations on your machine (Yes, it is possible .)  DAQmx is not designed to work with the instances simultaneously and is probably confused, thus failing to load the 2570... Unfortunately, this theory is not bullets, as the DAQmx 6233 is picked up correctly, but all bets are off when there are several DAQmx drivers installed.

  My first recommendation is to remove all the DAQmx facilities, check that there is no "DAQmx" installed in MAX version and then reinstall the original version of DAQmx on your ATE... no need to change the SW.  If this does not work, step up and functioning more simple troubleshooting is the image of the ATE from another machine.  Of course, this does not determine the root cause, but I think there is a change of configuration of the software.  In this case, the 88302 error internal NOR-ORB and should not be sent to the user in the first place... so I would say something is crazy with your installation DAQmx.

• driver installation problem 9171 with LV 8.5.1 and NIDAQ9.3

  Hello
  I just bought a NI9171 with a NI9477 DO Board chassis after checking the compatibility (driver, version LV). Everything seems to be ok, but I can't seem to get the right driver installed in NIDAQ 9.3. I tried with NIDAQ 9.4. Here, the driver has been installed correctly and I have done some tests in MAX, but my DAQmx LabVIEW library has been completely eliminated during the installation of 9.4... Re-intsllation of NIDAQ9.3 brought down the DAQmx library, but the driver no longer works. A thought is to copy the library addition and reinstall 9.4... but when it worked, it is not the right way to solve the problem. Could someone tell me if there is a problem with the Readme of 9.3 or suggest a solution to this problem? Unfortunately I have no shared services provider more and can not get direct support by OR ;-(
  Here you can find the Readme file:
  http://download.NI.com/support/softlib//multifunction_daq/nidaqmx/9.3.0/Readme.html#OS

  Thank you for any suspicion!
  Olli

  Hi Olli,

  Sorry for the inconvenience, but DAQmx 9.3 does not support 9171. There is mistake in our documentation. First, it was submitted to 9.4. However I have a solution for you. It is to install DAQmx components 9.4/9.5's to kernel with support for LabVIEW 9.3 DAQmx:

  (1) uninstall all versions of DAQmx

  (2) install DAQmx full 9.3 and restart

  (3) run the installer DAQmx 9.4/9.5

  a. Select custom, then click Next

  

  b. "Application Development Support", select "do not install this feature.

  

  c. click on through the next few menus until you reach "Start Installation". Make sure that Application Development Support is NOT under the upgrade section

  

  d. continue installation as usual and reboot.

  (5) the DAQmx palette should be in LabVIEW 8.5.1

  Please let me know if you have any question. Again, I apologize for the error.

• Installation of the minimum runtime for the program using the driver USB of NI-VISA personal

  I have a LabVIEW 2009 application that uses a driver for a USB device, created using the wizard of the Driver NI-VISA.  What my minimum installation of runtime needed to understand when I move it on a non-development machine?

  On my dev machine, I went to MAX and given my new camera USB one alias of VISA.  I think I'll meet trouble if my deployment includes no MAX on TIME machine.

  Right now, I guess the minimum is LabVIEW 2009 DURATION, NOR-DAQmx Configuration (including MAX) execution, duration of NI-VISA.

  If not, is there a method that avoids having to configure an alias altogether?  It would be nice to not not need NOR-DAQmx, I use not any material that my USB device with driver custom.

  Thank you!

  Not sure why you consider same installation DAQmx. You can install just MAX, the VISA duration and your harware MAX configuration. The installerallows of LabVIEW allows you to export the configuration, and then you select the option to import on the deployment computer. You will also need to include the installation of the inf file you created with the wizard.

• DAQmx without NOR-MAX?

  Hey Gang,

  I have developed a driver for the client using a PCI-6601 and DAQmx embedded application.  Now that we are in the deployment phase, the customer is shocked by the size of the NOT-MAX.  (a rudimentary facility is about 1.5 GB)  The only part of MAX that we use is to establish a connection between the PCI PnP and DAQmx resource name.

  Has anyone written a utility to PnP without MAX branch?

  Thanks for all the ideas,

  Roger

  Setup for DAQmx is a little big, but really not all that will be installed on the target system. However, I know a problem if you try to spread using a CD. Alternatively, you can ask end users to download on our Web site (www.ni.com.drivers), or you can host it on an internal network if your end-users are internal.

  I just ran the installer DAQmx (including MAX) with all selected and checked the cost of disk. It was a little less than 500 MB. Remove everything except kernel driver, MAX and the support of the API (I chose the support of Visual C++ without examples or integration) and it came out to 300 MB. Use the disc button in the installer to see what will be your condition.

• Problem DaqMx LabVIEW

  Hello:

  Installed Labview 2012 yesterday, daqmx was already installed (9,6) since I used it with Measurement Studio 2012.

  LabVIEW does not recognize DAQmx.

  I'm using Labview examples and get daq mx errors.

  Thank you.

  You must install DAQmx after LabVIEW. Since LabVIEW did not exist when you have done the installation DAQmx, LabVIEW required records would obviously not created.

• PCI-MIO-16-4 error 200329 after running a while

  I use a card PCI-MIO-16-4 for a combination signal generator and an oscilloscope for a student laboratory exercise.  I use ao0 to generate a variable frequency waveform (defined by the controls on the front panel) and ai6 to acquire the resulting signal.  To experience the two must be synchronized for the acquisition of scope starts simultaneously with the beginning of a generation analog.  Synchronization is performed using ctr0 in generation mode and set the same frequency as the analog output.  The meter output through rtsi0 for relaxation of beginning on the analog input.

  The application seems to work very well until the output frequency is changed "too quickly" while the analog input section will post 200329-error of the vi DAXmx Start Task.  After receiving this error, the computer must be restarted to resume operation of the Commission - even MAX panels will be simply repeat the same mistake on the analog inputs up to a reboot.

  If have tried the application on a Board of the USB-6221 BNC (using pfi9 to route the trigger start signal) and were unable to make the same error.

  It is on a computer running window 7 Enterprise sp1 with LabVIEW 2012 (32-bit) sp1 with the f5 patch installed.  DAQmx 9.6.2 has been installed for the original tests for both cards.  Installation DAQmx 9.8.0f0 does not change the behavior.  The PCI-MIO-16-4 passed the tests of the DAQ Diagnostic Utility 2.1.

  I tried using rtsi6 and rtsi0 as the routing without behavior change trigger signal.

  I have attached a stripped down version of the application that is always the problem.  There are 7 required files so that they are in a single .zip file.  With the frequency setting knob, it takes usually just a couple of "twists and turns" on the controller to cause the entry to the analog error.  The output of the DAQ Diagnostic Utility is also attached.

  Thanks for advice on what I can hurt in this application.

  The solution to the error:

  First attempt, the application had two structures of parallel events that have allowed the frequency be changed while there was also an acquisition that occur.  Modified to have a structure of single event so that the frequency changes may occur between acquisitions (risk of conflict Access Board?).  This made no difference to the error.  He would always get error-200329 after that the frequency has been changed several times.

  Discovered that just reset the jury would clear the error.  Considered catch the error and reset the jury whenever it happened.  Prefer something that will prevent the error from happening at all.

  Final solution was to erase the data acquisition task after each acquisition scan and reset.  It was only necessary erase the tasks of acquisition and not production jobs or a timer.  After several hours of change of frequency, amplitude and phase, no error had occurred.  I think that it has cured the problem.

  I now have two different copies of the application.  One is for use with the PCI-MIO-16-4 (new one that clears the task of acquisition after every scan) and one for use with the NI USB-6221, who uses still two parallel event structures, does never erase the task of acquiring and never shows the error when it is used with anything other than the PCI-MIO-16-4.

• Why LabVIEW 2012 does not support USB-6009?

  Hi all

  I recently installed LabVIEW 2012 and DAQmx 9.6 (and also tried with latest version) in my PC with Windows 7. I have the version of Explorer 5.4 measure and automation. I'm working with hardware DAQ USB 6009. Everything seems compatible, but when I try to post data acquisition, it fails. However, I used to use this device (since I bought it last year) with the other PC that has the Windows XP operating system and the older version of LabVIEW 8.5.

  What can I do with LabVIEW 2012 is a message "a 88302 error has occurred." and "This could be an internal error."

  If someone has an idea to solve the problem, please let me know.

  devkotaj

  Hi devkotaj,

  The USB-6009 device should work perfectly on Windows 7 with the software you have listed. This looks like a problem of configuraiton of material for me.

  What are you trying to do when you receive the error 88302? This error usually indicates a corrupt DAQmx driver, which may result from the installation of several DAQmx versions on the same machine. Have you tried repairing your installation DAQmx? I could uninstall DAQmx from the Control Panel before installing the latest driver. You can see our procedure to reinstall or uninstall recommenedd here.

  I hope this helps!

  Andy C.

  Engineering applications

  National Instruments

• Help with the knots of DAQ property

  Can someone please tell me how to change the types of property for a node property DAQ, I plugged my reference to data acquisition to the property node, choose the type of channel class, but how to choose which property to use with the channel node? I do not see drop-down lists of properties or anything like that. Clues on this on how to get the options for the node?

  Thank you.

  Very strange.  I suspect a problem with your installation DAQmx and try to reinstall or repair the data acquisition drivers.

  He has already worked on this PC?  You have another PC to try it?  I was able to select the property within your VI on my PC.

  I have attached your VI with the selected property node and a constant connected to it.

• USE 6009 does not save properly

  Problem: My USB-6009 seems not to register as a DAQ with Labview 2013 or NI MAX material, it is the symbol of a USB device instead of a DAQ hardware and there no properties or something like it (can't test, etc.), it simply lists the serial number, type, address and other trivial things.

  I tried: change the USB ports (as I saw someone already having a similar problem), this has not helped (it is change the address). I looked in my device manager, it records here as a "Data Acquisition Device' and says that everything is installed and up-to-date. I'm also currently repair my installation DAQmx in case that's the problem.

  I am running Windows 7 sp1 and I'm not sure how to do this because I recently acquired the USB-6009. Does anyone have recommendations?

  I hope you can help!

  -INeededAName

  Hello

  I looked into other people with similar problems, and it mainly boils down the DAQmx drivers. As you mentioned, please repair the DAQmx installation and reboot your PC. If you still have the same problem after that, ping - us a message, and we'll see what we can do.

  Best regards

  Soloman

• Integrate USB DAQ 6008 program Labview

  I'm new to LabVIEW and am currently writing a vi to access the 6008. I'm using LabVIEW 2012. I installed the driver NOR-DAQmx 3.6, however, the sample code is code c - no vi. Also, I can't see examples of NOR-DAQmx in the finder of the example. I downloaded various examples, but each are missing Subvi which I believe should be installed with the driver. All advice is appreciated.

  Harry,

  1 DAQmx Base is only supported on Mac OS.  You can find petitions on the exchange of idea ask for better support.

  2 DAQmx and all its beautiful examples are not installed on the Mac.  This means that the measurement and Automation Explorer (MAX) is not installed on the Mac and things such as the DAQ Assistant exist (although it is not a great loss).

  3. when DAQmx Base is installed on Mac OS X with LV 2012 you should have the DAQmx Base screws accessible from the measures of e/s palette.

  4 installation DAQmx Base includes a bunch of examples in this direction: Applications: National Instruments: LabVIEW 2012: examples: daqmxbase: However, the example Finder doesn't seem to know they are there, then you will need to manually search.

  One good thing about DAQmx Base is that it is almost entirely written in LabVIEW, so you can see what he does.

  Once you get past the obstacles, the USB-6008 case works well with DAQmx Base and the Mac.

  Lynn

• Assistant DAQ missing even after installation of 14.0 DAQmx f1

  Hello

  I am currently using NI LabVIEW student 2015 Edition. I have an NI USB-6009 data acquisition card, and it came with a marked installation CD OR-DAQmx 14.0 f1. Then after you install the software from the CD, I was looking for the DAQ Assistant, but he is still missing. No action in terms of getting DAQ Assistant on my VI?

  Best regards,

  Benjamin

  Install the latest DAQmx driver for compatibility with LabVIEW 2015.

• DaqMX Base read like waveform missing ability for Mac installation

  Now I have a VI running a signal with an average of program using tables as data types and the program takes up some memory, I was curious to try it by sampling the data as waveform as opposed to a table data types.

  The drop-down list of the DaqMXbase Read has no option of waveform and for some reason any 'DAQmx Read (analog 1 Wfm NChan NSamp d) .vi"is missing from the installation.  How to add this feature, or where I can find this specific file?

  Thank you.

  DAQmx DAQmx base drivers different and are, therefore, have different features. Since you are using Mac, you can use the DAQmx Base driver that has limited compared to the DAQmx features.

• Why the basis of NOR-DAQmx for LabVIEW options are grayed out using a custom installation (with Action: Skip)?

  I try to install NOR-DAQmx Base 3.7.0 LabVIEW 2013 (LV is installed). When I try to install Standard, it does not settle for LabVIEW (only the tools common and C and USB), but gives a successful installation message.

  

  When I try to custom installation, all the "...". for LabVIEW 20XX"options are unchecked, dimmed and Action says 'Skip '.

  

  I try this on a 2011 MacBook Air 11 '' running OS 10.9. LabVIEW works very well.

  Thanks for your suggestions.

  Hello

  DAQmx Base gray if poster LabVIEW Installer is not detected on the LabVIEW support system. Did you install LabVIEW and then move it to another location?

  The LV location controls DAQmx Base is...

  / Applications / National Instruments/LabVIEW LabVIEW.app

  Thank you

  Steven T.