Installtion stop at the stage of "usb module loading.

Similar Questions

• HP Pavilion DV6535ep power Jack / USB module compatible numbers

  Hello

  My HP dv6535ep has recently begun to turn off randomly. At first, I thought it was because of the temperature of the CPU/GPU but then discovered that he was in fact the power jack which became very hot and it has partially melted. I completely disassembled the laptop and inspected the power Jack / USB module and not found other flaws that a charred soldering point corresponding to the + 19V input line. I tested the power cable and the PCB board for short circuits, there is everything. I also tested the diet that works. Since the tip of electric power cable have significantly melted, I replaced with a new cable and assembled the laptop again. However the problem persists, with the new power supply tip, the tip and connector instantly becomes very hot when the laptop is turned on. The laptop does not even pass the BIOS/POST, she shut it down. For completeness, I will add that the blue power jack light is on once I connect to the edge of power.

  So in summary:

  * After you turn on the laptop, the DC power connector tip and jack become very very hot in a matter of seconds (point melt the end if not immediately disconnected).

  * The power DC jack light is on after plugging in the power.

  * The laptop often depends not at all and when it does, it stops during the BIOS POST.

  * The power supply is working (I have tested) and the power cable and points work too (I replaced with new parts).

  Then, leading me to believe the power Jack / USB is defective and must be replaced and that's the reason why I am writing here in the first place. You would be so kind and provide the power Jack / USB board of part numbers that are compatible with my laptop? Current reference number (defective) power Jack / USB card is

  DDAT8APB3002907

  I have difficulties to find exact matches on the surplus stores, where the best that I got is DDAT8APB300XXXX, where the last four digits do not match. Are they compatible?

  In hoping to hear talk about you,

  Thank you

  -Angelo

  PartSurfer information:

  446524-001 in stock USB ports and card power connector - for connection of adapter CA 90 watts RoHS: change	40,38	0.00	40,38
  449454-001 in stock USB ports and card power connector - for connection of 65 w AC adapter RoHS: change	40,38	0.00	40,38

  You'll have better luck he is looking through the references above. The price seems a little dirty to me and you might have more luck on ebay or a House of rooms online.

• Resize the stage to the size of the browser

  Hi all

  I wonder how do I prepare my ground to resize the size of the user's browser and keep the Center main movieclip.  But I don't want the scene to scale, I want the physical limits to grow without scaling the content.

  The reason for this: I have something that we will call it 'snow' falling in the background.  When the browser is also, I don't want the scene scaling and the snowflakes GET bigger or smaller, but have the stage show more space for the flakes of snow fall.  I already have the snowflakes falling outside the current boundaries of the scene, I wonder how the stage limits dynamically extend the size of browsers.

  Thanks a ton!

  In the publishing settings, make sure that HTML is selected on the Formats tab, and then in HTML, tab select 'percent' for "No. Scale" drop-down box for the scale and Dimension . Use Stage.stageWidth and Stage.stageHeight to retrieve the dimensions of the stage while SWF is loaded into the browser to position elements on stage. But note that coordinate (0,0) will always be in the same position according to your dimensions of original scene independently with or without browser.

• My computer has stopped recognizing the HP7450 printer, although showing the connection to the USB "ready".

  My computer has stopped recognizing the printer plugged in usb port

  Hello

  ·        You are able to print a test page for your printer?

  You can try the suggestion given in the article below and check if that helps get the printer to work.

  http://support.Microsoft.com/kb/308028

  Hope this information is useful.

  Amrita M

  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• How to stop the CC ability to drag the stage horizontally

  Hello

  I use the trial of CC in fact I use CS3 where I had a certain mode for the view of the stage. I want a fixed scene = no horizontal movable stage on its border. I don't like that my document is hidden on one side. It bothers me a lot and it feels like its never centered. His practice. I want to scroll through as I drag a Web page. Not on the side.

  Thanks for your help

  I guess you hate this check mark (sorry I don't have the English version)

  

  Fenja

• Satellite X 200-F stops during the game

  Hi guys,.

  I am a happy owner of a beautiful X 200-F for almost a year, and never had any problems with it.

  Last night, I was playing a heavy 3d game in the night in a room at near 30 ° C (we do not have a lot of conditioners of Air in France, it is not so hot, usually).
  So after an hour or 2 of battle in my laptop forged Alliance made a stop itself instantly, and it was because of overheating.
  I would make an egg on the back cover if I wanted :D

  I confess that I was playing in my bed, and it's not the best to do in summer, but I just want to know what is the critical temperature of the GPU that trigger the hard stop?
  And the temp of the CPU max?

  I checked & do all my usual test I didn't lose any performance of these two CPU & GPU.

  Thanks to new Toshiba laptop robust I'll be more careful next time ^^

  And thanks for your replies,

  Grettings from France

  Best regards

  Davith

  Hello

  Ok. It was a hot day, you've played the game of high performance, and you used the laptop in bed

  Good boyfriend I don't wonder that your laptop overheats and shuts automatically.

  First of all you shouldn't t use the laptop in bed, as this is very dangerous for the material of the laptops. Cooling modules may not work correctly if the vents are blocked and there is no air circulation.

  Secondly the phone automatically stops to avoid internal parts such as the CPU or GPU from damage.
  The high internal temperature can lead to hardware failure, so my advice is very simple

  Don t use the laptop in bed, but still on the table. Also, check that there is enough free space around the laptop. It is important to make sure that air can circulate properly.

  See you soon

• Satellite L20-182: after installing the OS only USB 1.1 not 2.0

  Hello, I am an owner of the model Toshiba Satellite L20-182.
  Recently I did a format disk and installed Windows XP Professional with Service Pack 2.

  Unfortunately, the system detects USB as a version 1.1.
  I find anywhere USB 2.0 drivers.

  Could you help me?

  Hello

  Why suggest that you have only the USB 1.1 and USB 2.0?

  To my knowledge you will not find any special USB Toshiba drivers Toshiba page.
  Each unit of Toshiba uses the current Microsoft Windows USB drivers and it s not necessary to install the special USB drivers.

  I assume that you have installed the operating system from the original CD of Microsoft and not the Toshiba back CD. Am I wrong?
  In this case you must install all Toshiba drivers that are available in the right order. The chipset utility is very important! Generally, the chipset must be installed at the first stage.

  Please also check this Microsoft documents:

  Availability of the updated Windows XP SP1 USB 1.1 and 2.0
  http://support.Microsoft.com/?kbid=822603

  When you install Windows XP Service Pack 2, the USB 2.0 drivers do not appear to be updated
  http://support.Microsoft.com/kb/873169

• It is possible to activate the "wake on USB" on a Satellite C870-142?

  It is possible to activate the "wake on USB" on a C870-142, specifically the USB 3.0 port? In Device Manager the USB 2.0 root hub properties have the "allow this device to wake the computer" greyed out, while the properties of USB 3.0 root hub is not a power management tab. All have the latest drivers from Intel, not obsolete Windows Update ones.

  There is no other choice that I don't see in the InsydeH20 BIOS, which is the latest update to version 6.80 site Toshiba drivers - I have not tried to find/load another version of BIOS. I want to install a USB adapter, Gigabit LAN, but should he Wake on LAN (who works with the NETWORK card internal fast ethernet). He has "allow this device to wake the computer" is checked, but I guess that's irrelevant if the USB port to which it is attached is not enabled.

  In case this wake on USB feature isn t available and supported by the BIOS, you won't be able to use it.

  Note: you cannot use any BIOS! You must use the BIOS available on the Web from Toshiba website. Use of other BIOS may damage the module EPROM and motherboard.

• flat sequence stops after the first image

  Hello

  I use USB-6218 to drive a current source and read the voltage at the terminals of shunt resistance in my circuit. In order to safely run things, I wanted to make sure that when I stop my blood 'on demand' vi, I updated the current 0. To do this, I tried to use the sequence of dish (find in annex vi), but my program never leaves the first image, even after it hit the stop on my front button.

  Can someone help me with this?

  Thank you
  Katarina

  Does not change the value of Stop inside the Subvi and the loop runs continually.

  -Suggest to check this example: http://www.ni.com/example/28769/en/

• Find the cDAQ and command module at startup

  Hello

  I have a cDAQmx (8 slots) with USB port and a module of series C. 4 modules are digital 4-channel input (up to 220 v), 1 analog input, analog output 1, 2 digital output, etc...

  I want to make my program (for testing electronic cards) is:

  (1) at startup, check if the cDAQ is present in the system (i.e. USB is plugged, drivers were already installed correctly)

  (2) also check the modules which are plugged into the cDAQmx and check if they are in the correct order.

  For example, to test the product X I need two digital inputs to slot 1 and 2 and an analog input to slot 3.

  I ask this because people in production could make the mistakes I want to avoid:

  (1) avoid forgetting to plug in the USB and begin the test

  (2) avoid to connect the wrong terminals! The plug is the same for each module, so it is possible teoretically put the connector in a 10V analog input to 220V, causing a serious injury (I know they are protected, but I want to avoid this risk).

  For the chassis, you should be able to query "Device Module names" to get the name of each module currently in the chassis:

  

• In the user interface, how can I property "Sequence Call Trace Setting" the stage of 'SequenceCall '?

  Hi all!

  I am writing a user interface. I want know step "SequenceCall" is tracingEnable or not. It is said that "use the Step.Module property to get a reference to a SequenceCallModule object. I can't well it. I can get a reference using "TS adapter API. But how he dose associated with the stage of 'SequenceCall '.

  Thank you!

  Hello

  You can do by using the node of given Variant to in LabVIEW.

  Please see the newsletter - get a different for TestStand objects Interface topic in the manual using Labview and LabWindows/CVI with TestStand for more information and an example.

  You can get a copy of this manual from this link - http://digital.ni.com/manuals.nsf/websearch/B8398AF8729D906F862577B4004FF10C if necessary.

  Concerning

  Anand jegou

  National Instruments

• HP DeskJet 2546B: Deskjet 2540 stops in the middle of the print page

  I was not able to connect my computer to my pc via wifi a colledge, so I connect my printer via the usb port on my pc (I use the white cable provided with the printer that connects to the back of it). Impression of normal word documents is very well, but I have been tring to print several pages of a pdf file and it stops a few lines of print. No error message, no warning sounds, just stops. The power light flashes too.

  The cord is still plugged, it says in my devices on my pc that is always connected, and I can see the print job in my what. I can delete from my without any problem and it will spit the rest of th page. If I leave without doing anything, he will spit the pages finally after one minute. It will always work in Quebec of the printer, but it won't do anything with it.

  And I can't seem to convert the content of the pdf in word format to work around the problem.

  What can I do to fix this?

  Hi @Roket107,

  Thanks for joining the Forums of HP Support for a solution to your printing problem.

  I understand that you are using a HP Deskjet 2540 all-in-One printer with a Windows 10 computer and when you try to print from a PDF file the print job stops printing without any error messages, but seem to print correctly from MS Word. I would like to help.

  I would start by checking the printer software installed by downloading and running the tool HP Print and Scan Doctor. This tool can diagnose and solve many problems of printing software and printer.

  It could also help to ensure that the updates of Windows are updated.

  If HP Printy and the Scan doctor does detect no problem with printing software, perhaps that the software used to view and print PDFs must be updated, or uninstalled, then reinstalled.

  Please let me know if that solves the problem, or if you need assistance.

  Indeed, if this help you to achieve a solution please click the 'accept as Solution' and the 'thumbs up' buttons down below in this message.

  Thank you!

• update my laptop stop recognizing the driver of Bus controller universal external hard drive.

  Recently my laptop stop recognizing the external hard drive. It was working fine before. The MFG. external IOMEGA Hardrive said universal Bus controller driver to be upgraded. It is Intel (R) 82801DB/DBM USB 2.0 Enhanced Controller pipe - 24CD. My several attempts to install an automatic update of the driver from the Intel Web site has failed.  What to do next?

  Hello

  1. which is the version of the service pack installed on the computer?

  2 have you made any changes to the computer before the show?

  3. What is the exact error message?

   
   
  I suggest you perform the steps described in the document:
   
   
  How to get and install the USB 2.0 drivers in Windows XP Service Pack 1
  http://support.Microsoft.com/kb/329632
   
   
   
  I hope this helps.

• As that I start my computer I get the error message "Rundll: error loading C:\windows\idoroyuyevev.dll the specified module could not be found." How should I do?

  Original title: Rundll error help

  As that I start my computer I get the error message "Rundll: error loading C:\windows\idoroyuyevev.dll the specified module could not be found." -What it means and how to fix it?

  It is sometimes easy to get rid of the error message by doing something like disable the startup item in msconfig (if you can still find), but I suggest you fix the problem and difficulty not only the symptom of the problem by simply deleting the startup message.

  I would also not recommend you start digging in the registry to try to find the startup item and remove it unless you have a backup of your system or at least a backup of your registry, because there is no 'Cancel' or 'quit without saving changes' option in regedit.  If you make a mistake, that's all.

  These ideas relieve 'rapid' and sometimes risky of the symptom if they not even work at all, but they can't actually solve the problem.  Also, I'd be suspicious of ideas that begin with the words "try."  You don't need to try things, you need to fix things.  You don't need to try ideas that might work, you must do something that will always work all the time.

  Here are the detailed instructions that protect you and solve your problem in the 'right' way.

  There is very little. DLL files that should be loaded from the C:\WINDOWS folder and is not one of them.  If you do not have a good explanation for the name of the file in a Google search, the chances are good that your system is currently or has been infected by malware.
  A "Cannot find...". ', ' Failed to start..., "Could not load..." ». "Might not work... "" Cannot run ""error loading... ". "or"specific module could not be found"message at startup is usually related to the malware that has been configured to run at startup, but the referenced file has been removed after a malware scan, leaving behind him a startup item or the registry entry pointing to a file that does not exist.
  It might be a removal of malicious software or an application not installed.  The entry may have a curious looking name since it was probably generated at random when the malware was installed. If you search your system for the referenced file, you may not find.
  Windows attempts to load this file but cannot locate because the file has been deleted for most probably during an analysis of the malware. However, an orphaned associate of remainders of startup parameter or registry entry and tells Windows to load the file when you start or connection.
  So you should delete the referenced entry Windows stop trying to load or run the file. It may or may not be included in the registry, but you can find it.  Autoruns (see below) you get the elements no matter where it is.

  You must be sure to solve the problem and not just fix the symptom of the problem by simply relieving your message - system is not a fix (there is a difference).

  If you just locate and uncheck the item in msconfig, which disables the element but does not remove the reference to the element of false starting your computer.   The msconfig program is not a Startup Manager, that's a troubleshooting tool.  Disabling things in msconfig to put an end to the messages and think that your problem is solved is short-sighted and leave behind him a sloppy XP configuration.  Just disable the display of a start-up error message should not count as a 'solution' to the problem.
  If you are comfortable editing the registry, you can find and remove the reference directly from there or remove it using a popular third-party tool called Autoruns.  The problem can always be found in the registry well.
  Before making any changes to your registry by hand or with third-party tools, don't forget to first make a backup of the registry
  . There is no cancellation or exit without saving the option in regedit.
  Here is a link to a popular registry backup tool:
  http://www.SnapFiles.com/get/ERUNT.html
  You can also use the Autoruns to find the element of start remains little matter where he's hiding.  Autoruns does not install anything on your computer.  It will display all startup locations where the reference may be then you can turn it off or remove it completely.  Here is the download link for Autoruns:
  http://TechNet.Microsoft.com/en-us/sysinternals/bb963902.aspx
  Run Autoruns.exe and wait that he at the end of the filling of the list of entries.
  When the Autoruns is finished scanning your system, it will say "Ready" in the lower left corner.  Autoruns can be a little intimidating to first if you have never seen it before because it displays a lot of information.  You are really interested only a few sections.
  The problem is usually to start the system or the user startup entries, then click the connection tab and see if the startup item is there.
  Scroll through the list and look for a boot entry associated files in the error message.
  If you can't find on the connection tab, look in any tab.
  You can also click file, search to search for logon, or any tab for all or part of the name of the element.
  Right-click on the offending entry and choose Remove.  If you are not sure what it is, you can just turn it off, restart and if the problem is resolved and things are functioning normally and everything works fine, then remove the offending entry.  If you don't see it in Autoruns, you may edit the registry and remove the item from your startup folder it.  Autoruns shall display the same information however.
  Given that your system has or has had an infection, follow up with this:
  Perform scans for malware, and then fix any problems:
  Download, install, update and do a full scan with these free malware detection programs at:
  Malwarebytes (MMFA): http://malwarebytes.org/
  SUPERAntiSpyware: (SAS): http://www.superantispyware.com/
  They can be uninstalled later if you wish.
  Restart your computer and solve the outstanding issues.

• C:\windows\ayofeworit.dll the specific module could not be found, the message pops up when loading office

  C:\windows\ayofeworit.dll the specific module could not be found, the message pops up when loading office

  Here are the detailed instructions that protect you and solve your problem in the 'right' way.

  There is very little. DLL files that should be loaded from the C:\WINDOWS folder and is not one of them.  If you can't find a good explanation for the name of the file in a Google search, re chances while your system is currently or has been infected with malicious software.

  A "Cannot find...". ', ' Failed to start..., "Could not load..." ». "Might not work... "" Cannot run ""error loading... ". "or"specific module could not be found"message at startup is usually related to the malware that has been configured to run at startup, but the referenced file has been removed after a malware scan, leaving behind him a startup item or the registry entry pointing to a file that does not exist.

  It might be a removal of malicious software or an application not installed.  The entry may have a curious looking name since it was probably generated at random when the malware was installed. If you search your system for the referenced file, you may not find.
  Windows attempts to load this file but cannot locate because the file has been deleted for most probably during an analysis of the malware. However, an orphaned associate of remainders of startup parameter or registry entry and tells Windows to load the file when you start or connection.
  So you should delete the referenced entry Windows stop trying to load or run the file. It may or may not be included in the registry, but you can find it.  Autoruns (see below) you get the elements no matter where it is.

  You must be sure to solve the problem and not just fix the symptom of the problem by simply relieving your message - system is not a fix (there is a difference).

  If you just locate and uncheck the item in msconfig, which disables the element but does not remove the reference to the element of false starting your computer.   The msconfig program is not a Startup Manager, that's a troubleshooting tool.  Disabling things in msconfig to put an end to the messages and think that your problem is solved is short-sighted and leave behind him a sloppy XP configuration.  Just disable the display of a start-up error message should not count as a 'solution' to the problem.
  If you are comfortable editing the registry, you can find and remove the reference directly from there or remove it using a popular third-party tool called Autoruns.  The problem can always be found in the registry well.
  Before making any changes to your registry by hand or with third-party tools, don't forget to first make a backup of the registry. There is no cancellation or exit without saving the option in regedit.
  Here is a link to a popular registry backup tool:
  http://www.SnapFiles.com/get/ERUNT.html
  You can also use the Autoruns to find the element of start remains little matter where he's hiding.  Autoruns does not install anything on your computer.  It will display all startup locations where the reference may be then you can turn it off or remove it completely.  Here is the download link for Autoruns:
  http://TechNet.Microsoft.com/en-us/sysinternals/bb963902.aspx
  Run Autoruns.exe and wait that he at the end of the filling of the list of entries.
  When the Autoruns is finished scanning your system, it will say "Ready" in the lower left corner.  Autoruns can be a little intimidating to first if you have never seen it before because it displays a lot of information
  .  You are really interested only a few sections.
  The problem is usually to start the system or the user startup entries, then click the connection tab and see if the startup item is there.
  Scroll through the list and look for a boot entry associated files in the error message.
  If you can't find on the connection tab, look in any tab.
  You can also click file, search to search for logon, or any tab for all or part of the name of the element.
  Right-click on the offending entry and choose Remove.  If you are not sure what it is, you can simply disable, restart and if the problem is resolved and then remove the offending entry.  If you don't see it in Autoruns, you may edit the registry and remove the item from your startup folder it.  Autoruns shall display the same information however.
  Given that you had or have an infection, followed with this:
  Perform scans for malware, and then fix any problems:
  Download, install, update and do a full scan with these free malware detection programs:
  Malwarebytes (MMFA): http://malwarebytes.org/
  SUPERAntiSpyware: (SAS): http://www.superantispyware.com/
  They can be uninstalled later if you wish.
  Restart your computer and solve the outstanding issues.