interface error

Similar Questions

• HP Scanjet Enterprise 8500 fn1 web interface error

  firmware: 2201075_229194

  When you use the web interface of the scanjet 8500, I click on the general tab and get the following error:

  "An unexpected error has occurred. We apologize for the inconvenience. Please try again. »

  "An unknown error has occurred on this page and has been registered. We apologize for comfort. »

  "It is probably due to a mistake in the functionality of the page. Try the links to return to a functional page. »

  Some links work however, the system is unusable to me in its current state.

  I updated the firmware in the hope that it could solve the problem, it does not.

  I did a factory reset, which proved to be unnecessary.

  The event logs provide these errors:

  event: 49.03.0C FW: 2201075_229194 Description: internal error framework employment

  event: 44.A0.31 FW: 2200648_228389 Description: operation not properly sequenced

  Nothing else has been saved since the Firmware upgrade, days ago

  Any help would be greatly appreciated.

  Has finally managed to get hold of someone at HP. I still don't know what caused the error, but more important still, they managed to restore the scanner to give me all the features of the web page.

  (1) to restart the parser

  (2) while the scanner is restarted, press ESC on the keyboard several times

  (3) select 'Administrator', press ENTER.

  (4) (4) mettre put in light 'Partial own', press ENTER.

  5) press ENTER to accept the partial clean

  (6) press the button 'B' for you back to the main menu

  (7) highlight 'continue', press enter

  This restarts the scanner after a few minutes and I was able to get full access to the web interface. I want to emphasize that the network settings has not changed which was very convenient.

• Reference Dell Equallogic Interface errors

  Hi guys, I got a big problem here in my room. My equallogic iscsi interfaces have a lot of erros. What can be?

  

  First of all, make sure you run the latest version of FW and SANHQ table.

  Packet errors are often the cause of bad cable, bad switch ports and a misconfiguration on switch iSCSI ports.   The only way to erase the mistakes of packages on Equallogic arrays must restart the table.

  • Replacement cable between the controller port and switch port with known good cable.

  • 10 GB cables must be SFF-8472 compliant to work with 10 GB Equallogic arrays.

  • Confirm that the switch is a minimum firmware to work with Berry Equallogic en.community.dell.com/.../2661.equallogic-compatibility-matrix

  (Note: if unable to switch, you can disable protocols spanning tree on ports connect to the table).

  • Use the tech TR1017 report to verify the configuration of the switch and confirm it meets best practices.

  • Run a show of support on the switches to review port errors.   If a Powerconnect or Force10 switch then engage networks dell help examine the switch logs. If another provider, and then engage the seller to switch to help examine the switch logs.

  • Cards network host to firmware update and the latest network card driver

  • The direct link to TR1017:

  Media.Community.Dell.com/.../tr1017-v4-Network-Guidelines.pdf

  If the host Linux with Multipath.d, you may need to modify the multipath.conf file to include: tur path_checker in the devices section.

  Joe

• Entry interface errors

  We see entry errors on the Gi0/1 interface on cisco 1941/K9

  Also, after reset the counters, we see these errors is cumulative once in 2-3 hours

  Any suggestions where to start?

  See logging no signal is today all the...

  #sh int gi0/1
  GigabitEthernet0/1 is up, line protocol is up
  Material is CN Gigabit Ethernet, the address is bc16.2222.1111 (bia bc16.2222.1111)
  Description: For the LAN-Lehavim
  The Internet address is 172.16.55.2/29
  MTU 1500 bytes, BW 1000000 Kbit/s, 10 DLY usec,
  reliability 255/255, txload 3/255, rxload 1/255
  Encapsulation ARPA, loopback not set
  KeepAlive set (10 sec)
  Full-Duplex, 1 Gbps, media type is RJ45
  control output stream is not supported, control of input stream is not supported
  Type of the ARP: ARPA, ARP Timeout 04:00
  Last entry of 00:00:00, 00:00:00 exit, exit hang never
  Last clearing of "show interface" counters 07:15:19
  Input queue: 0/75/0/0 (size/max/drops/dumps); Total output drops: 0
  Strategy of queues: fifo
  Output queue: 0/1024 (size/max)
  30 second entry rate 5911000 bps, 2439 packets/s
  exit rate of 30 seconds 14787000 bps, 2919 packets/s
  72815038 package, 3854388881 bytes, 0 no buffer entry
  Received 16169 broadcasts (5648 multicasts to IP)
  0 Runts, 0 giants, 0 shifters
       entry 46 errors, 0 CRC, 0 frame, invaded 46, 0 ignored
  Watchdog 0, multicast 16164, break 0 comments
  78723290 packets output, 1917039290 bytes, 0 underruns
  0 output errors, 0 collisions, 0 resets interface
  870 drops of unknown protocol
  0 babbles, collision end 0, 0 deferred
  carrier, 0 no carrier, lost 0 0 interrupt output
  output buffer, the output buffers 0 permuted 0 failures

  Yesterday was 1120 errors.

  In show processes cpu sound there is no cleats

  Hi you entered mistakes and cost overruns at the same time

  This means that your more using the interface, too inbound, buffers are filled and drops traffic when its maxed out

  It's Cisco response to exceedances

  In a small number of cases, the overrun counter can be incremented due to a software fault. However, in the majority of cases, it indicates that the capacity of the interface has been exceeded. Nothing can be done on the router that reports of cost overruns. If possible, the rate at which frames are to come should be controlled at the remote end of the connection. Otherwise, if the number of exceedances is high, the equipment must be upgraded.

• How to read Wireless Interface error

  I have a few questions about this error on the interface.

  (1) what could be the problem and the solution for the mistakes of this interface? I noticed that the number of output errors multiply.

  (2) why the number of errors is different from the interface of two?

  (3) how to know either the AP or external antennas is defective? This access point is a 1200 series.

  AP #sh int dot11Radio 0

  Dot11Radio0 is up, line protocol is up

  Material is 802.11 G Radio, the address is 1111.1111.1111 (bia 1212.1212.1212)

  MTU 1500 bytes, BW 54000 Kbit, DLY 1000 usec,

  reliability 255/255, txload 1/255, rxload 1/255

  Encapsulation 802. 1 q Virtual LAN, Vlan ID 1., loopback not set

  Type of the ARP: ARPA, ARP Timeout 04:00

  Last entry of 00:00:00, 00:00:00 exit, exit hang never

  Last clearing of "show interface" counters 17:19:47

  Input queue: 0/75/0/0 (size/max/drops/dumps); Total output drops: 7338

  Strategy of queues: fifo

  Output queue: 0/30 (size/max)

  5 minute input rate 5000 bps, 6 packets/sec

  5 minute output rate 243000 bits/s, 145 packets/s

  1034266 package, 1153540007 bytes, 6 no input buffer

  Received 6155 broadcasts, 0 Runts, 0 Giants 0 shifters

  entry 0, 0 CRC errors, frame 0, saturation 0, 0 ignored

  entry packets 0 with condition of dribble detected

  1171797 packets output, 443779394 bytes, 0 underruns

  449 output errors, 0 collisions, 0 resets interface

  0 babbles, collision end 0, 0 deferred

  0 lost carrier, 0 no carrier

  output buffer, the output buffers 0 permuted 0 failures

  AP #sh int dot11Radio 1

  Dot11Radio1 is up, line protocol is up

  The material is 802. 11A Radio, the address is 2222.2222.2222 (bia 2323.2323.2323)

  MTU 1500 bytes, BW 54000 Kbit, DLY 1000 usec,

  reliability 255/255, txload 2/255, rxload 1/255

  Encapsulation 802. 1 q Virtual LAN, Vlan ID 1., loopback not set

  Type of the ARP: ARPA, ARP Timeout 04:00

  Last entry of 00:00:00, 00:00:00 exit, exit hang never

  Last clearing of "show interface" counters 17:20:11

  Input queue: 0, 75, 2, 0 (size/max/drops/dumps); Total output drops: 7775

  Strategy of queues: fifo

  Output queue: 0/30 (size/max)

  5 minute input rate 3000 bps, 5 packets/s

  5 minute output rate 528000 bps, 144 packets/s

  241379 package, 35065157 bytes, 4 no input buffer

  Received 4941 broadcasts, 0 Runts, 0 Giants 0 shifters

  entry 0, 0 CRC errors, frame 0, saturation 0, 0 ignored

  entry packets 0 with condition of dribble detected

  686438 packets output, 149994557 bytes, 0 underruns

  291 output errors, 0 collisions, 0 resets interface

  0 babbles, collision end 0, 0 deferred

  0 lost carrier, 0 no carrier

  output buffer, the output buffers 0 permuted 0 failures

  Rare exceptions, errors always will... increase the key factor is "how (what sort of) errors," and "how long are they produced."

  It is a common process in troubleshooting to reset the counters (XXX clear interface counters) and analyze them for a period to determine the error rate (how fast the mistakes happen).

  You can also use this time to investigate whether counters increase because of some external actions (a Manager or some other iXdXiXoXtX standing in front of the antenna, for example).

  (2) you can activate one both antennas and measures on the ground with a laptop running Netstumbler (www.netstumbler.com , it's free) and compare the results of one antenna compared to another.

  Good luck

  Scott

• Link inside the declaration of nat in outermost interface ERROR

  Hi all

  I'm having a problem with my PIX501 w / "Cisco PIX Firewall Version 6.3 (4)", when ordering I get this caveat, is that normal? because it works perfectly fine in version 7.2 (2)...

  THE ERROR:

  PIX1 (config) # nat (outside) 1 222.127.244.52 255.255.255.252

  WARNING: Link inside the nat in outermost interface declaration.

  WARNING: Keyword 'outside' is probably missing.

  REFERENCE:

  # Sh nameif PIX1

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  In addition,

  Here is information on the 'outside' of the order PIX 6.3 setting

  outdoors

  If this interface is on a lower security interface that you identify by the corresponding overall statement, you must enter on the outside. This feature is called outside NAT or bidirectional NAT. Note from firewall PIX 6.3.2 source translation is performed before the translation of destination. For this reason, if the political source NAT allows the connection, the xlate will create, even if the traffic is denied by the policy of destination.

  Source:

  http://www.Cisco.com/en/us/docs/security/PIX/pix63/command/reference/Mr.html#wp1032129

  Don't forget to mark the answer as the correct answer or useful rate answers

  -Jouni

• component interface error

  Hello
  I am very new to CI.

  What are the reasons of error below.
  Component interface to get error handle. (18016

  It is for delivered THIS CI_PERSONAL_DATA

  
  

  Thank you

  Bharati.
  

  I think you're on the right track.

  You might want to focus on this piece of code. You can check if there is no data in PERS_DATA_USA this & sEmplid & sEffdt combination.

  & rsRowset = CreateRowset (Record.PERS_DATA_USA);

  & rsRowset.Fill (' WHERE EMPLID =: 1% AND EffDtCheck(PERS_DATA_USA,FILL,:2) ", & sEmplid, & sEffdt" ");

  & recRowset = & rsRowset (1). PERS_DATA_USA;

  & recRowset.GetField (Field.EMPLID). Value = & sEmplid;

  Also, check if the error occurs on the assistance of initialization or of education Open CI CI.

  / * create support * /.

  & ciHelper = create HR_CIPUSH:ciHelper (CompIntfc.CI_PERSONAL_DATA);

  OR

  / * Open, * /.

  If this is & ciHelper.ciOpen(&recRowset) then

  Return False;

  End - If;

• ODI Interface error

  Hi friends,
  
  
  When I run my interface,
  
  I get the error like below in inserting new record step and I'm under oracle control add km.
  
  Caused by: java.sql.SQLSyntaxErrorException: ORA-00904: "ABC_KEY": invalid identifier
  
  When I observed, when he created I$ table, it creates as tables as
  create table I$ _PQR
  (
  'ABC' NUMBER (10);
  )
  
  Because of the syntax to insert I $query also lik ebelwo
  Insert into I$ _pqr
  (
  'ABC '.
  
  )
  
  
  I understand this problem, it is Extra "" for the ABC column. But why this is happening like this and initially it worked fine. How to solve now.

  you have a space after ABC_KEY.
  You have to
  -Remove the database.
  -Return to the interface
  -Check the map.

• How do I see the lines not loaded by interface errors

  Hello, I have a simple interface, I'm loading of data within the same oracle database from one scheme to another scheme.
  But I see less 3 rows.
  Can some body please advice how to see lines that are not loaded, which justified etc..
  
  Thank you

  Hello

  You can also see in the ODI opening model--> right click on your target--> Check--> error data store...
  It shows you the E table $ table _ for this specific data store. For each rejected row, you can see all of the columns more the reason for the rejection.

  It will be useful,

  Jerome en

• interface error sunw.io.Serializable

  Hi all
  
  I use Jdeveloper 10.1.3.3.0.3 and still receive the following error in my control file when executing my page:
  
  "Error (71,41): incompatible types; found: class java.lang.String, required: interface of sunw.io.Serializable. »
  
  ------------------
  Control file:
  ------------------
  
  ' Public Sub processFormRequest (pageContext OAPageContext, OAWebBean webBean)
  {
  super.processFormRequest (pageContext, webBean);
  
  If (pageContext.getParameter ("HzPuiGoSearch")! = null)
  {
  
  String Numeroclient = pageContext.getParameter ("HzPuiCustomerNumber");
  OAApplicationModule am = pageContext.getApplicationModule (webBean);
  
  [Serializable] parameters = {Numeroclient}; Error line
  
  am.invokeMethod ("executeQuery", settings);
  }
  
  }
  
  ------------------
  File AMimpl:
  ------------------
  
  public void executeQuery (String Numeroclient)
  {
  
  VOD OAViewObject = (OAViewObject) getxxarSiteSearchVO1 ();
  vod.setWhereClauseParam (0, Numeroclient);
  vod.executeQuery ();
  }
  
  
  Thanks in advance!

  1 - Make sure you include "java.io.Serializable" as part of the package import yoru

  2. change the following line

  Of
  ---------
  [Serializable] parameters = {Numeroclient}

  TO
  -----
  [Serializable] parameters = new {Numeroclient} [Serializable]

  HTH,
  Maher

• Photoshop interface error

  Hello!

  I'm with this problem in my photoshop interface.

  the icons are larger and the menus as well.

  It is very aesthetic fact and unpleasant to work with.

  Anyone know how to fix this?

  I can't change the settings of software interface, but I think the problem is in windows.

  You must be using CC 2015 it has a bug, its default value of the scaling of the UI is AutoScaling showing 200% that it should not. Change the setting in preference to 100%

  

• Web interface error - could not contact the server at this time

  Hey all,.

  Immediately after completing the deployment of the new 2.1 UM I'm running an obstacle when connecting to the web interface. After authentication, with the web interface, I get the following when you select my user type (service provider or aggregator - anyone):

  

  I redeployed the VAPP twice is not a transient deployment problem. Networking seems fine - I can ping from areas on the Internet from the SUSE console. Not sure that this message refers on the 'server' is in contact with. It is deployed on ESXi 4.1 in a cluster vCentre vswitches standard, nothing special.

  Any ideas?

  Kind regards

  Daniel Whittaker.

  Daniel,

  When you get the message after installation, click OK and then refresh the page or click F5.  The message should appear is no longer.

  Kind regards

  David

• Interface a critical error: all stores data in a dataset must be attached

  Hi, I added the new data source store in the existing interface, and create the join between them, here's the code
  
  ITransactionStatus trans = odiInstance.getTransactionManager () .getTransaction (new DefaultTransactionDefinition());
  
  InteractiveInterfaceHelperWithActions helper = new InteractiveInterfaceHelperWithActions (odiInterface, odiInstance, odiInstance.getTransactionalEntityManager (), new SourceSetComputerRetainer (odiInterface), new SourceSetCreatorNew(), new SourceSetNameProviderBasicIncrement() new MappingPersistencePolicyDefault());
  
  OdiDataStore newDataStore = OdiUtils.getOdiDataStore (odiInstance, sourceTable, modelCode);
  
  helper.performAction (new InterfaceActionAddSourceDataStore (newDataStore, defaultDataset, new AliasComputerDoubleChecker(), new ClauseImporterLazy(), new AutoMappingComputerLazy()));
  
  String joinExpression = odiInterfaceVO.getPrimarySoruceDataStoreJoinColumn () + "=" + (attributeVO.getJoinColumn ()) replace ("@ALIAS @", alias);
  
  helper.performAction (new InterfaceActionOnJoinSetJoinProperties (new Join (defaultDataset, joinExpression, false, ExecutionLocation.SOURCE), false, true, false));
  
  If (helper.areSourceSetsDirty ()) {}
  helper.computeSourceSets ();
  }
  helper.preparePersist ();
  
  odiInstance.getTransactionalEntityManager () .persist (odiInterface);
  
  odiInstance.getTransactionManager () .commit (trans);
  
  When running helper.preparePersist (); I get following message.
  
  May 20, 2013 05:05:44 oracle.odi.interfaces.interactive.support.InteractiveInterfaceHelperWithActions preparePersist
  INFO: SDE_AGILE_AuditsFact.W_PLM_AUDIT_FS_SQ_W_PLM_QCR_PE a Interface error critical: all stores data in a dataset must be attached. This data set has several sets of storage of data source disconnected. The sets are: [W_PLM_QCR_PE]; [W_PLM_PAGE_THREE_PS]. To design a Cartesian product, create a join, and select cross in its properties join...
  
  y at - it no problem with the statement that I used for the join. After executing this code, when I see in the join of the interface are adequate.
  
  Thank you
  Nidhi

  You can use InterfaceActionAddJoin() instead and try.

  Join() constructor is for internal use only and should not be used. You can use InterfaceActionOnJoinSetJoinProperties.JoinType to join types.

• Check read the code 0000 T500 failed error even with a new hard drive

  Hello

  My T500 was slammed very hard one day, once I reboot, he worked for half an hour and gave up. I tested via the BIOS, he gave me code 0000 read failed error check.

  I presume that the HD is dead, inserted an a healthy Interior and works very well for a few hours and give up once again, tested by BIOS gave me the same error code.

  I was wondering what problem could be?

  best,

  Sy

  Yuanshi wrote:

  I presume that the HD is dead, inserted an a healthy Interior and works very well for a few hours and give up once again, tested by BIOS gave me the same error code.

  You can also prove that it is a SATA interface error by testing two hard drives in a box USB or Firewire. If you can live without portability, then perhaps this is also an option to use the T500 in the future.

• The logon User Interface DLL Masgina.dll failed to load?

  Hello

  My name is Shelley, I really honestly do nothing about computers and my computer at home, which is a dell with windows xp pro.   was working fine, then 1 morning I rose and ithad a blue screen with the message about it.

  The logon User Interface DLL msgina.dll failed to load.  Contact your system administrator to replace the DLL or restore the original DLL.         then she had a reset button to push.  When I pressed the button, the display cover Dell and then he showed the sreen of coverage of Microsoft Windows XP, then he can go right the message telling me that. The User Interface DLL failed.

  Now, my computer has been sitting there for 2 weeks, and no one can use it.  Now, I'm on my cell phone the school for 17 years.

  What should I take my computer in a store or is - something simple, maybe, I can do myself?

  OH and if you know, the computer is at my daughters school, they have gave to her, because she had really great classes and she's in schools IB program, so they gave him a computer to have at home, it is set up for academic use, I know not whether that counts or not.  She got a new laptop for Christmas. Other people in the House are now using the computer to play games and watch videos from YouTube.

  Can someone help me?   Thank you, Shelley

  Hello

  ·        You're able to boot in safe mode?

  ·        Remember to make changes to the system?

  Method 1:

  If you are able to boot into safe mode then I suggest to do a system restore to a previous point when the system worked very well and check.

  Step 1:

  I suggest to start in safe mode and check if the problem persists.

  a. restart the system and keep tapping F8 until you reach the start menu.

  b. Select safe mode from the list and press ENTER.

  Step 2:

  I suggest you do a system restore and check. Follow the steps mentioned in the article below.

  How to restore Windows XP to a previous state

  http://support.Microsoft.com/kb/306084

  I suggest you to consult the article below.

  "Logon user DLL Msgina.dll failed to load Interface" error after you have installed the MS04-003 security update

  http://support.Microsoft.com/kb/836683

  Thanks and regards.

  Thahaseena M
  Microsoft Answers Support Engineer.
  Visit ourMicrosoft answers feedback Forum and let us know what you think.