Interfaces (ASA 5520) cant ping
Hello
I recently implemented a configuration of active failover / standby with 2 secondary interfaces configured on my interface of g0/0 (g0/0.1 and g0/0.2) for some reason I can't an of these my ping test server (when the server is on the network and subnet to test the interface)? I'm not sure what continues... I've included a print out of my current configuration of the interface and failover. The test server is connected to a switch of 2724 Dell and the interfaces are in question.
interface GigabitEthernet0/0
No nameif
security-level 0
no ip address
!
interface GigabitEthernet0/0.1
VLAN 10
nameif Outside1
security-level 0
IP address 66.38.x.x 255.255.x.x Eve 66.38.x.x
!
interface GigabitEthernet0/0.2
VLAN 20
nameif Outside2
security-level 0
IP address 64.187.x.x 255.255.x.x Eve 64.187.x.x
!
interface GigabitEthernet0/1
nameif DMZ
security-level 100
IP address 255.255.x.x 10.10.x.x ensures 10.10.x.x
!
interface GigabitEthernet0/2
nameif private
security-level 40
IP address 255.255.x.x 192.168.x.x ensures 192.168.x.x
!
interface GigabitEthernet0/3
STATE/LAN failover Interface Description
!
interface Management0/0
STATE failover Interface Description
No nameif
security-level 100
IP address 192.168.x.x 255.255.x.x
!
clock timezone IS - 5
clock to summer time EDT recurring
pager lines 24
Enable logging
monitor debug logging
asdm of logging of information
MTU 1500 Outside1
MTU 1500 Outside2
MTU 1500 DMZ
MTU 1500 private
failover
primary failover lan unit
local failover FoInt GigabitEthernet0/3 network interface
failover replication http
link failover FoInt GigabitEthernet0/3
failover interface ip FoInt 192.168.x.x 255.255.x.x Eve 192.168.x.x
the interface of the monitor Outside1
the interface of the monitor Outside2
Thank you
Chris
Hi Chris,
Your config subinterface is fine, except that you will probably need to affect the level of safety that is different between them unless you have already planned for this.
Normally, it is on the side of the switch that must be configured accordingly. The link of the trunk between the firewall and the switch use the encapsulation DOT1Q (IEEE). I don't know if he Dell support. Make sure that the trunk permits some Vlan you assigned to the firewall secondary interfaces.
To be able to ping to the interface, make sure that you allow the firewall to allow/permit icmp to hit the interface using the command "icmp", for example "icmp allow any Outside2."
BTW, what is the gateway for your server? Is it subinterface ASA (function vlan) or IP VLAN on the switch?
Other, you must apply normal static ACL, NAT firewall and so on.
Rgds,
AK
Tags: Cisco Security
Similar Questions
-
Cisco ASA 5520 cannot ping between VPN Tunnels
I have the main site and sites A and B. A to connect to the hand and B connects to the main. I can ping from A hand and has for main. I can ping from main to B and B to main. However, I can not ping from A to B. A and B are sonicwall 2040 and main is a 5520. The question should not be with the 5520 none allowing traffic between the two VPN Tunnels, but I can't understand why it does not work. Can someone give an idea on that? Thanks in advance.
Hello
I see that you use ASDM. Always makes my eyes bleed when I need to look at the DM_INLINE of named objects and try to make sense the CLI format
Seems to me that there are problems with the NAT.
If you don't mind a small break between the main Site and remote locations, I'd say changing some follows the NAT configuration
Remove old
no nat source (indoor, outdoor) public static DM_INLINE_NETWORK_9 DM_INLINE_NETWORK_9 DM_INLINE_NETWORK_10 DM_INLINE_NETWORK_10 non-proxy-arp-search of route static destination
no nat source (indoor, outdoor) public static DM_INLINE_NETWORK_11 DM_INLINE_NETWORK_11 DM_INLINE_NETWORK_12 DM_INLINE_NETWORK_12 non-proxy-arp-search of route static destination
Add a new
object-group network NETWORK-2790
object-network 10.217.0.0 255.255.255.0
object-network 10.217.1.0 255.255.255.0
object-group network NETWORK-3820
object-network 10.216.0.0 255.255.255.0
object-network 10.216.1.0 255.255.255.0
object-group network NETWORK-COLO
object-net 10.8.0.0 255.255.255.0
destination of NETWORK of NETWORK-2790-2790 static NAT (outside, outside) static source NETWORK - 3820 - 3820
NAT static destination of NETWORK of NETWORK-COLO-COLO (indoor, outdoor) static source NETWORK - 2790 - 2790
NAT static destination of NETWORK of NETWORK-COLO-COLO (indoor, outdoor) static source NETWORK - 3820 - 3820
The first new line of configuring NAT manages the NAT0 configuration for traffic between SiteA and SiteB. The following configurations of NAT 2 manage the NAT0 for traffic between the main Site - hand Site SiteA - SiteB
-Jouni
-
9.1 ASA 2 drops PING (icmp codes 0 &; 8)
Hello
Im trying to ping DMZ on ASA to interface to the host from the INSIDE and vice versa. It does not work :( Trying to debug icmp however the icmp packet did not even touch the DMZ interface for the particular host. Doing so with packet - trace ASA displays all results under ALLOW. We could explain to me how to allow a host placed in X interface for PING Y interface itself?
Thank you very much in advance!
NB.
The result of packet - trace is attached. What I'm trying to do, it's to ping interface DMZ (192.168.200.1) of the host from the INSIDE (192.168.100.10).
Works as expected. The ASA does not support the rattling a foreign address. If your ping-host is located inside the interface, you can only ping the inside IP, if your ping-host is located in the demilitarized zone, you only can ping the DMZ IP. The ASA handles differently then a router.
The only exception is with the 'management-access XXX' command when the ping goes through a tunnel.
-
Tunnel VPN ASA 5520 (DMZ + INSIDE) destined for OUTSIDE
I can't find any reference to anywhere else.
We have an ASA 5520 to our site HQ (inside the network) with several regional subnets on the DMZ interface.
We need connectivity VPN Site to Site between the INSIDE and a remote control on the OUTSIDE of the site, as well as between the DMZ subnets and even outside the site. The interface from the OUTSIDE of the SAA must be local VPN endpoint for all tunnels.
I created a S2S VPN between the INSIDE and the OUTSIDE site and it works great.
When I create a VPN S2S tunnel between a site of DMZ and even outside the site (using the same settings the and remote, but with a cryptomap different because the local subnet (DMZ) is different from the other inside the subnet, the traffic gets the mapping (show crypto isakmp his) to the same cryptomap that was created for the access to the tunnel from the OUTSIDE) , instead of to the new cryptomap, so remote endpoint deletes it, and traffic also causes SPI incorrect of for the remote endpoint, which makes the original INTERIOR outside OF THE VPN tunnel to fall from time to time.
Is this a bug?
I also did a local S2S VPN tunnel configuration test of networks as everything INSIDE and the DMZ. With the help of the wizard VPN S2S leads ASA only to create a NAT rule exempted for the subnet on the INSIDE interface. Can I manually create another tax-exempt NAT rule to the side of the DMZ and use this a S2S tunnel to connect sites inside and DMZ to the remote OFF-SITE in a connection profile?
I'm building a Rube Goldberg?
Thank you
George
Hi George,.
It seems you have a situation overlapping it, are you sure that subnets inside did not overlap with the networks from the DMZ? A package tracer could clarify wha that the ASA is actually sending.
In addition, you can merge the two interfaces on the same card encryption if you wish, just make sure that the NAT is configured correctly. For example; Source NAT (all, outside) static...
It may be useful
-Randy-
-
VPN site to site &; outdoor on ASA 5520 VPN client
Hi, I'm jonathan rivero.
I have an ASA 5520 Version 8.0 (2), I configured the site-to-site VPN and works very well, in the other device, I configured the VPN Client for remote users and works very well, but I try to cofigure 2 VPNs on ASA 5520 on the same outside interface and I have the line "outside_map interface card crypto outdoors (for VPN client). , but when I set up the "crypto map VPNL2L outside interface, it replaces the command', and so I can have only a single connection.
the executed show.
ASA1 (config) # sh run
: Saved
:
ASA Version 8.0 (2)
!
hostname ASA1
activate 7esAUjZmKQSFDCZX encrypted password
names of
!
interface Ethernet0/0
nameif inside
security-level 100
address 172.16.3.2 IP 255.255.255.0
!
interface Ethernet0/1
nameif outside
security-level 0
IP 200.20.20.1 255.255.255.0
!
interface Ethernet0/1.1
VLAN 1
nameif outside1
security-level 0
no ip address
!
interface Ethernet0/2
Shutdown
No nameif
no level of security
no ip address
!
interface Ethernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface Ethernet0/4
Shutdown
No nameif
no level of security
no ip address
!
interface Ethernet0/5
Shutdown
No nameif
no level of security
no ip address
!
2KFQnbNIdI.2KYOU encrypted passwd
passive FTP mode
object-group, net-LAN
object-network 172.16.0.0 255.255.255.0
object-network 172.16.1.0 255.255.255.0
object-network 172.16.2.0 255.255.255.0
object-network 172.16.3.0 255.255.255.0
object-group, NET / remote
object-network 172.16.100.0 255.255.255.0
object-network 172.16.101.0 255.255.255.0
object-network 172.16.102.0 255.255.255.0
object-network 172.16.103.0 255.255.255.0
object-group network net-poolvpn
object-network 192.168.11.0 255.255.255.0
access list outside nat extended permit ip net local group object all
access-list extended sheep allowed ip local object-group net object-group net / remote
access-list extended sheep allowed ip local object-group net net poolvpn object-group
access-list splittun-vpngroup1 extended permitted ip local object-group net net poolvpn object-group
pager lines 24
Within 1500 MTU
Outside 1500 MTU
outside1 MTU 1500
IP local pool ippool 192.168.11.1 - 192.168.11.100 mask 255.255.255.0
no failover
ICMP unreachable rate-limit 100 burst-size 10
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0 access-list sheep
NAT (inside) 1 access list outside nat
Route outside 0.0.0.0 0.0.0.0 200.20.20.1 1
Route inside 172.16.0.0 255.255.255.0 172.16.3.2 1
Route inside 172.16.1.0 255.255.255.0 172.16.3.2 1
Route inside 172.16.2.0 255.255.255.0 172.16.3.2 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout, uauth 0:05:00 absolute
dynamic-access-policy-registration DfltAccessPolicy
the ssh LOCAL console AAA authentication
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
86400 seconds, duration of life crypto ipsec security association
Crypto ipsec kilobytes of life security-association 400000
Crypto-map dynamic outside_dyn_map 20 the value transform-set ESP-3DES-SHA
card crypto VPNL2L 1 match for sheep
card crypto VPNL2L 1 set peer 200.30.30.1
VPNL2L 1 transform-set ESP-3DES-MD5 crypto card game
map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map
outside_map interface card crypto outside
crypto isakmp identity address
crypto ISAKMP allow outside
crypto ISAKMP policy 20
preshared authentication
3des encryption
md5 hash
Group 2
life 86400
crypto ISAKMP policy 30
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
crypto ISAKMP policy 65535
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH timeout 5
Console timeout 0
a basic threat threat detection
Statistics-list of access threat detection
!
!
internal vpngroup1 group policy
attributes of the strategy of group vpngroup1
banner value +++ welcome to Cisco Systems 7.0. +++
value of 192.168.0.1 DNS server 192.168.1.1
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value splittun-vpngroup1
value by default-ad domain - domain.local
Split-dns value ad - domain.local
the address value ippool pools
username password asa1 VRTlLlJ48/PoDKjS encrypted privilege 15
tunnel-group 200.30.30.1 type ipsec-l2l
IPSec-attributes tunnel-group 200.30.30.1
pre-shared-key *.
type tunnel-group vpngroup1 remote access
tunnel-group vpngroup1 General-attributes
ippool address pool
Group Policy - by default-vpngroup1
vpngroup1 group of tunnel ipsec-attributes
pre-shared-key *.
context of prompt hostname
Cryptochecksum:00000000000000000000000000000000
: end
ASA2 (config) #sh run
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
86400 seconds, duration of life crypto ipsec security association
Crypto ipsec kilobytes of life security-association 400000
card crypto VPNL2L 1 match for sheep
card crypto VPNL2L 1 set peer 200.30.30.1
VPNL2L 1 transform-set ESP-3DES-MD5 crypto card game
VPNL2L interface card crypto outside
crypto isakmp identity address
crypto ISAKMP allow outside
crypto ISAKMP policy 20
preshared authentication
3des encryption
md5 hash
Group 2
life 86400tunnel-group 200.30.30.1 type ipsec-l2l
IPSec-attributes tunnel-group 200.30.30.1
pre-shared key ciscomy topology:
I try with the following links, but did not work
http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a0080912cfd.shtml
http://www.Cisco.com/en/us/products/ps6120/products_tech_note09186a00807e0aca.shtml
Best regards...
"" I thing both the force of the SAA with the new road outside, why is that? ".
without the road ASA pushes traffic inward, by default.
In any case, this must have been a learning experience.
Hopefully, this has been no help.
Please rate, all the helful post.
Thank you
Rizwan Muhammed.
-
Hi I have a Cisco Asa 5520 and I want to vpn site-to-site by using another interface with a carrier of lan to lan, the problem is when I try to pass traffic have the syslog error to follow:
No translation not found for udp src lan2lan:10.5.50.63/44437 dst colo: biggiesmalls groups / 897LAN to LAN service interface is called: lan2lan
one of the internal interfaces is called: colo
I think that is problem with Nat on the SAA but I need help with this.Config:!
interface GigabitEthernet0/0
nameif outside
security-level 0
eve of fw - ext 255.255.255.0 address IP XXaaaNNaa
OSPF cost 10
OSPF network point-to-point non-broadcast
!
interface GigabitEthernet0/1
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/1.50
VLAN 50
nameif lb
security-level 20
IP 10.1.50.11 255.255.255.0
OSPF cost 10
!
interface GigabitEthernet0/1,501
VLAN 501
nameif colo
security-level 90
eve of fw - int 255.255.255.0 172.16.2.253 IP address
OSPF cost 10
!
!
interface GigabitEthernet1/1
Door-Lan2Lan description
nameif lan2lan
security-level 0
IP 10.100.50.1 255.255.255.248
!
access extensive list ip 10.1.0.0 lan2lan_cryptomap_51 allow 255.255.0.0 object-group elo
permit access list extended ip sfnet 255.255.255.0 lan2lan_cryptomap_51 object-group elo
pager lines 24
Enable logging
host colo biggiesmalls record
No message logging 313001
External MTU 1500
MTU 1500 lb
MTU 1500 Colo
lan2lan MTU 1500
ICMP unreachable rate-limit 1 burst-size 1
ARP timeout 14400
NAT-control
Global 1 interface (external)
interface of global (lb) 1
Global (colo) 1 interface
NAT (lb) 1 10.1.50.0 255.255.255.0
NAT (colo) - access list 0 colo_nat0_outbound
NAT (colo) 1 10.1.13.0 255.255.255.0
NAT (colo) 1 10.1.16.0 255.255.255.0
NAT (colo) 1 0.0.0.0 0.0.0.0
external_access_in access to the external interface group
Access-group lb_access_in in lb interface
Access-group colo_access_in in interface colo
Access-group management_access_in in management of the interface
Access-group interface lan2lan lan2lan
!
Service resetoutside
card crypto match 51 lan2lan_map address lan2lan_cryptomap_51
lan2lan_map 51 crypto map set peer 10.100.50.2
card crypto lan2lan_map 51 game of transformation-ESP-3DES-SHA
crypto lan2lan_map 51 set reverse-road map
lan2lan_map interface lan2lan crypto card
quit smoking
ISAKMP crypto identity hostname
ISAKMP crypto enable lan2lan
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Crypto isakmp nat-traversal 20
enable client-implementation to date
IPSec-attributes tunnel-group DefaultL2LGroup
pre-shared-key xxXnnAA
tunnel-group 10.100.50.2 type ipsec-l2l
tunnel-group 10.100.50.2 General-attributes
Group Policy - by default-site2site
No vpn-addr-assign aaa
No dhcp vpn-addr-assign
Telnet timeout 5
!The VPN is OK? ("' isakmp crypto to show his" should show a MM_Active tunnel to the peer address ")
Normally exempt us VPN site-to-site of NAT traffic. This could be your problem. If you can share your configuration, we can have a look.
p.s. you should affect the question of the security / VPN forum.
-
With an ASA 5520 port forwarding
Hi all
I recently bought a Cisco ASA 5520 on eBay for study and I decided to only use it as a firewall between my home LAN and Internet. Wow, what a learning curve! I managed to add my internal networks as objects and create a rule (thanks to youtube) NAT to PAT my internal devices out of the Internet with ASSISTANT Deputy Ministers, but I am really struggling to do the following:-
-allow all incoming traffic that hits the outside interface for port 38921 and nat at 10.1.10.101:38921
-allow all incoming traffic that hits the outside interface for port 30392 and nat at 10.1.10.101:30392
Can someone guide me on how to do it, because I have a couple of services that run behind these ports on a server I want to get when I'm not at home? My (rather messy) config is as follows:-
hostname FW1
activate the encrypted password
encrypted passwd
names of
!
interface GigabitEthernet0/0
Description * externally facing Internet *.
nameif outside
security-level 0
IP address dhcp setroute
!
interface GigabitEthernet0/1
Description * internal face to 3750 *.
nameif inside
security-level 100
IP 10.1.10.2 255.255.255.0
!
interface GigabitEthernet0/2
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
nameif management
security-level 100
IP 192.168.1.1 255.255.255.0
!
passive FTP mode
the VLAN1 object network
subnet 192.168.1.0 255.255.255.0
Legacy description
network of the WiredLAN object
10.1.10.0 subnet 255.255.255.0
Wired LAN description
network of the CorporateWifi object
10.1.160.0 subnet 255.255.255.0
Company Description 160 of VLAN wireless
network of the GuestWifi object
10.1.165.0 subnet 255.255.255.0
Description Wireless VLAN 165 comments
network of the LegacyLAN object
subnet 192.168.1.0 255.255.255.0
Description Legacy LAN in place until the change on
the file server object network
Home 10.1.10.101
Description File Server
service object Service1
tcp source eq eq 38921 38921 destination service
1 service Description
the All_Inside_Networks object-group network
network-object VLAN1
network-object, object WiredLAN
network-object, object CorporateWifi
network-object, object GuestWifi
network-object, object LegacyLAN
object-group service Service2 tcp - udp
port-object eq 30392
object-group service DM_INLINE_TCPUDP_1 tcp - udp
port-object eq 30392
Group-object Service2
object-group Protocol TCPUDP
object-protocol udp
object-tcp protocol
Outside_access_in list extended access allowed object-group TCPUDP any inactive FileServer object-group DM_INLINE_TCPUDP_1 object
Outside_access_in list extended access allowed object Service1 any inactive FileServer object
pager lines 24
Enable logging
asdm of logging of information
Outside 1500 MTU
MTU 1500 internal
management of MTU 1500
no failover
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 714.bin
don't allow no asdm history
ARP timeout 14400
service interface NAT (inside, outside) dynamic source FileServer Service1 inactive Service1
NAT (all, outside) interface dynamic source All_Inside_Networks
Access-group Outside_access_in in interface outside
Internal route 10.1.160.0 255.255.255.0 10.1.10.1 1
Internal route 10.1.165.0 255.255.255.0 10.1.10.1 1
Internal route 192.168.1.0 255.255.255.0 10.1.10.1 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
Enable http server
http 10.1.160.15 255.255.255.255 internal
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
Telnet 10.1.160.15 255.255.255.255 internal
Telnet timeout 5
SSH timeout 5
Console timeout 0
interface ID client DHCP-client to the outside
management of 192.168.1.2 - dhcpd address 192.168.1.254
enable dhcpd management
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
username privilege of encrypted password of Barry 15
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:19be38edefe8c3fd05e720aedee62c8e
: end
1. This is just one example of configuration and another option with to reason and avoid to send us the complete configuration of NAT:
network of the 10.1.10.101 object
Home 10.1.10.101
service object 38921
tcp source eq 38921 service
service object 30392
tcp source eq 30392 service
NAT (inside, outside) 1 static source 10.1.10.101 38921 38921 service interface
NAT (inside, outside) 1 static source 10.1.10.101 30392 30392 service interface
Let me know if it works
-
Hi all. In our company we have recently upgraded our PIX 515 firewall to ASA 5520, and we started to live a thing strange event. On one of the sites we host, I saw a lot of outdated SSM messages popping up and I think that they are the source of the problem when they surf the site (mainly surfing works fine, but sometimes people cannot content etc.).
I found the Cisco solution for this problem by using the MPF, but one thing confuses me. If I ask a MPF allowing adults MSS on the external interface of the ASA does this political conflict with the comprehensive policy that is on the SAA by default or can they both at the same time?
Thanks in advance for any help.
You can have a single policy per interface and another - global, that by default applies to default-inspection-traffic.
See http://www.cisco.com/en/US/docs/security/asa/asa80/configuration/guide/mpc.html for more details.
-
Using Cisco Client to site VPN on a behind a NAT ASA 5520
I apologize if this has been asked and we answered in the forums. I looked, and while I found a large number of entries that were dancing all around this question, I never found nothing which addressed this specific issue. We currently use an ASA 5520 as the head end of a relatively large customer to site IPSEC VPN (approximately 240 users, not consecutively). This ASA is currently sitting behind a Checkpoint firewall with a real publicly addressable IP address on its public interface. All of our customers use the legacy Cisco VPN (not the one anyconnect) client. We plan to a few controllers F5 link set up between ISPS and firewalls. For VPN connectivity F5 recommends that we NAT IP address (called a broad IP) to point back to a private IP address on the ASA and F5. My question is, will this work? I've always heard say that the head of line needed to have a public IP address on this subject because this is what will be placed in packages for the client to respond to.
For further information, here's what we have now and what we are invited to attend.
Current
ISP - router - firewall-fire - ASA (public IP address as endpoint)
Proposed
ISP - router - F5 (public IP address as endpoint using a NAT to ASA) - Firewall - ASA (10.X.X.X as its external interface)
Proposed alternative
ISP - router - F5 (public IP address as endpoint using a NAT to ASA) - ASA (10.X.X.X as its external interface)
All thoughts at this moment would be greatly appreciated. Thank you!
Hello
If there is a static NAT one by one on F5 to the external interface of the ASA, then I don't think they would be any problems.
Because when the client will attempt to connect to IKE to the translated public IP, F5 will redirect the request to ASA outside interface that is configured for the VPN.In addition, to ensure the udp500, 4500 and esp is allowed and then you should be good to go.
HTH
Concerning
Mohit -
ASA 5520 - SSL VPN (Anyconnect) licenses
Hello
Can someone clarify for me the SSL VPN/AnyConnect for the ASA 5520 license? Specifically, the differences between the AnyConnect Essentials and AnyConnect Premium. Our current license looks like this:
The devices allowed for this platform:
The maximum physical Interfaces: unlimited
VLAN maximum: 150
Internal hosts: unlimited
Failover: Active/active
VPN - A: enabled
VPN-3DES-AES: enabled
Security contexts: 2
GTP/GPRS: disabled
SSL VPN peers: 2
Total of the VPN peers: 750
Sharing license: disabled
AnyConnect for Mobile: disabled
AnyConnect Cisco VPN phone: disabled
AnyConnect Essentials: disabled
Assessment of Advanced endpoint: disabled
Proxy sessions for the UC phone: 2
Total number of Sessions of Proxy UC: 2
Botnet traffic filter: disabledThis platform includes an ASA 5520 VPN Plus license.
I guess that means that we have just the 2 'free trial' SSL VPN licenses and nothing else.
I would like to add 25 or maybe 50 SSL VPN licenses and be able to use a combination of full free client, thin client and groups client AnyConnect. The 'ASA5500-SSL-25' (or 50) would be the correct license I need to buy?
Thank you
Rob
Hello
The essentials license is per device and does not allow full-tunnel.
If you need other features like Secure Desktop, without client SSL and other optional features such as shared licenses, you must go to the Premium license.
Federico.
-
VPN site to Site with ASA 5520 * please help *.
I am using two ASA 5520, and try to put up a site to site VPN. This seems to be pretty simple, but I'm on my third day of train this is up and running. Both 5520's are running the latest 9.1 (5) IOS.
Please note: I replaced it with [#1-WAN IP] and [#2-WAN IP] for WAN IP of the ASA addresses.
Thanks in advance for any help you may have.
-------------------------------------------------------------------------------------------------------------------------------------------------
ASA 5520 # 1:
Crypto ikev1 allow outside
the local object of net network
10.0.0.0 subnet 255.255.255.0net remote object network
172.20.0.0 subnet 255.255.255.0outside_1_cryptomap list of allowed ip object local net net access / remote
tunnel-group [IP #2-WAN] type ipsec-l2l
IPSec-attributes tunnel-group [#2-WAN IP]
pre-shared-key cisco123IKEv1 crypto policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
card crypto oustide_map 1 match address outside_1_cryptomap
card crypto oustide_map 1 set transform-set ESP-3DES-SHA ikev1
card crypto outside_map 1 set pfs Group1
map 1 set outside_map crypto peer [#2-WAN IP]
outside_map interface card crypto outsideNAT (inside, outside) 1 local static source net net-local destination static remote net net / remote
-------------------------------------------------------------------------------------------------------------------------------------------------
ASA 5520 #2:
Crypto ikev1 allow outside
the local object of net network
172.20.0.0 subnet 255.255.255.0net remote object network
10.0.0.0 subnet 255.255.255.0outside_1_cryptomap list of allowed ip object local net net access / remote
tunnel-group [#1-WAN IP] type ipsec-l2l
IPSec-attributes tunnel-group [#1-WAN IP]
pre-shared-key cisco123IKEv1 crypto policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
card crypto oustide_map 1 match address outside_1_cryptomap
card crypto oustide_map 1 set transform-set ESP-3DES-SHA ikev1
card crypto outside_map 1 set pfs Group1
map 1 set outside_map crypto peer [#1-WAN IP]
outside_map interface card crypto outsideNAT (inside, outside) 1 local static source net net-local destination static remote net net / remote
Try to correct the mistakes in the two configs.
In some places, you have 'oustide_map' where you need "outside_map".
-
Installation of ASA EasyVPN - cannot ping loopback on router CME
Hello
I don't know if it is a problem of firewall or something on my router, so I thought I would start here. I have an ASA 5505 at home that I use as a client for the purpose of connecting a Cisco IP phone to a CME No. 2851 router EasyVPN. At the office, I have an ASA 5510, which acts as the EasyVPN server. The CME router loopback address is 10.1.254.254, and the router's ethernet interfaces are 10.2.100.50 and 10.1.100.1. The customer EasyVPN receives an address 192.168.100.1 the EasyVPN server.
In my house, if I connect a computer to my ASA 5505 VPN is based and I can ping all my hosts interns (at the office), and I can ping both interfaces of the router. If I try to ping the router loopback address I get nothing. If I start the router and work my way to the EasyVPN (ASA 5510) Server I can ping the loopback address of the router to the power switch and then the ASA5510. I think it's a problem of firewall because of the capture, I install both inside the ASA interfaces:
If I ping 10.2.100.50 or 10.1.100.1, I see the echo and echo on the ASA5505 responses, and I see them on the ASA5510 - successfully running through the VPN tunnel.
If I ping 10.1.254.254, I see the echo to the ASA5505 request, but I don't see anything on the ASA5510.
I checked my nat_exemption on the ASA5510 and I have an entry like this:
nat_exemption list of allowed ip extended access any 192.168.100.0 255.255.255.128
I can provide more if necessary configs, but anybody have any ideas where I'm wrong?
Thanks in advance,
Brandon
Brandon,
I would like to start showing us "crypto ipsec to show its" on your home 5505.
Then the station we would need:
--------
See the establishment of performance-crypto
See running nat setting
See the global race
See the static race
See the tunnel-group race
---------
Ideally I would allow newspapers on informqtional level on headboard and ASA local.
Run the ping command and check:
-------
Show logg. I have 10.1.254.254
-------
We are looking for connections being built or any "deny" messages.
Marcin
-
I set up a VPN site-to site between a Cisco ISR 1841 and a Cisco ASA 5520, everything seems to work but I have a few questions.
1. I must explicitly authorize all VPN traffic in the ACL on the external interface of the 1841, y at - it an equivalent of router "vpn sysopt connection permit?
2. Although the VPN rises and pass traffic, I have the opportunity to see what follows?
* 14:11:52.883 22 June: % CRYPTO-6-IKMP_MODE_FAILURE: fast processing mode has failed with the peer 1.1.1.1
You can share the outputs full? Both sides at the same time?
Bottom line, I don't think it's normal in IOS 12.4 mainline unless packages are leaking clear ;/
-
ASA 5520: Support GVRP?
Hello
I'm trying to configure the secondary interfaces on an ASA 5520. I have a Dell switch that I will be endearing to which only supports GARP VLAN registration Protocol (GVRP). I was just wondering if it is possible for me to pass circuits to GVRP on my ASA policy?
Thank you
Chris
This switch is capable of 802. 1 q trunking. The Dell switch that I think what you have to do is create a trunk on port port, you have your ASA connected to and set them VLAN appropriate which can be labeled on this port. On the ASA to create a subset of the interfaces and to each interface in the appropriate VLAN.
E.G.
interface GigabitEthernet0/2.1
VLAN 12
interface GigabitEthernet0/2.2
VLAN 31
I think that the limitation is 64 VLANS.
-
Multiple DMZ on ASA 5520 connection to a Catalyst 3550
I have ASA 5520 with 4 ports, I have 8 networks from the DMZ. As anyone configure an ASA 5520 for use with VLANS or sous-interfaces? How are you?
I plan to use interfaces on the DMZ interface and assign a vlan to each interface of void. Should I configure dot1q trunking on the interface of the DMZ. If this isn't the case, I'll have to set it up on the switchport to my DMZ switch? or does each subinterface * Just Thinking out loud *.
Thank you
Hi there on the physical interface first you won't have any config except for nonstop and up.then interface create secondary interfaces on the same interface as int I0.1. set the security level and assign them to one vlan and IP to make them.after which connect a switchport port and configure the port a port trucnking cause all traffic vlan of the asa will elapse of this port.on the button to connect your servers and assign the port to their VLAN respective and configure gateways thie as the ip address of the vlan configured on the asa. That's all. Incase you need more information. write again. If I solved it your problem then pls note the post.
Assane
Maybe you are looking for
-
Firefox does not open Windows - intermittent - 10 pro
Once I click on the icon to launch the Firefox browser I momentarily have the little blue icon of waiting... then nothing.I can use everything on the computer, including the border, IE, Chrome, and Safari. If I go to Task Manager it shows Firefox wit
-
iPhone IMEI number 6 stolen necessary
6 iPhone stolen from my former employer. Without box or invoices. And the various countries of the company to contact. All possible means to get the IMEI number to use to locate the iphone app for the police?
-
Satellite L755: What is the sound plinking from my HARD drive?
I just bought the L755 and had only 3 days. It has a weird plinking from the HD. There isn't any rhythm to it, it's very random. Any ideas?
-
OTP-S3700 how to dis - connect on the internet...
Just bought a BDP-S3700. Connected to my connection Wireless for the program installation and update of the firmware. How can I connect dice - my wireless if I don't want to use streaming services?
-
Hi friends, Well, I want to buy a laptop computer in a few days, but I am confused that one should I take. As I read on the net and found several brand laptop these hp, lenovo, dell, toshiba CAREB and amazing design. In fact, I got bored with my offi