Using Cisco Client to site VPN on a behind a NAT ASA 5520
I apologize if this has been asked and we answered in the forums. I looked, and while I found a large number of entries that were dancing all around this question, I never found nothing which addressed this specific issue. We currently use an ASA 5520 as the head end of a relatively large customer to site IPSEC VPN (approximately 240 users, not consecutively). This ASA is currently sitting behind a Checkpoint firewall with a real publicly addressable IP address on its public interface. All of our customers use the legacy Cisco VPN (not the one anyconnect) client. We plan to a few controllers F5 link set up between ISPS and firewalls. For VPN connectivity F5 recommends that we NAT IP address (called a broad IP) to point back to a private IP address on the ASA and F5. My question is, will this work? I've always heard say that the head of line needed to have a public IP address on this subject because this is what will be placed in packages for the client to respond to.
For further information, here's what we have now and what we are invited to attend.
Current
ISP - router - firewall-fire - ASA (public IP address as endpoint)
Proposed
ISP - router - F5 (public IP address as endpoint using a NAT to ASA) - Firewall - ASA (10.X.X.X as its external interface)
Proposed alternative
ISP - router - F5 (public IP address as endpoint using a NAT to ASA) - ASA (10.X.X.X as its external interface)
All thoughts at this moment would be greatly appreciated. Thank you!
Hello
If there is a static NAT one by one on F5 to the external interface of the ASA, then I don't think they would be any problems.
Because when the client will attempt to connect to IKE to the translated public IP, F5 will redirect the request to ASA outside interface that is configured for the VPN.
In addition, to ensure the udp500, 4500 and esp is allowed and then you should be good to go.
HTH
Concerning
Mohit
Tags: Cisco Security
Similar Questions
-
Using Cisco Client remote access
Hello
This is part of my config from site to site, which works very well.
crypto ISAKMP policy 1
BA 3des
preshared authentication
Group 2
address of cisco key crypto isakmp 0.0.0.0 0.0.0.0 no.-xauth
ISAKMP crypto keepalive 20BUT when I applied client config in the light of the foregoing, the customer remote access may not work
Configuration group customer isakmp crypto-customer
key cisco123
DNS 165.21.83.88
pool POOL_1
ACL 101BUT if I remove "No.-xauth" in my site to isakmp, then my client may work but my site to site VPN may not work. Please advise, what is the problem? OR how can I fix this?
address of cisco key crypto isakmp 0.0.0.0 0.0.0.0
Thank you
VTI will never work because you have a dynamic ip address.
Please follow the sample configuration provided above for dynamic to static IPSec VPN:
http://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_configuration_example09186a00801dddbb.shtml
-
Hi all
I need a big favor, I configured a cisco 1841 for a VPN Client-to-site, but I can't get a connection with a client of Linux (Ubuntu). I don't understand where is the problem if on the router or the customer. Now I have reported setting up, is there anybody can check whether or not it is fair? Thank you very much for your support.
The plan of the network is the following
REMOTE LAN (192.168.1.0/24) <->ROUTER-A (X.X.X.X) <->VPN <->SOHO NETWORKING <->CLIENT UBUNTU (192.168.2.1/24)
and the Conference is the following
username username password 0 USER12345
!
crypto ISAKMP policy 3
BA 3des-md5 hash
preshared authentication
Group 2
!
ISAKMP crypto client configuration group to remote vpn client
banner ^ C * you are connected to the IOS router with VPN Client-to-Site * ^ C
key 54321
netmask 255.255.255.0
masociete.com field
remote control-vpn-pool
10 Max-users
Max-connections 10
ACL 150
!
Crypto ipsec transform-set VPN - SET esp-3des esp-md5-hmac
!
Crypto-map dynamic dynmap 10
Description * Client to users VPN Site *.
transformation-VPN-SET game
market arriere-route
!
map clientmap 65535-isakmp ipsec crypto dynamic dynmap
!
interface FastEthernet0/0
Description * ROUTER - has--> LAN *.
IP 192.168.1.254 255.255.255.0
IP nat inside
IP virtual-reassembly
automatic duplex
automatic speed
No keepalive
!
interface Serial0/0/0
no ip address
frame relay IETF encapsulation
event logging subif-link-status
dlci-change of status event logging
IP access-group 103 to
load-interval 30
no fair queue
frame-relay lmi-type ansi
!
point-to-point interface Serial0/0/0.1
Description * ROUTER - has--> WAN *.
address IP X.X.X.X 255.255.255.252
NAT outside IP
IP virtual-reassembly
SNMP trap-the link status
No cdp enable
No frame relay frames arp
interface-dlci 100 IETF
clientmap card crypto
!
Local IP 192.168.1.1 to remote vpn-pool pool 192.168.1.10
!
IP route 0.0.0.0 0.0.0.0 Serial0/0/0.1
!
IP nat inside source map route VPN - NAT interface overloading Serial0/0/0.1
!
Access-list 100 * ACL NAT note *.
access-list 100 deny ip 10.10.10.0 0.0.0.255 192.168.1.0 0.0.0.255
access-list 100 permit ip 10.10.10.0 0.0.0.255 any
!
Note access-list 103 * OPEN THE PORTS for SSH/TELNET SERVICES ON THE ROUTER *.
access list 103 permit tcp any any eq 22
access list 103 permit tcp any any eq telnet
access list 103 permit tcp any any eq 443
Note access-list 103 *.
Note access-list 103 * CLOSE THE PORTS to BLOCK THE REST OF THE ACCESS *.
access-list 103 deny ip any any newspaper
Note access-list 103 *.
!
Note access-list 150 * ACL VPN SITE-to-SITE *.
access-list 150 permit ip 10.10.10.0 0.0.0.255 192.168.1.0 0.0.0.255
Note access-list 150 *.
!
route VPN - NAT allowed 10 map
corresponds to the IP 100
I think that the configuration is correct, but there is no need to specify a subnet mask to "crypto isakmp configuration group to remote vpn client." customer In addition, you must change your 103 ACL. Add the following statements before refusing:
permit udp and host X.X.X.X eq 500
permit udp and host X.X.X.X eq 4500
esp permits and host X.X.X.X
---
HTH. Please rate this post if this has been helpful. If it solves your problem, please mark this message as "right answer".
-
Unable to connect to the client to site VPN
Hello
Suddenly this morning I couldn't connect to the VPN from my work. I did not update the operating system or any other application in my Mac. I checked with my VPN provider and all is well. I tried to connect to the VPN from another PC and the connection was successful.
It of weird, can you help me on this?
Thank you
My Info:
OS X El Capitan
Version 10.11.6 (15-1004)
Error log:
7 September 11:17:57 racoon Gerards-MacBook-Pro [680]: agreed to the takeover of vpn connection.
7 September 11:17:57 racoon Gerards-MacBook-Pro [680]: IPSec to connect to the server 50.57.56.150
7 September 11:17:57 racoon Gerards-MacBook-Pro [680]: connection.
7 September 11:17:57 racoon Gerards-MacBook-Pro [680]: IPSec Phase 1 started (initiated by me).
7 September 11:17:57 racoon Gerards-MacBook-Pro [680]: IKE Packet: forward the success. (Initiator, Aggressive Mode 1 message).
7 September 11:17:57 racoon Gerards-MacBook-Pro [680]: > > > > > status of phase change = Phase 1 began by us
7 September 11:17:57 racoon Gerards-MacBook-Pro [680]: no message must be encrypted, 0x14a1, side 0 status
7 September 11:17:57 racoon Gerards-MacBook-Pro [680]: IPSec to connect to the server 50.57.56.150
7 September 11:17:57 racoon Gerards-MacBook-Pro [680]: connection.
7 September 11:17:57 racoon Gerards-MacBook-Pro [680]: IPSec Phase 1 started (initiated by me).
7 September 11:17:57 racoon Gerards-MacBook-Pro [680]: IKE Packet: forward the success. (Initiator, Aggressive Mode 1 message).
7 September 11:17:57 racoon Gerards-MacBook-Pro [680]: > > > > > status of phase change = Phase 1 began by us
7 September 11:17:57 racoon Gerards-MacBook-Pro [680]: port 62465 anticipated, but 0
7 September 11:17:57 racoon Gerards-MacBook-Pro [680]: IKEv1 Phase 1 AUTH: success. (Initiator, aggressive-Mode Message 2).
7 September 11:17:57 racoon Gerards-MacBook-Pro [680]: > > > > > status of phase change = Phase 1 began with a peer
7 September 11:17:57 racoon Gerards-MacBook-Pro [680]: IKE Packet: receive a success. (Initiator, Aggressive Mode 2 message).
7 September 11:17:57 racoon Gerards-MacBook-Pro [680]: initiating IKEv1 Phase 1: success. (Initiator, aggressive Mode).
7 September 11:17:57 racoon Gerards-MacBook-Pro [680]: IKE Packet: forward the success. (Initiator, Aggressive Mode 3 message).
7 September 11:17:57 racoon Gerards-MacBook-Pro [680]: IPSec Phase 1 established (initiated by me).
7 September 11:18:05 racoon Gerards-MacBook-Pro [680]!: jumped to retransmit the frags: frag_flags 1, r-> sendbuf-> l 136, max 1280
7 September 11:18:05 racoon Gerards-MacBook-Pro [680]: retransmitted packet received from the 50.57.56.150 [500].
7 September 11:18:05 racoon Gerards-MacBook-Pro [680]: the packet is retransmitted by 50.57.56.150 [500].
7 September 11:18:13 racoon Gerards-MacBook-Pro [680]!: jumped to retransmit the frags: frag_flags 1, r-> sendbuf-> l 136, max 1280
7 September 11:18:13 racoon Gerards-MacBook-Pro [680]: retransmitted packet received from the 50.57.56.150 [500].
7 September 11:18:13 racoon Gerards-MacBook-Pro [680]: the packet is retransmitted by 50.57.56.150 [500].
7 September 11:18:21 racoon Gerards-MacBook-Pro [680]!: jumped to retransmit the frags: frag_flags 1, r-> sendbuf-> l 136, max 1280
7 September 11:18:21 racoon Gerards-MacBook-Pro [680]: retransmitted packet received from the 50.57.56.150 [500].
7 September 11:18:21 racoon Gerards-MacBook-Pro [680]: the packet is retransmitted by 50.57.56.150 [500].
7 September 11:18:27 racoon Gerards-MacBook-Pro [680]: IPSec disconnection from the server 50.57.56.150
7 September 11:18:27 racoon Gerards-MacBook-Pro [680]: IKE Packet: forward the success. (Information message).
7 September 11:18:27 racoon Gerards-MacBook-Pro [680]: IKEv1-Information Notice: pass success. (Delete the ISAKMP Security Association).
7 September 11:18:27 racoon Gerards-MacBook-Pro [680]: glob found no match for the path "/ var/run/racoon/*.conf".
7 September 11:18:27 racoon Gerards-MacBook-Pro [680]: IPSec disconnection from the server 50.57.56.150
September 7 11:18:27 Gerards-MacBook-Pro UserNotificationCenter [682]: * ATTENTION: the method in the class userSpaceScaleFactor NSWindow is discouraged on 10.7 and later versions. It should not be used in new applications. Use convertRectToBacking: instead.
7 September 11:18:29 racoon Gerards-MacBook-Pro [680]: connection.
7 September 11:18:29 racoon Gerards-MacBook-Pro [680]: unknown information exchange has received.
-
Site to site VPN upward but not pass traffic (ASA 5505 8.3.1 and 9.2.3 version)
Hello
I'll put up a tunnel vpn site-to-site between two locations. Both have cisco ASA 5505 running a different version, I'll explain in more detail below. so far, I was able to get the tunnel to come but I can't seem to pass traffic, I work at this for days now and have not been able to understand why he will not pass traffic. Needless to say that the customer's PO would be on the fact that their VPN is not upward and they had to do by hand. I'll put the configs below, if possible can someone help me as soon as POSSIBLE, I really want to get this site up and running so that we do not lose the customer.
An IP address of 0.0.0.0 = site
Site B IP = 1.1.1.1A Version of the site = 8.3.1
Version of the site B = 9.2.3__________________________
_________A RACE OF THE SITE CONFIGURATION
Output of the command: "sh run".
: Saved
:
ASA Version 8.3 (1)
!
hostname SDMCLNASA01
SDMCLNASA01 domain name. LOCAL
Select 5E8js/Fs7qxjxWdp of encrypted password
2KFQnbNIdI.2KYOU encrypted passwd
names of
!
interface Vlan1
nameif inside
security-level 100
the IP 192.168.0.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
the IP 0.0.0.0 255.255.255.252
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
passive FTP mode
clock timezone CST - 6
clock to summer time recurring CDT
DNS lookup field inside
DNS domain-lookup outside
DNS server-group DefaultDNS
SDMCLNASA01 domain name. LOCAL
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
network of the NETWORK_OBJ_192.168.0.0_24 object
192.168.0.0 subnet 255.255.255.0
network of the NETWORK_OBJ_192.168.1.0_24 object
subnet 192.168.1.0 255.255.255.0
network lan_internal object
192.168.0.0 subnet 255.255.255.0
purpose of the smtp network
Home 192.168.0.245
Network http object
Home 192.168.0.245
rdp network object
Home 192.168.0.245
network ssl object
Home 192.168.0.245
network camera_1 object
host 192.168.0.13
network camerahttp object
host 192.168.0.13
service object 8081
source eq 8081 destination eq 8081 tcp service
Dvr description
network camera-http object
host 192.168.0.13
network dvr-http object
host 192.168.0.13
network dvr-mediaport object
host 192.168.0.13
object-group Protocol DM_INLINE_PROTOCOL_1
object-protocol udp
object-tcp protocol
object-group Protocol TCPUDP
object-protocol udp
object-tcp protocol
DM_INLINE_TCP_1 tcp service object-group
EQ port 3389 object
port-object eq www
EQ object of the https port
EQ smtp port object
DM_INLINE_TCP_2 tcp service object-group
port-object eq 34567
port-object eq 34599
EQ port 8081 object
permit access ip 192.168.0.0 scope list outside_1_cryptomap 255.255.255.0 192.168.1.0 255.255.255.0
outside_access_in list extended access permit tcp any any eq smtp
outside_access_in list extended access permit tcp any any DM_INLINE_TCP_1 object-group
outside_access_in list extended access permit tcp any any DM_INLINE_TCP_2 object-group
permit access ip 192.168.0.0 scope list inside_nat0_outbound 255.255.255.0 192.168.1.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
ICMP unreachable rate-limit 1 burst-size 1
ICMP allow any inside
ICMP allow all outside
don't allow no asdm history
ARP timeout 14400
NAT (inside, outside) static static source NETWORK_OBJ_192.168.1.0_24 destination NETWORK_OBJ_192.168.0.0_24 NETWORK_OBJ_192.168.0.0_24 NETWORK_OBJ_192.168.1.0_24
NAT (exterior, Interior) static static source NETWORK_OBJ_192.168.0.0_24 destination NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.0.0_24
!
network lan_internal object
NAT dynamic interface (indoor, outdoor)
purpose of the smtp network
NAT (all, outside) interface static tcp smtp smtp service
Network http object
NAT (all, outside) interface static tcp www www service
rdp network object
NAT (all, outside) interface static service tcp 3389 3389
network ssl object
NAT (all, outside) interface static tcp https https service
network dvr-http object
NAT (all, outside) interface static 8081 8081 tcp service
network dvr-mediaport object
NAT (all, outside) interface static 34567 34567 tcp service
Access-group outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 71.42.194.209 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
http server enable 8080
http 192.168.0.0 255.255.255.0 inside
http 192.168.1.0 255.255.255.0 inside
http 192.168.1.0 255.255.255.0 outside
http 71.40.221.136 255.255.255.252 inside
http 71.40.221.136 255.255.255.252 outside
http 192.168.0.0 255.255.255.0 outside
http 97.79.197.42 255.255.255.255 inside
http 97.79.197.42 255.255.255.255 outside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
card crypto outside_map 1 match address outside_1_cryptomap
card crypto outside_map 1 set peer 1.1.1.1
card crypto outside_map 1 set of transformation-ESP-3DES-SHA
outside_map interface card crypto outside
crypto isakmp identity address
crypto ISAKMP allow outside
crypto ISAKMP policy 65535
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH timeout 5
Console timeout 0
dhcpd address 192.168.0.50 - 192.168.0.150 inside
dhcpd dns 192.168.0.245 209.18.47.62 interface inside
dhcpd SDMCLNASA01 field. LOCAL inside interface
dhcpd allow inside
!a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
attributes of Group Policy DfltGrpPolicy
Protocol-tunnel-VPN IPSec l2tp ipsec
tunnel-group 1.1.1.1 type ipsec-l2l
tunnel-group 1.1.1.1 ipsec-attributes
pre-shared key *.
!
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
!
context of prompt hostname
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:462428c25e9748896e98863f2d8aeee7
: end________________________________
SITE B RUNNING CONFIG
Output of the command: "sh run".
: Saved
:
: Serial number: JMX1635Z1BV
: Material: ASA5505, 512 MB RAM, 500 MHz Geode Processor
:
ASA Version 9.2 (3)
!
ciscoasa hostname
activate qddbwnZVxqYXToV9 encrypted password
volatile xlate deny tcp any4 any4
volatile xlate deny tcp any4 any6
volatile xlate deny tcp any6 any4
volatile xlate deny tcp any6 any6
volatile xlate deny udp any4 any4 eq field
volatile xlate deny udp any4 any6 eq field
volatile xlate deny udp any6 any4 eq field
volatile xlate deny udp any6 any6 eq field
names of
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.1.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP 1.1.1.1 255.255.255.252
!
passive FTP mode
clock timezone CST - 6
clock to summer time recurring CDT
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
network camera_http object
host 192.168.1.13
network camera_media object
host 192.168.1.13
network of the NETWORK_OBJ_192.168.0.0_24 object
192.168.0.0 subnet 255.255.255.0
network of the NETWORK_OBJ_192.168.1.0_24 object
subnet 192.168.1.0 255.255.255.0
outside_access_in list extended access permit tcp any any eq 9000
outside_access_in list extended access permit tcp any any eq www
outside_access_in list extended access permit icmp any one
outside_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 object NETWORK_OBJ_192.168.0.0_24
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
no failover
ICMP unreachable rate-limit 1 burst-size 1
ICMP allow any inside
ICMP allow all outside
ASDM image disk0: / asdm - 732.bin
don't allow no asdm history
ARP timeout 14400
no permit-nonconnected arp
NAT (inside, outside) static static source NETWORK_OBJ_192.168.0.0_24 destination NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.0.0_24
NAT (exterior, Interior) static static source NETWORK_OBJ_192.168.1.0_24 destination NETWORK_OBJ_192.168.0.0_24 NETWORK_OBJ_192.168.0.0_24 NETWORK_OBJ_192.168.1.0_24
!
network camera_http object
NAT (all, outside) interface static tcp www www service
network camera_media object
NAT (all, outside) interface static 9000 9000 tcp service
!
NAT source auto after (indoor, outdoor) dynamic one interface
Access-group outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 71.40.221.137 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
Enable http server
http 192.168.1.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
Crypto ipsec ikev2 AES256 ipsec-proposal
Protocol esp encryption aes-256
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES192
Protocol esp encryption aes-192
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES
Esp aes encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 proposal ipsec 3DES
Esp 3des encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal OF
encryption protocol esp
Esp integrity sha - 1, md5 Protocol
Crypto ipsec pmtu aging infinite - the security association
card crypto outside_map 1 match address outside_cryptomap
card crypto outside_map 1 peer set 0.0.0.0
card crypto outside_map 1 set transform-set ESP-3DES-SHA ikev1
outside_map interface card crypto outside
trustpool crypto ca policy
IKEv2 crypto policy 1
aes-256 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 10
aes-192 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 20
aes encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 30
3des encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 40
the Encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
Crypto ikev1 allow outside
IKEv1 crypto policy 120
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH stricthostkeycheck
SSH timeout 5
SSH group dh-Group1-sha1 key exchange
Console timeout 0dhcpd address 192.168.1.50 - 192.168.1.150 inside
dhcpd dns 192.168.0.245 209.18.47.61 interface inside
dhcpd SDPHARR field. LOCAL inside interface
dhcpd allow inside
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
AnyConnect essentials
attributes of Group Policy DfltGrpPolicy
Ikev1 VPN-tunnel-Protocol
internal GroupPolicy_0.0.0.0 group strategy
attributes of Group Policy GroupPolicy_0.0.0.0
VPN-tunnel-Protocol ikev1, ikev2
tunnel-group 0.0.0.0 type ipsec-l2l
tunnel-group 0.0.0.0 ipsec-attributes
IKEv1 pre-shared-key *.
remote control-IKEv2 pre-shared-key authentication *.
pre-shared-key authentication local IKEv2 *.
!
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
!
context of prompt hostname
no remote anonymous reporting call
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:19031ab1e3bae21d7cc8319fb7ecf0eb
: endSorry my mistake.
Delete this if it's still there
card crypto external_map 1 the value reverse-road
Add this to both sides
card crypto outside_map 1 the value reverse-road
Sorry about that.
Mike
-
How to control the activity of the client-to-site (IPSEC ASA)
I have a client to site VPN configuration on my 5505 according to directives of the Chapter35 of the ASA8.x configuration guide.
One thing I am not sure about is how can I control what VPN users can connect to? I see nothing in the config that binds inside the interface so that prevents them to connect to the DMZ as well? How to limit connectivity so they can only connect to a host on the inside? or a host on the inside and the other on the DMZ?
Thank you
According to me, is what you're looking for.
It will be useful.
-
What VPN work as a PPTP vpn firewall CISCO-ASA-5520.
Hi all
Can you please tell me which replace the VPN I can configure PPTP on ASA 5520 firewall. What VPN work as a PPTP vpn firewall CISCO-ASA-5520.
You can use the wizard VPN of RA with ASDM and confiugre L2TP IPSEC VPN that does not need a VPN Client must be installed.
Michael
Please note all useful posts
-
Site to Site VPN working without Crypto Card (ASA 8.2 (1))
Hi all
Find a strange situation on our firewall to ASA5540:
We have a few Site to Site VPN and also activate on the ASA VPN cleint, all are working properly. But finding that a VPN from Site to Site is running without crypto map configuration. Is this possible?
I tried to erase isa his and claire ipsec his then VPN came once again. Tested too, it's the ping requests to a remote site through the VPN.
I saw there are config tunnel-group for VPN but saw no card crypto and ACL.
How is the firewall knows what traffic should be encrypted for this VPN tunnel without crypto card?
This is the bug?
Thanks in advance,
It can be an easy vpn configuration.
Could you post output config operation remove any sensitive information. This could help us answer your question more specifically.
-
IPSec site to site VPN cisco VPN client routing problem and
Hello
I'm really stuck with the configuration of ipsec site to site vpn (hub to spoke, multiple rays) with cisco vpn remote client access to this vpn.
The problem is with remote access - cisco vpn client access - I can communicate with hub lan - but I need also communication of all lans speaks of the cisco vpn client.
There are on the shelves, there is no material used cisco - routers DLINK.
Someone told me that it is possible to use NAT to translate remote access IP-lan-HUB customers and thus allow communication - but I'm unable to set up and operate.
Can someone help me please?
Thank you
Peter
RAYS - not cisco devices / another provider
Cisco 1841 HSEC HUB:
crypto ISAKMP policy 1
BA 3des
preshared authentication
Group 2
ISAKMP crypto key x xx address no.-xauth
!
the group x crypto isakmp client configuration
x key
pool vpnclientpool
ACL 190
include-local-lan
!
86400 seconds, duration of life crypto ipsec security association
Crypto ipsec transform-set esp-3des esp-sha-hmac 1cisco
!
Crypto-map dynamic dynmap 10
Set transform-set 1cisco
!
card crypto ETH0 client authentication list userauthen
card crypto isakmp authorization list groupauthor ETH0
client configuration address card crypto ETH0 answer
ETH0 1 ipsec-isakmp crypto map
set peer x
Set transform-set 1cisco
PFS group2 Set
match address 180
card ETH0 10-isakmp ipsec crypto dynamic dynmap
!
!
interface FastEthernet0/1
Description $ES_WAN$
card crypto ETH0
!
IP local pool vpnclientpool 192.168.200.100 192.168.200.150
!
!
overload of IP nat inside source list LOCAL interface FastEthernet0/1
!
IP access-list extended LOCAL
deny ip 192.168.7.0 0.0.0.255 192.168.1.0 0.0.0.255
deny ip 192.168.7.0 0.0.0.255 192.168.200.0 0.0.0.255
IP 192.168.7.0 allow 0.0.0.255 any
!
access-list 180 allow ip 192.168.7.0 0.0.0.255 192.168.1.0 0.0.0.255
access-list 190 allow ip 192.168.7.0 0.0.0.255 192.168.200.0 0.0.0.255
!
How the DLINK has been configured for traffic between the site to site VPN subnets? You are able to add multiple remote subnets on DLINK? If you can, then you must add the pool of Client VPN subnet.
Alternatively, if you cannot add multiple subnet on DLINK router, you can change the pool of Client VPN 192.168.6.0/24, and on the crypto ACL between the site to site VPN, you must edit the 180 existing ACL
DE:
access-list 180 allow ip 192.168.7.0 0.0.0.255 192.168.1.0 0.0.0.255
access-list 180 allow ip 192.168.200.0 0.0.0.255 192.168.1.0 0.0.0.255
TO:
access-list 180 allow ip 192.168.6.0 0.0.1.255 192.168.1.0 0.0.0.255
Also change the ACL 190 split tunnel:
DE:
access-list 190 allow ip 192.168.7.0 0.0.0.255 192.168.200.0 0.0.0.255
access-list 190 allow ip 192.168.1.0 0.0.0.255 192.168.200.0 0.0.0.255
TO:
access-list 190 allow ip 192.168.7.0 0.0.0.255 192.168.6.0 0.0.0.255
access-list 190 allow ip 192.168.1.0 0.0.0.255 192.168.6.0 0.0.0.255
Finally, replace the remote subnet 192.168.7.0/255.255.255.0 192.168.6.0/255.255.254.0 DLINK.
Hope that helps.
-
Unable to connect to the Cisco VPN you use native client: El Capitan
I'm unable to connect to the Cisco VPN using native client server Cisco OSX via IPSec. Before the upgrade for connections VPN El Capitan has worked without any problems. VPN uses the shared secret of group. It seems, I get the error "raccoon [2580] ': could not send message vpn_control: Broken pipe ' during the connection."
When I upgraded to El Capitan, VPN connection has stopped working. I tried to do the following:
* connect using the old work VPN connection: without success
Config: Hand [server address, account name],
AUTH settings [shared secret, the Group name].
Advanced [mode to use the passive FTP = TRUE]
errors:
"authd [124]: copy_rights: _server_authorize failed.
"raccoon [2580]: could not send message vpn_control: Broken pipe"
...
* Add new VPN connection using L2TP over IPSec: without success
Config: Hand [server address, account name],
Authentication settings [user authentication: password, identification of the Machine: Shared Secret].
Advanced [send all traffic on the VPN = TRUE]
errsors:
"pppd [2616]: password not found in the system keychain.
"authd [124]: copy_rights: _server_authorize failed.
...
* Add new connection using Cisco via IPSec VPN: without success
Main config: [server address, account name].
AUTH settings [shared secret, the Group name].
Advanced [mode to use the passive FTP = TRUE]
errors:
"authd [124]: copy_rights: _server_authorize failed.
"raccoon [2580]: could not send message vpn_control: Broken pipe"
VPN server is high and does not work and accepts connections, this problem is entirely on the client side.
I. Journal of Console app existing/Legacy VPN connection:
26/03/16 10:24:01, 000 syslogd [40]: sender ASL statistics
26/03/16 10:24:01, nesessionmanager 311 [2112]: NESMLegacySession [VPN_CONN_NAME$: B7816CCC-2D2C-4D6D - 83 D 9-B2C8B6EB8589]: received an order to start SystemUIServer [2346]
26/03/16 10:24:01, nesessionmanager 311 [2112]: NESMLegacySession [VPN_CONN_NAME$: B7816CCC-2D2C-4D6D - 83 D 9-B2C8B6EB8589]: changed to connecting status
26/03/16 10:24:01, nesessionmanager 313 [2112]: IPSec to connect to the server $VPN_SERVER_IP
26/03/16 10:24:01, 316 nesessionmanager [2112]: phase 1 of the IPSec from.
26/03/16 10:24:01, racoon 338 [2580]: agreed to the takeover of vpn connection.
26/03/16 10:24:01, racoon 338 [2580]: agreed to the takeover of vpn connection.
26/03/16 10:24:01, racoon 339 [2580]: IPSec to connect to the server $VPN_SERVER_IP
26/03/16 10:24:01, racoon 339 [2580]: IPSec to connect to the server $VPN_SERVER_IP
26/03/16 10:24:01, racoon 339 [2580]: connection.
26/03/16 10:24:01, racoon 339 [2580]: IPSec Phase 1 started (initiated by me).
26/03/16 10:24:01, racoon 339 [2580]: IPSec Phase 1 started (initiated by me).
26/03/16 10:24:01, racoon 349 [2580]: IKE Packet: forward the success. (Initiator, Aggressive Mode 1 message).
26/03/16 10:24:01, racoon 350 [2580]: > > > > > status of phase change = Phase 1 began by us
26/03/16 10:24:01, racoon 350 [2580]: > > > > > status of phase change = Phase 1 began by us
26/03/16 10:24:01, racoon 381 [2580]: no message must be encrypted, 0x14a1, side 0 status
26/03/16 10:24:01, racoon 381 [2580]: no message must be encrypted, 0x14a1, side 0 status
26/03/16 10:24:01, 381 nesessionmanager [2112]: Controller IPSec: IKE FAILED. phase 2, assert 0
26/03/16 10:24:01, 381 nesessionmanager [2112]: Controller IPSec: retry the aggressive mode IPSec with DH group 2
26/03/16 10:24:01, nesessionmanager 404 [2112]: phase 1 of the IPSec from.
26/03/16 10:24:01, racoon 404 [2580]: IPSec to connect to the server $VPN_SERVER_IP
26/03/16 10:24:01, racoon 404 [2580]: IPSec to connect to the server $VPN_SERVER_IP
26/03/16 10:24:01, racoon 405 [2580]: connection.
26/03/16 10:24:01, racoon 405 [2580]: IPSec Phase 1 started (initiated by me).
26/03/16 10:24:01, racoon 405 [2580]: IPSec Phase 1 started (initiated by me).
26/03/16 10:24:01, 407 raccoon [2580]: IKE Packet: forward the success. (Initiator, Aggressive Mode 1 message).
26/03/16 10:24:01, 407 raccoon [2580]: > > > > > status of phase change = Phase 1 began by us
26/03/16 10:24:01, 407 raccoon [2580]: > > > > > status of phase change = Phase 1 began by us
26/03/16 10:24:01, racoon 436 [2580]: port 62465 anticipated, but 0
26/03/16 10:24:01, racoon 436 [2580]: port 62465 anticipated, but 0
26/03/16 10:24:01, 463 raccoon [2580]: IKEv1 Phase 1 AUTH: success. (Initiator, aggressive-Mode Message 2).
26/03/16 10:24:01, 463 raccoon [2580]: > > > > > status of phase change = Phase 1 began with a peer
26/03/16 10:24:01, 463 raccoon [2580]: > > > > > status of phase change = Phase 1 began with a peer
26/03/16 10:24:01, 463 raccoon [2580]: IKE Packet: receive a success. (Initiator, Aggressive Mode 2 message).
26/03/16 10:24:01, 463 raccoon [2580]: initiating IKEv1 Phase 1: success. (Initiator, aggressive Mode).
26/03/16 10:24:01, 463 raccoon [2580]: IKE Packet: forward the success. (Initiator, Aggressive Mode 3 message).
26/03/16 10:24:01, 463 raccoon [2580]: IPSec Phase 1 established (initiated by me).
26/03/16 10:24:01, 463 raccoon [2580]: IPSec Phase 1 established (initiated by me).
26/03/16 10:24:01, 484 raccoon [2580]: IPSec Extended requested authentication.
26/03/16 10:24:01, 484 raccoon [2580]: IPSec Extended requested authentication.
26/03/16 10:24:01, nesessionmanager 485 [2112]: IPSec asking extended authentication.
[26/03/16 10:24:01, 494 nesessionmanager [2112]: NESMLegacySession[$VPN-CONN-NAME:B7816CCC-2D2C-4D6D-83D9-B2C8B6EB8589]: status changed by disconnecting
26/03/16 10:24:01, 495 nesessionmanager [2112]: IPSec disconnection from the server $VPN_SERVER_IP
26/03/16 10:24:01, racoon 495 [2580]: IPSec disconnection from the server $VPN_SERVER_IP
26/03/16 10:24:01, racoon 495 [2580]: IPSec disconnection from the server $VPN_SERVER_IP
26/03/16 10:24:01, racoon 495 [2580]: IKE Packet: forward the success. (Information message).
26/03/16 10:24:01, racoon 495 [2580]: IKEv1-Information Notice: pass success. (Delete the ISAKMP Security Association).
26/03/16 10:24:01, racoon 495 [2580]: could not send message vpn_control: Broken pipe
26/03/16 10:24:01, racoon 495 [2580]: could not send message vpn_control: Broken pipe
[26/03/16 10:24:01, 496 nesessionmanager [2112]: NESMLegacySession[$VPN-CONN-NAME:B7816CCC-2D2C-4D6D-83D9-B2C8B6EB8589]: status changed to offline, last stop reason no
26/03/16 10:24:01, racoon 496 [2580]: glob found no match for the path "/ var/run/racoon/*.conf".
26/03/16 10:24:01, racoon 496 [2580]: glob found no match for the path "/ var/run/racoon/*.conf".
26/03/16 10:24:01, racoon 496 [2580]: IPSec disconnection from the server $VPN_SERVER_IP
26/03/16 10:24:01, racoon 496 [2580]: IPSec disconnection from the server $VPN_SERVER_IP
$VPN_SERVER_IP
II. new VPN connection using L2TP over IPSec Console app log:
26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextSetFillColorWithColor: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextSetStrokeColorWithColor: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextGetCompositeOperation: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextSetCompositeOperation: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextFillRects: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextSetCompositeOperation: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextClipToRect: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextGetShouldSmoothFonts: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextGetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextGetFontAntialiasingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetDefaultUserSpaceToDeviceSpaceTransform: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextConcatCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextDrawImages: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetShouldSmoothFonts: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetDefaultUserSpaceToDeviceSpaceTransform: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, com.apple.preference.network.remoteservice [2539 295]: CGContextConcatCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextDrawImages: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetDefaultUserSpaceToDeviceSpaceTransform: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, com.apple.preference.network.remoteservice [2539 295]: CGContextConcatCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextDrawImages: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:28, [2539 339] com.apple.preference.network.remoteservice: error in CoreDragRemoveTrackingHandler:-1856
26/03/16 10:37:28, [2539 339] com.apple.preference.network.remoteservice: error in CoreDragRemoveReceiveHandler:-1856
26/03/16 10:37:28, com.apple.xpc.launchd [1 393]: (com.apple.SystemUIServer.agent [2346]) Service was released due to the signal: Broken pipe: 13
26/03/16 10:37:28, Spotlight 461 [459]: spot: logging agent
26/03/16 10:37:28, [2539 487] com.apple.preference.network.remoteservice: service - area of the one error ERROR = NEConfigurationErrorDomain Code = 9 "configuration is unchanged" UserInfo = {NSLocalizedDescription = configuration is unchanged}
26/03/16 10:37:28, [2539 487] com.apple.preference.network.remoteservice: service - area of the one error ERROR = NEConfigurationErrorDomain Code = 9 "configuration is unchanged" UserInfo = {NSLocalizedDescription = configuration is unchanged}
26/03/16 10:37:28, nesessionmanager 519 [2112]: NESMLegacySession [VPN_CONN_NAME$: 04c 10954-16 b 2 - 40BB - B3F1 - 9288F968029E]: received an order to start com.apple.preference.network.re [2539]
26/03/16 10:37:28, nesessionmanager 519 [2112]: NESMLegacySession [VPN_CONN_NAME$: 04c 10954-16 b 2 - 40BB - B3F1 - 9288F968029E]: changed to connecting status
26/03/16 10:37:28, com.apple.SecurityServer [75 536]: rules of problem opening the file "/ etc/authorization ': no such file or directory
26/03/16 10:37:28, com.apple.SecurityServer [75 536]: sandbox has denied authorizing the right "system.keychain.modify" customer "/ usr/libexec/nehelper" [184]
26/03/16 10:37:28, 536 pppd [2616]: NetworkExtension is the controller
26/03/16 10:37:28, 538 pppd [2616]: NetworkExtension is the controller
26/03/16 10:37:28, nehelper 540 [184]: 10954-16 b 2 - 40BB - B3F1 04c - 9288F968029E: cannot copy content, returned SecKeychainItemCopyContent user interaction is not allowed.
26/03/16 10:37:28, nehelper 540 [184]: 10954-16 b 2 - 40BB - B3F1 04c - 9288F968029E: SecKeychainItemFreeContent returned the user interaction is not allowed.
26/03/16 10:37:28, 570 pppd [2616]: password not found in the system keychain
26/03/16 10:37:28, 572 pppd [2616]: publish_entry SCDSet() failed: success!
26/03/16 10:37:28, 573 pppd [2616]: publish_entry SCDSet() failed: success!
26/03/16 10:37:28, 573 pppd [2616]: pppd 2.4.2 (Apple version 809.40.5) started by $VPN_SERVER_USER, uid 501
26/03/16 10:37:28, SystemUIServer 620 [2615]: [BluetoothHIDDeviceController] EventServiceConnectedCallback
26/03/16 10:37:28, SystemUIServer 620 [2615]: [BluetoothHIDDeviceController] EventServiceDisconnectedCallback
26/03/16 10:37:28, authd 720 [124]: copy_rights: _server_authorize failed
26/03/16 10:37:28, sandboxd 748 [120]: nehelper (184) ([184]) refuse the authorization-right-get system.keychain.modify
III. New connection of Cisco VPN through IPSec Console app log:
26/03/16 10:18:26, 917 WindowServer [172]: _CGXRemoveWindowFromWindowMovementGroup: 0x10d of window is not attached to the window 0x10f
26/03/16 10:19:43, 975 WindowServer [172]: _CGXRemoveWindowFromWindowMovementGroup: 0x10d of window is not attached to the window 0x10f
[26/03/16 10:19:56 nesessionmanager 265 [2112]: NESMLegacySession[$VPN-CONN-NAME:72874CC0-2A89-4B61-80F1-9BB4F3EA953B]: received an order to start SystemUIServer [2346]
[26/03/16 10:19:56 nesessionmanager 265 [2112]: NESMLegacySession[$VPN-CONN-NAME:72874CC0-2A89-4B61-80F1-9BB4F3EA953B]: changed to connecting status
26/03/16 10:19:56, nesessionmanager 267 [2112]: IPSec to connect to the server $VPN_SERVER_IP
26/03/16 10:19:56, nesessionmanager 270 [2112]: phase 1 of the IPSec from.
26/03/16 10:19:56, authd 284 [124]: copy_rights: _server_authorize failed
26/03/16 10:19:56, 295 raccoon [2576]: agreed to the takeover of vpn connection.
26/03/16 10:19:56, 295 raccoon [2576]: agreed to the takeover of vpn connection.
26/03/16 10:19:56, 295 raccoon [2576]: IPSec to connect to the server $VPN_SERVER_IP
26/03/16 10:19:56, 295 raccoon [2576]: IPSec to connect to the server $VPN_SERVER_IP
26/03/16 10:19:56, racoon 296 [2576]: connection.
26/03/16 10:19:56, racoon 296 [2576]: IPSec Phase 1 started (initiated by me).
26/03/16 10:19:56, racoon 296 [2576]: IPSec Phase 1 started (initiated by me).
26/03/16 10:19:56, racoon 308 [2576]: IKE Packet: forward the success. (Initiator, Aggressive Mode 1 message).
26/03/16 10:19:56, racoon 308 [2576]: > > > > > status of phase change = Phase 1 began by us
26/03/16 10:19:56, racoon 308 [2576]: > > > > > status of phase change = Phase 1 began by us
26/03/16 10:19:56, 352 raccoon [2576]: no message must be encrypted, 0x14a1, side 0 status
26/03/16 10:19:56, 352 raccoon [2576]: no message must be encrypted, 0x14a1, side 0 status
26/03/16 10:19:56, nesessionmanager 352 [2112]: Controller IPSec: IKE FAILED. phase 2, assert 0
26/03/16 10:19:56, nesessionmanager 353 [2112]: Controller IPSec: retry the aggressive mode IPSec with DH group 2
26/03/16 10:19:56, nesessionmanager 373 [2112]: phase 1 of the IPSec from.
26/03/16 10:19:56, 374 raccoon [2576]: IPSec to connect to the server $VPN_SERVER_IP
26/03/16 10:19:56, 374 raccoon [2576]: IPSec to connect to the server $VPN_SERVER_IP
26/03/16 10:19:56, 374 raccoon [2576]: connection.
26/03/16 10:19:56, 374 raccoon [2576]: IPSec Phase 1 started (initiated by me).
26/03/16 10:19:56, 374 raccoon [2576]: IPSec Phase 1 started (initiated by me).
26/03/16 10:19:56, racoon 376 [2576]: IKE Packet: forward the success. (Initiator, Aggressive Mode 1 message).
26/03/16 10:19:56, racoon 376 [2576]: > > > > > status of phase change = Phase 1 began by us
26/03/16 10:19:56, racoon 376 [2576]: > > > > > status of phase change = Phase 1 began by us
26/03/16 10:19:56, racoon 404 [2576]: port 62465 anticipated, but 0
26/03/16 10:19:56, racoon 404 [2576]: port 62465 anticipated, but 0
26/03/16 10:19:56, racoon 432 [2576]: IKEv1 Phase 1 AUTH: success. (Initiator, aggressive-Mode Message 2).
26/03/16 10:19:56, racoon 432 [2576]: > > > > > status of phase change = Phase 1 began with a peer
26/03/16 10:19:56, racoon 432 [2576]: > > > > > status of phase change = Phase 1 began with a peer
26/03/16 10:19:56, racoon 432 [2576]: IKE Packet: receive a success. (Initiator, Aggressive Mode 2 message).
26/03/16 10:19:56, racoon 432 [2576]: initiating IKEv1 Phase 1: success. (Initiator, aggressive Mode).
26/03/16 10:19:56, racoon 432 [2576]: IKE Packet: forward the success. (Initiator, Aggressive Mode 3 message).
26/03/16 10:19:56, 433 raccoon [2576]: IPSec Phase 1 established (initiated by me).
26/03/16 10:19:56, 433 raccoon [2576]: IPSec Phase 1 established (initiated by me).
26/03/16 10:19:56, racoon 453 [2576]: IPSec Extended requested authentication.
26/03/16 10:19:56, racoon 453 [2576]: IPSec Extended requested authentication.
26/03/16 10:19:56, 454 nesessionmanager [2112]: IPSec asking extended authentication.
[26/03/16 10:19:56, nesessionmanager 464 [2112]: NESMLegacySession[$VPN-CONN-NAME:72874CC0-2A89-4B61-80F1-9BB4F3EA953B]: status changed by disconnecting
26/03/16 10:19:56, nesessionmanager 464 [2112]: IPSec disconnection from the server $VPN_SERVER_IP
26/03/16 10:19:56, racoon 465 [2576]: IPSec disconnection from the server $VPN_SERVER_IP
26/03/16 10:19:56, racoon 465 [2576]: IPSec disconnection from the server $VPN_SERVER_IP
26/03/16 10:19:56, racoon 465 [2576]: IKE Packet: forward the success. (Information message).
26/03/16 10:19:56, racoon 465 [2576]: IKEv1-Information Notice: pass success. (Delete the ISAKMP Security Association).
26/03/16 10:19:56, racoon 465 [2576]: could not send message vpn_control: Broken pipe
26/03/16 10:19:56, racoon 465 [2576]: could not send message vpn_control: Broken pipe
[26/03/16 10:19:56, nesessionmanager 465 [2112]: NESMLegacySession[$VPN-CONN-NAME:72874CC0-2A89-4B61-80F1-9BB4F3EA953B]: status changed to offline, last stop reason no
26/03/16 10:19:56, 466 raccoon [2576]: glob found no match for the path "/ var/run/racoon/*.conf".
26/03/16 10:19:56, 466 raccoon [2576]: glob found no match for the path "/ var/run/racoon/*.conf".
26/03/16 10:19:56, 466 raccoon [2576]: IPSec disconnection from the server $VPN_SERVER_IP
26/03/16 10:19:56, 466 raccoon [2576]: IPSec disconnection from the server $VPN_SERVER_IP
It seems that I solved the problem, but I'm not sure it helped.
After restart of the operating system, the two connections: old and new Cisco via IPSec connection, began to work.
-
Using Cisco VPN Client in Windows 7 Professional 64 bit
Hi all!
I need to use Cisco VPN Client to connect to my server in the company, because my company uses lotus notes Server, I have to connect Cisco VPN to access e-mail. But now my windows version is Windows 7 Pro 64 bits that cannot directly install this application, I already installed XP Mode and creatde shortcut to Windows 7, I plugged the Cisco VPN to my Cisco VPN server, but I can not access the server, Pls help me and show me how to solve this problemOpen the XP VM itself, do not use the shortcut that was published in
the W7 boot menu. You need to install Outlook / your email client
Inside the virtual machine, as well as on the side of W7. You can point to the same
PST files if you have local PST files, but you just can't open them in
at the same time of W7 and XP VM.There is no way to bridge using the shortcut of publishing app
Some people have reported success with the third party IPSec
replacements as customer universal shrew or the NCP. Your IT Department.
would like to know if these are supported:
> Hello all! I need to use Cisco VPN Client to connect to my server in the company, because my company uses lotus notes Server, I have to connect Cisco VPN to access e-mail. But now my windows version is Windows 7 Pro 64 bits that cannot directly install this application, I already installed XP Mode and creatde shortcut to Windows 7, I plugged the Cisco VPN to my Cisco VPN server, but I can not access the server, Pls help me and show me how to solve this problem
Barb Bowman www.digitalmediaphile.com -
Different classes using Cisco VPN Client VPN
Hello
on a cisco ASA 5510, I defined a vpn group used for remote teleworkers who have access to the entire LAN using Cisco VPN Client 4.8.
I would give to others of this client, but I need to limit their access to LAN resources, which means that I have to have two types of users:
Remote LAN access
access to only certain IP addresses
Both must use the Cisco VPN client.
How can I do?
Thank you
This link should help.
-
Slow initial connection using Cisco VPN Client
I am currently using Cisco VPN Client v5.0.07.0290. Whenever I start my connection, it takes me about 90 seconds for the prompt to display authentication and another ~ 90 seconds to finish the auth. and connect successfully. I have another computer laptop w / the same WIN7 OS and version of Cisco VPN Client and he ends the connection to<30 sec. ="" why="" is="" this? ="" any="" suggestions="">
Hi Sergio,
You import the .pcf for the VPN Client file? If so, please try to recreate a new file .pcf locally on the machine itself and try to connect. Let me know how it goes.
Thank you
Delvallée
-
Client VPN router IOS, and site to site vpn
Hello
Im trying to configure a vpn client access to an ios router that already has a vpn site-to site running. I don't see how the two can run on the same router.
So I guess my question is is it possible? and if anyone has therefore had a config that they can share or a useful link.
IM using a router 800 series with 12.4 ios
Thank you very much
Colin
ReadersUK wrote:
Hi
Im trying to configure access for a vpn client to a ios router that already has a site to site vpn running. I cant see how both can be running on the same router.
So i guess my question is can this be done? and if so has anyone got a config they can share or a useful link.
im using a 800 series router with 12.4 ios
Many thanks
Colin
Colin
It can be done. Look at this config example that shows a router configured with a site to site VPN and client vpn - connection
Jon
-
Use the client VPN tunnel to cross the LAN-to-LAN tunnel
I have been troubleshooting an issue and cannot cross an obstacle. The ASA is running ASA running 1,0000 code 24. I am using a client VPN tunnel to connect to the ASA. The ASA has already a LAN-to-LAN tunnel, set up and operating and I need the VPN client to access the remote site over the LAN-to-LAN tunnel.
The internal IP address of the local part is 192.168.0.0/24 and the IP address of the Remote LAN-to-LAN tunnel is 172.20.1.0/24. The clients are distributed 192.168.200.0/24 IPs. I have attached the relevant configuration for the SAA.
When the VPN client on the network, I can access resources on the ASA network internal. On the internal network of the SAA, users can access resources through the LAN-to-LAN tunnel. Client VPN cannot access resources on the LAN-to-LAN tunnel. For the latter, there are no hits on the C-TEST access list.
Thank you for your help.
try adding...
permit same-security-traffic intra-interface
Maybe you are looking for
-
Cannot update or Uninstall Macromedia Flash player!
Hi people! I have a problem with the automatically installed Flash Player. I use a Qosmio G20. During the installation of a new program (financial Office Lexware) this program has tried to update Macromedia Flash player to the latest version. But the
-
Satellite L300D-242 - cannot install Vista after replacing HARD drive
Hi wonder if anyone can help mei have a L300D_242 toshiba satellite that broke down and I bought a new hard drive for it because the original was not good. I tried to install a Vista premium 32 bit on the new hard drive, but it does not install until
-
T430 W7Pro: Solution Centre message said: Miss me the driver "qknfd".
I am an exclamation point in the taskbar that brings me to the center of Lenovo's Solution, where I receive the message shown in the subject line. The buttons take me for Device Manager. I went through Device Manager and looked at all of the devices
-
Software account down from the system tray?
Hello I am looking for software of countdown running next to my clock in the system tray? I try Timeleft (with top functionality), but I'm looking more for those who are running in the system tray, so if I ever see my time I can see my account down?
-
Hi all. In our company we have recently upgraded our PIX 515 firewall to ASA 5520, and we started to live a thing strange event. On one of the sites we host, I saw a lot of outdated SSM messages popping up and I think that they are the source of the