International usability

Similar Questions

• Satego X 200 21U: drive HARD internal not external usable after upgrade

  First, I changed the system to a 500 GB HARD drive, and everything was good. The old drive was not usable extern, so I left it as an emergency backup device.
  After a few weeks, I did the upgrade even to the second HARD drive, and again the old drive is not usable in my extern Dockingstation.
  Does anyone have a good idea what causes this problem? The HARD drives are locking the entire system, if I try to access and some formatting.

  Hello

  What do you mean by is not usable in my external docking station?

  I assume that you have placed the 2.5 HARD disk in a USB enclosure that allows to connect the HARD drive to the computer USB port.
  Is this good? So what harm s? Is not recognized USB HARD drive or what?
  Have you tried to connect different computers HARD drive?
  Otherwise, to do this

  But if the HARD drive is not accessible, using the case of USB, or use inside the laptop, then I would say it is a HARD drive malfunction

  Why this is happening?
  The writing and the reading drive HARD is a physical process which underline the material parts such parts can still die

• HP probook 450 GB usable RAM

  Hello

  I have a HP probook 450 GO with Windows 7 pro 64-bit installed.

  The laptop has 4 GB of RAM installed, however, when I check this, right-click on 'Computer' then go to 'Properties', it shows 4 GB installed, but only 3.85 GB usable.

  Someone has any ideas why this is not displayed as 4 GB usable?

  Thank you

  If the system has integrated chipset graphics, part of memory is allocated to the integrated graphics chip and the rest is usable RAM.

  Hardware components often use some of the memory (RAM) of your internal system for themselves. For example, while a graphics (GPU) card comes with its own RAM, integrated graphics (also called integrated graphics card) uses part of your RAM as video memory.

  Your computer may also be allocating part of your RAM to other materials, such as your network hardware.

  To determine how much of your RAM is reserved for material and how much is usable by Windows, you can use the window system mentioned above. The total amount of RAM can be used is displayed next to the total amount of memory that Windows can see. In the screenshot below, 0,1 GB of RAM is reserved for materials.

  

• internal hard drives within the switching apparatus

  Switching of the internal hard drives in the machine. I have two internal hard drives, C and E of clarification and I replaced my C Seagate 360 with a TB Western Digital because of this hard disk failure false I bought, which I'm sure were a corporate scam to buy more stuff that is really unnecessary. My question is "how to pass these. My HP Pavilion Elite m9150f going in stupid mode on 3 to 5 times a year and I have to do a recovery and I found that doing the hard, it is happening in stupid mode in a very short time. I found is from the CD that it takes a little more, but the best way is to erase completely and reformat the hard drive and then do a clean install, so he prevents her from stupid mode for awhile, this one lasted 4 months but like you have probably understood it's time to do it again. However, as you know it takes 3 times as long to reformat TB as it does a 360 GB drive, so it's the root of my question. I have all my stuff on the E-Drive SG360 for backup, note here backup on this PC has never worked so I don't bother with the so-called machines back to top I just copy stuff I want to record on the E drive and make the ol' copy ' and paste to restore everything. Now because of the time it takes to reformat drive C TB I want to make the switch. Is it as simple as just their switching and pulling the PC with the recovery discs factory to perform RECOVERY and do my usual copy and paste of the Western Digital to now, E-Drive?

  Please someone with the know let me know

  Thank you very much, RickS

  Aparently, you can not RESPOND to your own message.

  No one answered so I went ahead and did it. Lost all learned but a lot on the partitioning of hard disks and all together, in addition to becoming the hard drive back to R & R until less than 6 minutes time to unplug the PC at the rear, turn 05:53, my best so far. but she is back to being usable was a day and a half.

  The answer to the question is when you put that there is nothing usable at all because the PC looking for the OS and boot any disk has. I had to start player, I chose so that I could erase and reformat the C drive and run the installation of the OS. Once he was done with that I had to choose again which drive start so I could erase and reformat the drive E then he would leave goes to the starting window when I turned it on.

  Simple answer is not a. Read above.

  RickS

  PS: I hope this helps someone.

  Hello

  Check with HP to factory reset of related problems.

  All the best Ricks!

• Server error internal 500 WRT54G2

  Hello everyone, I have a problem with my router WRT54G2. I was upgrading my firmware when my computer froze, so I had to leave. Afterwards, I couldn't connect to the configuration based on the web page more. I did a factory reset and installed again with Network Magic and configure my wireless key. It works now, however, I can't in the web-based configuration page. Whenever I go to 192.168.1.1 and enter my info, it says only: 500 Internal Server Error. I've always been able to access this page, now I can't, then I guess it doesn't work because of the firmware upgrade interruption. I do a lot of mac filtering and I limit the amount of IP addresses my router gives so if someone hacks my security key, they still won't be able to connect, so to access my router configuration page is important to me. I have reset (press and hold the reset button for 30 seconds - 1 minute) the router several times and still nothing. I mean, the router still works. My brother and I can always connect with our mobile phones, I can't get to the web-based configuration page.

  -What can I do to solve this problem or did I mess up irretrievably? Thank you.

  A few suggestions...

  Is first of all try to find the IP address of your router and see if she is still set to 192.168.1.1 through the command prompt. Then try to ping for the address.

  If you are able to ping, another 30 seconds and then reset flash the firmware on the router using TFTP. Download it here. Instructions here.

  If you are unable to ping it or the TFTP does not work, do a 30-30-30 reset. Instructions here.

  If these don't work, I'm ideas. Finally, you really don't need to put in place the MAC filtering because it's somehow more usable with spoof of MAC address. You would probably find that suggested on forums countless times, but just put a good passphrase WPA2 and're you good to go. If someone is good, enough to hack your WPA2 key (which is currently almost impossible), while he would have no problem getting your MAC filter.

• How to get an external drive officially used with a Mac to be recognized and usable with a PC running Windows 7

  I have an Iomega 500 GB external hard drive that I bought about 2 years ago I used exclusively with an iMac, until this computer crashed irreparably affordable last month.  My new computer is a HP Pavilion PC running Windows 7 and when I connect the drive I see in devices and printers that he acknowledged that an Iomega hard drive is connected to a USB port, but in the computer, it shows internal hard drive of the computer and the DVD player with their respective letter designations.  However, the external hard drive is not displayed.

  Fast disk information: I buy the player on the Apple store online in early ' 08, and when I unpacked it initially, I saw no written information not specifying that it was somehow a Mac version of this Iomega drive, there was anything about it either by declaring that use it with a Mac it format to use Mac only.   When I first plugged into the Mac, I was never invited on implementation shape or anything else specific to the Mac, actually, I was never even asked about the pilots.   To plug into it, he behaved as the USB flash drive and external 40 GB drive I have - a small orange icon appears on the desktop, with the name of the drive and the USB symbol.   So for two years, I moved the files between the player and the Mac with no problems, until now, when I try to use the drive with my current PC.

  So far it was suggested to me that makes the Mac * fact * format the drive in a way that makes Mac only, and I can't reformat because I have given, I must first of all get moved to the new computer.  Another theory is that since entering at Apple, even though it is an Iomega product, it might have been shipped with a tweak specific to Mac-maybe it was already formatted for Mac use.  A third theory advanced for me, is that it could be that the cable company somehow makes the PC is not quite completely recognize it.

  Any info would be greatly apprecitated.   Worse, I can find someone with a Mac and we can move files from the Iomega to the Mac hard drive, then the 40 GB drive which * fact * work with both types of BONE, and that several times until everything is moved safely to the new computer, then can do what I do with the Iomega is usable with the PC.

  What I find a bit confusing, it's the 40 GB has never had problems of compatibility with any computer with which I have connected.  In the course of graphic design, I've been in we have Mac and PC in the same building and that player never cared that it was connected to.

  There is a format uses Apple (don't remember what it's called...? Trip...? Journal... something like that) that Windows cannot yet see.  So once you have the files and folders saved on something like the DVD, do not format NTFS for Windows can see it.  The good thing is that Apple may also see NTFS, once it is formatted and files/folders copied on it, you will be able to use all the PC under Windows or OS.

• internal hosts cannot access the internet w / L2L configured tunnel

  The internal hosts behind the ASA cannot access the internet with a configured tunnel to L2L. The L2L tunnel is mounted and passing traffic correctly. However, the internal host cannot access the internet through the ASA. I think I have my NAT watered somewhere. I can't even a host statically mapped to the internet. It might be because I'm used to having a WAN IP to the external interface which differs by the CIDR block assigned by the ISP. In this case, it's all together, with the ASA outside interface occupying the first available address.

  We have been assigned a CIDR range x.x.x.64/28. x.x.x.65 is my front door and my first usable est.68, by the PSI (I guess what they utilisent.66 et.67 for internal use). External interface of the ASA est.68 and I'm trying to get NAT others. I'm Polo all DHCP clients internal and have some static entries as well. Below is the relevant NAT config. Yet once, all traffic passes above the tunnel properly, but not from inside to outside. If more information is needed, please advise.

  interface outside

  IP address x.x.x.68 255.255.255.240

  NAT-control

  Global x.x.x.69 - x.x.x.77 2 (outdoor)

  Global 1 x.x.x.78 (outside)

  NAT (inside) 0 access-list sheep

  NAT (inside) 1 10.10.10.0 255.255.255.0

  public static x.x.x.69 (inside, outside) STATIC_NAT_EXAMPLE netmask 255.255.255.255

  internal access-group interface inside

  Route outside 0.0.0.0 0.0.0.0 x.x.x.65 1

  internal to the 10.10.10.0 ip access list allow 255.255.255.0 any

  ! Remote LAN is 192.168.10.0/24

  access-list sheep extended ip 10.10.10.0 allow 255.255.255.0 192.168.10.0 255.255.255.0

  Can you post a "show sysopt run?

  Try this command to enable proxy arp.

  No outside sysopt noproxyarp

• internal drive shows in computer science, but "is not accessible.

  After that chkdsk on a usable internal drive, I used 'Start' - 'computer' the drive icon. I get "F:\ is not accessible - access denied. When to use disk management; the disc comes with.

  3 basic GB 1397.26 drive healthy (primary, active Partition' in the block on the left and the right block is completely empty.) I want to get it even if I have to reformat.

  Fixed - had to remove thedisk drives and reinstall all the cables - they reappear and were usable at the next startup.

• How to use a partition on a hard disk internal to the file history

  I try to use a partition on my hard drive for the file history. When I open the history file it says "no usable disk found. I allocated about 50 GB of the partition. The size of partition of the problem or do not like the internal disks for the windows backup? If the disk is too small if you please could you recommend a minimum size and if windows does not like the internal drives for backup could you please tell me how to solve this problem.

  Note:    I know it's a bad habit to save on the hard drive, the same that your files are on, but the point of this backup is not file security, more so I can go back to older versions of files such as windows 7 versions. I have an external hard drive dedicated with full backups, but it does not gives me the opportunity to return to an older version of a file at any time as the historical file is that I'm not wearing my backup drive wherever I go.

  Thanks in advance

  Try to make a file on your partition named FileHistory.  .   Right-click and select Properties.   Share it.

• Memory 4 GB (2.75 GB usable)

  Computer laptop (Win 7 Pro 32 bit) has 2 GB internal memory and a slot for adding more. According to the card, it will take up to 8 GB. I added a stick more than 2 GB and in the configuration/system Panel, it tells me that there is 4 GB (2.75 GB usable). I know video and other stuff using a part of the memory (May. 25) but miss me more than 1 GB. 'Memory Max' is not checked, not sure what else to do. Help, please.

  HP Compaq 6735 b (included with Vista, put XP Pro and now is a clean load of Win 7 Pro)

  Thank you.

  Hey pavlichok,

  A 32-bit (like Win 7 Pro 32-bit) operating system supports a maximum of 4 GB of memory (including video, RAM memory and others...). See this article: http://support.microsoft.com/kb/978610

  Thus, there is absolutely nothing wrong with your laptop, your RAM or your hardware. All you need to do is to install a 64 bit version of Windows 7, and you can then use all of your memory!

• Using the links internal pdf when you view the document online

  Hello

  I created a pdf document with internal links to different parts of the document. However, when I published in Acrobat.com to share, links are more operational. Is there a way to keep the operational links being seen online? (Once download you them they are usable again)

  Thank you, Daniel

  Hi dalvo2002,

  I'm sorry, but the links are not rendered in the preview of the files that you see on Acrobat.com. The links are not removed from the file (as you have discovered), they just are not included in the preview.

  Best,

  Sara

• I moved the LR5 files by dragging them to a new location. Why the LR5 keep folders and files on the source drive internal Mac?

  my 1 TB drive iMac is full.  I bought a LaCie 3 TB external and moved from 2012 to 2014 to the new drive records.  I did carefully by renaming in year-mo-date__topic in the records of LR.   Then, I used LR5 to drag files in front of the Mac the LaCie external HD.   Successfully, everything installs and turns and usable LR5 since the 3 TB LaCie drive.  The Mac HD is no longer displayed in LR.  In Solution Explorer, I still have folders 2012, 2013 and 2014, but it is still consuming most of my internal drive.

  Why LR5 did move all files instead of what seems to be the copy?

  LR5 instant:

  

  Snapshot of the Explorer:

  

  Hello, on a Mac, it's Finder rather than explore...

  On a Mac, there is no movement when the transfer between discs only copies. It is a large safety factor so that accidents can be overcome for example a power failure during the transfer.

  All you need to do (after saving two disks) is to move files on your internal drive to the trash and empty it then. That will free up the space.

• Internal link problems

  Hi, hope someone can help because I'm a bit stuck.

  I designed a form in Adobe Designer 7 which has internal links that jumps the user to a section of the form to another according to their answer to a question.

  These links work fine in Adobe Acrobat 7 Professional, but I can't seem to work in reader regardless of the version. No error message... all in all, nothing happens when they are clicked.

  The code behind the radio button is xfa.host.setFocus("form1.page6.textlink1") where form1 = the name of the form, the links and the textlink1 landing page = page = the specific destination.

  Any help at all would be greatly appreciated.

  Kind regards

  Stephen.

  For the benefit of third parties as a result of this post. The issue was that the location of the target where the link was intended has been set as invisible. This means that the field is not part of the layout but is a valid field. The expression was beautiful (the field is a valid field), but because the cursor could not be placed in a field displayed, it wouldn't move. Make the visible field, make sure that there is no legend, and no appearance, then check the field 1 point per 1 point. This will make the field virtually invisible to the user and still usable by the command.

  Paul

• IMSG hacked account, sending a lot of international text in current bill

  So yesterday my pirate apple account (connected from a unknown macbook) and I noticed someone was frantically sends many messages from my phone, images which got also sent as normal text to an international number. After noticing, I quickly changed password. Checked my mobile BT phone bill, and he had already executed a bill for all these messages sent to international numbers. The appeal of BT until you see what they can do and they just said, you will have to pay for the Bill and that was that.

  What to do about this? my password was normally good security level and don't even know how he hacked. How would stop it doesn't happen because it looks just like any time I could just be landed with a massive Bill. Fortunately, I noticed pretty quickly this time, so the Bill does not accumulate to something that would be unfeasible. But with the telephone companies want to help at all, it seems extremely unfair!

  Try to use the two-step verification!

  Details here for Apple ID - Apple Support two-step verification

• Is it possible to reinstall or reset the internal microphone of an iMac?

  Some background information:

  27 "iMac 5K (end of 2015) running OS X El Capitan (when the problem started), to give birth to Sierra of MacOS. Also have a Bootcamp with Windows installed 10 partition.

  A month ago, when under OS X, I noticed the internal mic produced some static when you try to use it. Audio messages in voicemails would be static instead of my voice. The weird part? If I switched to Windows 10, the internal microphone works without any problem. I can ask questions of Cortana, I can record voice messages and they read without static electricity. In fact, no matter what I use the microphone internal to in Windows, it works perfectly.

  Sierra of MacOS is out, so I hope that this update may be a BONE would settle the matter. Nope. Internal microphone still does not work on MacOS, but still works perfectly in Windows 10. It is because of this that I am positive the internal MIC is not broken or have a loose wire.

  I went through a few steps to try and fix the internal microphone, such as resetting the SMC... but nothing has worked. Any help or ideas on how to solve this problem would be greatly greeted.

  Hello dear user

  Thank you to use Apple support communities

  My recommendation would be to take it to an official Apple store, workers are espceialists, they might be able to fix, make sure also that you have never removed the water on top of the mic. In my iPad, a drop of water directed the music video of speaker if she never exceeds 30% volume of the music.

  But if you don't have a store nearby, uninstall malware and unnecessary software, make sure that you don't have a program that allows you to change your sound (like Skype) systems, if you don't do that this program has no impact on your microphone. (I used to have Skype but it also makes audio cut so terrible, piano music sounded like heavy metal music, so heavy metal music was like to...) I don't know what to say.)