IO Error Establishing connection network card couldn't

Similar Questions

• Not connected network card

  My laptop says he not a network card, I can't connect to internet via wifi or with a cable, he said also that I don't have the ehernet controller network controller PCI Device and SM Bus controller drivers

  If you can borrow an internet friends, you can download the drivers, to transfer them to a Flash DRIVE or a CD.  Without network drivers, you cannot connect to the internet.

• vmotion - box connected network card question is uncheck after vmotion

  Hi all

  I have a strange problem in Cluster DRS / rules of VM, we do vmotion

  After doing vmotion, VM addresses don't not ping, in the first time I think it's trunk network was not good.

  Do vmotion on the source host and not work.

  After checking configuration of the virtual machine, I see that "Connects" network adapter box is not checked.

  The box was check before, because the ping response machine before the vmotion.

  My question is very simple you already have this behavior?

  I use the following script to facilitate the operation.

  Thanks for your help

  Ludovic112

  $pViServer = '< servername > '.

  
  If ($viCon.IsConnected - eq $false - or $viCon.IsConnected - eq $null)
  {
  $ViCred = get-credential
  $viCon = Connect-viServer-Server $pViServer - Credential $viCred

  }
  
  $vmName = "< vmname >.

  
  $maVm = get - vm $vmName

  
  $cluster = get-cluster "< NOMCLUSTER >".
  $Listvmhosts = $cluster | Get-VMHost

  foreach ($vmHost to $Listvmhosts)
  {
  If ($maVm.host.name - eq $$host.name)
  {
  Write-Host "nothing to do" $maVm.host "-" $vmHost.Name
  }
  on the other
  {
  Write-Host 'migrate' $maVm.name 'to' $vmHost.Name
  Move-VM - VM $maVm - Destination $vmHost
  sleep - 60 seconds
  }

  }

  If the connected box gets uncheked after vMotion, looks like the maximum number of ports configured for your vSwitch on your target hosts is exceeded...

  / Rubeck

• Dial-up error 720 and network card issues

  When I try to connect to my dial-up connection, right after that it says "Register your computer on the network" I get

  Error 720: a connection to the remote computer could not be established.

  I contacted my ISP and the issue appears to be on my end, not their

  Moreover, in my network adapters: you can see the maps marked in yellow in this screenshot

  http://i1178.Photobucket.com/albums/x374/K29000/network_adapters.jpg

  errors:

  Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (Code 39)

  I don't know if that is related to my problem of remote access. They all seem to be duplicates of NICs are working properly. (Except that they say 'miniport eacfilt' at the end)

  I tried to uninstall these duplicates which I think are the leftovers of other software that I have installed at one time (he said that the seller is Nortel, but I have more no Nortel software on this machine), but they won't disappear.

  I can still connect to the internet fine through a usb 3G modem that I borrowed. Although, when I do gives me a message that "another computer on the network has the same IP as this one" but after the closure of the message, the internet still works fine.

  I could not check if ethernet and wifi services works properly. The last time I used them was a year ago.

  I'm on Vista Business 32-bit SP3. Laptop: Acer Travelmate 5320

  Any help would be greatly appreciated.

  Hello

  I suggest you to follow the link and run Microsoft Fix - it and check if that helps.

  Hardware devices do not work or are not detected in Windows

  I hope this helps.

• Error establishing connection to OBIEE for Essbase administration tool

  Hello

  I want the tool OBIEE Admin (on PC) to connect to the Essbase server.

  But I can't get it to work.

  ***

  BIEE 11.1.1.9.0

  EPM (Essbase Client) 11.1.2.3.0

  ***

  The error is: "Essbase error 0.

  In the local log file:

  [2015-06 - 04T 15: 27:46.566 + 02:00] [OracleBIServerComponent] [NOTIFICATION: 1] [] [] [ecid:] [tid: 1 b 64] [46158] Administration verwendet language DEU.

  [2015-06 - 04T 15: 27:46.573 + 02:00] [OracleBIServerComponent] [TRACK: 1] [] [] [ecid:] [tid: 1 b 64] loading metadata javads

  [2015-06 - 04T 15: 28:48.251 + 02:00] [OracleBIServerComponent] [ERROR: 1] [] [] [ecid:] [tid: 1 b 64] error Essbase 0

  [[file: server\Query\Execution\DbGateway\DbGatewayEssbaseCAPI\PrivateInclude\SQXDGEssbaseCAPIImport.h, line: 67]]

  ]]

  Be kind enough also to take a look here, since there are already some extra info:

  Business Intelligence > Business Intelligence Foundation > Business Intelligence Suite Enterprise Edition > Diskussionen

  https://community.Oracle.com/thread/3730336

  I'm not sure if this is a problem of setting (path) at all. I've seen a lot of different "correctness" and recommendation in this regard - taste too for my personal use... and non of them changed the game well.

  I'm a bit desperate.

  Thank you very much in advance and greetings.

  André

  I had really any problems.

  The client computer, installed 11.1.1.9 OBIEE administration tool.

  An Essbase installed 11.1.2.4 customer, I installed this version as it corresponds to OBIEE 11.1.1.9 as who uses 11.1.2.4 drivers.

  Update bi_init.bat to include the ESSBASEPATH variable and adds the path to the variable ESSBASEPATH\bin

  

  Open the online administration tool, import

  

  Tested the connection to two 11.1.2.3.506 and 11.1.2.4 Essbase

  

  Imported fine.

  See you soon

  John

• Satellite L300D - establish wireless network card

  I need help determining what wireless card for this laptop to 11V L300D PSLC0E-00900DEN.

  I have reflected on this web site for laptop, but there isn't. The model name is different from the one on this site. I guess this laptop came with wireless built in, because he had the sticker on it. Purchased just before Christmas for my little brother for pc world.

  I can t get out that that his card bus or the express card slot or the pc card slot.

  Any help would be grateful

  This laptop Satellite L300D has a card Realtek RTL8187B WLAN.
  The laptop is listed on the download page of the Toshiba driver and the driver Realtek too. I found exactly your model.
  http://EU.computers.Toshiba-Europe.com

  The slot on the side is an express card slot.

• SCO UNIXWARE 7.1.1 install vSphere 4 (ESX 4) ERROR problem with network card

  Hello

  I try to install SCO unixware 7.1.1 on vSphere 4.

  Install and configure sco OK after installation OK, but after you configure NIC SCO is dead

  PANIC: Integer zero-divide trap in kernel mode

  When I disconnect the NIC so unixware run OK

  Thank you

  This looks like a known bug of UnixWare.  You must install SCO UnixWare Maintenance Pack 5 before setting up networking.

  Please see the section of the Guest operating system Setup Guide for SCO UnixWare 7.  In particular:

  Note To avoid a kernel panic, install MP5 before performing any configuration network on UnixWare 7.1.1.

• Compaq Presario V6000: exclamation point next to the network card in the BIOS Setup

  Hello

  Recently, I find the wifi on my laptop does not work with projected light orange. I tried hard to stop my laptop, remove the battery and then restart the same thing with resetting the wifi button but of no use. Also with F10 if I enter the configuration for starting it I find exclamation close the my network card with the message that the ability to start will be disabled if the device with the exclamation mark.

  Please let know us, as I did also update my network drivers.

  Concerning

  Arvind

  Hi @Arvind_1990 ,

  Welcome to the HP Forums!

  It's a great place to find answers and suggestions!

  You have the best experience in the HP forum, I would like to draw your attention to the Guide of the HP Forums Learn how Post and more

  Compaq Pressario V6000 series laptop, what your exact model?

  How can I find my model number or product number?

  I understand - you have a problem with your wireless network. You tried to update the drivers, but there was no change.

  Did you of recent changes made to your Internet provider or router?

  If you go into Device Manager there is an error on the network card?  If yes what is it?

  Here is a link to HP - troubleshooting your wireless network computers and Internet (Windows 7)

  Have your tried running MS Fix It for help with this difficulty?

  Good luck!

• When I try to establish a wifi connection, it shows that the problem with the network card is not fixed. How can I solve this problem?

  When I try to establish a wifi connection, it shows that the problem with the network card is not fixed. How can I solve this problem?

  Hello

  Thank you for writing to Microsoft Communities.

  Until we start troubleshooting on this issue please provides us additional information by answering a few questions, this will help us better solutions to the problems.

  1. What is the full error message do you get?

  2. are - that you be able to access or connect to the Internet via wired?

  3 have there been recent changes to the computer before the show?

  Please go ahead and follow the steps mentioned and later a update on the State of the question.

  Method 1:
  Try to run the network troubleshooters. Check if it enumerates and helps resolve the errors.
  http://Windows.Microsoft.com/en-us/Windows7/open-networking-troubleshooters

  Method 2: If the problem persists, try to follow the steps from the link.

  In the Windows wireless network connection problems:
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Check this link for more information:

  How can I troubleshoot network card? http://Windows.Microsoft.com/en-us/Windows7/fix-network-adapter-problems

  Why can't I connect to the Internet?
  http://Windows.Microsoft.com/en-us/Windows7/why-can-t-I-connect-to-the-Internet

  Please follow these recommended steps and post if you still experience the problem.

• Error code 797: connection is not available because there is a problem with your network card or modem

  I have a Windows 7 laptop. I use broadband (DSL) to connect to the internet. Lately, I have an error with the code 797. It says connection is not available because there is a problem with your modem or network card. I have a Sony Vaio e series laptop.

  Hi Muffakham,

  Thanks for posting your question in the Microsoft Community forums.

  I see from the description of the problem that you are unable to connect to the Internet and receive "Error Code 797 connection is not available because there is a problem with your network card or modem".

  I imagine the inconvenience that you are experiencing. We are here to help and guide you in the right direction.

  To provide the proper resolution, that I would need more information on your side.
  Did you the latest changes on the computer before this problem?

  This problem may occur because of damaged or incompatible, drivers connection settings incorrect network, hardware or software problems and missing updates.

  Method 1:
  I suggest you try the procedure described in the article and see if it helps.

  How can I troubleshoot network card?

  http://Windows.Microsoft.com/en-us/Windows7/fix-network-adapter-problems

  Method 2:
  If the problem is not resolved, I suggest you try the procedure described in the article and see if it helps.

  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Check out the link for more information.

  Why can't I connect to the Internet?
  http://Windows.Microsoft.com/en-us/Windows7/why-can-t-I-connect-to-the-Internet

  Let us know the status of the issue after you perform the troubleshooting steps. If you need information about the problem with the connection to the Internet or get help, I'll be happy to help you. We, at tender Microsoft to excellence.

• Unable to connect to the Internet error "Windows does not detect a network card installed properly"

  Internet does not connect and connection was well 5 hours ago. Message states: "Windows did not detect a network card installed properly" How should I proceed? Connection is on the laptop, but also other devices. Problem is only with the office.

  Any help is appreciated

  OT: Internet connection

  Hello

  You did changes to the computer before the show?

  I suggest you try the steps from the following link:

  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

• Questions of ESXi 5.1 ISCSI--&gt; cannot establish a network connection (continued)

  Hello world

  I had a problem there not too long ago (thread link below) where my ESXi hosts could not establish a connection with an IBM DS3500 on start up and "rescan", however their connectivity worked correctly without any problem after commissioning and when a "rescan" finished. We determined that the most likely cause was the unit IBM itself. However, I wasn't completely satisfied.

  In order to deepen the question and dismiss my guests being the problem, I created a unit ISCSI myself with two new hosts of ESXi 5.1 (version 1157734).

  ESXi signals that it cannot connect to the initiator ISCSI (network error) - but it can run virtual machines and browse data stores?

  The configuration is the following:

  Test environment:

  2 x ESXi 1157734 hosts

  1 x server Freenas ISCSI (ZFS R10)

  At the start of my ESXi hosts in the test environment, download the same error as our production environment. They also put on the same error message (in the event log) when I "rescan" map of the ISCSI software. However, once the scan is finished, I can't see any error message and everything continues as it should (Round robin, active active). I can get a brilliant flow also. It's as if the errors are almost... false positives?

  Example of the error message (test environment):

  Connection to the iSCSI target

  IQN.2011 - 03.org.example.istgt:iscsi on vmhba35

  @ vmk2 has failed. The iSCSI initiator couldn't

  establish a network connection to the target.

  error

  17/10/2013-08:33:35

  ESXi hosts are configured as follows:

  Test environment:

  • (ESXi hosts) Two network cards for ISCSI, one for VM traffic
    • NIC1: 10.20.20.2/24, NIC2: 10.30.30.2/24
  • (Freenas) Two network cards installed on the ISCSI device (dedicated to ISCSI traffic)
    • NIC1: 10.20.20.1/24, NIC2: 10.30.30.1/24
  • ESXi is set to round robin, which works properly (I can max on both ports at the same time)
  • Two VMKs are related to the ISCSI Software initiator and defined to dynamically discover the two ISCSI addresses
  • Unity of ISCSI and the hosts are not on the VLAN, the switch is dedicated to ISCSI traffic (However in the production, the two networks are separated by VLAN.) I removed the in the test environment to simplify everything)
  • The vSwitches (who hold a single VMK for ISCSI) are fixed:
    • "Promiscuous" mode: reject
    • Change of MAC address: accept
    • Forged passes: accept
    • The traffic shaping: disabled
    • No NIC teaming (obviously)
    • Each VMK inherits the settings of these

  Quick points:

  • My hosts use VMware approved NIC in my test environment. My production environment runs on full VMware hardware approved
  • Can I use ping of vmk join each each VMK ISCSI initiator
  • I can use the nc-z target_ip 3260 command to check connectivity to the port
  • The ISCSI test has two network adapters, each on 1 Gbps ports
    • I can get around 800mbps per port when copying lots of files (both ports are active)
    • I see no error in copying a large number of virtual machines around, or backup files
  • I only see errors on start up and "rescan".
  • I have two network adapters on each host ESXi dedicated for ISCSI. Each NETWORK card has a single VMK. A single mapped port on ISCSI, the other is mapped to port B (I used to have two VMKs by nic, but I removed that in order to simplify everything)
  • I have updated the firmware on our switch of production. No results
  • I've used 4 different switches in order to avoid a network problem. No results
  • I tested ESXi versions 5.0, 5.1 (799733 & 1157734), all have the same mistakes
  • The ISCSI ports are on different networks according to the VMware (I was told not to put on the same network VMKs)

  Any ideas? It's starting to drive me up the wall. Any help would be greatly appreciated

  I've seen several times in recent months and was beginning to think it is specific to the HP P2000 units because it's the only time wherever I saw him! I now believe that ESX/iSCSI rather than issues of driver or table.

  On my last install, I found that errors occur as soon as the table is connected, i.e. before any storage is displayed.

  Single host ESX, no guests. 2 Intel adapters to 2 HP past by dedicated HP P2000 1 GB table with all 8 wired ports.

  All roads are good, all lights are in the State expected.

  It did not affect the use of the storage in question to any site, so there has been no need / a momentum of any further investigation.

  B! 886y annoying however!

• PC problem error 4609, more Services Auto off, No system, no connection network restore

  Win XP SP3:

  I can't open an element of individual logs in the application log.

  It connects 4609 error repeatedly.

  System shows a network card, but it does not show under network in the control panel.

  Most of the Auto Services are OFF... and they will not start.

  I am running an analysis of McAfee Viruscan then Stinger and Malwarebytes.

  (EDIT... Malwarebytes does not... associated with stopped services?... error is Runtime Error 32... failed to load control 'lvbalGrid' vbalsgri6.ocs.)

  What can I do else?

  I use the system update WSUS... and updates if it is enough to run on this PC.  It had not updated in a few months.

  EDIT: Device Manager appears normal.

  I have an other PC SP3 of XP which has the same symptoms:

  No network connection

  does not have malwarebytes

  no system restore

  Cannot open elements individual event viewer

  many auto services are turned off

  both started around April 21, when I published updates to the WSUS Server Windows.

  I have 2 PC more than probably having the same problem.

  Edit3: Use memory and CPU in both computers is very low... nothing happens... no network activity at all.

  solved... I couldn't wait and had to call the excellent support... credit MS Bus support!

  McAfee Viruscan has caused the problem of corrupt the windows\system32\svchost.exe file.

  I fixed it by replacing the file svchost.exe with a good known of xp sp3... and McAfee update to the latest DAT files.

  Because him copy / paste was dead, I had to use DOS or cmd.exe to copy the file from a USB key.

  http://blogs.technet.com/configurationmgr/archive/2010/04/22/Configuration-Manager-2007-task-sequence-to-assist-in-resolving-McAfee-antivirus-deleting-Svchost-exe.aspx

• BIOS error 104: network card not supported after the update of the bios, HP G60

  Recently, my hard drive has begun to fail. I bought a new drive, installed a Windows 7 ISO on a flash drive, installed etc. I have a HP G60-237NR. I have reinstall everything, and then I went to the page of the drivers for my laptop. I started to install stuff, at that time there I was bored so I'd sort of from the bottom to the top if this order of the questions, I can give more details on that if I need to. I downloaded the BIOS update, because I thought that "good, he he listed for my computer, I have no doubt it needs to be updated since my laptop like 6 years. Flashed the BIOS, my computer shut down and restart didn't like I thought he was supposed to. I turned on and well 'device 104 - unsupported of detected wireless network. System stopped. Remove device and restart. "I tried to find out what to do, which told me to remove the network adapter, the bios downgrade, plug it back and you're good. Well, I unplugged my network card and the snap-snap-in two sons who attaches and restarted, he did all the stuff. I got the same error. EDIT: I meant I plugged my network back in, but still got the error. Where I had the clichés about evil, I passed the clichés and double checked the connections maps, but still nothing. Everything I found said that should have worked, I'm on the same version of the BIOS, I started with that, but it does not recognize my network card. What am I doing here? Please help, thanks.

  Hello
  
  When you have the outside wireless card, you have the error?
  
  If this isn't the case, then you can get necessary to replace the wireless adapter. I would not be able to explain how, but something may have cause to fail.
  
  You can find maps of replacement of support on page 16 Chapter 4 of the Guide Service and Maintenance for your laptop.
  
  I hope this helps.

• HELP Please: problems connecting to Google Chrome or Internet Explorer: think it has to do with my network cards

  My computer works perfectly except that I can't connect to the internet using Google Chrome or Internet Explorer. Internet works fine.  I have another computer that is connected to the same network, and it works fine.  Also my signal strength is optimal. When I try to go on Google Chrome, it says that the web page is unavailable & the reason why is error: 105 (net: ERR_NAME__NOT_RESOLVE) the server is not found.  When I try to use the Internet, I get this message:

  Device is not working properly because Windows cannot load the drivers required for this device (Code 31)
  I've tried everything and looked at other forums. I went into Device Manager and tried to update the driver, but whenever I do it just says that all updates are already made.
  I really feel that my problem has something to do with network cards. When I go to Device Manager and discovered the network adapters 13 different adapters appear. The 1st is Atheros AR5007 802. 11b / g Wireless Adapter and it looks like it works very well but there are 11 different (Microsoft 6to4 adapt #10) (all have different # s, 10,11,12,14,15,16,17,18,20,5,9) there is (NVIDIA nForce Networking Controller)
  I think the problem is with the Microsoft 6to4 adapters because win I right click & then click on PROPERTIES of each adapter says: State of the device, this device is not working properly because windows cannot load the drivers required for this device. (Code 31) So, is to "find solutions", says & when I do that nothing happens, a message flashes on the screen that says: "Could not load driver software" and that windows is looking for information, but nothing ever happens.
  Can some1 please help me! My computer worked fine and both Google Chrome and still worked and then out of the blue it just stoped working. Any information would be very useful

  wisports,
  Thank you for visiting the Microsoft Answers community forum.

  You have found the source of your problems.  You must remove or uninstall, all the cards of 6to4.  Also delete everything that said map Tunnel or card miniport WUN.  Also uninstall or disable, Internet Protocol version 6 (TCP/IPv6) Properties tab on existing network cards.

  Once you have done these things, restart the computer and make sure that the 6to4 adapters does not return.

  Let us know how it works for you.
  Thank you
  Gloria
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.