iPhone SE: "no service," cannot see network after 9.3.5 update

Similar Questions

• My iphone shows no service with all networks in Egypt also sometimes works and all this happened all of a sudden

  My iphone shows no service with all networks in Egypt also sometimes works and all this happened all of a sudden

  If your provider supports iPhone

  I'd look for an update to the carrier

  Settings - carrier - it will pop up if available

  And if there is none then speak to the carrier a replacement of the SIM card

• How is it, windows XP or Windows 7 cannot see network drive?

  first of all, I have 5 computers.  Installed with Windows 7 installed with Vista and 1 2 3 MacBook Pro.  I created 1 network drive to more easily move files named "ShareMe.  All the protable can use the shared folder since I gave permission to everyone.  All the computer can use the network printer.  I installed Windows 7 on a Mac using VMware 2.0.5 and able to print using printer network with no problems.  I installed another Windows 7 on VMware Workstatin on a PC, and it can use the network also printer without any problems.

  (Everything is legitimate and so far I just was not updated to 2.0.6 because I heard a lot of things to have a slow speed)

  That is the problem, not an operating system that runs on VMware can't see my shared folder in the network, it cannot see networked host computer.   I speak not shared folder between VMware and the computer host.  Between the host and VMware are very well; However, I'm talking about that all shared folder the computer can see (folder ShareMe).

  All in the same workgroup

  Using NAT to network adapter

  Tota1 wrote:

  Using NAT to network adapter

  This is the problem because it puts the virtual machine on a separate subnet, then the one on the host is.  Past to open and release/renew IP on each virtual Machine.

  Take a look at: Understanding Networking in VMware Fusion

  Tip: With a Machine virtual Windows switch between NAT and connected by a bridge or visa versa, can be made without restarting, or even by using ipconfig to release/renew the IP address.  Simply toggle the State connected/disconnected from the network of the <...>Network icon on the status bar from the type of network between the two. It takes but a few seconds and a few clicks and is faster and easier the alternative methods.

• vCenter Server service does not start after you run Windows updates

  On a regular basis, my vCenter Server service fails to start after the automatic updates of windows are applied.  The vCenter server is a datacenter 2008R2 VM.

  The only other running applications are PerfectDisk and agents of ESET NOD32 - vCenter is in 4.1.  I tried to adjust the vCenter Server and WedAdmin service of delayed start, but that doesn't seem to make a big difference. The following errors are displayed in the case of the newspaper which lead me to think the issue is related to SQL:

  SQL Server is not ready to accept new client connections. Wait a few minutes and try again. If you have access in the error log, look for the informational message that indicates that SQL Server is ready before trying to connect again.  CUSTOMER:: 1

  The description for event ID 1000 from source VMware VirtualCenter Server can not be found. Either the component that triggers this event is not installed on your local computer or the installation is corrupted. You can install or repair the component on the local computer.

  If the event is on another computer, the display information had to be saved with the event.

  The following information has been included in the event:

  Could not initialize the VMware VirtualCenter. Closing...

  the message resource is present, but the message is not in the string/message table

  Anyone encountered this before?

  Hello.

  I didn't know this, but the info in Ko 1007669 may be useful.

  Good luck!

• Cannot see network on XP Server after reinstalling the operating system

  After reinstalling the operating system on our server, I can't see our server on the network. In the Service list after going to TCP/IP--> INSTALL network, I do not see "Sharing files and printing for Microsoft networks" in the category of SERVICES.
  I see all the other nodes in the network (which consist of several Win7 and Win XP machines).

  Hi BigGtheDood,
  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the TechNet Forums.
  http://social.technet.Microsoft.com/forums/en-us/winservergen/threads
  I hope it helps. If you have problems in the future, please let us know. We will be happy to help you.

• Cannot see network devices again after starting

  After much research I finally got this win 7 to see everything on the network.

  Stop for the night, the next day it only sees nothing himself. Other computers can see and access in accordance with the policies and authorities.

  Win7 Ult 64 bit sp1

  wired network work with all devices in the same working group - no domain

  Discovery, f & p actions and sharing password protected are all on.

  Services DHCP Client, DNS Client, function Discovery Provider Host, network connections, Network Location Awareness, SSDP Discovery, computer browser and UPnP device host are all set to start automatically.

  In the editor group policy wait for network is enabled and homegroup is disabled.

  After a while, he sees the router in the network map.

  All Wi-wired and network cards have booked the D - Link DIR-655 Router ip addresses

  At this point, it must be something stupid - that's the rule!

  Hi Rafisher 1.

  Thanks for the reply.

  I suggest you to ask your question about Windows XP in this forum for XP Windows IT Pro: http://social.technet.microsoft.com/Forums/en-US/category/windowsxpitpro

  Thank you.

• My laptop cannot detect wireless networks after using the Windows Update service. Technical support, very desperate need.

  I tried the direct technical support, but it seemed to have cut. Given that I can no longer connect to the internet on my laptop, I'm with my playstation browser and painfully by typing with the controller.

  My probllem.
  I have an ASUS Intel Core i3 - 2350M CPU @ 2.30 GHZ running Windows 7 home premium. I've selected "Windows Update" in the start menu and proceeded to download and install all updates. Once the updates have been installed, my laptop couldn't detect wireless networks which means that I can't connect to my router and have lost the internet.
  Device Manager indicates 802.11n Wireless LAN Card is working properly.
  Windows did create a restore point before installing the updates, but everytime I try a restore I get the following message
  "System Restore has failed. Your computer's system files and settings were not changed
  Details
  System Restore could not access a file. This is probably because an antivirus program is running on the computer. Temporarily disable your antivirus program and restart System Restore.
  An unspecified error occurred during the restoration of the system (0x80070005)"
  "I disabled anti Virus AVG and COMODO firewall only to receive the same message, and it now appears that the restore point disappeared as if by magic, saying system restore ' no. restore points were created.
  Updating installed Windows the following
  Microsoft .NET Framework 4.5 1 4.5.50938
  Microsoft Office Home and Business 2010...
  Service Pack 2 for Microsoft Office 2010...
  Microsoft driver (keyboard) 21/04/2009
  Microsoft driver (mouse) 21/04/2009
  Driver Microsoft (System) of 21/06/2009...
  Microsoft driver (System) 21/06/2006
  Driver Microsoft (System) of 21/06/2006...
  RALink Technology, Corp. (Net) 02/04/2013 pilot
  Update for Microsoft Windows
  Update for
  Update for
  Well when the restore point was present he says that these things will be deleted that's where I got the list, but as I said the restoration failed and disappeared.
  I have reset my router but my laptop doesn't detect a network and there are usually 10 in the region and it shows nothing. My router is fine, as I use it now with my playstation.
  Please I really need help, how do I get my laptop to detect the wireless network. If someone could give me a few steps to do, please.

  Most laptops have a switch that turns the wifi radio on or off.  Often, it is a combination of the Fn key and one of the F keys.  It may be a physical switch somewhere on the laptop.  See your manual for details.

  If this isn't the problem...

  What is the brand and model of your router?  Almost all wifi routers also have at least one Ethernet port, you can connect your computer to the router with an Ethernet cable and download the right driver for your http://www.asus.com/support wireless card
  Have you tried to "Roll back driver" in the "Driver" tab of your adapter wifi 'properties' in Device Manager?  At the very least, determine which version of the driver is installed, and compare that to the current version on the asus support site.

• Vista one network does. -Cannot access network after the first time it is connected

  I have a network of 4 XP machines 1 XP Pro machine 1 Vista machine at home and a home server system. Everything works fine except the machine Vista seems to be able to access the network once and after that it will be impossible to see the other system or access in any way. Anyone has any idea what exactly is happening?

  This article addresses an issue where the XP computers do not appear in the Vista network map:http://support.microsoft.com/kb/922120.  It can solve this particular problem.

  As far as the server goes, which is beyond the scope of this forum. Please repost in Windows Home Server Forum:http://social.microsoft.com/Forums/en-US/category/WindowsHomeServer/ , where experts in these servers will be happy to help you connect to it.

  I hope this helps.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• HP 190 t and cannot access network after upgrade to win 8

  Upgrade to Windows 8 and cannot access the internet on my desktop HP 190 t.  No driver available on the HP support site.  I can see received/transmitted data between router but that is as far as it goes.   Have ideas or how to get the chipset drivers or should I get another network card?  Everything else seems to work very well.

  I found the problem.  Norton Security Suite does not work with Win 8, causing conflicts.   I have remove the application configured defender and firewall Windows to maintain security until Norton product can support 8 Win.

• iPhone 6 touch id cannot be added after the upgrade ios 9.3.5

  My iPhone6 more ' Touch ID ceased to operate after the sound ' iOS to 9.3.5. This never happened with the previous iOS updates. Soft reboot (button home + power until the display of the apple logo) didn't work. Turn off the two "use Touch ID" for Unlock iPhone & iTunes App Store, then reboot and or soft reboot didn't work. Tried to 'Add a fingerprint', but as soon as it has been exploited, it goes directly to the page saying: 'FAIL' unable to complete installation of contact ID. Back... I even deleted all to restore my backup who had an operation 9.3.4 iOS, but then, I realized that after the restoration, put also got iOS updated! (I'm back to 0). Please help if you have any other fix for this? Thank you.

  Restoring as a NEW phone using iTunes (do not use backup at all).  Adding 3rd party applications, try the contact ID.  If it still does not work, then you have a hardware problem and will need to bring the phone to Apple for the assessment.

  Best,

  GDG

• Vista cannot see network but other machines readers works very well

  Hi all

  Really problem simple and stupid that led to me round the twist that I see not what is causing the problem.

  I have 2 laptops and 2 players on the same network implemented as follows:

  -1 laptop running windows 7.
  -1 laptop running windows Vista
  -1 dedicated NAS connected via Ethernet, which is also a media server
  -1 USB key converted to a NAS by connecting a player to the USB port on the router

  Computer laptop windows 7 can access internet and network drives fine and access the Vista laptop - nothing wrong with this machine.

  The computer Vista laptop can access the internet and a Windows 7 laptop but I am unable to "see" the network drives when you browse the network to map drives.

  As far as I can tell, the two laptops have the same settings and are in the same workgroup between them and the network drives.

  Any help is greatly appreciated

  Thank you

  Grahame

  Hello

  Did you change your computer?

  (1) first of all, make sure that the workgroup name is the same on all computers on the network. In Windows Vista and Windows 7, the default workgroup name is "WORKGROUP". On Windows XP, the name of working group by default on Windows XP-based computers is "MSHOME". On all other versions of XP Professional, it is "WORKGROUP".

  Go to control panel, then network and sharing Center:
  (2) network discovery: WE
  (3) the network value: private
  (4) file Sharing is: on
  (5) public folder sharing: WE
  (6) protected password: OFF

  Disconnect your computer from a network or network drive

  http://Windows.Microsoft.com/en-us/Windows-Vista/disconnect-your-computer-from-a-network-or-network-drive

  View computers and devices on a network

  http://Windows.Microsoft.com/en-us/Windows-Vista/view-computers-and-devices-on-a-network

• Cannot see network adapters

  I am running Windows 7 Professional 64 bit on the computer I want to run VMware Server.  I have no problems with installation and setting up of the guest operating system.  However, it will not see my network adapters on this computer.  I even tried to install on an another Win7 (Home Premium 64-bit) and it has the same problem.  I had to test it on a professional (32-bit) Windows XP computer until I was able to confirm that it doesn't detect network cards (you can see the cards on this machine very well, but IE won't let me access the Server web browser interface).

  When I open the virtual networks management program, I only have the option 'bridge to an automatically chosen adapter' and I can not uncheck the option "automatic gateways.

  When using NAT networking, I ping addresses (for example, www.google.com), but I can't visit a Web site.

  Someone, help please?

  and I can not uncheck the option "automatic gateways.

  then the installation failed - as expected, by the way.

  Windows7 - 64 is not a host-OS supported for VMserver

  _________________________

  VMX-settings- WS FAQ -[MOAcd | http://sanbarrow.com/moa241.html]- VMDK-manual

• ESXi 5 cannot see storage after installation

  I recently downloaded an eval of ESX, which included ESXi 5.0 60 days. I installed it on a test server, but there the LVM is not listed under data warehouses that shows only a data store that is the OS disk (LVM is on a separate RAID array).

  I tried SSHing on the server but not from the usual commands for example lvdisplay, pvdisplay, etc. works, I can't manage it with vCentre because when I try to register I get: "VMware ESX and VMware ESXi servers are not compatible with vSphere Client Web 5.0.0."

  How am I supposed to manage storage?

  Download and install the vSphere client. Access the host through it. You can download the form available in webaccess hyperlink vSphere client.

  https:// .

  Once connected to the host, select storage in the Configuration tab.

  Select Add storage.

  storage RAID or LVM physical should be visible here.

• iPhone only 6 more will not restore after downloading the new update.

  I was prompted to download the new update tonight once I started it, the download started like any other. Once restarted my iPhone, the iPhone connect to iTunes screen appeared. I connected my iPhone to my MacBook Pro and selected the "Update" option, the update has started to download on iTunes. Long story short, the iPhone will not update, I got a prompt that displays "an unknown error has occurred." I also tried to restore the iPhone and that also does not work. I also tried to put in DFU mode to restore via iTunes and that no longer works. I had problems with my iPhone with it restarts randomly, apps opening themselves and the flicker of screen and the freezing of old simply phone on a two screen tones. This is an iPhone brand new I just got last Monday. Help, please!

  Try troubleshooting help here > fix updated iOS and iTunes restore errors

• No network after 4.02 (491587) update

  When I upgraded to 4 day it was out, everything seems to work perfectly.  But 4.02 broke my Windows 7 computer virtual network card.

  1. the automatic update does not work, it crashed, and the Fusion dock icon went to the broken default app lost look

  2. I had to download 4.02 full installation, seemed to work but now the network card in Windows 7 VM believes that the network cable is unplugged.

  Your credit upgrde first 4 executed mainly GUI of much better and faster response.  I've been a happy customer, but 4.02 totally destroyed my work schedule!

  I tried NAT, bridged, all options; no luck.  I deleted the Windows 7 device driver to force a reinstall; no luck. Tried to re install tools VMwre; no luck.

  What is wth 4.02.

  Log in-app upgrade VMware crash attached.

  Some time, the network failed because the process of the network does not work. Open the activity monitor and filter if there are 6 vmnet process. (vmnet-netifup, vmnet-dhcpd, vmnet-bridge, vmnet-natd(8)) Usually, a reboot of the fusion of host and relanuch Mac will bring back all these processes, please give it a try.