iPod dropped in the water aid

Similar Questions

• Excursion to Smartphones blackBerry dropped in the water...

  Hey, I dropped my blackberry tour in the toilet for a few seconds, took the battery and separated dried both. When I got home, about two hours later, I put my phone in rice dry and it has been sitting for about two days. I took the lead by about a day and tried to start up my phone. my phone at all turns. It is completely fried? could it be just the battery? but my phone was also almost at low battery when I dropped it in the toilet. What should I do?

  Give him a full five days IN rice and no more check it out to see if it works.

  Yes, you could have fried, but maybe not. After five days, the device connected to a cable from charger from wall outlet and then replace the battery. Less than 10 minutes, you will know whether or not it is fried.

  Good luck!

• I dropped my iphone 4s in the water, but it still works?

  I actually dropped my phone in the water before, but it worked fine afterwards, despite the fact that I have did nothing. I went in the bathroom again today and it seemed to work very well and I don't think anything of it. All sounds have worked, the screen and the brightness seemed fine, and all the buttons work. My wifi worked not briefly, but the wifi in my house is a little wobbly and I turned it works and it was fine. I used it for more than two hours later and it was fine, until I noticed water under the screen. I immediately looked up what I must do, turned my phone off, took out the sim card and began painstakingly dry with a hair dryer (I don't have any rice or silica gel), paying special attention to the battery, but also an opening in the phone. The hair dryer was weak, I kept it at a distance, and I followed it constantly for that phone don't fire no. I skipped, it regularly for about 20-30 minutes, turned to the monitor, and the brand of water has been growing (its in the half top of the screen) and it seems to have disappeared, but I wonder if the water could simply scattered. I have it turn on and off several times and it always seems fine.

  I need to know if you think that the phone will survive. Also, I can't afford a new phone or to get it fixed now, so if you have advice that can be performed by an amateur at home, then I'd love to hear them. Thank you.

  I think that your phone will probably survive if you used a hair dryer on low, do at least 1 iCloud backup every week, but if you get a new phone, I'm sorry.

• iPhone 6s thrown into the water now get no service?

  Hello

  I have an iPhone 6s I dropped in my sink Fortunately it still works (lights etc) because she was only in it for no more than 20 seconds!

  So it works but the only problem is, is that im getting no service, even though I had full signal before it was submerged I tried taking the SIM out, leaving the phone to dry overnight, then I put my sim card, I started it and he remained at say no sim and after a few minutes It says no service? :

  Water and electronics don't go well together. Even if the iPhone can still turn it on, the water probably and most likely caused one short-circuit somewhere else in the electronics and is causing problems with the cellular antenna. Its probably shorted out.

  Other it has an Apple Store for warranty replacement output, there is not much to do.

• How to stop the water flow?

  Hello

  I need to make the water from the shower, when you click on shower.

  And the water should stop after 5 seconds.

  The code is below.

  Water flows well. But I fail to stop it.

  I added a timer that starts when the shower is clicked. And must stop the flow of water after 5 seconds have elapsed.

  With the lines

  If (stop = true)

  {

  break;

  trace ("Break");

  }

  It looks like the for loop breaks right from the start, from the first second. But not completely, somehow 1 or 2 drops are fluid.

  Without these lines, nothing happens when the time is up (5 seconds click on the shower). The water just flows.

  Can anyone help? How to stop water flowing after 5 seconds and cleaning of the table and stage of water drops?

  Thanks in advance!

  import flash.display.MovieClip;

  import flash.events.Event;

  import flash.utils.Timer;

  import flash.events.TimerEvent;

  var WatertropArray: Array = new Array();

  var WaterArea01: MovieClip = new WaterArea();

  var WaterBorder01: MovieClip = new WaterBorder();

  var timer: Timer = new Timer (1, 5000);

  var stop: Boolean;

  var i: uint;

  Shower.addEventListener (MouseEvent.CLICK, waterFlowStart);

  function waterFlowStart(event: MouseEvent): void

  {

  addChild (WaterArea01);

  WaterArea01.x = WaterArea00.x;

  WaterArea01.y = WaterArea00.y;

  WaterArea01.alpha = 0;

  addChild (WaterBorder01);

  WaterBorder01.x = WaterBorder00.x;

  WaterBorder01.y = WaterBorder00.y;

  WaterBorder01.alpha = 0;

  Stop = false;

  timer.addEventListener (TimerEvent.TIMER, waterFlowEnd);

  Timer.Start ();

  addWaterdrops();

  Shower.removeEventListener (MouseEvent.CLICK, waterFlowStart);

  }

  function addWaterdrops(): void

  {

  for (var i: uint = 0; i < 100; i ++)

  {

  waterDrop var: MovieClip = new Waterdrop();

  addChild (waterDrop);

  waterDrop.x = Math.round (Math.random () * stage.stageWidth / 1.5);

  waterDrop.y = Math.round (Math.random () * stage.stageHeight / 3);

  waterDrop.alpha = 0;

  waterDrop.rotation = - 12;

  WatertropArray.push (waterDrop);

  trace ("drops of water added");

  moveWaterdrops();

  }

  }

  function moveWaterdrops(): void

  {

  waterDrop00.addEventListener (Event.ENTER_FRAME, water flow);

  }

  function waterFlow(event: Event): void

  {

  for (var i: uint = 0; i < WatertropArray.length; i ++)

  {

  WatertropArray [i] there = 8;

  WatertropArray [i] .x += 5;

  trace (i);

  If (WatertropArray [i] .hitTestObject (WaterArea01))

  {

  WatertropArray [i] .alpha = Math.Random ();

  WatertropArray [i] .scaleX = Math.Random ();

  WatertropArray [i] .scaleY = .scaleX [i] WatertropArray;

  }

  If (WatertropArray [i] .hitTestObject (WaterBorder01) |) WatertropArray [i] .x > stage.stageWidth | WatertropArray [i] there > stage.stageHeight / 2).

  {

  WatertropArray [i] .x = Math.round (Math.random () * stage.stageWidth / 1.5);

  WatertropArray [i] there = Math.round (Math.random () * stage.stageHeight / 3);

  . Alpha WatertropArray [i] = 0;

  }

  If (stop = true)

  {

  break;

  trace ("Break");

  }

  }

  }

  function waterFlowEnd(event: TimerEvent): void

  {

  trace ("TIME OVER");

  Stop = true;

  stoppTrue();

  }

  function stoppTrue(): void

  {

  for (var i: uint = WatertropArray.length; i > WatertropArray.length; i-)

  {

  Remove (i);

  }

  }

  function remove(idx: int)

  {

  removeChild (WatertropArray [idx]);

  WatertropArray.splice (idx, 1);

  trace ("removed");

  removeChild (waterDrop00);

  trace (i);

  }

  I should be an int, not a uint.

• Apple Watch waterproof to the water

  I must do something before I want to go swim with my series 2 Watch? Lock it?

  Hello

  Swimming workouts

  Begin a swim practice in the application of the workout on Apple Watch series 2 models automatically activates the lock of the water, which locks the screen to avoid accidental interactions during your workout.

  To complete your workout and to evacuate all the water:

  • Press the digital Crown and side button at the same time (which makes a break from the workout).
  • Turn the digital Crown, which opens the screen and erases all the water inside of the watch (it can make a sound).
  • Forehand and press end.

  Other swimming

  If you plan to get your Apple Watch series 2 wet in other circumstances that when training of swimming - as to the course of General wear in a pool - you can manually lock the screen first and then drain the water from the speaker subsequently:

  • Slide up from the bottom of the face of the watch to open Control Center > tap water from lock to lock the screen.
  • When you're done: turn the digital Crown to unlock the screen and drained the water from the speaker.
  • The lock can also be unexpected water activated and unlocked immediately after exposure to the water.

  After bathing, make sure to clean your Apple Watch series 2 by rinsing them with hot water from the tap. Watch and the band should be dried with a non abrasive and non fluffy cloth.

  Strips of leather and stainless steel (Milanese Loop and Bracelet links) are not water resistant, so should not be worn when swimming.

  More information:

  Work with your Apple Watch - Apple Support

  On the resistance to water Apple Watch - Apple Support

  https://help.Apple.com/watch/#/apd707b42a5e

• Series 2: Push the water

  There will be a way to push the water through the speaker without start/end an exercise (swimming)? An App? Maybe I wear the watch in the pool/shower or just wash my hands with a lt of water.

  "If air pushed by the speaker can get out, the water will be. So the speaker vibrates to push the air out, forcing the water out too. The user can turn the digital Crown to achieve, as a representative of Apple showed me yesterday. »

  Here > https://news.fastcompany.com/how-apple-watch-series-2-pushes-water-out-of-the-sp eaker-wind-4018739

• If I have the first generation iWatch I'll be able to get the update for new applications and look at faces?  I know that I couldn't display or the waterproof function to the water.

  If I have the first generation iWatch I'll be able to get the update for new applications and look at faces?  I know that I couldn't display or the waterproof function to the water.

  Hello

  The next operating system update, watch OS 3, will be available for all Apple Watch models, including the first generation watches.

  We should go out on 13 September, after which it can be installed by following the steps detailed here:

  • Update the software on your Apple Watch - Apple Support

  More information:

  http://www.Apple.com/Watchos/

• Thunderbird does not all files except "inbox." and against the info 'aid', there is NO 'account settings' under 'Tools' &amp; I have the latest version of T.

  Thunderbird does not all files except "inbox." and against the info 'aid', there is NO 'account settings' under 'Tools' & I have the latest version of T. I just need to download the SENT MESSAGES, Inbox not only.

  Re: Where is 'account settings '.
  If you do not see 'Tools', then you do not have your active 'Menu Bar'.
  See picture below on the activation of all the toolbars make life easier.

  Different methods of location of the 'account settings ':
  Via the toolbar "Menu Bar":

  • Tools > accounts settings

  Through the pane of folders:

  • Right-click on the name of the e-mail account in the folders pane, and then select "settings".

  Via "Menu Icon.

  • Menu icon > Options > account settings

  Re: I need to download sent Messages Inbox not only.
  E-mail accounts IMAP see a remote view of the files on the server.
  You subscribe to view these folders in Thunderbird.
  You synchronize directories subscribed for a copy in Thunderbird.
  What you do in a folder for example imap: delete, will occur on the server, so viewing via webmail or Thunderbird folders appear identical.

  However, in your case, it seems that you have created a POP e-mail account.
  E-mail POP accounts can only connect to Inbox server and download server Inbox for the Thunderbird Inbox pop e-mail account.
  It's not a quirk of Thunderbird; This is how all Pop mail represents the work.

  There is a work around to get "sent" in the folder mail sent from server in Thunderbird. You just do it once, because when you send it through Thunderbird, it will put the e-mails in the folder sent TB pop mail account and not on the server.

  Thunderbird creates a "Sent" folder when first send you an email.
  So, if you have not yet sent an email, please send one, even if only to yourself.

  Then, move all inbox emails in the appropriate folders.
  You can create new folders to organize them.

  How to create a new folder:

  • Right-click on the name of the e-mail account, and then select "new folder."
  • Give an appropriate file name and click "create a folder".

  When the Inbox is empty:

  • Logon to the Web e-mail account by using a browser.
  • Move all emails "Sent" in the "Inbox".

  In thunderbird:

  • Click on 'Get the message'

  all the "Sent" emails must get downloaded from the server Inbox anto your Inbox in Thunderbird.

  • Then move all your emails in the 'Sent' Thunderbird folder.

  You should now have all these emails downloaded from the server and display in Thunderbird.

• iPhone fell in the water

  I have an iphone 6 and he fell into the water. Anyone have any suggestions about how to fix it? Please help me.

  I think that you can take your hair dryer to dry, and it can be used forever!

• Is there a way to fix and find pictures of my ipod which has suffered water damage

  My ipod fell in the pool and had been before having more problems with heating, and as he fell the pool is not lit. He fell in the pool for more than a year (about a year and 2 months) and since then has been in the rice that I tried fix, but I think it only made things worse

  Unless you had iCloud Photo Stream on or if you have an iTunes or iCloud backup to restore-these images are gone I'm sorry

• When is it safe to charge or backup an iPhone 6 after it was plunged into the water?

  When is it safe to try to load or save an iPhone 6 that fell in the water? It shows that he needs a load when you press the power button.

  You should not try to turn it on or charge it for a week or two.

  If it's on, or you have enabled, then the damage is done and it probably doesn't matter now.

• How much time does it take for my ipod to connect the itune after putting in disc mode?

  How much time does it take for my ipod to connect the itune after putting in disc mode?

  my ipod displays 'do not disconnect' for half an hour already, but my itune cannot always detect my ipod (as itune will pop up once I have connected my ipod normally).

  What is your real question?  Why you connect the iPod to your computer to disc Mode?

  In addition, it would be useful to know if you are using a Mac or a Windows PC?  If Windows, what version?

  If iTunes does not open automatically (when you connect the iPod), what happens when you run it manually?

• Is it possible to transfer music from an ipod 4G for the new model?

  I got my ipod touch 4g since 2010 and I was too cheap to upgrade. Now that the battery life has been emptying faster than ever and high sleep button no longer works, I think its time to finally switch to this new model.

  The bad part is that for the last 6 years, I have collected 12.6 GB worth of music on my ipod touch with nearly 85 per cent of it related to the device itself and not on my pc. I usually have the removed from the computer as Itunes would always keep always on my ipod touch as long as the songs were always listed in the library.

  I was wondering is there a way to transfer my music from my old ipod touch to the new model?

  Your i-device was not designed for unique storage of your media. It is not that a transfer backup device and media has been planned with you keep a master copy of your media on a computer that is in itself independently supported against loss.  To use a device with a different configuration, you pass the old library from a computer or a backup directly in the new configuration, not the device to the library. Synchronization of media isn't a way, computer to the device, update the contents of the device to the content on the computer, update or restore the content on a computer. The exception is iTunes Store purchases that can be transferred to a computer.

  Redownload or transfer your iTunes Store purchases an iPhone, iPad or iPod to computer - https://support.apple.com/en-us/HT201267 - 'this feature only works for content purchased from the iTunes Store. From iOS9 is more apps that now need to be re-downloaded directly from the store.

  To transfer other items from an i-device to a computer, you will need to use third-party commercial software.  See this document in turingtest2: recover your iTunes library from your iPod or device iOS - https://discussions.apple.com/docs/DOC-3991 even this method can fully recover what you originally had in the library. For example, in order to save space during synchronization if you had converted music files at a lower rate, or photos at a lower resolution, it is these lower quality files that will pick you up.

  If you subscribe to the Apple music, titles that are not part of the content that you have purchased or downloaded may not be transferred and must be downloaded directly from iCloud.

• How can I get my iPod Touch on the way of recovery without loss of data?

  Hello

  My iPod touch 4th generation shows a cable Apple USB pointing towards the iTunes logo.

  I have not jailbroken it or fallen to set the mode of recovery, and when I open iTunes it comes up with the message saying that it has detected an iPod in recovery mode and I can't use it with iTunes unless I restore my iPod.

  Of course, I don't want to erase all the 50 GB of music I stored on I have not saved recently.

  Is it possible for me to get my iPod out of the recovery mode without restore me or lose my data?

  Thank you very much

  Kieran

  iPod Touch 4th generation 64 GB iOS 6.1.6

  12.3.3.17 iTunes 64-bit on Windows 10

  

  No, the iPod needs to be restored and then deleted.

  However, with iOS 6 you can be able to get some data fom restored via iPod

  How to perform a recovery of the iPad for photos, videos

  Dr. Phone to iOS recovery - PC only

  Data rescue tool all autour for Apple iPod