Similar Questions

• Script to check the version of Cisco VEM on ESXi host

  Hallo,

  I need help, a script to check and report in a CSV file, the version of Cisco Nexus 1000v VEM on all ESXi hosts connected to a vCenter.

  Basically, "vem version - v" but for all the ESXi hosts connected to a vCenter.

  Thank you

  Joseph

  I suspect you could use PowerShell v1, in this version that the Export-Csv has not had the UseCulture parameter.

  Try to run the script without this parameter.

  But I would strongly suggest to upgrade your version of PowerShell (v3 is available)

• See the version for Cisco Blocker

  Hello

  As I am not really tech savvy here, we currently have a problem where we need to check a serial number for blocker of Cisco. However, the customer says that they didn't show version and we provided instead the system state information. However, her, we can derive the correct serial No. Anyone who is familiar with how to interpret the State of the system to get the correct serial number for Cisbo Blocker? Or are there other options that the customer can give us to get the correct serial number?

  I enclose the status of the system provided by the customer.

  Thank you

  Cathy

  Spare part

  BV277F1 is a valid serial number for blocker of Cisco.

• Does anyone know if the version of Cisco Clean Access Server supports the 4.1 (8) SHA - 256 signed SSL certificates?

  Yes, I know they are very old servers and technically, we should move away from CASES in total. But unfortunately, it's an environment I inherited, and I am now dealing with issues.  Because of the requirement to move away from sha - 1 signed certificates that I need to replace my existing certs, certs signature sha-256.  But before I do that I would like to know if anyone knows if CASE version 4.1 (8) supports SHA - 256 certificates?  I did check the release notes, but there is no mention of the supported versions of SHA, etc..  I tried TACS but no joy there either, etc..

  Hello Rafael,.

  SHA - 2 signed the certificate of support was added in 4.7.2 for SCS and CAM.

  We have filed a default document to have it documented in the release notes.
  CSCud99946    Note of support for the NAC should say we support certs of SHA - 2

  Kind regards

  Jousset

• How to discern autonomous and lightweight to "see the version.

  It's 'see the version' for Aironet 1240AG.

  He was LightweightAP.

  But now, I guess it's AutonomousAP, because I have active autonomous.

  So how discerm?

  Is independent "flash:/c1240-k9w7-mx.124-21a.JY/c1240-k9w7-mx.124-21a.JY"?

  = ~ = ~ = ~ = ~ = ~ = ~ = ~ = ~ = ~ = ~ = ~ = PuTTY connect 2010.08.25 18:10:15 = ~ = ~ = ~ = ~ = ~ = ~ = ~ = ~ = ~ = ~ = ~ =.
  See the version
  Software Cisco IOS, C1240 Software (C1240-K9W7-M), Version 12.4 JY (21 a), RELEASE SOFTWARE (fc1)
  Technical support: http://www.cisco.com/techsupport
  Copyright (c) 1986-2010 by Cisco Systems, Inc.
  Updated Thursday, April 28, 10 11:14 by prod_rel_team

  ROM: Bootstrap program is C1240 boot loader
  BOOTLDR: Version of bootloader (BOOT-C1240-M) C1240 12.3 (7) JA1, RELEASE SOFTWARE (fc1)

  MCBR_AP01 uptime is 1 day, 22 hours, 58 minutes
  System to regain the power ROM
  System image file is "flash:/c1240-k9w7-mx.124-21a.JY/c1240-k9w7-mx.124-21a.JY".

  This product contains cryptographic features and is under the United States
  States and local laws governing the import, export, transfer and
  use. Delivery of Cisco cryptographic products does not imply
  third party approval to import, export, distribute or use encryption.
  Importers, exporters, distributors and users are responsible for
  compliance with U.S. laws and local countries. By using this product you
  agree to comply with the regulations and laws in force. If you are unable
  to satisfy the United States and local laws, return the product.
  -More-
  A summary of U.S. laws governing Cisco cryptographic products to:
  http://www.Cisco.com/WWL/export/crypto/tool/stqrg.html

  If you need assistance please contact us by mail at
  [email protected] / * /.

  Cisco AIR-LAP1242AG-A-K9 (PowerPCElvis) Prozesseur (revision A0) 24566K / 8192K bytes of memory.
  Card processor ID FTX1202B316
  PowerPCElvis CPU at 262 Mhz, revision number 0 x 0950
  Last reset of tension
  1 interface FastEthernet
  2 802.11 radios

  32K bytes memory simulated by flash not volatile configuration.
  Basic Ethernet MAC address: 00:1: A1:FD:54:14
  Part number: 73-9925-06
  Kit numbered PCA: 800-26579-05
  Revision number of PCA: A0
  Serial number of PCB: FOC12010GQ4
  Top Assembly part number: 800-29151-02
  Top of page the Assembly serial number: FTX1202B316
  -More revision number - top of page: A0
  Product/model number: AIR-LAP1242AG-A-K9

  Configuration register is 0xF

  Fortunately, it's actually very easy.  If the AP is loaded with a stand-alone image, it will be a k9w7 if she a CUWN image, it will be a k9w8.

• This version of Cisco Adaptive Security Appliance Software Version 9.6 (1) 5 is affected by Cisco Adaptive Security Appliance SNMP Remote Code execution vulnerability and Cisco Adaptive Security Appliance CLI Remote Code execution vulnerability of

  This version of Cisco Adaptive Security Appliance Software Version 9.6 (1) 5 is affected by Cisco Adaptive Security Appliance SNMP Remote Code execution vulnerability and Cisco Adaptive Security Appliance CLI Remote Code execution vulnerability of

  Hi vrian_colaba,

  You can take a look at cisco's Advisory here:

  https://Tools.Cisco.com/Security/Center/content/CiscoSecurityAdvisory/CI...

  Fixed versions

  Cisco ASA Major Release	First version fixed
  7.2	Affected; migrate to 9.1.7(9) or later
  8.0	Affected; migrate to 9.1.7(9) or later
  8.1	Affected; migrate to 9.1.7(9) or later
  8.2	Affected; migrate to 9.1.7(9) or later
  8.3	Affected; migrate to 9.1.7(9) or later
  8.4	Affected; migrate to 9.1.7(9) or later
  8.5	Affected; migrate to 9.1.7(9) or later
  8.6	Affected; migrate to 9.1.7(9) or later
  8.7	Affected; migrate to 9.1.7(9) or later
  9.0	9.0.4 (40)
  9.1	9.1.7(9)
  9.2	9.2.4 (14)
  9.3	9.3.3 (10)
  9.4	9.4.3(8) ETA 26/08/2016
  9.5	9.5 (3) ETA 30/08/2016
  9.6 (DFT)	9.6.1 (11) / 6.0.1(2) FTD
  9.6 (ASA)	9.6.2

  5 9.6 (1) is not part of the fixed versions, this means that is assigned for the SNMP Remote Code execution vulnerability.

  Cisco Adaptive Security Appliance CLI Remote Code vulnerability to run you can also take a look at cisco's Advisory here:

  https://Tools.Cisco.com/Security/Center/content/CiscoSecurityAdvisory/CI...

  Fixed versions

  The following table shows the first software versions that include fixes for this vulnerability (9.6 is not affected)

  Cisco ASA Major Release	First version fixed
  7.2	Affected, migrate to 8.4 (3) or later
  8.0	Affected, migrate to 8.4 (3) or later
  8.1	Affected, migrate to 8.4 (3) or later
  8.2	Affected, migrate to 8.4 (3) or later
  8.3	Affected, migrate to 8.4 (3) or later
  8.4	8.4 (3)
  8.5	Affected, migrate to 9.0 (1) or later version
  8.6	Affected, migrate to 9.0 (1) or later version
  8.7	Affected, migrate to 9.0 (1) or later version
  9.0	9.0 (1)
  9.1	Not affected
  9.2	Not affected
  9.3	Not affected
  9.4	Not affected
  9.5	Not affected
  9.6	Not affected

  Hope this info helps!

  Note If you help!

  -JP-

• Cisco 2911 and ASA 5512 remove double NAT

  Greetings,

  I have 2 subnets on Cisco 2911 router

  192.168.3.0/24 and 192.168.1.0/24

  3rd network 192.168.4.0/24 is natting internal interface to the modem for internet access. creating 2 NAT (NAT in router) and NAT in Modem

  I just bought Cisco ASA 5512, no chance I could remove the Cisco 2911 router NAT and set the default gateway for Cisco ASA?

  Yes you are right...

  You must ensure that you get the routed LAN traffioc to hit inside the interface ASA in ASA, you can do PAT/NAT to access...

  Concerning

  Knockaert

• What browser uses tide to load URL files? How to check the version of the browser

  We intend to migrate to sharepoint list files. When I insert the sharepoint url in the folders tab, it loads perfectly. When I click on the hyperlink on the page, I'm running script pop - pup - "an error has occurred in the script on this page" - class not registered (loaded scriptFiles undefined-microsoft Jscript runtime error).

  This clickable link on the page works perfectly in IE or chrome. I want to know what browser and using the version of tide. How do I check this? If I had to change the browser settings where can I do. Or if someone has encountered a similar problem, please suggest the fix.

  Thank you!

  We also used Citrix for our 5.3.1 version and it works for us (web sites and internal sharepoint 2010 & 2008 version)

  A couple of things to try

  1. customer install locally try again
  2. Permissions on wiki sharpoint Site Actions... Site permissions. The permissions of site url must end with /_layouts/user.aspx or ask your administrator SharePoint to read to users or to groups of ads that should consult the pages on the wiki (which is what we did)

  I can't speak for 5.2.2 and probably that is not supported by Cisco

  CISCO, support for YOUR extended 5.3.1 until January 31, 2016.

  Installation of the tide 6 as soon as possible,

  Marc

• What version of Cisco IP Communicator supports to UC520?

  Model: UC520

  IOS version: 12.4 (20) T4

  CME: 7.0

  What version of Cisco IP Communicator supports to UC520 with CME7.0?

  Release Notes of IP Communicator is not included CME7.0 in the supported versions.

  http://www.Cisco.com/en/us/products/SW/voicesw/ps5475/prod_release_notes_list.html

  Please advise, thank you.

  Any version.

  However, you must update UC500, because it is very old.

• The upgrade of Cisco IDS 4235

  Currently, we are conducting 5.1.3 GIS 257. I know I'm behind and want to also include DST updates. If I switch to 5.1.4 or 5.1.5 What is the version that I will need to upgrade to these Service Packs? 5.1.3's 257 enough?

  Thank you

  Dwane

  You can go to 5.1. (5) .. minimum required for this upgrade is 5.0 (1) for users of CLI and IDM. This Service Pack includes the update of the Signature S272. With regard to the IDS/IPS devices, its always preferable to run on the latest versions.

  Kind regards

  Maryse.

• Router RV042 firmware Upgrade older and what is the Version 1, 2, 3

  We have a CISCO RV042.  We are about to begin a service IOPV with Joseph who declare:

  The RV042 is a wired router that requires no adjustment configuration for versions of firmware, that we tested.    NOTE: The Version 1 and 2 are compatible. Version 3 is NOT.  Revised firmware: 1.3.12.6 | 1.3.12.19

  Our router firmware is: 1.3.8.2 (February 12, 2007 10:43:08)

  We can upgrade to 1.3.12.6 or 1.3.12.19?  What is Version 1, 2 and 3?

  Hi David, V1 2 and 3 are the versions of the released router hardware. The best, I can say that the 1.3.13.02 is the last for routers V01.

  -Tom
  Please mark replied messages useful

• The incomplete 1941W Cisco router configuration

  Good day all.

  I was running a business of small ecommerce for the last 5 years on a Linksys wireless router. Now that I have more than 14 posts and 6 networked printers, it was time to take a step towards the top.

  I bought a 1941W SRI CISCO to take us to the Gigabit speed in the next decade with a CISCO switch. I assume that the 1941W, although robust with scalability, would provide the installation of it, simple as the product Linksys (Cisco) or at least a simple 1-2-3 How to get basic connections made. I was wrong and now I find that I have some difficulty to negotiate Internet on the router again.

  Included below is my config NVRAM. I hope someone could tell where I can have a few gaps in my config.

  Please note: this config is derived from an example on the net that seemed simple enough, so if you find yourself asking, "why did do that?", I hope that this provides the perspective.

  TEST router configuration
  28/07/2010

  Objective: Complete the basic configuration to connect (and ping) to the internet
  Problem: Cannot conect to the internet; Incomplete suspected configuration; Maybe bad config NAT or DNS issue
  Comments: In the process.

  TEXT OF HYPERTERMINAL CONNECTION TO THE CONSOLE:

  User access audit

  User name: admin
  Password:

  TESTROUTER > activate
  Password:
  TESTROUTER #ping 8.8.8.8

  Type to abort escape sequence.
  Send 5, echoes ICMP 100 bytes to 8.8.8.8, time-out is 2 seconds:
  .....
  Success rate is 0% (0/5)

  TESTROUTER #show config
  With the help of 2615 off 262136 bytes
  !
  ! 01:33:34 CST configuration was last modified Thursday, July 29, 2010 by admin
  !
  version 15.0
  no service button
  tcp KeepAlive-component snap-in service
  a tcp-KeepAlive-quick service
  horodateurs service debug datetime msec show-time zone
  horodateurs service log datetime msec show-time zone
  encryption password service
  !
  hostname TESTROUTER
  !
  boot-start-marker
  boot-end-marker
  !
  logging buffered 16000
  recording console critical
  enable secret 5 XXXXXXXXXXXXXXXXXXXXXXXXXX
  enable password 7 XXXXXXXXXXXXXXXX
  !
  AAA new-model
  !
  !
  AAA authentication login default local
  the AAA authentication enable default
  !
  !
  !
  !
  !
  AAA - the id of the joint session
  iomem 10 memory size
  clock timezone CST - 6
  Service-module wlan-ap 0 autonomous bootimage
  !
  No ipv6 cef
  no ip source route
  inaccessible 2000 IP icmp rate-limit
  IP icmp rate-limit unreachable DF 2000
  IP cef
  !
  !
  !
  !
  no ip bootp Server
  no ip domain search
  8.8.8.8 IP name-server
  IP-server names 8.8.4.4
  name of the IP-server 209.18.47.61
  name of the IP-server 209.18.47.62
  Authenticated MultiLink bundle-name Panel
  !
  !
  !
  license udi pid CISCO1941W-A/K9 sn XXXXXXXXXXX
  ISM HW-module 0
  !
  !
  !
  admin password username 7 XXXXXXXXXXXX
  !
  !
  !
  !
  !
  !
  interface GigabitEthernet0/Wlan-0
  Description interface connecting to the AP the switch embedded internal
  Shutdown
  !
  interface GigabitEthernet0/0
  Description of connection to the internet to transfer Ethernet/fiber TWC (ISP)
  address IP AA. BB. CC.149 255.255.255.0
  IP access-group 115 to
  no ip unreachable
  no ip proxy-arp
  NAT outside IP
  IP virtual-reassembly
  no ip-cache cef route
  no ip route cache
  automatic duplex
  automatic speed
  No cdp enable
  !
  wlan-ap0 interface
  description of the Service interface module to manage the embedded AP
  no ip address
  ARP timeout 0
  No mop enabled
  No mop sysid
  !
  interface GigabitEthernet0/1
  Internal description of the connection to the local network
  IP 10.10.10.1 255.255.255.0
  IP access-group 116 to
  no ip proxy-arp
  IP nat inside
  IP virtual-reassembly
  no ip-cache cef route
  no ip route cache
  automatic duplex
  automatic speed
  No cdp enable
  No mop enabled
  !
  interface Vlan1
  no ip address
  Shutdown
  !
  IP forward-Protocol ND
  !
  no ip address of the http server
  no ip http secure server
  !
  IP nat inside source list 1 interface GigabitEthernet0/0 overload
  IP route 0.0.0.0 0.0.0.0 AA. ABM CC.1
  IP route 0.0.0.0 0.0.0.0 GigabitEthernet0/0
  !
  access-list 1 permit 0.0.0.0 255.255.255.0
  access-list 115 deny ip 127.0.0.0 0.255.255.255 everything
  !
  not run cdp

  !
  !
  control plan
  !
  !
  Line con 0
  line to 0
  line 67
  no activation-character
  No exec
  preferred no transport
  transport of entry all
  transport output pad rlogin lapb - your MOP v120 udptn ssh telnet
  line vty 0 4
  password 7 XXXXXXXXXXXXXX
  !
  Scheduler allocate 20000 1000
  end

  TESTROUTER #.

  END OF HYPERTERMIAL TO THE TEXT OF THE CONSOLE

  Thanks in advance to those who consider a response.

  Daniel

  Daniel

  You have a LCD 115 on the external interface and it is just a line in this acl which is a refusal. Be aware that an acl has implicit deny all the end anyway so basically that this acl blocking all incoming which responses return icmp (ping) traffic. Because you run the command ping to the router using an IP address not not a DNS then NAT or DNS name is a problem at present.

  I suggest that rewrite you the acl - 115

  access-list 115 permit icmp host 8.8.8.8 entire echo response

  and test again with your ping. If it works then it's the acl that is the problem and you need to write your acl so that is what you want to allow before that you want to deny.

  Jon

• SSL VPN may be configured on the router from Cisco 881/K9?

  I'm now confused if SSL VPN can be configured on the router from Cisco 881/K9.

  Please someone advise me.

  If Yes, for only 5 users, what I need to buy the license or license is supplied with the router?

  Thank you.

  Yes, and you need a license:

  FL-WEBVPN-10-K9

  License SSL VPN functionality for up to 10 users (incremental), to 12.4 T based only IOS versions

  FL-SSLVPN10-K9

  License SSL VPN functionality for up to 10 users (incremental) for the only based 15.x IOS versions

• Version of Cisco ACS 5.1.0.44.3 integrate with active directory server from Microsoft windows 2012?

  Version of Cisco ACS 5.1.0.44.3 integrate with active directory Microsoft windows 2012 R2 server?

  Unfortunately, it does not support R2 2012

  5.1 ACS supports all editions of:

  Windows Active Directory (AD) 2000

  Windows AD 2003

  Windows AD 2003 R2

  Windows AD 2008

  Source

  Windows AD 2012 R2 is supported after ACS 5.5 patch 1 and following.

  Source

  Please find below the steps to go from 5.1 to 5.5 hotfix 1:

  STEP	FILE	COMMAND
  Apply the 5.1 patch 6	5-1-0-44 - 6.tar.gpg	ACS patch install repository 5-1-0-44 - 6.tar.gpg ftp_repository_name
  Apply 5.3	ACS_5.3.0.40.tar.gz	application upgrade ACS_5.3.0.40.tar.gz ftp_repository_name
  Apply the patch 5.3 8	5-3-0-40 - 8.tar.gpg	ACS patch install repository 5-3-0-40 - 8.tar.gpg ftp_repository_name
  Apply the sharp Patch	Pointed-PreUpgrade-CSCum04132-5-3-0-40.tar.gpg	ACS patch installs Pointed-PreUpgrade -CSCum04132- 5-3-0 - 40.tar.gpg repository ftp_repository_name
  Apply 5.5	ACS_5.5.0.46.tar.gz	application upgrade ACS_5.5.0.46.tar.gz ftp_repository_name
  Apply the patch 5.5 1	5-5-0-46 - 1.tar.gpg	ACS patch install repository 5-5-0-46 - 1.tar.gpg ftp_repository_name

  Best regards ~ jousset

• How to display the version of ESX VMwave

  I have a chassis CISCO UCS blade with 4 blades (all B200 M4) and I need to display the installed VMware / works on each of vSPhere 5.5 Web Client.

  Thank you

  GlenG

  Check if help: VMware KB: determine the version number of VMware ESX/ESXi and VMware vCenter Server

  Determine the version of ESX/ESXi number using the Web Client vSphere

  To determine the build number of vCenter Server using the Web Client vSphere:

  1. Log the Web Client vSphere.
  2. Click home.
  3. Click on the hosts and Clusters.
  4. Expand the data center.
  5. Expand the cluster.
  6. Click on the ESXi host.
  7. Click the contents tab
  8. Under Configuration, there will be a field of ESX/ESXi Version: