IPSEC VPN site to site on Transparent mode

Hello

The new version of the OS of the SAA does support IPSEC site-to-site VPN for partners on more Transparent?

Thank you very much

Kind regards

The transparent firewall supports for connections to management only site-to-site VPN tunnels. It doesn't end of VPN connections for traffic through the ASA. You can pass through the ASA VPN traffic using a more extended access list, but it fails to complete connections not frames. Clientless SSL VPN is also not supported.

Tags: Cisco Security

Similar Questions

IPSec VPN Site-to-Site router Cisco 837 to Firewall FortiGate 200 has

I had a challege for a site to site vpn scenario that may need some brainstorming you guys.

So far, I have had a prior configuration planned for this scenario, but I'm not very sure if the tunnel I created will work because I did not test it before with this scenario. I'll go next week on this project and hopefully get a solution of brainstorming you guys. Thanks in advance!

Network diagram:

http://cjunhan.multiply.com/photos/hi-res/5/3?xurl=%2Fphotos%2Fphoto%2F5%2F3

Challenge:

(1) configure CISCO R3 IPSec Site to Site VPN between 172.20.10.0 and 10.20.20.0 using cryptographic cards

(2) IKE Phase I MainMode, lifetime 28000, md5, DH-Group1

IKE Phase II: des-esp, hmac-md5, tunnel mode

PSK: sitetositevpn

Here is my setup for review:

crypto ISAKMP policy 10

the BA

preshared authentication

Group 1

md5 hash

ISAKMP crypto key sitetositevpn address 210.x.x.66

!

Crypto ipsec transform-set esp - esp-md5-hmac ciscoset

!

infotelmap 10 ipsec-isakmp crypto map

the value of 210.x.x.66 peer

Set transform-set ciscoset

match address 111

!

!

interface Ethernet0

3 LAN description

IP 10.20.20.1 255.255.255.0

IP nat inside

servers-exit of service-policy policy

Hold-queue 100 on

!

ATM0 interface

no ip address

ATM vc-per-vp 64

No atm ilmi-keepalive

DSL-automatic operation mode

!

point-to-point interface ATM0.1

IP address 210.x.20.x.255.255.252

no ip redirection<-- disable="">

no ip unreachable<-- disable="" icmp="" host="" unreachable="">

no ip proxy-arp<-- disables="" ip="" directed="">

NAT outside IP

PVC 8/35

aal5snap encapsulation

!

!

IP nat inside source list 102 interface ATM0.1 overload

IP classless

IP route 0.0.0.0 0.0.0.0 ATM0.1

IP route 0.0.0.0 0.x.0.x.190.60.66

no ip http secure server

!

Note access-list 102 NAT traffic

access-list 102 permit ip 10.20.20.0 0.0.0.255 any

!

access-list 111 note VPN Site-to-Site 3 LAN to LAN 2 network

access-list 111 allow 0.0.0.x.x.10.0 ip 10.20.20.0 0.0.0.255

Kind regards

Junhan

Hello

Three changes required in this configuration.

(1) change the NAT-list access 102 as below:

access-list 102 deny ip 10.20.20.0 0.0.0.255 172.20.10.0 0.0.0.255

access-list 102 permit ip 10.20.20.0 0.0.0.255 any

(2) place the card encryption on interface point-to-point ATM.

(3) remote all of a default route.

Thank you

Mustafa

IPsec VPN site to site between router problem Cisco ASA. Help, please

Hello community,

I'm stuck in configuring VPN site to site between ASA (OS 9.1) and router Cisco IOS (IOS 15, 2 - 4.M4)

Attachment is router configuration and ASA. I also include the router debug output.

It seems that the two parties must isakmp missmatch configuration, but I have already disabled the KeepAlive parameters. I also turn off PFS setting on both sides. But it does not work. I have no idea on this problem.

Please help me. Any help appreciated.

Thank you

I didn't look any further, but this may be a reason:
```
 crypto map mymap 1 ipsec-isakmp dynamic dyn1 
```
The dynamic CM must always be the last sequence in a card encryption:
```
 no crypto map mymap 1 ipsec-isakmp dynamic dyn1 crypto map mymap 65000 ipsec-isakmp dynamic dyn1
```
Try this first, then we can look further.

Microsoft l2tp IPSec VPN site to site ASA on top

I have a specialized applications casino that requires end-to-end encryption. I'm under the stack of Microsoft IPSec l2tp between my XP machine and my Windows 2003 server on the LAN. Can I use the same type of protocol stack Microsoft l2tp IPSec between my XP machine and the Windows Server 2003 a branch on the SAA to site to site ASA VPN tunnel? The VPN site-to site ASA is a type of key Preshare IPSec VPN tunnelle traffic between our head office and a branch in distance.

In other words, the ASA site-to-site IPSec VPN will allow Microsoft l2tp through IPSec encrypted traffic? My ACL tunnel would allow full IP access between site. Something like:

name 192.168.100.0 TexasSubnet

name 192.168.200.0 RenoSubnet

IP TexasSubnet 255.255.255.0 RenoSubnet 255.255.255.0 allow Access-list extended nat_zero

Hello

Yes, the L2TP can be encapsulated in IPSEC as all other traffic.

However, make sure that no NAT is performed on each end. L2TP is a default header protection which will see NAT as a falsification of package and reject it.

See you soon,.

Daniel

Force start negotiating IPsec VPN Sit-to-site

Hello

I have attached two TXT files with the configurations of the two cisco 837 routers.

The problem is that the ROUTER2 has dynamic IP, and to establish the tunnel must do a ping from the ethernet interface 0 ROUTER1.

You can select the connection?

Try it without source ethernet loop back 0 instead.

Make the remote web server accessible via VPN Site to website

We have two test sites that are connected by a tunnel IPSEC VPN site-to-site (hosted on a SAA each site) over the Internet. We are trying to set up an environment to test two web applications running side by side. Two web servers are running on the Site of Test 1. We don't have the same public IP available at each site.

To address the public site 1 unique IP address restriction, we try to install ACL and NAT rules to have 2 Site accept traffic from the internet and send it on the site to the other tunnel. So 1 Web server would accept the ASA 1 internet traffic and Web Server 2 accept traffic from ASA 2 to the other site. Here's a network diagram:

We have difficulties to get this configuration works correctly. Please note that the network 192.168.3.0/24 clients are able to access the servers Web1 and Web2. This question seems to be due to our NAT configuration. This is the type of error, we see on the two firewalls:

Asymmetrical NAT rules matched for flows forward and backward; Connection for tcp src outside:4.4.4.4/443 dst outside:192.168.1.10/443 refused due to path failure reverse that of NAT

Our situation seems similar to this post: https://supportforums.cisco.com/thread/2242230

Any help would be appreciated.

Hello

What Karsten said above is true. While it is possible and works, it also means that the configuration is a little more complex to manage. I have done no such features in a real-life network environment and have always used additional public IP addresses on the local site when a server is hosted.

If you want to continue to move forward with this so here's a few points to consider and the configurations that you need.

First off it seems to me that the other server will be organized by the local Site 1 so a simple static PAT (Port Forward) must manage the Site 1.

network of the WEB-HTTP object

host 192.168.1.10

NAT (inside, outside) interface static tcp 443 443 service

And if you need TCP/80 also then you will need

network of the HTTPS WEB object

host 192.168.1.10

NAT (inside, outside) interface static service tcp 80 80

Now, 2 Site will naturally a little different that the server is hosted on the Site 1 and Site 2 is the public IP address used to publish the server on the external network.

Essentially, you will need to configure NAT that both makes dynamic PAT for the addresses of the source of the connection to your server Web 2, but also makes the static PAT (Port Forward) for the IP address of the Web Server 2. Additionally, you have to set the area of encryption on the Site 1 and Site 2 to match this new addition to the L2L VPN connection.

Unless of course you use an existing IP address on the field of encryption in the dynamic translation of PAT for the source address. In this case, it would take no change VPN L2L. I'll use that in the example below.

The NAT configuration might look like this

service object WWW

destination eq 80 tcp service

service object HTTPS

destination eq 443 tcp service

the object SOURCE-PAT-IP network

host 192.168.3.254

network of the WEB-SERVER-2-SITE1 object

host 192.168.1.11

NAT (outside, outside) 1 dynamic source no matter what static SOURCE-PAT-IP destination interface WEB-SERVER-2-SITE1 service WWW WWW

NAT (outdoors, outdoor), 2 dynamic source no matter what static SOURCE-PAT-IP destination interface WEB-SERVER-2-SITE1 service HTTPS HTTPS

So, essentially, NAT configurations above should ake 'all' traffic coming from behind 'outside' interface intended to "outside" "interface" IP address and translate the source to ' SOURCE-PAT-IP ' address and untranslate destination to "WEB-SERVER-2-SITE1".

Make sure that the IP address chosen (in this case 192.168.3.254) is not used on any device. If she is then replace it with something that is not currently used in the network. Otherwise, configure an IP address of some other subnet and include in the L2L VPN configurations on both sites.

Unless you already have it, you also have this configuration command to activate the traffic to make a U-turn/pin on the ' outside ' of the Site 2 ASA interface

permit same-security-traffic intra-interface

Hope this helps

Remember to mark a reply as the answer if it answered your question.

Feel free to ask more if necessary.

-Jouni

ASA 9.2 IPSEC VPN

I have ASA version 9.2 (2) 4 - model 5515

I need to configure IPSEC VPN site-to-site.

Can anyone share with me the example of ASA 9.2 CLI for IPSEC VPN configuration?

Congratulations to find a solution to your problem. Thank you for posting on the Board to indicate that the issue is resolved and to share the solution. This can help other readers in the forum.

HTH

Rick

L2l IPSec VPN blocks SQL (ASA v8.4)

Good evening everyone,

I have an ASA 5510 8.4 (2) which has an IPSec VPN site to a 3rd party who run a form any checkpoint running. VPN establishes and allows to access a server in our demilitarized zone on all the ports that we tested (so far HTTP, FTP, SSL, RDP), with the exception of SQL that does not even reach the server. I've got Wireshark running on the DMZ server and if the 3rd party initiates a conversation of TCP of their server on any of the ports on the server I see all desired packages come with the correct IPs ETC (without NAT takes place through the VPN), but when an ODBC client attempts to query the SQL Server on our DMZ zone packets do not reach the level of the server. What I see is the number of bytes of RX on the VPN increases whenever the query is run, but certainly not arriving on the SQL Server.

Also if I come back to the ASA to the old PIX, it replaced with the same VPN configuration but on version 7.x, then it works fine.

While I find some time to clean up the config this weekend, I have ideas.

Thank you very much

Simon.

Hi Simon,.

If you look at the options sys in the ASDM he advises that you still need ACL for traffic. As I understand it, in the old days, when you were in as you pointed out. If you set the ports in this group then Yes, it's a whole and potentially your only protection is the NAT or his absence.

I would like to add an another ACE to the external interface, which allows the source to you DMZ host (see below)

Object-group service GROUP SQL-tcp PORTS

EQ port 1433 object

EQ object Port 1434

Port-object eq 1521

outside_access extended access list permit tcp host 192.168.100.30 DMZ_158-group of objects SQL-PORTS object

Concerning

site-to-site ipsec VPN

Hey all, I was instructed to set up a tunnel vpn site-to-site between 2 offices. I think I have everything configured correctly for the most part, but when I generate a valuable traffic, tunnel does. Can you tell me to look at the debug output below what could be the problem? Aaa.aaa.aaa.aaa my IP address and the IP address of my counterpart is bbb.bbb.bbb.bbb

ROUTER #.

* 27 Feb 14:41:30.677: IPSEC (sa_request):,.

(Eng. msg key.) Local OUTGOING = aaa.aaa.aaa.aaa:500, distance = bbb.bbb.bbb.bbb:500,

local_proxy = 172.18.230.0/255.255.255.0/0/0 (type = 4),

remote_proxy = 192.168.230.0/255.255.255.0/0/0 (type = 4),

Protocol = ESP, transform = esp - aes esp-sha-hmac (Tunnel),

lifedur = Ko 86400 s and 4608000,

SPI = 0 x 0 (0), id_conn = 0, keysize = 128, flags = 0 x 0

* 14:41:30.677 Feb 27: ISAKMP: 500 local port, remote port 500

* 14:41:30.677 Feb 27: ISAKMP: set new node 0 to QM_IDLE

* 14:41:30.677 Feb 27: ISAKMP: (0): insert his with his 4BA8CE24 = success

* 14:41:30.677 Feb 27: ISAKMP: (0): cannot start aggressive mode, try the main mode.

* 14:41:30.677 Feb 27: ISAKMP: (0): pair found pre-shared key matching bbb.bbb.bbb.bbb

* 27 Feb 14:41:30.677: ISAKMP: (0): built of NAT - T of the seller-rfc3947 ID

* 27 Feb 14:41:30.677: ISAKMP: (0): built the seller-07 ID NAT - t

* 27 Feb 14:41:30.677: ISAKMP: (0): built of NAT - T of the seller-03 ID

* 27 Feb 14:41:30.677: ISAKMP: (0): built the seller-02 ID NAT - t

* 14:41:30.677 Feb 27: ISAKMP: (0): entry = IKE_MESG_FROM_IPSEC, IKE_SA_REQ_MM

* 14:41:30.677 Feb 27: ISAKMP: (0): former State = new State IKE_READY = IKE_I_MM1

* 27 Feb 14:41:30.677: ISAKMP: (0): Beginner Main Mode Exchange

* 27 Feb 14:41:30.677: ISAKMP: (0): package bbb.bbb.bbb.bbb my_port 500 peer_port 500 (I) sending MM_NO_STATE

* 14:41:30.677 Feb 27: ISAKMP: (0): sending a packet IPv4 IKE.

* 14:41:30.713 Feb 27: ISAKMP (0): packet received dport 500 sport Global 500 (I) MM_NO_STATE bbb.bbb.bbb.bbb

* 14:41:30.713 Feb 27: ISAKMP: (0): entry = IKE_MESG_FROM_PEER, IKE_MM_EXCH

* 14:41:30.713 Feb 27: ISAKMP: (0): former State = new State IKE_I_MM1 = IKE_I_MM2

* 27 Feb 14:41:30.713: ISAKMP: (0): treatment ITS payload. Message ID = 0

* 27 Feb 14:41:30.713: ISAKMP: (0): load useful vendor id of treatment

* 27 Feb 14:41:30.713: ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 123

* 27 Feb 14:41:30.713: ISAKMP: (0): provider ID is NAT - T v2

* 27 Feb 14:41:30.713: ISAKMP: (0): load useful vendor id of treatment

* 27 Feb 14:41:30.713: ISAKMP: (0): IKE frag vendor processing id payload

* 14:41:30.717 Feb 27: ISAKMP: (0): IKE Fragmentation support not enabled

* 14:41:30.717 Feb 27: ISAKMP: (0): pair found pre-shared key matching bbb.bbb.bbb.bbb

* 27 Feb 14:41:30.717: ISAKMP: (0): pre-shared key local found

* 27 Feb 14:41:30.717: ISAKMP: (0): pre-shared xauth authentication

* 14:41:30.717 Feb 27: ISAKMP: (0): audit ISAKMP transform 3 against the policy of priority 10

* 14:41:30.717 Feb 27: ISAKMP: 3DES-CBC encryption

* 14:41:30.717 Feb 27: ISAKMP: SHA hash

* 14:41:30.717 Feb 27: ISAKMP: group by default 2

* 14:41:30.717 Feb 27: ISAKMP: pre-shared key auth

* 14:41:30.717 Feb 27: ISAKMP: type of life in seconds

* 14:41:30.717 Feb 27: ISAKMP: life (IPV) 0 x 0 0 x 1 0 x 51 0x80

* 14:41:30.717 Feb 27: ISAKMP: (0): offered hash algorithm does not match policy.

* 14:41:30.717 Feb 27: ISAKMP: (0): atts are not acceptable. Next payload is 0

* 14:41:30.717 Feb 27: ISAKMP: (0): audit ISAKMP transform 3 against the policy of priority 15

* 14:41:30.717 Feb 27: ISAKMP: 3DES-CBC encryption

* 14:41:30.717 Feb 27: ISAKMP: SHA hash

* 14:41:30.717 Feb 27: ISAKMP: group by default 2

* 14:41:30.717 Feb 27: ISAKMP: pre-shared key auth

* 14:41:30.717 Feb 27: ISAKMP: type of life in seconds

* 14:41:30.717 Feb 27: ISAKMP: life (IPV) 0 x 0 0 x 1 0 x 51 0x80

* 14:41:30.717 Feb 27: ISAKMP: (0): free encryption algorithm does not match policy.

* 14:41:30.717 Feb 27: ISAKMP: (0): atts are not acceptable. Next payload is 0

* 14:41:30.717 Feb 27: ISAKMP: (0): audit ISAKMP transform 3 against priority policy 20

* 14:41:30.717 Feb 27: ISAKMP: 3DES-CBC encryption

* 14:41:30.717 Feb 27: ISAKMP: SHA hash

* 14:41:30.717 Feb 27: ISAKMP: group by default 2

* 14:41:30.717 Feb 27: ISAKMP: pre-shared key auth

* 14:41:30.717 Feb 27: ISAKMP: type of life in seconds

* 14:41:30.717 Feb 27: ISAKMP: life (IPV) 0 x 0 0 x 1 0 x 51 0x80

* 14:41:30.717 Feb 27: ISAKMP: (0): atts are acceptable. Next payload is 0

* 14:41:30.717 Feb 27: ISAKMP: (0): Acceptable atts: real life: 0

* 14:41:30.717 Feb 27: ISAKMP: (0): Acceptable atts:life: 0

* 14:41:30.717 Feb 27: ISAKMP: (0): fill atts in his vpi_length:4

* 14:41:30.717 Feb 27: ISAKMP: (0): fill atts in his life_in_seconds:86400

* 14:41:30.717 Feb 27: ISAKMP: (0): return real life: 86400

* 14:41:30.717 Feb 27: ISAKMP: (0): timer life Started: 86400.

* 27 Feb 14:41:30.717: ISAKMP: (0): load useful vendor id of treatment

* 27 Feb 14:41:30.717: ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 123

* 27 Feb 14:41:30.717: ISAKMP: (0): provider ID is NAT - T v2

* 27 Feb 14:41:30.717: ISAKMP: (0): load useful vendor id of treatment

* 27 Feb 14:41:30.717: ISAKMP: (0): IKE frag vendor processing id payload

* 14:41:30.717 Feb 27: ISAKMP: (0): IKE Fragmentation support not enabled

* 14:41:30.717 Feb 27: ISAKMP: (0): entry = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE

* 14:41:30.717 Feb 27: ISAKMP: (0): former State = new State IKE_I_MM2 = IKE_I_MM2

* 27 Feb 14:41:30.717: ISAKMP: (0): package bbb.bbb.bbb.bbb my_port 500 peer_port 500 (I) sending MM_SA_SETUP

* 14:41:30.717 Feb 27: ISAKMP: (0): sending a packet IPv4 IKE.

* 14:41:30.721 Feb 27: ISAKMP: (0): entry = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE

* 14:41:30.721 Feb 27: ISAKMP: (0): former State = new State IKE_I_MM2 = IKE_I_MM3

* 14:41:30.753 Feb 27: ISAKMP (0): packet received dport 500 sport Global 500 (I) MM_SA_SETUP bbb.bbb.bbb.bbb

* 14:41:30.753 Feb 27: ISAKMP: (0): entry = IKE_MESG_FROM_PEER, IKE_MM_EXCH

* 14:41:30.753 Feb 27: ISAKMP: (0): former State = new State IKE_I_MM3 = IKE_I_MM4

* 27 Feb 14:41:30.757: ISAKMP: (0): processing KE payload. Message ID = 0

* 27 Feb 14:41:30.789: ISAKMP: (0): processing NONCE payload. Message ID = 0

* 14:41:30.789 Feb 27: ISAKMP: (0): pair found pre-shared key matching bbb.bbb.bbb.bbb

* 27 Feb 14:41:30.789: ISAKMP: (1640): load useful vendor id of treatment

* 27 Feb 14:41:30.789: ISAKMP: (1640): provider ID is the unit

* 27 Feb 14:41:30.789: ISAKMP: (1640): load useful vendor id of treatment

* 27 Feb 14:41:30.789: ISAKMP: (1640): provider ID seems the unit/DPD but major incompatibility of 193

* 27 Feb 14:41:30.789: ISAKMP: (1640): provider ID is XAUTH

* 27 Feb 14:41:30.789: ISAKMP: (1640): load useful vendor id of treatment

* 27 Feb 14:41:30.789: ISAKMP: (1640): addressing another box of IOS!

* 27 Feb 14:41:30.789: ISAKMP: (1640): load useful vendor id of treatment

* 14:41:30.789 Feb 27: ISAKMP: (1640): vendor ID seems the unit/DPD but hash mismatch

* 14:41:30.789 Feb 27: ISAKMP: receives the payload type 20

* 14:41:30.789 Feb 27: ISAKMP (1640): sound not hash no match - this node outside NAT

* 14:41:30.789 Feb 27: ISAKMP: receives the payload type 20

* 14:41:30.789 Feb 27: ISAKMP (1640): No. NAT found for oneself or peer

* 14:41:30.789 Feb 27: ISAKMP: (1640): entry = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE

* 14:41:30.789 Feb 27: ISAKMP: (1640): former State = new State IKE_I_MM4 = IKE_I_MM4

* 14:41:30.789 Feb 27: ISAKMP: (1640): send initial contact

* 14:41:30.789 Feb 27: ISAKMP: (1640): ITS been pre-shared key, using id ID_IPV4_ADDR type authentication

* 14:41:30.789 Feb 27: ISAKMP (1640): payload ID

next payload: 8

type: 1

address: aaa.aaa.aaa.aaa

Protocol: 17

Port: 500

Length: 12

* 14:41:30.789 Feb 27: ISAKMP: (1640): the total payload length: 12

* 27 Feb 14:41:30.789: ISAKMP: (1640): package bbb.bbb.bbb.bbb my_port 500 peer_port 500 (I) sending MM_KEY_EXCH

* 14:41:30.789 Feb 27: ISAKMP: (1640): an IPv4 IKE packet is sent.

* 14:41:30.793 Feb 27: ISAKMP: (1640): entry = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE

* 14:41:30.793 Feb 27: ISAKMP: (1640): former State = new State IKE_I_MM4 = IKE_I_MM5

* 14:41:30.825 Feb 27: ISAKMP (1640): packet received dport 500 sport Global 500 (I) MM_KEY_EXCH bbb.bbb.bbb.bbb

* 14:41:30.825 27 Feb: % CRYPTO-6-IKMP_NOT_ENCRYPTED: IKE bbb.bbb.bbb.bbb package was not encrypted and it should have been.

* 14:41:30.825 Feb 27: ISAKMP (1640): increment the count of errors on his, try 1 of 5: reset_retransmission

* 27 Feb 14:41:31.825: ISAKMP: (1640): transmit phase 1 MM_KEY_EXCH...

* 14:41:31.825 Feb 27: ISAKMP (1640): increment the count of errors on his, try 2 of 5: retransmit the phase 1

* 27 Feb 14:41:31.825: ISAKMP: (1640): transmit phase 1 MM_KEY_EXCH

* 27 Feb 14:41:31.825: ISAKMP: (1640): package bbb.bbb.bbb.bbb my_port 500 peer_port 500 (I) sending MM_KEY_EXCH

* 14:41:31.825 Feb 27: ISAKMP: (1640): an IPv4 IKE packet is sent.

* 14:41:31.857 Feb 27: ISAKMP (1640): packet received dport 500 sport Global 500 (I) MM_KEY_EXCH bbb.bbb.bbb.bbb

* 14:41:31.857 27 Feb: % CRYPTO-6-IKMP_NOT_ENCRYPTED: IKE bbb.bbb.bbb.bbb package was not encrypted and it should have been.

* 14:41:31.857 Feb 27: ISAKMP (1640): increment the count of errors on his, try 3 of 5: reset_retransmission

* 27 Feb 14:41:32.857: ISAKMP: (1640): transmit phase 1 MM_KEY_EXCH...

* 14:41:32.857 Feb 27: ISAKMP (1640): increment the count of errors on his, try 4 out 5: retransmit the phase 1

* 27 Feb 14:41:32.857: ISAKMP: (1640): transmit phase 1 MM_KEY_EXCH

* 27 Feb 14:41:32.857: ISAKMP: (1640): package bbb.bbb.bbb.bbb my_port 500 peer_port 500 (I) sending MM_KEY_EXCH

* 14:41:32.857 Feb 27: ISAKMP: (1640): an IPv4 IKE packet is sent.

* 14:41:32.889 Feb 27: ISAKMP (1640): packet received dport 500 sport Global 500 (I) MM_KEY_EXCH bbb.bbb.bbb.bbb

* 27 Feb 14:41:32.889: ISAKMP: (1640): package of phase 1 is a duplicate of a previous package.

* 27 Feb 14:41:32.889: ISAKMP: (1640): retransmission jumped to the stage 1 (time elapsed since the last transmission of 32)

ROUTER #u all

Off crypto conditional debugging.

All possible debugging has been disabled

* 14:42:00.821 27 Feb: % CRYPTO-6-IKMP_NOT_ENCRYPTED: IKE bbb.bbb.bbb.bbb package was not encrypted and it should have been.

* 14:42:01.853 27 Feb: % CRYPTO-6-IKMP_NOT_ENCRYPTED: IKE bbb.bbb.bbb.bbb package was not encrypted and it should have been.

Thank you all

Does that help?

https://supportforums.Cisco.com/docs/doc-4059

Need help with the configuration of the Site with crossed on Cisco ASA5510 8.2 IPSec VPN Client (1)

Need urgent help in the configuration of the Client VPN IPSec Site with crossed on Cisco ASA5510 - 8.2 (1).

Here is the presentation:

There are two leased lines for Internet access - a route 1.1.1.1 and 2.2.2.2, the latter being the default Standard, old East for backup.

I was able to configure the Client VPN IPSec Site

(1) with access to the outside so that the internal network (172.16.0.0/24) behind the asa

(2) with Split tunnel with simultaneous assess internal LAN and Internet on the outside.

But I was not able to make the tradiotional model Hairpinng to work in this scenario.

I followed every possible suggestions made on this subject in many topics of Discussion but still no luck. Can someone help me here please?

Here is the race-Conf with Normal Client to Site IPSec VPN configured with no access boarding:

LIMITATION: Cannot boot into any other image ios for unavoidable reasons, must use 8.2 (1)

race-conf - Site VPN Customer normal work without internet access/split tunnel
: ASA Version 8.2 (1) ! ciscoasa hostname domain cisco.campus.com enable the encrypted password xxxxxxxxxxxxxx XXXXXXXXXXXXXX encrypted passwd names of ! interface GigabitEthernet0/0 nameif outside internet1 security-level 0 IP 1.1.1.1 255.255.255.240 ! interface GigabitEthernet0/1 nameif outside internet2 security-level 0 IP address 2.2.2.2 255.255.255.224 ! interface GigabitEthernet0/2 nameif dmz interface security-level 0 IP 10.0.1.1 255.255.255.0 ! interface GigabitEthernet0/3 nameif campus-lan security-level 0 IP 172.16.0.1 255.255.0.0 ! interface Management0/0 nameif CSC-MGMT security-level 100 the IP 10.0.0.4 address 255.255.255.0 ! boot system Disk0: / asa821 - k8.bin boot system Disk0: / asa843 - k8.bin passive FTP mode DNS server-group DefaultDNS domain cisco.campus.com permit same-security-traffic inter-interface permit same-security-traffic intra-interface object-group network cmps-lan the object-group CSC - ip network object-group network www-Interior object-group network www-outside object-group service tcp-80 object-group service udp-53 object-group service https object-group service pop3 object-group service smtp object-group service tcp80 object-group service http-s object-group service pop3-110 object-group service smtp25 object-group service udp53 object-group service ssh object-group service tcp-port port udp-object-group service object-group service ftp object-group service ftp - data object-group network csc1-ip object-group service all-tcp-udp access list INTERNET1-IN extended permit ip host 1.2.2.2 2.2.2.3 access-list extended SCC-OUT permit ip host 10.0.0.5 everything list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 any eq www list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 any https eq list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 any eq ssh list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 no matter what eq ftp list of access CAMPUS-LAN extended permitted udp 172.16.0.0 255.255.0.0 no matter what eq field list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 any eq smtp list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 any eq pop3 access CAMPUS-wide LAN ip allowed list a whole access-list CSC - acl note scan web and mail traffic access-list CSC - acl extended permit tcp any any eq smtp access-list CSC - acl extended permit tcp any any eq pop3 access-list CSC - acl note scan web and mail traffic access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq 993 access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq imap4 access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq 465

race-conf - Site VPN Customer normal work without internet access/split tunnel

ASA Version 8.2 (1)

ciscoasa hostname

domain cisco.campus.com

enable the encrypted password xxxxxxxxxxxxxx

XXXXXXXXXXXXXX encrypted passwd

names of

interface GigabitEthernet0/0

nameif outside internet1

security-level 0

IP 1.1.1.1 255.255.255.240

interface GigabitEthernet0/1

nameif outside internet2

security-level 0

IP address 2.2.2.2 255.255.255.224

interface GigabitEthernet0/2

nameif dmz interface

security-level 0

IP 10.0.1.1 255.255.255.0

interface GigabitEthernet0/3

nameif campus-lan

security-level 0

IP 172.16.0.1 255.255.0.0

interface Management0/0

nameif CSC-MGMT

security-level 100

the IP 10.0.0.4 address 255.255.255.0

boot system Disk0: / asa821 - k8.bin

boot system Disk0: / asa843 - k8.bin

passive FTP mode

DNS server-group DefaultDNS

domain cisco.campus.com

permit same-security-traffic inter-interface

permit same-security-traffic intra-interface

object-group network cmps-lan

the object-group CSC - ip network

object-group network www-Interior

object-group network www-outside

object-group service tcp-80

object-group service udp-53

object-group service https

object-group service pop3

object-group service smtp

object-group service tcp80

object-group service http-s

object-group service pop3-110

object-group service smtp25

object-group service udp53

object-group service ssh

object-group service tcp-port

port udp-object-group service

object-group service ftp

object-group service ftp - data

object-group network csc1-ip

object-group service all-tcp-udp

access list INTERNET1-IN extended permit ip host 1.2.2.2 2.2.2.3

access-list extended SCC-OUT permit ip host 10.0.0.5 everything

list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 any eq www

list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 any https eq

list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 any eq ssh

list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 no matter what eq ftp

list of access CAMPUS-LAN extended permitted udp 172.16.0.0 255.255.0.0 no matter what eq field

list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 any eq smtp

list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 any eq pop3

access CAMPUS-wide LAN ip allowed list a whole

access-list CSC - acl note scan web and mail traffic

access-list CSC - acl extended permit tcp any any eq smtp

access-list CSC - acl extended permit tcp any any eq pop3

access-list CSC - acl note scan web and mail traffic

access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq 993

access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq imap4

access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq 465

access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq www

access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq https

access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq smtp

access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq pop3

access-list extended INTERNET2-IN permit ip any host 1.1.1.2

access-list sheep extended ip 172.16.0.0 allow 255.255.0.0 172.16.0.0 255.255.0.0

access list DNS-inspect extended permit tcp any any eq field

access list DNS-inspect extended permit udp any any eq field

access-list extended capin permit ip host 172.16.1.234 all

access-list extended capin permit ip host 172.16.1.52 all

access-list extended capin permit ip any host 172.16.1.52

Capin list extended access permit ip host 172.16.0.82 172.16.0.61

Capin list extended access permit ip host 172.16.0.61 172.16.0.82

access-list extended capout permit ip host 2.2.2.2 everything

access-list extended capout permit ip any host 2.2.2.2

Access campus-lan_nat0_outbound extended ip 172.16.0.0 list allow 255.255.0.0 192.168.150.0 255.255.255.0

pager lines 24

Enable logging

debug logging in buffered memory

asdm of logging of information

Internet1-outside of MTU 1500

Internet2-outside of MTU 1500

interface-dmz MTU 1500

Campus-lan of MTU 1500

MTU 1500 CSC-MGMT

IP local pool 192.168.150.2 - 192.168.150.250 mask 255.255.255.0 vpnpool1

IP check path reverse interface internet2-outside

IP check path reverse interface interface-dmz

IP check path opposite campus-lan interface

IP check path reverse interface CSC-MGMT

no failover

ICMP unreachable rate-limit 1 burst-size 1

ASDM image disk0: / asdm - 621.bin

don't allow no asdm history

ARP timeout 14400

interface of global (internet1-outside) 1

interface of global (internet2-outside) 1

NAT (campus-lan) 0-campus-lan_nat0_outbound access list

NAT (campus-lan) 1 0.0.0.0 0.0.0.0

NAT (CSC-MGMT) 1 10.0.0.5 255.255.255.255

static (CSC-MGMT, internet2-outside) 2.2.2.3 10.0.0.5 netmask 255.255.255.255

Access-group INTERNET2-IN interface internet1-outside

group-access INTERNET1-IN interface internet2-outside

group-access CAMPUS-LAN in campus-lan interface

CSC-OUT access-group in SCC-MGMT interface

Internet2-outside route 0.0.0.0 0.0.0.0 2.2.2.5 1

Route internet1-outside 0.0.0.0 0.0.0.0 1.1.1.5 2

Timeout xlate 03:00

Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

timeout tcp-proxy-reassembly 0:01:00

dynamic-access-policy-registration DfltAccessPolicy

the ssh LOCAL console AAA authentication

AAA authentication enable LOCAL console

Enable http server

http 10.0.0.2 255.255.255.255 CSC-MGMT

http 10.0.0.8 255.255.255.255 CSC-MGMT

HTTP 1.2.2.2 255.255.255.255 internet2-outside

HTTP 1.2.2.2 255.255.255.255 internet1-outside

No snmp server location

No snmp Server contact

Server enable SNMP traps snmp authentication linkup, linkdown cold start

Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

life crypto ipsec security association seconds 28800

Crypto ipsec kilobytes of life - safety 4608000 association

crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs set group5

Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

Crypto map internet2-outside_map 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

crypto internet2-outside_map outside internet2 network interface card

Crypto ca trustpoint _SmartCallHome_ServerCA

Configure CRL

Crypto ca certificate chain _SmartCallHome_ServerCA

certificate ca xyzxyzxyzyxzxyzxyzxyzxxyzyxzyxzy

a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as

a67a897as a67a897as a67a897as a67a897as a67a897as

quit smoking

ISAKMP crypto enable internet2-outside

crypto ISAKMP policy 10

preshared authentication

aes encryption

md5 hash

Group 2

life 86400

Telnet 10.0.0.2 255.255.255.255 CSC-MGMT

Telnet 10.0.0.8 255.255.255.255 CSC-MGMT

Telnet timeout 5

SSH 1.2.3.3 255.255.255.240 internet1-outside

SSH 1.2.2.2 255.255.255.255 internet1-outside

SSH 1.2.2.2 255.255.255.255 internet2-outside

SSH timeout 5

Console timeout 0

a basic threat threat detection

Statistics-list of access threat detection

no statistical threat detection tcp-interception

WebVPN

internal VPN_TG_1 group policy

VPN_TG_1 group policy attributes

Protocol-tunnel-VPN IPSec

username ssochelpdesk encrypted password privilege 15 xxxxxxxxxxxxxx

privilege of encrypted password username administrator 15 xxxxxxxxxxxxxx

username vpnuser1 encrypted password privilege 0 xxxxxxxxxxxxxx

username vpnuser1 attributes

VPN-group-policy VPN_TG_1

type tunnel-group VPN_TG_1 remote access

attributes global-tunnel-group VPN_TG_1

address vpnpool1 pool

Group Policy - by default-VPN_TG_1

IPSec-attributes tunnel-group VPN_TG_1

pre-shared-key *.

class-map cmap-DNS

matches the access list DNS-inspect

CCS-class class-map

corresponds to the CSC - acl access list

type of policy-card inspect dns preset_dns_map

parameters

message-length maximum 512

Policy-map global_policy

CCS category

CSC help

cmap-DNS class

inspect the preset_dns_map dns

global service-policy global_policy

context of prompt hostname

Cryptochecksum: y0y0y0y0y0y0y0y0y0y0y0y0y0y

: end

Adding dynamic NAT for 192.168.150.0/24 on the external interface works, or works the sysopt connection permit VPN

Please tell what to do here, to pin all of the traffic Internet from VPN Clients.

That is, that I need clients connected via VPN tunnel, when connected to the internet, should have their addresses IP NAT'ted against the address of outside internet2 network 2.2.2.2 interface, as it happens for the customers of Campus (172.16.0.0/16)

I am well aware of all involved in here, so please be elaborative in your answers. Please let me know if you need more information about this configuration to respond to my request.

Thank you & best regards

MAXS

Hello

If possible, I'd like to see that a TCP connection attempt (e.g. http://www.google.com) in the ASDM logging of the VPN Client when you set up the dynamic NAT for the VPN Pool also.

I'll try also the command "packet - trace" on the SAA, while the VPN Client is connected to the ASA.

The command format is

packet-tracer intput tcp

That should tell what the SAA for this kind of package entering its "input" interface

Still can not see something wrong with the configuration (other than the statement of "nat" missing Dynamics PAT)

-Jouni

Easy VPN with IPSec VPN L2L (Site - to - Site) in the same ASA 5505

Hi Experts,

We have an ASA 5505 in our environment, and currently two IPSec VPN L2L tunnels are established. But we intend to connect with VPN (Network Extension Mode) easy to another site as a customer. Is it possible to configure easy VPN configurations by keeping the currently active IPSec L2L VPN(Site-to-Site) tunnels? If not possible is there any work around?

Here's the warning we get then tried to configure the easy VPN Client.

NOCMEFW1 (config) # vpnclient enable

* Delete "nat (inside) 0 S2S - VPN"

* Detach crypto card attached to the outside interface

* Remove the tunnel groups defined by the user

* Remove the manual configuration of ISA policies

CONFLICT of CONFIG: Configuration that would prevent the Cisco Easy VPN Remo success

you

operation was detected and listed above. Please solve the

above a configuration and re - activate.

Thanks and greetings

ANUP sisi

"Dynamic crypto map must be installed on the server device.

Yes, dynamic crypto is configured on the EasyVPN server.

Thank you

ISA500 site by site ipsec VPN with Cisco IGR

Hello

I tried a VPN site by site work with Openswan and Cisco 2821 router configuration an Ipsec tunnel to site by site with Cisco 2821 and ISA550.

But without success.

my config for openswan, just FYI, maybe not importand for this problem

installation of config

protostack = netkey

nat_traversal = yes

virtual_private=%v4:10.0.0.0/8,%v4:192.168.0.0/16,%v4:172.16.0.0/12,%4:!$RIGHT_SUBNET

nhelpers = 0

Conn rz1

IKEv2 = no

type = tunnel

left = % all

leftsubnet=192.168.5.0/24

right =.

rightsourceip = 192.168.1.2

rightsubnet=192.168.1.0/24

Keylife 28800 = s

ikelifetime 28800 = s

keyingtries = 3

AUTH = esp

ESP = aes128-sha1

KeyExchange = ike

authby secret =

start = auto

IKE = aes128-sha1; modp1536

dpdaction = redΘmarrer

dpddelay = 30

dpdtimeout = 60

PFS = No.

aggrmode = no

Config Cisco 2821 for dynamic dialin:

crypto ISAKMP policy 1

BA aes

sha hash

preshared authentication

Group 5

lifetime 28800

!

card crypto CMAP_1 1-isakmp dynamic ipsec DYNMAP_1

!

access-list 102 permit ip 192.168.1.0 0.0.0.255 192.168.5.0 0.0.0.255

!

Crypto ipsec transform-set ESP-AES-SHA1 esp - aes esp-sha-hmac

crypto dynamic-map DYNMAP_1 1

game of transformation-ESP-AES-SHA1

match address 102

!

ISAKMP crypto key address 0.0.0.0 0.0.0.0

ISAKMP crypto keepalive 30 periodicals

!

life crypto ipsec security association seconds 28800

!

interface GigabitEthernet0/0.4002

card crypto CMAP_1

!

I tried ISA550 a config with the same constelations, but without suggesting.

Anyone has the same problem?

And had anyone has a tip for me, or has someone expirense with a site-by-site with ISA550 and Cisco 2821 ipsec tunnel?

I can successfully establish a tunnel between openswan linux server and the isa550.

Patrick,

as you can see on newspapers, the software behind ISA is also OpenSWAN

I have a facility with a 892 SRI running which should be the same as your 29erxx.

Use your IOS Config dynmap, penny, you are on the average nomad. If you don't have any RW customer you shoul go on IOS "No.-xauth" after the isakmp encryption key.

Here is my setup, with roardwarrior AND 2, site 2 site.

session of crypto consignment

logging crypto ezvpn

!

crypto ISAKMP policy 1

BA 3des

preshared authentication

Group 2

lifetime 28800

!

crypto ISAKMP policy 2

BA 3des

md5 hash

preshared authentication

Group 2

lifetime 28800

!

crypto ISAKMP policy 3

BA 3des

preshared authentication

Group 2

!

crypto ISAKMP policy 4

BA 3des

md5 hash

preshared authentication

Group 2

!

crypto ISAKMP policy 5

BA 3des

preshared authentication

Group 2

life 7200

ISAKMP crypto address XXXX XXXXX No.-xauth key

XXXX XXXX No.-xauth address isakmp encryption key

!

ISAKMP crypto client configuration group by default

key XXXX

DNS XXXX

default pool

ACL easyvpn_client_routes

PFS

!

!

Crypto ipsec transform-set esp-3des esp-sha-hmac FEAT

!

dynamic-map crypto VPN 20

game of transformation-FEAT

market arriere-route

!

!

card crypto client VPN authentication list by default

card crypto VPN isakmp authorization list by default

crypto map VPN client configuration address respond

10 VPN ipsec-isakmp crypto map

Description of VPN - 1

defined peer XXX

game of transformation-FEAT

match the address internal_networks_ipsec

11 VPN ipsec-isakmp crypto map

VPN-2 description

defined peer XXX

game of transformation-FEAT

PFS group2 Set

match the address internal_networks_ipsec2

card crypto 20-isakmp dynamic VPN ipsec VPN

!

!

Michael

Please note all useful posts

Router 886VA Site to site ipsec vpn fqdn

Hello

I would like to create a vpn site-to site with a crypto fqdn on the side of the branch.

The reason is in our head office in the wan IP will be hungry for change, and I want the branch office router to reconnect as soon as they get the new ip address.

How could a which?

Here is my Config:

 ip domain lookup source-interface Dialer0 crypto isakmp policy 10 encr aes authentication pre-share group 2 lifetime 14400 crypto isakmp key MyKey address 22.22.22.22 crypto ipsec transform-set MySET esp-3des esp-md5-hmac crypto map BranchMap 10 ipsec-isakmp description HDG set peer 22.22.22.22 set transform-set MySET match address 110 int Dialer 0 ip access-group 101 in cryptop map BranchMap access-list 101 remark INT DIALER0 INCOMING access-list 101 permit udp host 62.2.24.162 eq domain host 11.11.11.11 access-list 101 permit udp host 62.2.17.60 eq domain host 11.11.11.11 access-list 101 permit udp host 22.22.22.22 host 11.11.11.11 eq non500-isakmp access-list 101 permit udp host 22.22.22.22 host 11.11.11.11 eq isakmp access-list 101 permit esp host 22.22.22.22 host 11.11.11.11 access-list 101 permit ahp host 22.22.22.22 host 11.11.11.11 access-list 101 permit tcp any any established access-list 101 permit udp host 129.132.2.21 eq ntp host 11.11.11.11 eq ntp access-list 101 permit udp host 130.60.75.52 eq ntp host 11.11.11.11 eq ntp access-list 101 permit udp host 8.8.8.8 eq domain host 11.11.11.11 access-list 101 remark INT DIALER0 INCOMING

11.11.11.11 = > local WAN IP Branch

22.22.22.22-online distance seat WAN IP

Thank you

If your HQ has a (rare) dynamic IP address, you must do 3 things:

1. set up a dynamic DNS host name for your HQ VPN peer (dyndns.org, etc..)

2. your counterpart dynamic crypto map using "dynamic peer hqddns.company.com defined".

3. your isakmp for the peer key a wildcard character ("crypto isakmp key addr 0.0.0.0")

If you say that it is an IP change single opposite HQ, then maybe:

1 Add the new IP address to your 'access-list 101' ACL (remember to use a name instead of ACL numbered for readability)

2. Add another encryption with the new IP address isakmp key

3. Add the new IP address as secondary peer:

map BranchMap 10 ipsec-isakmp crypto
the default peer 22.22.22.22
defined peer 3.3.3.3

Establish a IPsec VPN connection, but remote site can't ping main office

Hi, I set up connection from site to site IPsec VPN between cisco 892 (main site) router and linksys router wrv210 (remote site). My problem is that I can ping network router wrv210 lan of my main office where is cisco 892 router, but I cannot ping the main site of linksys wrv210 lan (my remote site).

My configuration on the cisco 892 router:

type of class-card inspect correspondence sdm-cls-VPNOutsideToInside-1

game group-access 103

type of class-card inspect correspondence sdm-cls-VPNOutsideToInside-3

game group-access 106

type of class-card inspect correspondence sdm-cls-VPNOutsideToInside-2

game group-access 105

type of class-card inspect correspondence sdm-cls-VPNOutsideToInside-5

game group-access 108

type of class-card inspect correspondence sdm-cls-VPNOutsideToInside-4

game group-access 107

type of class-card inspect correspondence sdm-cls-VPNOutsideToInside-7

group-access 110 match

type of class-card inspect correspondence sdm-cls-VPNOutsideToInside-6

game group-access 109

type of class-card inspect correspondence sdm-cls-VPNOutsideToInside-9

game group-access 112

type of class-card inspect correspondence sdm-cls-VPNOutsideToInside-8

game group-access 111

type of class-card inspect entire game SDM_AH

match the name of group-access SDM_AH

type of class-card inspect entire game SDM_ESP

match the name of group-access SDM_ESP

type of class-card inspect entire game SDM_VPN_TRAFFIC

match Protocol isakmp

match Protocol ipsec-msft

corresponds to the SDM_AH class-map

corresponds to the SDM_ESP class-map

type of class-card inspect the correspondence SDM_VPN_PT

game group-access 102

corresponds to the SDM_VPN_TRAFFIC class-map

type of class-card inspect entire game PAC-cls-insp-traffic

match Protocol cuseeme

dns protocol game

ftp protocol game

h323 Protocol game

https protocol game

match icmp Protocol

match the imap Protocol

pop3 Protocol game

netshow Protocol game

Protocol shell game

match Protocol realmedia

match rtsp Protocol

smtp Protocol game

sql-net Protocol game

streamworks Protocol game

tftp Protocol game

vdolive Protocol game

tcp protocol match

udp Protocol game

inspect the class-map match PAC-insp-traffic type

corresponds to the class-map PAC-cls-insp-traffic

type of class-card inspect correspondence sdm-cls-VPNOutsideToInside-10

game group-access 113

type of class-card inspect all sdm-service-ccp-inspect-1 game

http protocol game

https protocol game

type of class-card inspect entire game PAC-cls-icmp-access

match icmp Protocol

tcp protocol match

udp Protocol game

type of class-card inspect correspondence ccp-invalid-src

game group-access 100

type of class-card inspect correspondence ccp-icmp-access

corresponds to the class-ccp-cls-icmp-access card

type of class-card inspect correspondence ccp-Protocol-http

match class-map sdm-service-ccp-inspect-1

!

!

type of policy-card inspect PCB-permits-icmpreply

class type inspect PCB-icmp-access

inspect

class class by default

Pass

type of policy-card inspect sdm-pol-VPNOutsideToInside-1

class type inspect sdm-cls-VPNOutsideToInside-1

inspect

class type inspect sdm-cls-VPNOutsideToInside-2

Pass

class type inspect sdm-cls-VPNOutsideToInside-3

Pass

class type inspect sdm-cls-VPNOutsideToInside-4

Pass

class type inspect sdm-cls-VPNOutsideToInside-5

Pass

class type inspect sdm-cls-VPNOutsideToInside-6

inspect

class type inspect sdm-cls-VPNOutsideToInside-7

Pass

class type inspect sdm-cls-VPNOutsideToInside-8

Pass

class type inspect sdm-cls-VPNOutsideToInside-9

inspect

class type inspect sdm-cls-VPNOutsideToInside-10

Pass

class class by default

drop

type of policy-map inspect PCB - inspect

class type inspect PCB-invalid-src

Drop newspaper

class type inspect PCB-Protocol-http

inspect

class type inspect PCB-insp-traffic

inspect

class class by default

drop

type of policy-card inspect PCB-enabled

class type inspect SDM_VPN_PT

Pass

class class by default

drop

!

security of the area outside the area

safety zone-to-zone

zone-pair security PAC-zp-self-out source destination outside zone auto

type of service-strategy inspect PCB-permits-icmpreply

zone-pair security PAC-zp-in-out source in the area of destination outside the area

type of service-strategy inspect PCB - inspect

source of PAC-zp-out-auto security area outside zone destination auto pair

type of service-strategy inspect PCB-enabled

sdm-zp-VPNOutsideToInside-1 zone-pair security source outside the area of destination in the area

type of service-strategy inspect sdm-pol-VPNOutsideToInside-1

!

!

crypto ISAKMP policy 1

BA 3des

md5 hash

preshared authentication

Group 2

lifetime 28800

ISAKMP crypto key address 83.xx.xx.50 xxxxxxxxxxx

!

!

Crypto ipsec transform-set ESP-3DES esp-3des esp-md5-hmac

!

map SDM_CMAP_1 1 ipsec-isakmp crypto

Description NY_NJ

the value of 83.xx.xx.50 peer

game of transformation-ESP-3DES

match address 101

!

!

!

!

!

interface BRI0

no ip address

no ip redirection

no ip unreachable

no ip proxy-arp

penetration of the IP stream

encapsulation hdlc

Shutdown

Multidrop ISDN endpoint

!

!

interface FastEthernet0

!

!

interface FastEthernet1

!

!

interface FastEthernet2

!

!

interface FastEthernet3

!

!

interface FastEthernet4

!

!

interface FastEthernet5

!

!

FastEthernet6 interface

!

!

interface FastEthernet7

!

!

interface FastEthernet8

no ip address

no ip redirection

no ip unreachable

no ip proxy-arp

penetration of the IP stream

automatic duplex

automatic speed

!

!

interface GigabitEthernet0

Description $ES_WAN$ $FW_OUTSIDE$

IP address 89.xx.xx.4 255.255.255.xx

no ip redirection

no ip unreachable

no ip proxy-arp

penetration of the IP stream

NAT outside IP

IP virtual-reassembly

outside the area of security of Member's area

automatic duplex

automatic speed

map SDM_CMAP_1 crypto

!

!

interface Vlan1

Description $ETH - SW - LAUNCH INTF-INFO-FE 1 to $$$ $ES_LAN$ $FW_INSIDE$

IP 192.168.0.253 255.255.255.0

no ip redirection

no ip unreachable

no ip proxy-arp

penetration of the IP stream

IP nat inside

IP virtual-reassembly

Security members in the box area

IP tcp adjust-mss 1452

!

!

IP forward-Protocol ND

IP http server

local IP http authentication

IP http secure server

IP http timeout policy slowed down 60 life 86400 request 10000

!

!

IP nat inside source overload map route SDM_RMAP_1 interface GigabitEthernet0

IP route 0.0.0.0 0.0.0.0 89.xx.xx.1

!

SDM_AH extended IP access list

Note the category CCP_ACL = 1

allow a whole ahp

SDM_ESP extended IP access list

Note the category CCP_ACL = 1

allow an esp

!

recording of debug trap

Note access-list 1 INSIDE_IF = Vlan1

Note category of access list 1 = 2 CCP_ACL

access-list 1 permit 192.168.0.0 0.0.0.255

Access-list 100 category CCP_ACL = 128 note

access-list 100 permit ip 255.255.255.255 host everything

access-list 100 permit ip 127.0.0.0 0.255.255.255 everything

access-list 100 permit ip 89.xx.xx.0 0.0.0.7 everything

Note access-list 101 category CCP_ACL = 4

Note access-list 101 IPSec rule

access-list 101 permit ip 192.168.0.0 0.0.0.255 192.168.7.0 0.0.0.255

Note access-list 102 CCP_ACL category = 128

access-list 102 permit ip host 83.xx.xx.50 all

Note access-list 103 CCP_ACL category = 0

Note access-list 103 IPSec rule

access-list 103 allow ip 192.168.7.0 0.0.0.255 192.168.0.0 0.0.0.255

Note access-list 104 CCP_ACL category = 2

Note access-list 104 IPSec rule

access-list 104 deny ip 192.168.0.0 0.0.0.255 192.168.7.0 0.0.0.255

access-list 104. allow ip 192.168.0.0 0.0.0.255 any

Note access-list 105 CCP_ACL category = 0

Note access-list 105 IPSec rule

access-list 105 allow ip 192.168.7.0 0.0.0.255 192.168.0.0 0.0.0.255

Note access-list 106 CCP_ACL category = 0

Note access-list 106 IPSec rule

access-list 106 allow ip 192.168.7.0 0.0.0.255 192.168.0.0 0.0.0.255

Note access-list 107 CCP_ACL category = 0

Note access-list 107 IPSec rule

access-list 107 allow ip 192.168.7.0 0.0.0.255 192.168.0.0 0.0.0.255

Note access-list 108 CCP_ACL category = 0

Note access-list 108 IPSec rule

access-list 108 allow ip 192.168.7.0 0.0.0.255 192.168.0.0 0.0.0.255

Note access-list 109 CCP_ACL category = 0

Note access-list 109 IPSec rule

access-list 109 allow ip 192.168.7.0 0.0.0.255 192.168.0.0 0.0.0.255

Note access-list 110 CCP_ACL category = 0

Note access-list 110 IPSec rule

access-list 110 permit ip 192.168.7.0 0.0.0.255 192.168.0.0 0.0.0.255

Note access-list 111 CCP_ACL category = 0

Note access-list 111 IPSec rule

access-list 111 allow ip 192.168.7.0 0.0.0.255 192.168.0.0 0.0.0.255

Note access-list 112 CCP_ACL category = 0

Note access-list 112 IPSec rule

access-list 112 allow ip 192.168.7.0 0.0.0.255 192.168.0.0 0.0.0.255

Note access-list 113 CCP_ACL category = 0

Note access-list 113 IPSec rule

access-list 113 allow ip 192.168.7.0 0.0.0.255 192.168.0.0 0.0.0.255

not run cdp

!

!

!

!

allowed SDM_RMAP_1 1 route map

corresponds to the IP 104

--------------------------------------------------------

I only give your router cisco 892 because there is nothnig much to change on linksys wrv210 router.

Hope someone can help me. See you soon

You can run a "ip inspect log drop-pkt" and see if get you any what FW-DROP session corresponding to the traffic you send Linksys to the main site. Zone based firewall could be blocking traffic initiated from outside to inside.

A Site at IOS IPSEC VPN and EIGRP

Hello

I have a connection of remote site to base via a VPN IPSEC router. I don't want to run EIGRP accoss VPN. Howerver I want adverstise the rest of the network from the router of core of the subnet to the remote site.

The remote VPN subnet is managed as a route connected on the router base?

Configuriguring a statement of network to the remote site on the router base will cause EIGRP announce the road?

You are right.

RRI (reverse Route Injection) is the correct way to announce remote routes as static routes on the HUB, and all what you need to do is redistribute static in EIGRP, so she is redistributed in your EIGRP.

Here is an example configuration:

http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00809d07de.shtml

(It's about OSPF and IPSec VPN dynamics, however, the concept is the same for ipsec site-to-site and redistribution in EIGRP)

Hope that helps.

IPSEC VPN site to site on Transparent mode

Similar Questions

Maybe you are looking for