Is on a Pavilion DV9700 SATA I or SATA II HARD drive controller

Similar Questions

• Satellite P200-13Z - upgrade the hard drive - can I use SATA II hard drives?

  I have a Satellite P200-13Z with simple standard Fujitsu 120 GB SATA hard drive. I want to change this to a RPM SATA II 250 GB Western Digital 7200 RPM drive. This interface SATA laptop does support SATA II? Thank you very much!

  Not your portable computer does not support SATA II.

  However, you can buy the SATA II hard drive and put it in your laptop. Only way to get it going is to restrict the new speed of SATA HDD, I accelerate. To do this is to introduce a jumper on the drive to restrict it to SATA I speeds up. Once it's done put in your laptop and viola, it works.

  Good luck, but I would like to get a toshiba technician to install it if its under warranty. It's for your own good, so you don't turn your laptop into a boat anchor.

• Advice on moving 1.5 to SATA 2 HARD drive and put the Samsung SSD on SATA 1...

  My plan is to make a DVD of W10 MS

  Power off

  Unplug 1.5 to boot/storage HDD SATA 1

  Connect Samsung SSD SATA 1

  Turning and fresh install MS W10 on SSD and let it update

  Then, can I plug 1.5 to SATA 2 HARD drive and make it just my storage via disk management?

  What steps/tips to make this an easy transition?

  Paul

  It should not matter if you use SATA1 or SATA2, but there are always exceptions.

  I got a motherboard with two different SATA [Intel & Marvel] controllers with different speeds. It is unusual, so the safest bet is to use the same SATA connector for your new SSD that you used for your old HDD.

  Since you have two bootable disks, you may need to go into EUFI/BIOS and set your boot order to boot from the new SSD first.

  You should be able to access the files on the old drive without problems, but I've seen on occasion where you will get an "Access denied" error due to 'permissions' problems, especially if the original/OS disk has been protected by a password. If you have any questions, you can create a linux live boot disk "to access your files.

  Instead keep you the old drive as is, with an operating system and boot volumes on it, you must backup/move your important files to your new SSD then remove all volumes on the old disk, create a volume, and then format to use as a data/backup drive.

  If you found my answer helpful please say thank you by clicking on the icon of the thumb.
  If my answer has solved your problem, please mark it as accepted Solution. Thank you!

• I have a HP Pavilion dv7 and my agreement now bad hard drive to the Geek squad. Do you know where I could buy the recovery disk?

  I have a HP Pavilion dv7 and my agreement now bad hard drive to the Geek squad. My problem is that I'm not able to find my recovery disc and HP has no more of them. Do you know where I could buy the recovery disk?

  The official win7 ISO images can be downloaded here;

  http://www.w7forums.com/official-Windows-7-SP1-ISO-image-downloads-t12325.html

  You download the version installed on your HP, burn a dvd using ISO, software, the burning at the slowest speed, on quality discs, then install it using the Win Key on the label on your PC.

  You will then need to install specific drivers of HP, not of the preinstalled HP software will be at your disposal

• Pavilion Entertainment PC dv6: need a new hard drive for the dv6-1230us

  My question is about the HP Pavilion Entertainment dv6-1230us PC. Recently, it was abandoned, and since then it has been giving me the following message if poster every time it starts.

  Not found boot device
  
  Please install an operating system on your hard drive.
  
  Hard Drisk (3F0)
  
  F2 System Diagnostics
  
  "For more information, please visit: www.hp.com/go/techcenter/startup"
  
  I know it's important to run the hard drive test, but when I run the diagnostics of the system for the Test drive, it says:
  "HDD test failed.
  There is no hard drive.

  I was also on the proposed site and even after "reset my BIOS to default", it recommends running the hard drive test, which does not simply because it has not really helped me the "there is no hard drive. There was a YouTube video that I came across thus suggested pulling the hard drive and diconnecting and reconnect to correct the error in this case that the son is detached, but that no longer works.

  SO, I don't know if there is anything more that I can do, I guess that the hard drive is super dead.

  It comes with a Seagate ATA hard drive. I was wondering if I could replace it with a SATA hard drive or should it be an ATA? (Even has the material capacity to support a SATA drive?)

  Also, it is even useful to replace the hard drive? Should I get a new laptop instead? This laptop is used mainly for just browsing online and checking emails.

  Any help is appreciated, thanks.

  Yes, the hard drive is so dead, that he not yet register as a hard drive. The dv6-1000 series certainly uses SATA, not ATA drives so I'm not sure of what you see. You can replace it with any drive SATA 2.5 inch width 9.5 mm thick.

  Watch this video between: 53 and: 59 and see that it's a SATA drive. If yours is different, so you have confused with your model.

  https://www.YouTube.com/watch?v=QQx7PlIXFuE

  Hard disks are a small fraction of the cost of a laptop and if your what it takes to, I would say that to replace the hard drive rather than buy a new one.

  It is an excellent drive at a great price:

  http://www.Newegg.com/product/product.aspx?item=N82E16822236563

  You have recovery discs? You run Windows 7? Post back if you need help more to restore system software.

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• HP PAVILION H8 - 1280t: backup on another PC hard drive.

  I have to return my computer to HP.  Before I do, I want to remove the hard drive and connect it to my new computer and back up all my files.

  Can someone tell me the settings/connector on the hard drive?  I know that it is must be configured as a secondary hard drive, and I think it means it must be defined as a slave.  I also know that the jumpers on the hard drive set as slave used as a configuration.

  Advice would be appreciated.  I think than tht I have 48 to 96 hours for this task.

  THANKS IN ADVANCE: DAVID HALL

  ALL THE SPECIFICATIONS OF MY COMPUTER ARE LISTED BELOW.

  HP PAVILION SPECIFICATIONS

  H8 - 1280t Intel (Pittsburgh)

  SERIAL NUMBER: 2MD2110TVV

  10 PROFESSIONAL 64-BIT WINDOWS

  Motherboard is a Megatron

  Name of the MOTHERBOARD: IPIWB-PB

  HP/COMPACT NAME: PITTSBURGH

  USB 3.0 Blackbeard HPE 2 x USB3.0 ALBUMS of I/o PORTS + 4 X USB2. O

  POWER: 600 W Μatx ESTAR v5 HF PSU (Petrus)

  Processor: Intel Core i7 - 3930 K CPU

  RAM: 16 GB DIMM DDR3-1600 RAM 4X4GB WE

  Graphics card: AMD Radeon HD 7570 1 GB DDR3 FH PCIe x 16 Eyefinity

  Chipset: Intel x 79 Express

  Processor upgrade information

  • TDP: 130W
  • Socket type: LGA 2011
  • Motherboard supports the following processor upgrades:
  • • 38xx Intel core Quad (Sandy Bridge-E) processor
    • Intel 39xxK processor with Six cores (Sandy Bridge-E)
    • 39xxX Intel processor with Six cores (Sandy Bridge-E)
    • Intel i7-38xx Quad core processor

  Memory upgrade information

  • The four-channel memory architecture
  • Four DIMM DDR3 240-pin connectors
    NOTE:
    Two of the four DIMM slots are not extensible, because the liquid cooling system must be removed to replace the memory modules. Liquid cooling system is not available on all models.
  • Supports the following:
  • • PC3-10600 (DDR3-1333)
    • PC3-12800 (DDR3-1600)
  • Memory non - ECC, unbuffered
  • Supports 1 GB, 2 GB, 4 GB and 8 GB DIMMS
  • Supports up to 4 GB on 32 - bit systems
    NOTE:
    32-bit systems cannot resolve a full 4.0 GB memory
  • Supports up to 32 GB on 64 - bit systems
    NOTE:
    Maximum memory shown reflects the ability of the material and may be more limited in the operating system.

  Video

  Graphics

  • Integrated graphics is not available on this motherboard.
  • Two PCI Express x 16 slots (Gen 2.0)

  Expansion slots

  • Two PCI Express x 16 (Gen 2.0)
  • Two PCI Express x 1 (Gen 2.0)
  • A PCI Express Mini Card

  I/o Ports and internal connectors

  Rear i/o ports

  Figure: Rear i/o ports

  • S/PDIF
  • USB 2.0: 4
  • LAN (ethernet)
  • USB 3.0: 2
  • Audio: central/subwoofer
  • Audio: output rear speaker
  • Audio: speaker output side
  • Audio: line-in
  • Audio: output
  • Audio: microphone

  Internal connectors

  • 1 x ATX power connector
  • 1 x EATX 12V power connector
  • 1 x CPU fan connector
  • 1 x system fan connector
  • 1 x connector for fan VRM
  • 1 x connector for pump fan
  • 6 x SATA 3.0 connectors
  • 1 x connector audio front panel
  • 1 x connector recovery ROM
  • 1 x SMB connector
  • 1 x front panel connector
  • 3 x USB 2.0 connectors
  • 1 x USB 3.0 connector

  Configuration jumpers

  CAUTION:

  Don't change any rider when the computer is turned on. May damage the motherboard.

  Clear the CMOS settings

  This motherboard has a jumper to clear the Real Time Clock (RTC) RAM in the CMOS.

  1. Turn off the computer and unplug the power cord.
  2. Move the jumper to clear for 5 to 10 seconds, then move the jumper to return by default.
  3. Plug the power cord and turn on the computer.
  4. At the next boot, enter the BIOS to re - enter the user parameters.

  Erase PASSWORD settings

  The BIOS password is used to protect the settings of the BIOS against unwanted changes.

  To clear the password BIOS follow these steps:

  1. Turn off the computer.
  2. Move the Clear jumper.
  3. Turn on the computer to POST screen
  4. Turn off the computer.
  5. Move the jumper to the default return
  6. Enter the BIOS to check or set the new settings

  If the host computer does not start, it's a maybe clone, depending on the reason for the "no boot".  If it's because of a hardware problem, so it might still work, but the best way is to use another computer and connect the hard drive to the PC using an external adapter USB to SATA, THE problem: http://www.amazon.com/SANOXY-A12940-Drive-Adapter-Converter/dp/B001OORMVQ

  Then clone it on an external hard drive or use software backup, or both, just to be sure.  You said that there is an another computer available, then go ahead.

• HP Pavilion dv4-2049us suggestions to replace the hard drive of 250 GB? SMART disk error

  Any suggestions what to buy to replace the hard drive to a hard drive of 250 GB of HP Pavilion dv4-2049us that failed?

  SMART hard disk error (SMART check: failed)

  Failure ID: 0LJ8QF-5096HN-XD7XHA - 60CT 03

  Product ID: VV662UA #ABA

  Appreciate any help.

  Hello:

  Chapter 3 of the service manual indicates that you can go to a 500 GB 7 200 RPN SATA II HDD.

  http://h10032.www1.HP.com/CTG/manual/c01963667.PDF

  I recommend these to this provider if you live in the United States.

  500 GB:

  http://www.Newegg.com/product/product.aspx?item=N82E16822136856

  320 GB:

  http://www.Newegg.com/product/product.aspx?item=N82E16822136280

  250 GB: (the 320 GB drive is cheaper)

  http://www.Newegg.com/product/product.aspx?item=N82E16822136279

  You will also need to order a set of recovery disks to reinstall the operating system and the programs supplied with your PC if did you not have a game when you got the laptop.

• HP Pavilion dv7t-4100 CTO Entertainment Notebook PC Hard Drive replacement

  Hello

  I have HP Pavilion dv7t-4100 CTO Entertainment Notebook PC, and I had problems with hard disk of the guarantee period. for example I buy in 2010 and had a hard drive replaced in 2011 and 2012. Next time, he failed in 2013 (almost 11 months apart on average).

  The last time it failed, the warranty has expired so I thought to give it a try as employment through fixing/amortization of bad sector seagate software, Toshiba... that came out of Smart Drive Error.

  I use the HARD drive for some time now, but want to be ready for the next round and I don't know that he's going to be gone for good next time.

  Current HARD disk is 640 GB, 7200 RPM hard drive (replaced in 2012). HP 621046-001 manufacturer.

  When replacing, can I use ANY hard drive 640 GB? Can I use a hard drive that is higher than 640 GB? Different RPM?

  Any suggestions on hard drive?

  The recovery discs I had received with the replacement drive did not work properly. I had to use the first game I had created just after I bought the laptop.

  Thank you.

  -Pratik Patel

  I think that 160GB 2.5 "SATA III SSD is good for the system.

  Thank you

  visruth

• HP Pavilion dv9000 - XP does not see the HARD drive, how to install it?

  Hello

  I try to install XP SP3 on HP Pavilion dv9000, but XP Setup does not see the hard drive.

  Can you please point me in right direction - what I do files and how to add them to the XP SP3 installation CD necessary?

  I guess that somewhere there is a step-by-step detailed guide.

  Thank you

  Enter the BIOS by pressing F10 at startup. If you have the option of Bios Setup to disable the native sata mode, XP will install without problem, no sata driver needed. It will be on the tab of the System Configuration.

  
  If you do not have the setting in the Bios, it's the driver sata for your machine:

• Why my hp Pavilion making a great noise as the hard drive is the race?

  HP Pavilion a6430f

  Windows Vista Home Edition

  32 bit

  no error msg

  no change

  jguevarajr,

  Hard drives spin at a constant SPEED. Allows to study the fans:

  http://support.HP.com/us-en/document/c01474069

  How to clean the dust: http://support.hp.com/us-en/document/bph07153

  What Miss me is the instructions on cleaning the front end, so I've included the upgrade/REPAIR: http://h10032.www1.hp.com/ctg/Manual/c00841410.pdf

  See the excerpts 1-5 to remove the side panel and the front panel. Clean the cover (front and back) and the low forehead, area F on pg7. The front panel has usually a grid or slots at the bottom. It's the front air intake. Imagine all the unwanted blocked upward, you will find.

  For the air flow, never place the unit on a mat. If a floor, I found that place it on a 4 "top box will increase air. Make sure that the front panel extends beyond the edge of the box.

• Pavilion a6500f: can I use my old hard drive as a second drive to the new I install.

  I have a Pavilion a6500f I can access is no longer as he continues to tell me there are registry errors.  My recovery disk (I got a) or do a hard reset or else he will start.  It came with a window that says recovery system or start Windows normally.  I get a new hard drive to it and have a whole new Windows 7 installed.  The thing is that I don't want to lose all my stuff on the old hard drive.  So my question is can I install the OLD hard drive as a second drive to the new?  If I can then I can just copy all the files from the old drive to the new and use the old as a memory drive.

  Any help will be greatly appreciated.

  The simple answer is Yes.

  (1) I would like to replace the hard drive with the same drive size or larger. But does not exceed 2 T.

  (2) I hope you made the original recovery DVD set the original recovery firstly, DVD media DVD + R try as these will save you having to create a driver disk.  If you really have to buy a complete set of recovery, get it here. It will have all the necessary drivers.  Only $27.00

  (3) I copy the files and destroy the old disk. Its usefulness is damaged since 2008.

• Sat 1130 - HARD drive replacement

  I do work on a Sat 1130 where it seems that the HARD drive has failed. I was invited to replace it, but I can't go into the machine to do the job. I have seem some positions to have to take to a service centre, but it is released or guaranteed, if the owner is not bothered about what is y.

  Can anyone advise me on the way out the old HDD please.

  Thanks in advance for your help.

  Thanks for the info. ;)

• Pavilion 15-n275sr (F8T40EA): 15-n275sr replacement hard drive

  Hello world

  Just bought the laptop (HP Pavilion 15-n275sr) and who seek to replace his drive with an SSD, one HARD original. But do not know how to get access to the hard drive Bay. Someone would be able to provide instructions or video on how do?

  Thanks in advance!

  Best regards

  Greg

  The hard drive in your ntoebook is not listed as a because the removal and the replacement Crus requires major disassembly of the laptop.

  If you accept full responsibility, doesn't bother me violate the guarantee and uncomfortable with doing replace yourself, then here is the maintenance and service guide. Look for resplacement of hard disk. Looking for a PM. Your laptop has an AMD or Intel CPU?

• Satellite A200 - 1 GB does support SATA 300 HARD drive?

  I want to spend my Sat A200 - 1 GB hard disk with a 7200 RPM one... but they are all SATA300 models.
  Is this speed mode supported by the bios, motherboard and sata controller of this laptop?

  I just want to be sure that the hard drive works at its maximum speed capability and the sata and the mobo will not be a bottleneck...

  If Yes, the sata controller driver whichsis?... I want this wake in my own vista installation disc.

  Hello!

  Yes, you can use a disk with SATA300 mode but it only works in normal mode SATA no more at maximum speed. The Satellite A200 supports only SATA 1.0 mode (SATA150).

  You can use a HARD drive with 7200 RPM, this isn't a problem.

  What HARD drive capacities are supported, that you can see in the user manual. Look in Chapter 1.

  The SATA driver is in the Intel Storage Manager package.

  Good bye

• Pavilion g6-2165sx: * URGENT Please HELP * short hard drive DST has no error RU773W-68R81S-MFPX1G-60W803

  Hello my problem occurred as a result of the creation or modification of partitions to install ubuntu (for reasons of college) however I stupidly didn't check my disk was dynamic or basic and unfortunately it was dynamic, if after failing to install ubuntu windows 10 had an error in INACCESSEBLE_BOOT_DRIVE when I oppened the cmd troubleshooting and checked on diskpart did not exist but with a status unknown after dvd player I made the diagnosis and that he got a short DST has not... Is there a chance to correct the reader because im out of warranty and im in no condition to buy a new hard drive... Thanks in advance

  @Alin742

  Go to this site and create a bootable CD.

  http://hddguru.com/software/2005.10.02-MHDD/

  Boot from the CD.

  If she asks do you want SCSI, click No or just press ENTER. (countdown to 30 seconds)

  The port selection select your HARD drive. (Usually 1, 3 or 6).

  If you do not see your HARD drive, you will need to restart and go into the BIOS and SATA ATA value.

  After choosing your type of HARD drive, ERASE and press to enter. (This will erase all data).

  Leave it to erase the entire disc. (Depending on the size, it may take 2 to 5 hours.)

  Once done erase all disk F4 2 hit shots and will start the test.

  Many people simply replace the HARD drive and all that is wrong is there is simply soft errors. (Errors caused by software not hardware errors.)

  If you need help running the program let me know.

  REO