Is that process of read/write from the disk?

Similar Questions

• Bootcamp - Windows 10 should not see or read files from the disk HARD Apple intern.

  I have just successfully Windows 10 next OS X on my 15 "Macbook Pro mid-2014.

  Windows 10 should not see or read files from the disk HARD Apple intern.

  Should which driver I uninstall?

  On OSX, if the following Terminal command produces any output, then you cannot read partition OSX on the side Windows? FileVault2 will also disable access to the OSX partition.

  Cs diskutil list

• How to read continuously from the rs232?

  Hello

  I'm new to LabVIEW and my questions would be obvious for some for you. So please help if you know the solution.

  It's for my school project. For your information, we need to schedule a Committee of Altera DE2 to control traffic lights (something like that) and at the same time, the Commission shall forward the States of enlightenment to a computer with LabVIEW installed via an RS-232 cable.

  The rest of the project was fine except for the part of LabVIEW, because as I said earlier, I'm new to LabVIEW.

  We use the "basic series write and Read.vi" in the folder examples of NEITHER. The problem is that we do not know how to change the vi in order to receive the data that come the DE2 Board permanently. Each time, the vi stops reading after receiving 24 bytes of data.

  So, the first question is:
  1.) how to read continuously from the RS-232 port? (We tried to use while "loop" but without success, maybe we were doing it the wrong way.) If you know the solution, please enlighten us for us in a detailed manner.

  (2) Secondly, once we have received the 'chain', how can convert us to bits (0 and 1) so that we might be able to manipulate the bits, for example turn on the LEDs that correspond to the bits.

  Thank you.

  Instead of reading the bytes of the port so to read that many bytes (which may be zero), just do a VISA read for 1 byte.  He will wait for this next byte.

  To get an array of Boolean out of this byte, use this code.  He turns the characters into a byte array.  Takes the first and the only element of this array, and then converts this single U8 number into an array of bytes.

  

  Which country are you?  I've never seen or heard lights orange before.  Only the yellow lights.

• Acrobat Reader - not enough permissions to write to the disk

  Howdy,

  
  

  Tried to install Acrobat Reader DC on my MacBook. OS X 10.10.4

  
  

  Installation was immediately interrupted by this message:

  
  

  "The installation failed. Not enough permissions to write to the disk.

  
  

  Any help would be appreciated

  
  

  -Ned

  
  

  Hi Ned,.

  You have any Adobe application installed on your system, if so please check the permissions for the folder ~/Library/Application Support/Adobe (where ~ indicates your user directory).

  Select the Adobe folder, right-click and choose "Get Info" from the menu, expand the sharing tab and Permissions at the bottom of the window and check that your user account has the permissions read & write.

  If it doesn't matter what previous version of Adobe Reader is installed, uninstall it completely, restart your system & try to install Adobe acrobat reader Adobe - Adobe Acrobat Reader Distribution DCDC.

  Let me know how it goes.

  Kind regards

  Nicos

• Large number of unwanted emails that all appear to come from the same source

  Original title: spam E

  Currently, I get a lot of junk emails that all appear to come from the same source. I was put in my blocked list but the sender then change the address source slightly and I get more. Does anyone know how I can stop this. My address change my only option

  You use Windows Mail? Assuming that the subject field also changes, you could do a message like that rule.

  Start with the only rule of AddressBook and you receive a message that you want people not in your address book (E-mail from companies, bills, your ISP, etc), you can add them to the rule.

  Tools | Message rules | Mail | New.

  Box 1 - Where the From line contains people {check it out}

  Box 2 - Check: delete it & stop processing more rules if you want that messages not in the address book to go to deleted items.

  Box 3 - Click on the blue words contains people

  Click on the first address to select it. Scroll to the end and hold down the SHIFT key while you click the last address. This will highlight all. Right-click on it and click on from the menu that appears.

  Now, click Options and choose: Message * contains no of * the people below in the top of the page Options area, then choose: Message corresponds to one of the people below in the background Options box.

  OK your way out of the new rule.

  Now, only the addresses that you entered will be uploaded to your Inbox.

  Remember, if you add a person to your address book, you must add to the rule. It will not automatically be added.

  Be sure to see these links for more options.

  A few tips:
  http://insideoe.tomsterdam.com/tips/rules.htm

  Message rules does not? :
  http://www.insideoe.com/FAQs/why.htm#rules

• How to make that guest OS is separated from the host

  Have Win7 (16 GB of ram, 1 TB HD space) is a part of a Small Business Server 2011 domain.  I have a problem with the SBServer and want to look at a new facility to see certain folders permissions have by default. (user redirection folders does not, even if I set permissions per technet article).  Network is 192.168.1.x, can I install a Small business Server 2011 guest (that would be a trial of MS download) and make sure that it is completely separated from the win7 Host and, of course, the field. Then create one or two comments more OS on this same machine win7 and have these comments of BONES join Small Business Server customers?  If so, how do I set that up?

  Thank you, Steve

  Yes it's doable... read the documentation!   Setting up an isolated test with virtual network configuration is no different, so do it with a physical network.  In particular read Chapter 7 "Configuring network connections" in getting started with VMware Player (PDF).

• On the right of the adressbox, I always have Yahoo then Google, how can I solve that, I already delete Yahoo from the list in the box search, but every time I start firefox Yahoo is back. Thanks Ron Mijtelen ter, Amsterdam.

  Question
  On the right of the adressbox, I always have Yahoo then Google, how can I solve that, I already delete Yahoo from the list in the box search, but every time I start firefox Yahoo is back. Thanks Ron Mijtelen ter, Amsterdam.

  Hi Ron,

  Have you looked at article in the Knowledge Base using the search in Firefox bar? There are lots of good information in there. You happen to have an installed Yahoo! toolbar? You must disable or delete as well if you do. Try to start Firefox in Mode safe mode by holding down the SHIFT key while starting Firefox. If you have any problems using the safe, it's a matter of add-on or extension.

  Hope this helps!

• I have a project in iMovie HD6 and want export to Final Cut Pro.  I see that it is not possible from the previous questions, but is it possible that I could maybe create a dvd of the iMovie project and then who import in Final Cut?

  I have a project in iMovie HD6 and want export to Final Cut Pro.  I see that it is not possible from the previous questions, but is it possible that I could maybe create a dvd of the iMovie project and then who import in Final Cut?  I just want to make a new trailer for the project.

  What you suggest is possible but it takes software and third-party quality loss.

  Instead, export a QuickTIme movie. If you have a choice of codecs, choose Apple Intermediate Codec. You can save it where you want it-maybe in the movies.

  Then import the movie into FCP as a clip.

  Good luck.

  Russ

• I am trying to install windows xp from the disk, but it hangs during the installation process. no error code. It just hangs. What is the cause and what is the solution?

  I am trying to install windows xp from the disk, but it hangs during the installation process. no error code. It just hangs. What is the cause and what is the solution?

  Hello

  1. at what stage of the installation, the computer crashes?

  2. what operating system was installed on your computer prior to this?

  If you have the similar problem as mentioned in these links, you can follow these links and check if the problem persists:

  Windows XP Setup stops responding (hangs) during the "Preparing Installation" phase

  Windows XP does not meet the Message "Setup starts Windows XP"

  Hope the helps of information.

• URGENT! Nice day. I want to cancel the tariff for monthly payments that will be automatically withdrawn from the account today. Yesterday set a new annual rate. Asking for your help.

  URGENT! Nice day. I want to cancel the tariff for monthly payments that will be automatically withdrawn from the account today. Yesterday set a new annual rate. Asking for your help.

  Hi Agataa,

  Please refer to cancel your Adobe Creative Cloud membership

  Feel free to contact customer service if you have additional questions.

  Kind regards

  Shelly

• My DVD Maker 2 will not install the driver from the disk

  I recently bought a DVD Maker 2, but cannot load it the driver from the disk... Please notify that I searched for hours on the Internet for the free down load for my legacy but no luck, please advise...

  Hi L.A. Hastie,.

  ·         What version of the operating system is installed on the computer?

  I suggest to contact the manufacturer or check with the place where you bought the DVD maker for more information and help.

• If I have to start windows from the disk to do a repair, I lose all my data backed up?

  Computer will not complete boot. Happens to the black screen with green progress bar and stay there. The computer invites me to start from the windows disk. However, if I have to start windows from the disk to do a repair, I lose all my data backed up? Thank you.

  Computer will not complete boot. Happens to the black screen with green progress bar and stay there. The computer invites me to start from the windows disk. However, if I have to start windows from the disk to do a repair, I lose all my data backed up? Thank you.

  Hello

  in Vista, if using a Microsoft Vista DVD(NOT a Manufacturers recovery Disk), the "boot" disk repair process, you ask about, it's only a "Startup Repair", not a repair of the operating system installation; population

  You must have an operational Vista operating system to do a repair installation of the files using a Microsoft DVD of Vista system

  BUT, if the use and start from a manufacturers recovery disk, which guest from the disk is likely to reinstall the OS and lose all your data

  Please explain with more information

• Download black screen during installation of Windows 7 from the disk.

  Original title: loading Windows 7 with windows 8 is already installed

  Dell computer brand new.  (Terrible dealer. They charge $ for help on something other than the material.)  The new computer comes with windows 8 is installed.

  Like any windows 8.  Ordinate of windows 7.  They sent the disc and no key.

  Dell will not help with installation unless you pay them $!  They say that it's a Microsoft product, and they are not obliged to help, even if it was purchased from them!  It's like buying a new washing machine or a car.  You need to contact the manufacture to get help with it?

  No, you communicate with the store, it was purchased from.  This applies to any new product I know. But not with Dell!

  Sorry for the rant.  I just found this totally outrageous situation.

  MY PROBLEM:

  Installing windows 7 from the drive, they sent.  Ten minutes into it the screen goes all black.  It is said that there is a file on the disk.  Also a button to continue.

  I stopped the installation and am at a loss as what to do...

  Thank you, Al

  Hello

  Have you checked to see if your model computer has Windows 7 drivers available from Dell for it?

  If not, it will not install properly or work properly.

  Dell:

  http://www.Dell.com/support/drivers/us/en/19/ProductSelector

  ___________________________________

  Have you changed the order of startup and boot the Windows 7 disc, they sent you?

  You press F12 in a Dell to change the Boot order

  http://en.community.Dell.com/support-forums/desktop/f/3514/t/19500812.aspx

  Then do a clean install:

  http://www.SevenForums.com/tutorials/1649-clean-install-Windows-7-a.html

  ____________________________________

  Or ask Dell to replace the disc if it is faulty.

  ____________________________________

  Or download the correct ISO file and make your own drive and use the product key that is on the sticker COST Dell sent you.

  http://www.w7forums.com/threads/official-Windows-7-SP1-ISO-image-downloads.12325/page-2#post-124821

  And Neosmart has instructions on how to burn ISO disk images using imgburn:

  http://NeoSmart.NET/wiki/Burning-ISO-images-with-ImgBurn/

  By using the downloaded ISO file method can require the Activation of phone.

  If it does require phone activation, do not follow Demand of Auto, but brace yourself for a real person explain as to what has been done for purposes of re-setup

  "How to activate Windows 7 by phone '

  http://www.SevenForums.com/tutorials/18715-activate-Windows-7-phone.html

  The above method also requires that you go to your computer manufacturer's website > Support and downloads Section > locate your model number and operating system > then download and install the latest drivers for it.

   

  ________________________________________________

  Using the method of USB in conjunction with the Windows 7 download preceding:

  http://www.SevenForums.com/tutorials/2432-USB-Windows-7-installation-key-drive-create.html

  "How to get and use the Windows 7 USB/DVD Download Tool"

  http://www.SevenForums.com/tutorials/31541-Windows-7-USB-DVD-download-tool.html

  See you soon.

• Reading files from the internet and write them on a computer

  Hello
  
  I'm working on a program to copy files from a location on the internet to a local file on a computer.
  The file is a .swf file, so I read the data of the file on the internet in a ByteBuffer and then write it to a file on the computer...
  But it does not work... It copies the file, but the .swf run right
  However, when I use essentially the same procedure to copy a file from a local file to a local file on the same computer, it copies very well...
  As far as I know I'm copying the files in these two circumstances the same way, with only a few changes to connect to a URL...
  
  I can publish the source code in a day or two if it would help to explain better...
  
  Any help would be greatly appreciated!

  in. Read (Byte []) is not guaranteed to fill the table. You read in a loop until it returns-1.

  At the very least, check the return value from read() call. If it does not say that you have read the full file, there is your problem. If she says that you have it done read the complete file, then there is another issue that is not immediately obvious to me. I just hooked this one because he jumped in the eyes me like an obvious no-no.

• Write and read data from the user's local file system

  Hello

  I write my first extension for dreamweaver. My extension should backup the data on the local file system of the user. I know that I can use DWfile.read () and DWfile.write () as described in Chapter 2 of the Dreamweaver API reference. I store the data using the XML format. What is the best way to read and parse the XML data in the file? What is the best way to write the XML data in the file?

  If you recommend one format other than XML, I'm open to suggestions. The data are only a few configuration information for the extension which should be persisted.

  Thank you

  mitzy_kitty

  How will the data be used? If it is used by JavaScript, use JSON format which includes js. If you use XML, then you will need to find an XML parser to read the data.

  Randy