ISCSI EqualLogic PS6000 path problem

Similar Questions

• VMWare using only 1 IP of EqualLogic PS6000

  I have a new configuration of vSphere with 2 hosts ESXi (Dell R610s) and all my a new EqualLogic PS6000 storage. I use the Broadcom NIC for iSCSI (all other traffic exceeds a secondary NIC 4port). Right now I use 2 ethernet ports on the R610s and PS6000 for iSCSI. I followed the instructions in the document "setting up VMWare vSphere software iSCSI...". "Dell for 2 different iSCSI VMKernel interfaces configuration. The PS6000 uses an IP address of the 10.30.1.1 group and the 2 network cards are 10.30.100.1 and 10.30.100.2 (all with a 255.255.0.0 netmask). The problem I have is when I connect the R610s to the PS6000 via the IP 10.30.1.1, the PS6000 only redirects them to 10.30.100.1, forcing all traffic from these two hosts in the same VM. I tried connecting a computer non - ESX (my Mac desktop computer), and it sends me to 10.30.100.2, so this interface works without a doubt. What I'm trying to understand now, that is exactly how I have VMWare to connect two IPS to distribute the load between the two interfaces on the PS6000. The PS6000 reports 2 connections by volume of each ESX host.

  Does anyone have an idea what I should look next?

  Thank you.

  I opened several requests for EQL support about something similar to this.  In many cases when I migrated a table in an existing pool, or when I activated interfaces more I don't see connections spread.  I saw the following:

  -Select Eth1 and Eth2, wait a few hours, run IOMeter tests, all connections are always on Eth0

  -Restart the controller, now all connections are on Eth1 and Eth2 with none on Eth0

  -Wait as the rest of the weekend and check Monday, iscsi connections are balanced.

  The above situations have happened to me a few times and I have been informed that the balancer connection will be finally doing things.  I think something has changed with this code over time, it was that the balancer spreads connections very quickly.

  Ben

• Bad path problem, but how to fix?

  Hello
  
  If you go to http://www.enhancedwireless.net/Opportunities/manufacturers.shtml and select one of the sub menus under "Manufacturers" you should get a screen password challenge - click Cancel and you should get an authentication page. Now at the bottom there is a library item with 5 menu items dealing with all other pages, but this one.
  
  It must be a path problem, but I tried... /... / Library/footer, I tried... / library/footer, I tried/library/footer and I always get page not found when I click on any of these 5 points... there still place these links in the record of the manufacturer called opportunities, but it should link only to the correct page outside the opportunities folder.
  
  Thoughts?
  
  Thank you
  
  KO

  OK it's fixed... I changed all links to "/" only and kept the... / library has and it works now, thank you very much

  KO

• Equallogic PS6000 + ESX iSCSI storage redundancy: LUN disappears when 1 switch off!

  Hello everyone, this is my first post here

  OK, so as the title says, I'm working on the redundancy under ESX. Because network configurations can be quite confusing I just did a quick draft of our infrastructure with one of my 3 ESX host and will try to explain as clearly as possible, the configuration details.

  In my ESX host, I configured a new vswitch with the vmkernel and vmnetwork joined 4 (NIC 2,3,4 and 5) my card NETWORK is configured as active in the collection of NETWORK adapters (also tried to put 2 according to availability) method of failover is Beacon probe (also tried with the status of link)

  On another VSwitch I have the console service with the NIC (NIC 1 and 6) 2 of the joint.

  My 2 switches are connected by a SHIFT of 4 links and the RSTP Protocol is active and works (although I have a lot of broadcasting activities, as soon as I connect my LAN switch to the SAN switches, but that's another story)

  My SAN is connected with 2 links on A button and switch B 2 for each controller. I created 3 volumes on the SAN that is each configured in my host ESX 3. So far, everything is great.

  Now, I pull the power plug from the switch a. switch B takes the lead and I can still ping SAN network lan switch, I can ping my small guest VM but the virtual machine itself quickly dies. I can't even it reboot or I get an error message indicating that the file is not found. So I go to my store of data, and it is when I see that it's empty! I need to open any new analysis of the LUN to again access to the data store and start my VM.

  From my point of view, although ESX detects that some links are down when I pull the cord, the iSCSI session just dies on me and will not "restart". I read stuff on multiple paths, but the "manage paths" button is grayed out, I'm not even sure that's what I need.

  So basically, as you can see I am quite new to all this and completely lost when it comes to things of redundancy, hell, I didn't even know on the tree covering weight before yesterday! So, if any of you guys can give me some advice on the realization of redundancy I look forward ^^

  Thank you very much!

  I wouldn't put my vmnetwork and my storage on the same vSwitch network.  I separate them into their own vSwitch and use two natachasery for each vSwitch.

  Once you have the traffic separated out, I'll make sure a vmkping, and not a ping to the storage target runs through each physical NIC.  Remove all cables and one at a time to create works of course routing their connection.

  -KjB

  VMware vExpert

  -KjB

  VMware vExpert

• EqualLogic PS6000 Serires IP address changing

  Hello

  My logic equal group IP is 192.168.0.1 and my two other members of storage are 192.168.0.2 and 192.168.0.3 no port management "management of ports are not configured and is unable to be present due to the direction and iscsi are on the same subnet.

  I would like to change the IP address of the 172.16.10.2 group and my two 172.16.10.3 storage 172.16.10.4 "I want to get rid of the subnet 192.x in preparations of iscsi with the exception of the management ports."

  If I change the ip group at 172.16.10.2 and activate 1 Ethernet ports on the two members with IP 172.16.10.3 172.16.10.4, this group will still be intact and members can see each other in the group without problem?  or what I need to reset the devices of storage and everything again?

  * This is not a production system and contains no data on this subject yet.*

  Thank you

  Hello

  You don't have to reset the berries to change IP addresses.  Just do it slowly, I prefer the serial port as it will always be available when you change IPS.  At some point, you have a PC that has access to both networks.

  PS6000, alias Type 7 controller does not have a dedicated port of Mgmt.  If you want to use out-of-band management, you will lose the last GbE port for this feature.

  So assuming that you do not want to lose a GbE port, you must change a port on each Member new subnet...  This updates the internal members IP addresses table so that they will always stay in contact with each other.  When you get down to the last port, change the IP address of the Group on the new subnet.  Then change the default gateway for the new subnet on all members.  Then finally replace the last network ports on all members of the new subnet.

  I suggest you then restart the two members, a moment.

  If you have a contract of support in place, Dell support can help you in this process.

  Kind regards

• ESXi 6.0 challenges iSCSI Equallogic PS 6100

  Hi all

  I installed my Windows of 5.5 to 6.0 vCenter vCenter server.  At the same time, I wiped one of my Dell R710s 3 (3 years) to get a new installation, since it has been upgraded since ESXi 5.0.  I started with the Dell ESXi 6 disc.  Installation was smooth.  After you configure the host to match the configuration of my other two guests of ESXi 5.5, I couldn't have my Equallogic LUN to display.  Other LUN iSCSI (Drobo for backup, Openfiler to test) had no problem.  Only Equallogic and Nexenta.  The two without complain "Access denied" when the ESXi 6.0 Server tries to discover the San.

  By looking farther, two things have changed in ESXi 6 at face value: 1., My Broadcom NetXtreme II BCM5709 iSCSi cards are now registered as QLogic.  2. my software VMware iSCSI adapt now has a new name of the initiator.

  My Equallogic SAN running firmware 7.x.  To see if the pilot makes all the difference, I wiped the ESXi host once again and installed the version of VMware instead of Dells.  Now, my iSCSI network cards are a little different... ranked QLogic NetXtreme II.  Still, no luck on the SAN and errors on the persistence without 'access denied, or not allowed.

  I made sure I don't use CHAP or and ACL.  While the static tab to the Nexenta works (which means that he discovers all IQN) Lun never appear.  With the Equallogic, no IQN is discovered.

  I wanted to make this post to see if we can get this figured out and maybe after some good info if we get a resolution.  However, I don't have weeks to experiment, because I have to go back to vCenter 5.5 and recover the ESXi host.  Any help and suggestions would be appreciated!

  Hello

  On this page and update your firmware of hardware and its driver: VMware Compatibility Guide: search for i/o device

  Its brand name is also Qlogic

• System vi exec path problem

  Hello

  I have a problem with the exec system vi. As a first step; program work and the reason why I write here is what I want to do a little more functional program and remove an annoying bug.

  My front panel consists of two buttons, two controls of path, control of an image and a single string indicator. I intend to use this vi to enumerate CCD cameras on my computer, select on of them and acquire an image and then display them on the front panel. This is accomplished by the two external exe files calls via the exec system vi command. In the block diagram, I arranged the two calls into a structure of event encapsulated by a certain time so I can make calls during execution using two loop buttons.

  The first button is used to acquire images of a CCD camera. When I push the first button ('acquisition') the path of the first control path (pointing to the executable file of the program acquisition) is sent to an exec system vi (the path) and the separate folder name and collected image is then displayed in the controller of the photo.

  The second button is used to list the cameras available on the computer. In the same way that through the acquisition of power to an another exec system the chain of path from the second controller path is vi that lists the cameras and displays them in the text box.

  Now to the problem. When I start the program I select the two executable in their respective path controls, for example the exe of CQI, followed of the exe of the enum. If I press the CQI exec system VI associated with this path is started and the image appears. If I then press the button enum cam I get a file dialog box that wants me to locate the executable enum (even if the correct path is specified in its corresponding path control). If I select the path (again) when the dialog box is prompted the program works very well and the cameras listed are presented in the indicator chain. But if I now press the purchase button a dialog box if poster asking me to locate executable CQI and when I do, the CQI works very well, but yet, I can't list the cameras until I specify this control of trajectory.

  So, it seems that the correct loading of an exec system depend not only on the provided path, but also the path most recently loaded to any control of trajectory if there are several system exec.

  I am grateful for any help provided. Hope my question is clear enough and not specific.

  I run labview 8.6

  / Mikael

  You are stripping the path you're providing and send just the name of the file in the command line. This assumes that the command window has the defined PATH environment variable so that the executable can be found. You can't assume that. You should be by specifying the full path to the executable file as the command line. Be sure to include the path in quotes.

  A comment about code: what's the point of this loop? It doesn't do anything. Or the frame of the sequence. You don't want a structure of the event to be stowed until something happens. If you start something that could take a long time, then you should look through architecture such as the producer and consumer. You want the structure of the event to finish quickly, so you can continue to respond to the events.

• LabVIEW 2009 Build Path problem

  [Cross posted from LAVA]

  I got a code that worked fine on my home PC, when I moved to work, the exe would not build due to errors.

  Return errors are not good to explain the problem

  Until I got this one:

  

  Look at the path of the error:

  C:\Users\Developer2\Desktop\User group Meeting\LabVIEW 2009 new features\code\02 intermediate\01 build specifications\build file executable application. exe\LabVIEW 2009\vi.lib\addons\_ICON Library\String\_icon_lib_string.llb 9.0\my paths\dist\application

  This path refers to a VI inside of my executable!

  Maybe it's a bigger problem than I first thought

  So my question is:

  If a path inside my building that would be compared to the executable and LabVIEW must resolve, could fail, this process, depending on where the exe is located in a folder hierarchy?

  I guess it could have happened before? but it would be more probable now due to longer paths!

  Cross post solution

• Build a path problem in Eclipse

  I'm having a problem with Eclipse find Java interface that is generated from a resource file. I created the .rrc and .rrh files in my source tree. The interface file, however, is placed in a .tmp file that isn't on the build path Java, Eclipse complains that it cannot resolve the references to the interface and that you do not to import it. I can add the .tmp folder to the path to build in the project properties, which makes Eclipse happy, but he does not 'stick' - the next time I start Eclipse, .tmp is out of the way of construction. It also disappears each time that I add or remove a project class. What I am doing wrong?

  the jde creates the StringsResource.java file dynamically (in your tmp folder).
  You must add this file (or one that you created manually, depending on your workflow) in eclipse. No tmp of course folder, copy it into your project folder.
  do NOT add this file to the jde project.

• image path problem

  Hi all

  I installed apex 5 on windows 8.1 with ADR 3.

  When I configured with the pl/sql gateway, I could open the apex very well.

  but oracle says it is depricated and that we should be using restful services.

  now, when I tried to use restful services by disabling the pl/sql gateway and by running the stand-alone mode of ADR iin.

  java-jar ords.war

  When I navigate to the url

  localhost: 8080 / ADR

  I get this error

  There is a problem with your environment because Application Express not having files not loaded. Please check that you copied the images directory on your application server by following the instructions in the Setup Guide. Also, please check that your image prefix path is correct. Is your current path (it must contain both starting and ending oblique lines, such as the default/i /). Use the SQL script reset_image_prefix.sql if you need to change.

  

  Please guide me how to solve this problem?

  Thank you.

  Hi Maahjoor,

  Maahjoor wrote:

  somehow, I managed as below

  I disabled the mod pl/sql

  I run @apxldmig.sql directory (because my record of the apex is a little less app folder.)

  then I followed the documentations for the glass fish-Server deployment

  and finally I copy and rename ords/conf/apex_pu.xml to ords/conf/apex.xml

  and I was able to deploy on the glassfish server.

  Using the apxldimg.sql script is not required to load images in the ADR. The script is being used to load images in Embedded PL/SQL gateway when configuring EPG as a web server for Oracle APEX.

  If you want to set up images for Standalone ORDS and then use the following command:

  java -jar ords.war standalone --apex-images C:\app\apex\images
  

  You deploy ADR Oracle Glassfish Server (no need to order above) follow these steps:

  • Create an i.war using the following command:

  java -jar ords.war static C:\app\apex\images
  

  This command will create i.war with your reference to static images.

  Reference: http://docs.oracle.com/cd/E56351_01/doc.30/e56293/install.htm#AELIG7044

  • Log-in in the Glassfish Server Admin Console and deploy the i.war:

  Reference: http://docs.oracle.com/cd/E56351_01/doc.30/e56293/install.htm#AELIG7222

  For more information consult: ADR deployment on Glassfish Server

  Kind regards

  Kiran

• Morphing path problem

  Hello

  I'm running a problem trying to turn two forms (created using Illustrator).

  Here are the steps I took: (the problem is in bold)

  1. Imported two Illustrator files in AE and put them on the timeline in two distinct layers.
  2. Converted the two forms of vector layers
  3. Paths of alterations to two shape layers.
  4. Copy/Pasted the path of Shape1 on the timeline for Shape2.
  5. Changed 'First Vertex Point' for the two paths so that they are in the corresponding positions.
  6. After step # 5, morphing between the two railways retained 'twisty - effect' during Interpolation.
     
     I did some research and discovered that the other summits have been numbered probably not elsewhere due to I made them in Illustrator.
  7. To address the problem of summits, I copied the path of Shape2 and stuck in Illustrator, I used the "Reverse Path Direction" tool in the attributes Panel. (To do this, I pasted the path, then you press Command-8, then past the meaning of the path).
  8. Once the meaning of the path has been reversed, I pasted the path for Shape2 in the timeline for Shape1 and got the desired morph I wanted to (much more natural, non-twisty)
  9. However, now, the path for Shape2 moves to the upper-left corner of the Composition during Interpolation and I don't know why.  I checked and there is no enabled for movement of position keyframes.  (Anchor point for path crosses the top left of the computer)
     
     When I try to drag the way back in its normal position, the entire layer is moved.
     
     The problem seems to be solved when I paste the path in a different group in the same layer, however, I still have to manually set the positioning.  This workaround is problematic for the project I am working because the forms that I work with several paths. and by dragging each a return to manual position is not accurate, nor it is time-saving.  Note: I have not been able to enter values numerically position to solve this problem.  He has lived it all physical dragging.)
     

  What is causing the path to move over the Interpolation and how can I prevent it?

  I hope I was able to articulate the problems I encounter.  Any ideas would be greatly appreciated.

  Thanks in advance!

  In addition, some other info:

  Computer: Macbook Pro 13 retina "(end of 2012)
  Processor: 2.9 GHz Intel Core i7

  Memory: 8 GB 1600 MHz DDR3 (6.5 GB dedicated to active Adobe products)

  Graphics card: Intel HD Graphics 4000 1536 MB

  
  Using After Effects CC (13.5.0.347)

  Thank you, once again!

  on the way to Morphing:

  to create smoother transitions in the shape on the form, you can use the interpolation of mask - it creates intermediate keyframes between two path keyframes. Read about it here: management and animation of paths form and masks in After Effects . Unfortunately, this is for mask paths and not form. but you're smart - you can copy the path of a mask, do your thing and then paste it back. or maybe you don't have the form anyway. see if it works.

  on Offset of the path:

  I was able to reproduce the problem. Here's how I see it: when you convert layers have forms Ae, they get some position attributes so that they will be placed in the same position. Note If you click UU you get the changed properties:

  

  When you paste the path of illustrator you paste on a layer that has a lag of transformations and that is why your layer is up there.

  This, I do not understand:

  "To address the problem of summits, I copied Shape2 path and stuck in Illustrator, I used the"Reverse Path Direction"tool in the attributes Panel. (To do this, I pasted the path, then you press Command-8, then past the meaning of the path). »

  you don't need to copy paste EI AI and back when you can copy paste the original layer of AI to Ae. to do this, copy - paste only once. You can copy paste paths of the EI and ch AE too.

  Here's my suggested solutions (choose a! not all of them):

  1 reverse the way AI - save the file and convert the layer shape again - this way, you have no copy paste the way AI, but only of the Ae.

  2 reset the transformations and properties of position for the Group shape. then copy paste will be exactly where is your path.

  3. If you don't really need forms, you can work with layer masks and copy paste like crazy to AI without lag

• Reduce the number of iSCSI Multipathing in paths

  I'm experimenting with performance iSCSI on NAS. Currently I have 4 NICs on the host and 4 NICs on the NAS. That leaves me with 16 channels for iSCSI data store. I would like to disable multipathing so I find myself with 4 paths. I would try having NIC1 on the host go on the NAS NIC1 and NIC2 on the host then goes to NIC2 on the NAS, so on and so forth. Is this possible? I saw that I could disable paths but I did anyway to say which way goes to which nic so that I might finish with 4 paths all on the same network adapter. Any help would be appreciated.

  I found that if I broke to the top of each of the 4 NIC I used for iSCSI in different subnets traffic and then set the 4 network cards on the NAS in the same subnets I could get the number of paths down to 4. However with adapter for iSCSI for the VMware software there is no way to have more than 1 NIC of the flow value. Round Robin will use only 1 NETWORK with a value of debit card while I was stuck with the help of only 25% of the potential flow of the NAS for iSCSI traffic.

• iSCSI Multipathing - each path does refer to a specific target IP address?

  Dear Experts,

  I just set up a 6.0 ESXi host and a Synology NAS ds2015xs MPIO Multipathing. On the side of ESXi, I created two dedicated VMkernel with a physical NIC adapters each and every other network cards set to unused. I then added the adapters to the software iSCSI adapter in ESXi. On the side of SIN, I configured both interfaces in the same subnet as the VMkernel adapters. I then created a target which allows multiple iSCSI sessions, add LUNS and allowed access to the target for the IQN of the ESXi iSCSI Software adapter name.

  Back on the side of ESXi, I added a static discovery entry manually adding addresses to IP of NAS devices and target IQN. After a new analysis of the storage, ESXi showed two paths to the interface of the SIN for which I entered the IP address as a static discovery entry:

  

  With this configuration, multiple paths does not--once to stop the interface on the NAS, ESXi don't miss not automatically during the second interface of the NAS. After you have added a second static discovery entry with specifying the same target, but the second IP address of the NAS, ESXi showed all four lanes - two at each interface on the NAS:

  

  With this configuration, Multipathing works as expected. If an interface on the NAS fails, ESXi will automatically use a path for the second interface.

  In fact, it makes sense. At first, I was wondering about whether it is correct that I have to manually enter each interface of the target in order to obtain the corresponding paths to it. I first thought that I just need to enter an IP address of the target and that MPIO uses a kind of magic to automatically discover the paths to other interfaces available on the NAS. Later, I saw that this is the case when using dynamic discovery instead of static discovery. However, the same dynamic discovery adds all interfaces of the SIN as entries in static discovery. Once I have delete one of these entries in the list, the corresponding paths are also deleted.

  So my correct understanding that always information path refers to the corresponding IP address of the target and that a way will stop working once the corresponding IP address is no longer available?

  Thank you

  Michael

  When you configure access to storage, it is always important to follow the recommendations of the supplier. Not only to learn how the program setup the IP configuration, but also for the way political (e.g. Fixed, MRU, Round-Robin).

  Regarding your question, many storage arrays are configured with the extra VIP (virtual IP address) or IP address of the group, which is then used to configure the target (or another) dynamic on the ESXi hosts. When an initiator connects to such a VIP or group IP, the target will respond with all of its associated IP addresses. If this isn't an option for your storage device, you must provide all the IPS target manually (as you did).

  André

• Compound path problem

  Hello

  I'm having a problem with two tracks transparent, based on the same original piece of geometry. When I export to JPG, PNG or TIFF, I'm endangered art. PDF seems very well handle it. I would like to solve the problem, so I hope that someone here has the answer.

  (1) the "badge" is a compound path, I've tried to not a compound path, because my two transparent traces in the document are where the problem occurred. I can't do anything to NOT be a compound path. Illustrator does automatically transparent traces for each Boolean subtraction? If I release the it, the track breaks. None of the pathfinding tools give me subtracted geometry I want.

  

  Same shape, new problem:

  

  Does make sense to anyone?

  Thank you!

  p.s. I just noticed doing weird rendering in preview, as well. Look at the icon "Layer 1".

  

  Subtraction only works with transparent traces.

  You can check if the white fills overprint a your forms. Open the attributes Panel.

• Try to upgrade a PES 10 catalog Lightroom CC - problem: conversion file path problem [was: upgrade Photoshop elements catalog]

  Update 20150707:

  So I think I found the reason for the problem:

  About 60% of my files in my catalog of PES 11 are converted (or probably better: "sent") to Lightroom with a double slash "/ /" in the path of the file.

  This looks like: D:/photos/ /Keep, albums, 2002, 200212 < the rest of the way is OK >...

  Lightroom complains that it cannot find the file on the disk, probably because of the double slash.

  With more than 4,000 theses error Lightroom core dumps with a buffer overflow, probably due to the large number of error messages. Cup of the catalogue of PES 11 decline little by little I managed to identify the cause.

  The problem is that my PES 11 catalog is repaired, optimized and PES 11 think that the file is in the correct location and can open and edit it.

  So what do I do to make the two programs to understand each other with their file name conventions? ... or how to get rid of the second crime "/"?

  Thank you

  Thomas

  ---

  Good afternoon

  I'm trying to upgrade a PES 10 catalog Lightroom (Lightroom details below) CC - both on Windows 8.1 (details below as well)

  There are about 30,000 photos in the catalogue of PES 10. Import runs for awhile then LR CC shows a short message that it could not import all of the photos and then it is intercepted by a Windows operating system message that indicates «Lightroom has stopped working...» »

  He has imported about 3,500 photos and converted all the photos of Collections, but also in the tree of the key.

  I tried the following:

  (in PES 11)

  • optimized and repaired the catalog
  • removed all files types that LR does not support
  • removed all media offline

  (in LR cc)

  • Tried running in different compatibility modes
  • Tried running in administrator mode
  • Temporarily disabled any antivirus software

  I run LR CC successfully with a new catalog and it behaved very well through all operations. TI ROM dumps on the conversion of this catalogue. Importing photos from the catalogue above works fine hierarchy; just that it loses the key word and obviously knows no collections.

  Is there any log file indicating the element involved the conversion?

  I have to say that I love LR after a period of three weeks of the trial, but I'm not really ready to let go hold on 90% of my data meta at this stage.

  Best

  Thomas

  System Info for LR and PSE

  ---

  Version of Lightroom: CC 2015.0.1 [1018573]

  License: Trial

  Operating system: Windows 8.1 Business Edition

  Version: 6.3 [9600]

  Application architecture: x 64

  System architecture: x 64

  Number of logical CPUs: 4

  Processor speed: 3.1 GHz

  Built-in memory: 16199,9 MB

  Real memory for Lightroom: 16199,9 MB

  Real memory used by Lightroom: 364.6 MB (2.2%)

  Virtual memory used by Lightroom: 314,3 MB

  Memory cache size: 185.7 MB

  Maximum thread count used by Camera Raw: 4

  Camera Raw SIMD optimization: SSE2, AVX, AVX2

  System DPI setting: 96 DPI

  Composition of the Bureau enabled: Yes

  Exhibition: 1) 1920 x 1200, 2) 1920 x 1200

  Entry types: Multitouch: no, built-in touch: No, built-in pen: no, touch external: No, external pen: no keyboard: No.

  Graphic processor News:

  Check the supported OpenGL: failed

  Vendor: Intel

  Version: 3.3.0 - Build 10.18.10.3345

  Renderer: Intel(r) HD Graphics 4600

  LanguageVersion: 3.30 - Build 10.18.10.3345

  The application folder: C:\Program Files\Adobe\Adobe Lightroom

  Library path: C:\Users\behreth\Pictures\Lightroom\Lightroom Catalog.lrcat

  Settings folder: C:\Users\behreth\AppData\Roaming\Adobe\Lightroom

  Plugins installed:

  (1) Behance

  (2) substantive canon Plugin

  (3) Facebook

  (4) Flickr

  (5) attachment Plugin Leica

  (6) home Plugin Nikon

  Config.LUA flags: None

  Update Kit: Adobe Camera Raw to Lightroom 6.0 9.0 (build 1014445)

  Update Toolkit: book Module 6.0 (build 1014445)

  Update Kit: develop Module 6.0 (build 1014445)

  Toolbox update: Import Module 6.0 (build 1014445)

  Updated Toolkit: library Module 6.0 (build 1014445)

  Update Kit: Card Module 6.0 (build 1014445)

  Update Toolkit: monitor Module 6.0 (build 1014445)

  Update Toolkit: print Module 6.0 (build 1014445)

  Update Toolkit: Slideshow Module 6.0 (build 1014445)

  Toolbox update: Module Web 6.0 (build 1014445)

  Update Kit: com.adobe.ag.AgNetClient 6.0 (build 1014445)

  Update Kit: com.adobe.ag.AgWFBridge 6.0 (build 1014445)

  Update Kit: com.adobe.ag.Headlights 6.0 (build 1014445)

  Update Kit: com.adobe.ag.LibraryToolkit 6.0 (build 1014445)

  Update Kit: com.adobe.ag.MultiMonitorToolkit 6.0 (build 1014445)

  Update Kit: com.adobe.ag.archiving_toolkit 6.0 (build 1014445)

  Update Kit: com.adobe.ag.bridgetalk 6.0 (build 1014445)

  Update Kit: com.adobe.ag.catalogconverters 6.0 (build 1014445)

  Update Kit: com.adobe.ag.cef_toolkit 6.0 (build 1014445)

  Update Kit: com.adobe.ag.coretech_toolkit 6.0 (build 1014445)

  Update Kit: com.adobe.ag.curculio 6.0 (build 1014445)

  Update Kit: com.adobe.ag.discburning 6.0 (build 1014445)

  Update Kit: com.adobe.ag.email 6.0 (build 1014445)

  Update Kit: com.adobe.ag.export 6.0 (build 1014445)

  Update Kit: com.adobe.ag.ftpclient 6.0 (build 1014445)

  Update Kit: com.adobe.ag.help 6.0 (build 1014445)

  Update Kit: com.adobe.ag.iac 6.0 (build 1014445)

  Update Kit: com.adobe.ag.imageanalysis 6.0 (build 1014445)

  Update Kit: com.adobe.ag.layout_module_shared 6.0 (build 1014445)

  Update Kit: com.adobe.ag.pdf_toolkit 6.0 (build 1014445)

  Update Kit: com.adobe.ag.sdk 6.0 (build 1014445)

  Update Kit: com.adobe.ag.sec 6.0 (build 1014445)

  Update Kit: com.adobe.ag.socket 6.0 (build 1014445)

  Update Kit: com.adobe.ag.store_provider 6.0 (build 1014445)

  Update Kit: com.adobe.ag.substrate 6.0 (build 1014445)

  Update Kit: com.adobe.ag.ui 6.0 (build 1014445)

  Update Kit: com.adobe.ag.video_toolkit 6.0 (build 1014445)

  Update Kit: com.adobe.ag.xml 6.0 (build 1014445)

  Update Kit: com.adobe.wichitafoundation 6.0 (build 1014445)

  Map #1: Vendor: 8086

  Feature: 412

  Subsystem: 204a 8086

  Review: 6

  Video memory: 96

  Map #2: Seller: 1414

  Device: 8 c

  Subsystem: 0

  Revision: 0

  Video memory: 0

  AudioDeviceIOBlockSize: 1024

  AudioDeviceName: Speakers (Realtek High Definition Audio)

  AudioDeviceNumberOfChannels: 2

  AudioDeviceSampleRate: 44100

  Build: not initialized

  Direct2DEnabled: false

  GPUDevice: not available

  OGLEnabled: true

  ---

  10.0.0.0 elements Organizer

  Basic version: 10.0 (20110914.m.17521)

  Language version: 10.0 (20110914.m.17521)

  Current catalog:

  Catalog name: fitt_master_backup

  Catalog location: C:\data\pse11_catalog\fitt_master_backup\

  Size of the catalog: 135, 8 MB

  Catalog Cache size: 1, 1 GB

  System:

  Name of the operating system: 2000

  Operating system Version: 6.2

  System architecture: Intel CPU Family: 6, model: 12 Stepping: 3 with MMX, SSE whole, SSE FP

  Built-in memory: 15, 8GB

  Free memory: 4, 9 GB

  I found the reason, but there is no solution...

  Comments:

  The double slash ' \ ' in the path appears to be introduced with the upgrade to PSE10. I can't say how it happened, but there were about 27,000 files connected by an access path "D:\pictures\\album\portrait\image_1.jpg".

  Fortunately, I worked with this database, as in fact all files could be catalogued, modified, opened with the editor. I checked from time to time for "Missing files" and none has been identified. After I discovered the problem during the conversion of catalogue Lr, I checked the display "File Location" and none of the files with the double slash are recognized as part of the catalog. I could import into the catalog of the "location of the folder" producing duplicates:

  'D:\pictures\\album\portrait\image_1.jpg '.

  'D:\pictures\album\portrait\image_1.jpg '.

  live happily next to each other.

  I could "move" the wrong file in the thumbnail view in its original, which corrects the incorrect path. But as my collection is well distributed on a large directory structure and there is no way to sort way "thumbnail" it would be a never-ending task.

  Here are the steps I took to fix the problem. It was not as simple as it sounds by

  now and took a lot of trial and error for weeks.

  1. I made a backup of the catalog PSE10 ("File-> backup catalog..") hard disk
  2. I have 'removed' photos from their original location, so that they could not be found (as I had a distinct data reader, I just removed the drive letter in the Windows Disk Management Console)
  3. I restored the backup PSE10 ("File-> Restore Catalog... "), choose 'new place' and placed in the root of a different drive. If you do not have a spare laptop drive, you can use the "subst q: ; I had hoped to keep the structure of the root, it is easier for the PSE10 to reconnect files later, but I can't confirm that it makes a difference.
  4. After restoring PSE10 complained (thankfully!) could not find any files (27,000) with double '-', so, unlike the situation at the beginning, I could now chose "file-> reconnect-> all missing files. He tried to find the files, but he could not find them in the area returned after searching for 5 minutes for the first file. Then I reconnected a file manually and restarted the process and after 1 h PSE10 had reconnected all files without any problems, and the images appeared as well in the 'file location' display.
  5. As I wanted my files in their original location, I "return" the files in their original location by moving them in the 'File location' view, which took another 3 hours.
  6. As I was not very confident with the whole process ensuring all files have actually been part of this process, I closed 10 PSE and "reinstalled" my original tree together file pictures of the "retired" location (step 2) after you delete the files moved PSE10.
  7. I grew up PSE10 and checked for missing files, everything was still connected.
  8. Finally I re-imported the tree of the original files 'reinstalled' together again to see if something is missed, but all files have been correctly identified as duplicates. The final step was to validate "File Location" view, where are the files appears in the tree structure tight.

  Then, I did what I wanted finally to update the catalogue of PSE10 to LR6 and it worked without any problems take images and metadata across.

  Fact.

  A plea to Adobe...

  I think it would be a great idea to publish catalogues different proprietary formats (PES / LR). This

  cannot be that difficult because you must have appropriate documentation. In this case the problem could be

  solved with double '-' setting programmatically. If you think that your customers entrust their digital

  assets on your cloud, some "opening" your end would be just one...