L2 switch selection

Similar Questions

• Help with niSwitch example of DMM switch Handshaking

  I have a bit of trouble getting my stint of PXI-2575 multiplexer and PXI-4071 DMM talking to each other.  "" They are located in a PXI-1045 chassis on which I am currently running the "niSwitch DMM Handshaking.vi switch ' example.

  At the moment all I'm doing is read in a DC using this example.

  SWITCH

  Topology: 2575/1fil 196 x 1 Mux

  List of Scan: ch0-> com;

  Trigger entry: front connector

  Advanced analysis of output: front connector

  DMM

  Type of measure: Volts DC

  [...]

  The destination full measure: external

  Source of relaxation: external

  Then try to run the VI, I get the following error:

  Possible reasons:
  Driver status: (Hex 0xBFFA6B9F) DAQmx 89120 error has occurred:
  Terminal of source routing is not found on the device.

  Make sure that the name of the terminal is valid for the specified device. See Measurement & Automation explore valid names of terminals.

  Property: DAQmx_DigEdge_AdvTrig_Src
  Property: DAQmx_DigEdge_AdvTrig_Edge
  Source device: PXI1Slot7
  Terminal of source: TrigIn

  Status code :-89120

  Of course, I'm new to this.  Help, please!

  Thank you.

  Hey Sean,

  Looks like we have a differential of 2 volts. We will use 2 wires 98 x 1 and the following connections:

  The help of switches:

  

  On this basis, we can see in the lower right that CH0 + is pin 1 and CH0 - pin 2.  We need to hang the signal of 2 volts at pin 1 and pin 2 land.

  We hang the DMM HI COM + (PIN NUMBER 173) and the DMM Lo-COM (PIN 174).

  Now all we have to do is open switch Soft blanks Panel ('start' programs' National Instruments' OR-Switch), select topology (98 x 1 2 son) and connect CH0 to Com.  If we take a DMM measure, we should now read 2 volts.

  Now that we have all this work, we will make it faster by using the example of transfer protocol you mentioned previously:

  Suppose we want to connect channel 0 to com, take a measure, then connect the way com 1, take a measure, and then connect track 2 com, etc. all the way up to channel 15 to com.  A scan list that performs this operation is: "ch0-> com; CH1-> com; CH2-> com; Ch3-> com; CH4-> com; CH5-> com; CH6-> com; CH7-> com; CH8-> com; CH9-> com; Ch10-> com; CH11-> com; Ch12-> com; ch13-> com; CH14-> com; CH15-> com; ».

  We can simplify this scan to help list of ':', the following: ch0:15-> com  This is equivalent to the same actions as above, but is much easier to watch.  I hope this is enough information to get started.  Let us know if you have any questions.  Have a great day!

• [Windows] Problem with the shortcut to activate directly between the selection and

  Hi all

  Sorry to ask such a silly question, but I have searched on the web for hours without finding the answer. So, I come to you guys, hoping you have the magic answer.

  My problem is that I have recently moved to Illustrator CS5 after using Illustrator 10 for a very long time. I use a lot the keyboard and the mouse to draw in Illustrator and a shortcut has been replaced and I can't find a new job.

  In the pen (or any other tool), mode I press Ctrl for quick selection tool, very handy. But I used to press Ctrl + Tab to switch between the direct selection tool selection tool and vice versa. In CS5, this shortcut has been replaced by switching between the various documents (which makes more sense) and the new command according to the help (ctrl + alt + tab) file does not work on Windows (Vista) as it switches between programs rather than selection tools. the only solution I have is manually selecting the desired tool, which interrupt the flow somehow...

  Can someone help me? Thank you very much

  Michael

  It's a solution, even if I don't know how to re - allocate such command (toggle selection). (Edit: actually, I found where it was possible: Edit-> keyboard shortcuts-> Menu commands-> other Select-> switch selection tools)

  I always have the feeling that there is a shortcut to this command. Even the help file adobe Web site and specify the command ctrl + alt + tab for windows, which is stupid because it is clearly in conflict with windows shortcuts.

  Any other idea?

• automatic script selects when I don't want what it

  me new sry if this script

  
  If (this.getField("race").value = 'Human') {}
  If (this.getField("gender").value = 'Male') {}
  var h_male = new Array ();
  h_male [0] = "bob";
  h_male [1] = "mathew";
  h_male [2] = "andrew."
  h_male [3] = 'stephen ';
  h_male [4] = "ben."

  
  var hm = math.floor (5 * Math.random ())

  this.getField("character_name").value = h_male [hm] ;}

  else (this.getField("race").value = 'Man')
  (this.getField("gender").value = 'Female'); {
  var h_female = new Array ();
  h_female [0] = "michelle";
  h_female [1] = "sarah."
  h_female [2] = 'skye ';
  h_female [3] = 'kayla ';
  h_female [4] = 'louise ';

  var RF = Math.floor (5 * Math.random ())

  this.getField("character_name").value = h_female [hf] ;}

  }

  now, it kind of works that im having the problem is that when I hit the random button it puts the male sex and selects random h_female not the h_male auto

  I could be wrong, but I think it's the (this.getField("gender").value = "Male") written in the kind of field instead of read? If yes how can I fix

  Post edited by: darka2011

  Do you get errors in the JavaScript console?

  I have a message about a missing code block terminator,"}".

  Once this is fixed, the following message is on the reference to "math" is not defined.

  Using the nested if:

  Array of random names
  aNames var = new Array();
  Clear the field
  Event.value = ";
  test for the race
  If (this.getField("race").value == 'Human') {}
  human chose
  test for the human race
  If (this.getField("gender").value == 'Male') {}
  human male
  complete male names
  aNames is ['bob', "mathew", "andrew", "stephen", "ben"];.
  Event.Value = aNames [Math.floor (aNames.length * Math.random ())];
  } Else if (this.getField("gender").value == 'Female') {}
  human female
  fill in names of frmale
  aNames = ["michelle", "sarah", "skye", "kayla", 'louise', 'Zelda'];
  Event.Value = aNames [Math.floor (aNames.length * Math.random ())];
  } else {}
  man not male or female
  Event.Value = "";
  end of human gender options
  }} else {}
  Event.value = ";
  } / / end of race options

  Using the switch statement:

  Array of random names
  aNames var = new Array();

  If (this.getField("race").value! = "" & this.getField("gender").value.) = "«) {}
  switch (1) {}

  case (this.getField("race").value is 'Human' & this.getField("gender").value is 'Male'):
  human male
  complete male names
  aNames is ['bob', "mathew", "andrew", "stephen", "ben"];.
  Event.Value = aNames [Math.floor (aNames.length * Math.random ())];
  break;

  case (this.getField("race").value is 'Human' & this.getField("gender").value is 'Female'):
  human female
  fill in names of frmale
  aNames is ["michelle", "sarah", "skye", "kayla", 'louise', 'zelda'];.
  Event.Value = aNames [Math.floor (aNames.length * Math.random ())];
  break;

  by default:
  for all elements not matched
  App.Alert ('no match');
  break;
  } / / end of switch selections
  } else {}
  Event.value = ";
  } / / end if the race and gender not empty

• How can I cancel an ad block?

  I used ad block to block an annoying ad in an email from PayPal. It resulted in my entire page of blocked e-mail messages. I can connect to my e-mail account but cannot access my messages. How can I cancel my block?

  My computer is Microsoft Vista and Firefox is my browser.

  (So that I can receive answers, I provided an alternate email address in registering this Firefox Support Account)
  

  Another approach - your custom filters are visible/editable.

  1. Click on the ABP icon, choose Filter Preferences
  2. Click custom filters, then on the Exceptions line, click action and choose Show/Hide filters (it's a market switch selection). The pane to divide and show your custom filters on the right side of the pane.
  3. If you can identify one of the problems, right-click on it and choose delete OR click the checkbox for this line in the enabled column to uncheck it leaves in place, but the filter will not be applied as long as it is not checked.

• Toshiba 37RV733F starts in radio mode

  Hello

  I have a Toshiba 37RV733F. Over the last year, he started to behave more and more eccentric.
  Almost every time that I start the TV, it starts in mode radio (RADIO of DTV) - although I've never used this feature (by free will, that is).

  Solution?

  Of course, this is rather annoying.
  I tried to reset the TV without success. And the software is updated as well.

  Thanks in advance!

  Hello

  If TV don't past not automatically, use the entry switch selection window choose the right input (DTV TV, Radio of DTV, DTV text)
  To start the entry switch selection window you must press the Enter key (arrow and circle) on the remote control. Then you should be able to choose between the DTV TV, Radio DTV DTV text

• No Power Manager on T450s shortcut key?

  I installed a X 220 to a T450s, and I see that there is no shortcut key to select a profile for more power. This seems like a huge oversight. Windows 7 only allows its profiles of power native to be learned from its quick access tools (battery icon in the tray of the taskbar or menu of the Windows key + X). Now if I want to use one of the Lenovo power profiles (which are much more customizable than the native Windows ones), I have to make visible the toolbar of the Lenovo Power Manager in my taskbar so you can double-click it and wait for the application of Power Manager to launch. So I can select a profile, 'apply' the selection and close the application.

  I'm used to switching several times power profiles per day depending on whether I use the laptop on battery on my couch, use it to compile the code on AC power at work, or the half dozen of other situations. Is it possible to install the old app hot-switch selection of profiles of power on this machine and map a keyboard shortcut to this? (I'd be happy to give up some of the unnecessary shortcut keys such as "OS Search" (F10) and 'Switch Window' (F11).

  The executable power profile switcher is C:\Program Files (x 86) \ThinkPad\Utilities\PWMOSDV. EXE.

  PIN in your taskbar or assign a hotkey (for example with AutoHotkey).

• power supply upgrade compaq presario sr511onx

  I have a compaq presario sr511onx I need to know what kind of power supply my pc takes. I need to know if its a box atx or micro atx case.

  This will help.

  Part number 5188-2622 250 watts (max) (Zinfandel) power supply, Bestec ATX-250-12V)-100-120VAC and 200-240VAC input (switch selectable), 50/60 Hz

  SEE:

  http://support.HP.com/us-en/document/c01355925

  Message edited by dmhoo29 on 02/05/2009 18:32

• connection intermittent cRIO (with MAX, etc.)

  Our cRIO connects to our fine PC when it is initialized at first - and you can view it fine in MAX, Manager of distributed system and its web interface. But after all 3-5 minutes it always loses connection. It remains disconnected, and only restart the cRIO restores the connection but only for another 3-5 minutes. Only MAX restart does not help. We can ping the cRIO ok when 'disconnected' - which, to me, implies that it is a problem of higher level software.

  We had this particular cRIO work fine before.

  Thanks for your suggestions... While not in a rush to do this, I really want to understand why the connection is intermittent

  Here are some details:

  • MAX version 5.0.0f1
  • LV2011 DS2
  • cRIO is a 9022 (no screws running on it to the commissioning, CPU minimum load - idle = 97%)
  • computer development is a Vista Home Premium 32 bit
  • connected together using the brand-new Cat5E cable
  • TCP/IP settings on the laptop - Static IP, IP 192.168.2.4 address, mask 255.255.255.0
  • TCP/IP settings on cRIO - Static IP, the IP 192.168.2.1, mask 255.255.255.0 (gateway and DNS are blank or 0.0.0.0)
  • cRIO set to use for the link speed autonegotiation (no option to change this) and detection of packets = "interrupt".
  • PC value link autonegotiation speed, but has no effect on the problem, if it is set on a fixed, low speed for example. Half-Duplex 10 Mbps
  • PC Firewall is configured to allow the port 3580, and actually disable the firewall altogether change the problem

  Had the chance to try again with my intermittent connection to cRIO, and here's what I found:

  • Connection through a switch, rather than directly with crossover cable - made no difference, still kept disconnecting after 3-4 minutes
  • With no other network on my laptop other than the LAN - no difference development
  • cRIO with APP No. dip switch select IT - no difference
  • cRIO with game of dip-switch SAFE MODE - this time it is remained connected, but this mode is not very useful as a solution

  Then I was reinstalling the software cRIO as suggested - it did not complete the first time, but second attempt was beautiful and connection is now very stable (and has not abandoned in the last 30 minutes).

  Here are the instructions to reinstall (just in case useful for others):

  1. In the measurement and Automation Explorer (MAX), access remote systems | cRIO | Software
  2. Click on the "Add/Remove software", and an installation wizard will appear
  3. With currently installed version of the selected software - "then click to reinstall the software currently installed.
  4. Follow the rest of the instructions, and it should take about 4-5 minutes

  Thanks for your help

  Andy

• Attempts to installation of Windows 7 Service Pack (x 64) leads to "Bluetooth Stack Server" "AppCrash": no wireless connectivity possible!

  I realize that my question is about the hardware and drivers that are not Microsoft, but all the trouble seems to begin with the fact that the latest version of Windows Update attempts.

  I have reset the settings of update on "Automatic" after missing the guests of installation, leading to several attempts installation of Windows 7 Service Pak for x 64-based systems.

  On installation/configuration logoff never surpassed ~ 10% during "installation failed, returning from changes" message appeared before the shutdown.

  On reboot, the error message: "Bluetooth Stack server has stopped working", problem report Details indicate: "AppCrash".

  Today, for the first time in ~ a year, brought my HP Probook 4530 s to a reliable wifi hotspot 2011: "no public network detected" appeared, everyone had no problem.

  The "centre mobility Windows", which usually has a box indicating the status of LAN wireless, had this box is completely missing.

  Check the two Bluetooth and Realtek PCIe GBE Family Controller (devices used for internet connectivity?) indicate that "the drivers are up to date" and "this device works correctly.

  I am running Windows Security Essentials and Malwarebytes AntiMalware.  Also recently installed the free version of SpyBot, run a daily scan.

  I've never really had any problem/detection of serious virus/malware that I'm aware of.  Windows 7 has been well up to this point.

  Also tried a system restore to BEFORE the Service Pack update attempt: it had no effect on the detection of wireless connectivity or a connection.

  If anyone can describe a troubleshooting chart that might allow me to again connect to a wifi hotspot, I would be very grateful.  Thank you.

  I should finally a solution to my inability to access a local signal of the WiFi for my laptop.

  As stated in my first post of the question, the problem started after a sudden error message "Bluetooth Stack Server."

  All the remedies, I've tried are listed above.

  This HP laptop came with a general diagnosis called HP Support Assistance program.

  Recently, I downloaded a new version of this program.

  For the first time, an icon appears in the taskbar for the "HP Connection Manager", which indicates the activation state of all wireless and Bluetooth devices.

  The following State scored to WiFi (Wireless LAN): "disabled in BIOS F10.

  Since I was able to connect to a WLAN before the Bluetooth Stack Server error, this setting IS ENABLED: it was not "manually" disabled.

  I entered the system BIOS via F10 during boot and the following path:

  "System configuration" > "Integrated device Options" > "LAN/WLAN SWITCHING" > select 'ON'.

  Rebooted the laptop normally, a check for HP Connection Manager "indicated"enabled"for the wireless LAN setting, and"Windows Mobility Center"was now a visible box for WLAN/LAN status."

  I don't know how or why the BIOS for this parameter settings were off.

  Please mark this issue as resolved, with this post as the answer.  Thanks for your suggestions.

• ListField and navigationclick

  Hello

  I read this tutorial

  http://www.BlackBerry.com/knowledgecenterpublic/livelink.exe/fetch/2000/348583/800332/800505/800345/...

  to create a list of items on the messaging screen.

  Now, I like, when I select an item from the list, open a new screen to view other information.

  How can I do?

  In the development guide it is only written to use navigationclick, but I don't understand where to use it

  Thank you

  I tried this solution and it works:

     protected boolean navigationClick(int status, int time)
     {
         Field field = this.getFieldWithFocus();
  
         if(field instanceof ListField)
         {
  
             int selected = _listField.getSelectedIndex();
             switch (selected) {
          case 0:
              pushScreen(new Screen1());
              break;
          case 1:
              pushScreen(new Screen2());
              break;
          case 2:
              pushScreen(new Screen3());
              break;
          case 3:
              pushScreen(new Screen4());
              break;
          case 4:
              pushScreen(new Screen5());
              break;
          default:
              break;
          }
            return true;
          }
  
         return super.navigationClick(status, time);
     }
  
    }
  

• How to call an existing application in the menu of an another aplication

  How to call an application in the menu select an another application example in the menu objects switch (selected) {case 0: here the call to other applications aexisting? break;}

  You can create a MenuItem that executes the code in this article.

  How - to launch a third-party app to another third-party application
  Article number: DB-00455

  http://www.BlackBerry.com/knowledgecenterpublic/livelink.exe/fetch/2000/348583/800332/800620/How_To _...

• HP470

  Hello
  A year ago I upgraded from my laptop H450 to a H470 I bought used and worked on my cable usb very well. I only use this little laptop when travel / on the road for instant printing of photos for the most part.
  I have several other HP and Canon printers to suit the varied when needs home.
  I thought to try this H470 on bluetooth. Beat Cableusb shuffling around the room.

  I bought a wifi for the H450 adapter and it worked fine if I use at home but terrible for the installer when you say in a hotel on the road!

  I don't know how to use bluetooth on the device. I'm pretty sure that is not based. Device watch model number of front door inkcover like HP Officejet H470 does not say anywhere the WBT. At the back of the camera next to the battery is 3 way switch selection of shows from 1 to 2 and 3 being bluetooth. I asked my laptop looking for Wifi signal with the value #3 and no signal. Card only on the unit slot says is for MMC and SD/MiniSD (I don't know what is a MMC console) if I buy a bluetooth adaptor it inserts into the SD card slot?
  I hope that if then when on my most recent (1 year old Sony camera with Windows 7 should be able to find and load the bluetooth printer?
  Any help always also appreciated!

  Hi DrowningInTech,

  See the following document below.

  http://support.HP.com/us-en/document/c01183542

  What is the model number of this H470?

• ESXi 5 - How to monitor NETWORK traffic

  Hi all

  I have 4 network cards on my server and I added a quad-port PCI NIC

  I use 4 network cards are associated with associations using native ESX for management and vMotion

  While the other 4 are for my ISCSI traffic. ESXi native mulipathing

  How to see if the traffic is through the network/switchports cards and all paths?

  Thank you

  In the vSphere client, select the host, and then click the performance tab.  Click Advanced, and in the drop-down list 'Switch' select network.   You can click Chart Options to select specific performance parameters to display.

  If you're connected directly to your ESXi host, then simply select the Performance tab for the host.  The "Advanced" is the only option when it connects only not via vCenter Server. ""

• Behavior of pen tool that I find a bit odd

  I don't know if it's something that you can change or just the way things are.

  you draw a path and you have the black arrow as your modifier [ctrl], but you want the white arrow, if you switch to it, then go back to the pen and wear on the drawing. but the pen wants to start a new path because you change tools. or you want to turn on or off smart guides half way, same case. This seems a bit out of me, so I wonder if there is something I have not adjusted. the pen tool in PS does not appear you the spirit of switching selection tools: as long as you were on the path is unhindered, he picks up the anchor, it stopped.

  It's just the way it is. Too-many-separate-tools of the Illustrator design often prevent behaviors which are taken for granted in programs with more elegant design interfaces.

  JET