L2l configuration with internet access
Hi all
I put to the top and L2L vpn between my host site and a small office of two people using my asa 5510 and a bit of netgear vpn router. I wish to have to come to the headquarters for the internet users. I can access all the resources and others, but the internet does not work on the site. I made sure I got the permit for same-security-traffic intra-interface command on my asa. Maybe I'm missing a route? Can someone point me in the right direction?
TIA,
R
Yes...
Global 1 XXX1 (outside)
Global x.x.x.2 10 (outside)
Global x.x.x.3 20 (outside)
NAT (inside) 1 192.168.1.0 255.255.255.0
NAT (inside) 10 192.168.10.0 255.255.255.0
NAT (outside) 20 192.168.20.0 255.255.255.0
Tags: Cisco Security
Similar Questions
-
Need help with internet access on a Linksys E1200 strategy
Hi, I have an a Linksys E1200 (Firmware Version: 2.0.01), and September 13, 2012, I configured the Internet access policy to deny access to internet for 4 devices between the hours of 22:00 and 08:00 on the evening of the school.) It was working fine! I was very pleased.
Over the last weekend, the electricity was launched for a second, the power was back on in 2-3 seconds if. The router comes back online, and everything seemed in excellent working condition. Then Sunday evening (considered to be a night of school in our House) at 22:00 the router did not refuse Internet 4 devices as it normally did. I logged into the control panel admin via a browser web, and checked access to internet strategies, I configured last week was still configuration property.
Everything was always configuration property to deny access to the internet for 4 devices Sunday night/Monday morning between 08:00 and 22:00. I checked that the router has the date and time. But the router is not always deny access as it was setup to do. It worked fine before the weekend, and then after the weekend it stopped working the property. The only thing I can think of this month of may of the cause is 2-3 seconds, the power went out then came back on. The router is connected through a surge protection.
Then I set up the Internt access policy week last to deny access to 4 devices on the night of the school between 22:00 and 08:00. I waited 24 hours to make sure it worked, after that it worked, I got the router send me a backup of the config file. I tried to use it to solve this problem, but it did not help either.
This is a screenshot of what looks like my Internet access policy. I had to create 2 policies because the router has refused to create a policy where the end time was not later than the start time. Anywho, so political #1 is from 22:00 to 11:55, and policy #2 is from 12: 00 to 08:00. This Internet access policy is configured to deny access to 4 devices between midnight and 08:00 Monday morning. It was working fine last week, so I'm 100% positive that it is the router.
The following screenshot is the status information to show the date and time of the router is correct.
So the router was Monday morning @ 03:00, the router has an active policy of internet access to deny the device access to the internet, the router had recently worked flawlessly to do this, but for some reason any, that he could not do this morning?
Can you please explain it to me or provide me with free software to "lock" the internet for specified devices. I really want to have to stay until 22:00 5 nights a week, so I can help my daughter sneaking online when she should be in bed. taking his phone and the laptop is not an option.
Thanks for reading, forward a reply as soon as possible.
~ Tony
Hello. I think that Yes, too, that it is a router problem. Just to isolate it, try to update the firmware and then reset and reconfigure the router again and use the same policies that have worked before. On Cisco's Web site, the latest firmware for version 2 is 2.0.04. You can download it here http://homesupport.cisco.com/en-us/support/routers/E1200. You can use the links below in the public KB site of Cisco.
Manually upgrading firmware of the Linksys wireless-N Router
Setting up a Linksys router for DSL Internet connection
http://www6.nohold.NET/Cisco2/UKP.aspx?pid=80&VW=1&articleid=3687
Setting up a Linksys router with cable Internet service
http://www6.nohold.NET/Cisco2/UKP.aspx?pid=80&VW=1&articleid=3686
-
Private network with Internet access
Hello
Using WS 9. Building a 'private' isolated network who always has Internet access for testing purposes? I built a virtual machine that has AD, DNS and DHCP installed. Ask yourself if it's feasible to isolate this virtual machine from the corporate LAN, but allow it to have access to the Internet to d/load patches/security fixes?
I created "the" private network as follows (VMnet2):
Thank you
BRITISH COLUMBIA
Host-only, it's just that and does not communicate beyond the host. You could add a connected by a bridge or a NAT Network Adapter to the Virtual Machine and connect it to your updates and unplug when done.
-
Cannot access internet when you configure with internet connection sharing.
INTERNET HELP?
I tried to use the internet connection to my wireless on my PC laptop not wireless using an Ethernet cable. I have connected my pc not wireless to my laptop wireless pc with ethernet cable, I did everything as requested on the site of "Dummies" and the PC says its connected but when I try to go on Internet Explorer, it does not work? HELP! : (PS) my PC is Windows Vista and my laptop Windows 7Hello
1. While sharing was the Internet works fine before?
2 did you change on your computers before this problem?I suggest you follow these methods and check.
Method 1: You can follow the Windows Help article below and check that ICS is set up correctly.
Set up a shared Internet connection using ICS (Internet Connection Sharing)
http://Windows.Microsoft.com/en-us/Windows7/set-up-a-shared-Internet-connection-using-ICS-Internet-connection-sharing
If ICS is not configured correctly, then you must post back the result by running the following command
To do this:
a. click the Start button.
b. type cmd in the search box.
(c) in the command prompt, you must type ' ipconfig/all' and check the result.Take a screenshot of the command prompt and post.
To take a screenshot, you can follow this link below.
Use capture tool to capture screenshots
http://Windows.Microsoft.com/en-us/Windows-Vista/use-Snipping-Tool-to-capture-screen-shotsMethod 2: Windows wireless and wired network connection problems
http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows?T1=Tab03I hope this helps.
Thank you.
-
Virtual MACHINE on Windows 7 with internet access
Hello world
I have an iso of Debian Linux to create a virtual machine at this address: http://ftp.nl.debian.org/debian/dists/squeeze/main/installer-i386/current/images/netboot/
This image needs to download packages from the internet, but I don't know why I can't have access to the web. I'm in a corporate network with a proxy, but I already tried together the proxy during installation and it still does not work.
I'm using VMWare workstation 6.5, and I wonder if this is a missing configuration on the VMware or Windows 7. I also tried to connect to internet other virtual machines to Linux that I've already created (an older Debian and Ubuntu), but none of them could not access the internet (even if the proxy server).
Could you help me on this?
Thanks in advance,
Have you tried to bridge? I seem to have better luck with this setting.
-
Problem with Internet access: local only for wireless in Vista
Help, please. I have a Dell laptop and a Dell desktop computer. The other day, I pressed WPS on my router Netgear wireless, and since then, my desktop computer (Windows Vista Home Premium SP2) was not able to connect to the Internet. The office is connected to my router. My Dell (Win 7 Pro) laptop is able to connect wirelessly to the router and Internet.
That's what I tried:(1) I bought a new wireless router Netgear WNDR4500(2) I bought a cutting mini USB wifi adapter for the desktop. Install the driver.(3) reset winsock, ipv4, ipv6, dns-netsh int ip reset reset.log-netsh winsock reset catalogipconfig/flushdns(4) order McAfee firewall(5) restarted several times(6) persons with disabilities wired and wireless enabled - I get signal green/fort(7) off active and wired wirelessNone of the above seem to work. I keep getting 'Access to local only' on both cables and wireless. When I ping yahoo.com, I get no response.My laptop, however, works very well in the connection to the wireless router and also to the Internet.Anything else I can try? Help, please!KTHello
Thanks for sharing the information valid.
In case, if you need help, you can always post your questions as well as your valuable suggestions in this forum.
-
Problems with internet access, troubleshooting, Windows 7 does not work.
Hello, I have recently started up to Windows 7 on a partition of Windows 10, because a game wasn't working properly on Windows 10 system (has notified downgrade after a one hour session troubleshooting).
I don't know if the game is causing these issues or anything else, but my internet connection goes away, even if the internet bar shows that it has internet.
Right now, I'm typing this, it says I have a problem.
Also, I have troubleshooted a lot of times, with the answer is:
This happens at random, or whenever I join a game for Minecraft.
Does anyone know the solution to this problem?
Other images:
Hello
You can see the answer given by Arya S Asok by mentioning the problem with adapter or wireless access point
Let us know how it goes.
Kind regards
-
Problem with internet access point
Hello, I saw that this question was asked before, but has never seen a solution to my problem, I will explain:
I have like 5 months with this problem. I have a TP-LINK 300Mbps Wireless N Router, model No. TL-WR841ND. The fact is that when I plug in my router to the Modem, my wireless network seems to work fine, but when I try to connect to my computer or any other device to the network (mobile phones, playstation 3, tablets, etc.), I am unable to do so. On my laptop, I get the message: 'Problem with wireless adapter or access point', but the most confusing thing is that sometimes I can connect to the Internet via my network wireless without any problem.
This time I decided to post my problem, because I'm tired of it. Sometimes it happens, sometimes it doesn't. Right now, I have two days without Internet connection (Via router), because my modem works properly.
PS: I have another router (Linksys) and I can connect to this network, but I want to solve my problem with the TP-Link because the signal is stronger. Help!
See links.
How to install a TP-LINK wireless routers (Recommended)?
http://www.TP-link.com/LK/article/?faqid=92
Why can I not access the Internet after connecting the TP-LINK router to my modem.
http://www.TP-link.com/LK/article/?faqid=138
TP-Link FAQ.
-
L2L configuration with the same intellectual property regime
Hi all
hoefully it won't be easy. I set up some VPN site to site, but now I have one that has a plan of the same IP as me. 192.168.9.x is the subnet in question. I think I'll need to NAT, the jobs of 192.168.9.x who will have access to my network. I usually add a rule exempt from NAT for my other L2L sites, but since I'm on NAT for this one I can not add, correct? Also, I think that when I add a route statement to my router I point to the NAT address... Thanks in advance for any help.
Please visit the following OCC configuration guides...
-
Help I have something overlooking simple went through all the stages of preparation for machines as well as differences in networking. He had twice right, but when the internet connection is broken (my blackberry), something is not right on reconnect.
Are you asking how to enable Internet connection sharing on the host of Vista? If so:
- Go to Control Panel > network and sharing Center .
- Click manage network connections .
- Right click on the USB connection.
- Click on Properties .
- Click sharing .
- Put a checkmark in the Internet connection sharing box.
-
Cannot get my Satellite Pro to work with internet access wireless
I have a Satellite Pro L20 - who has wireless network adapter. Bought a BT Voyager 2110 Wireless ADSL router. Connected to my broadband router. Used Toshiba config to find router on my laptop - it looks like I have then drag the icon of the laptop to the router but it says I can't do because the router is used by another owner?
Should I do anyting - Inter adapter card in my laptop says activated - the router is connected - but nothing works.
Please help but I'm pretty useless on these things so keep it clear
Thank youHello
Is this the result even when you use the settings Windows wireless?
-
See above
· This is the Forum for Windows Update .
For questions of Windows 7, here is a link to a list of the Windows 7 Forums:
http://social.answers.Microsoft.com/forums/en-us/w7network/threads
Windows 7 Networking Forum at the link above.
http://social.answers.Microsoft.com/forums/en-us/category/Windows7
Link above is Windows 7 forum for questions on windows 7.
All Windows 7 issues (other than Windows 7 update issues) should be directed to the it.
See you soon.
Mick Murphy - Microsoft partner
-
Activate Adobe on a will not connect to the computer with internet access
How to activate Adobe on a standalone computer?
This is the forum Adobe Reader that doesn't require activation. If you let us know what you are trying to activate, we can send you in the right direction.
-
Equium A100 - 027 PSAAQ - having problems with WiFi Internet access
Just installed Windows XP Home edition on my Equium A100-027 (PSAAQ) Vista didn't like. Now I'm having problems with Internet access. Should what drivers I download and how to install?
Thank you.
Hello
I suggest you to check the site toshiba driver
-> http://eu.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jspYou can search your machine and download the wlan drivers. If you don t know that you you just all download and install ´em, one of the drivers SHOULD work. ;)
Welcome them
-
Windows - Internet access, no split Tunnel L2TP VPN Clients does not
Greetings!
I have four ASA 5505 that I configured with 4 site to site VPN tunnels (works perfectly) to connect to our company facilities 4. The ASA is also configured with remote access L2TP/IPsec so that a specific group of users of portable computers can connect to and access to all facilities. It also works very well except for one important exception - my split tunnel setting doesn't seem to work, because I can't connect to the Internet outside the VPN resources.
I accept the inherent risk of allowing tunnels to split from a security point of view since I take the necessary steps to secure the systems used for remote access. I would appreciate any feedback on how to get the job of split tunnel.
Here is the configuration:
: Saved
:
ASA Version 1.0000 11
!
SGC hostname
domain somewhere.com
names of
COMMENTS COMMENTS LAN 192.168.2.0 name description
name 75.185.129.13 description of SGC - external INTERNAL ASA
name 172.22.0.0 description of SITE1-LAN Ohio management network
description of SITE2-LAN name 172.23.0.0 Lake Club Network
name 172.24.0.0 description of training3-LAN network Southwood
description of training3 - ASA 123.234.8.124 ASA Southwoods name
INTERNAL name 192.168.10.0 network Local INTERNAL description
description of name 192.168.11.0 INTERNAL - VPN VPN INTERNAL Clients
description of Apollo name 192.168.10.4 INTERNAL domain controller
description of DHD name 192.168.10.2 Access Point #1
description of GDO name 192.168.10.3 Access Point #2
description of Odyssey name 192.168.10.5 INTERNAL Test Server
CMS internal description INTERNAL ASA name 192.168.10.1
name 123.234.8.60 description of SITE1 - ASA ASA management Ohio
description of SITE2 - ASA 123.234.8.189 Lake Club ASA name
description of training3-VOICE name Southwood Voice Network 10.1.0.0
name 172.25.0.0 description of training3-WIFI wireless Southwood
!
interface Vlan1
nameif outside
security-level 0
IP address dhcp setroute
!
interface Vlan2
nameif INSIDE
security-level 100
255.255.255.0 SGC-internal IP address
!
interface Vlan3
nameif COMMENTS
security-level 50
IP 192.168.2.1 255.255.255.0
!
interface Ethernet0/0
Time Warner Cable description
!
interface Ethernet0/1
switchport access vlan 2
switchport trunk allowed vlan 2-3
switchport vlan trunk native 2
switchport mode trunk
!
interface Ethernet0/2
switchport access vlan 2
switchport trunk allowed vlan 2-3
switchport vlan trunk native 2
switchport mode trunk
!
interface Ethernet0/3
switchport access vlan 2
switchport trunk allowed vlan 2-3
switchport vlan trunk native 2
switchport mode trunk
!
interface Ethernet0/4
switchport access vlan 2
switchport trunk allowed vlan 2-3
switchport vlan trunk native 2
switchport mode trunk
!
interface Ethernet0/5
switchport access vlan 2
switchport trunk allowed vlan 2-3
switchport vlan trunk native 2
switchport mode trunk
!
interface Ethernet0/6
Description for Wireless AP Trunk Port
switchport access vlan 2
switchport trunk allowed vlan 2-3
switchport vlan trunk native 2
switchport mode trunk
!
interface Ethernet0/7
Description for Wireless AP Trunk Port
switchport access vlan 2
switchport trunk allowed vlan 2-3
switchport vlan trunk native 2
switchport mode trunk
!
boot system Disk0: / asa821-11 - k8.bin
Disk0: / config.txt boot configuration
passive FTP mode
clock timezone IS - 5
clock to summer time EDT recurring
DNS domain-lookup outside
INTERNAL DNS domain-lookup
DNS domain-lookup GUEST
DNS server-group DefaultDNS
Name-Server 4.2.2.2
domain somewhere.com
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
DM_INLINE_TCP_1 tcp service object-group
EQ port 3389 object
port-object eq www
EQ object of the https port
EQ smtp port object
the DM_INLINE_NETWORK_1 object-group network
network-object SITE1-LAN 255.255.0.0
network-object SITE2-LAN 255.255.0.0
network-object training3-LAN 255.255.0.0
object-group training3-GLOBAL network
Southwood description Global Network
network-object training3-LAN 255.255.0.0
network-object training3-VOICE 255.255.0.0
network-object training3-WIFI 255.255.0.0
DM_INLINE_TCP_2 tcp service object-group
EQ port 5900 object
EQ object Port 5901
object-group network INTERNAL GLOBAL
Description Global INTERNAL Network
network-object INTERNAL 255.255.255.0
network-object INTERNALLY-VPN 255.255.255.0
access-list outside_access note Pings allow
outside_access list extended access permit icmp any CMS-external host
access-list outside_access note that VNC for Camille
outside_access list extended access permit tcp any host CMS-external object-group DM_INLINE_TCP_2
access-list outside_access note INTERNAL Services
outside_access list extended access permit tcp any host CMS-external object-group DM_INLINE_TCP_1
DefaultRAGroup_splitTunnelAcl list standard access allowed INTERNAL 255.255.255.0
access-list sheep extended ip INTERNAL 255.255.255.0 allow INTERNAL VPN 255.255.255.0
access-list extended sheep allowed ip IN-HOUSE-GLOBAL SITE1-LAN 255.255.0.0 object-group
access-list extended sheep allowed ip IN-HOUSE-GLOBAL SITE2-LAN 255.255.0.0 object-group
access-list extended sheep allowed ip object-IN-HOUSE-GLOBAL object group training3-GLOBAL
access-list INTERNAL-to-SITE1 extended permit ip IN-HOUSE-GLOBAL SITE1-LAN 255.255.0.0 object-group
access-list INTERNAL-to-training3 extended permitted ip object-IN-HOUSE-GLOBAL object group training3-GLOBAL
access-list INTERNAL-to-SITE2 extended permit ip IN-HOUSE-GLOBAL SITE2-LAN 255.255.0.0 object-group
no pager
Enable logging
exploitation forest asdm warnings
Debugging trace record
Outside 1500 MTU
MTU 1500 INTERNAL
MTU 1500 COMMENTS
192.168.11.1 mask - local 192.168.11.25 pool IN-HOUSE VPN IP 255.255.255.0
no failover
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 623.bin
enable ASDM history
ARP timeout 14400
Global 1 interface (outside)
(INTERNAL) NAT 0 access-list sheep
NAT (INTERNAL) 1 0.0.0.0 0.0.0.0
NAT (GUEST) 1 0.0.0.0 0.0.0.0
5900 5900 Camille netmask 255.255.255.255 interface static tcp (GUEST, outdoor)
3389 3389 Apollo netmask 255.255.255.255 interface static tcp (INDOOR, outdoor)
public static tcp (INDOOR, outdoor) interface www Apollo www netmask 255.255.255.255
public static tcp (INDOOR, outdoor) interface https Apollo https netmask 255.255.255.255
public static tcp (INDOOR, outdoor) interface smtp smtp Apollo netmask 255.255.255.255
5901 puppy 5901 netmask 255.255.255.255 interface static tcp (GUEST, outdoor)
Access-group outside_access in interface outside
Timeout xlate 0:05:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
RADIUS protocol AAA-server Apollo
Apollo (INTERNAL) AAA-server Apollo
Timeout 5
key *.
AAA authentication enable LOCAL console
the ssh LOCAL console AAA authentication
AAA authentication LOCAL telnet console
AAA authentication http LOCAL console
Enable http server
http 0.0.0.0 0.0.0.0 INTERNAL
http 0.0.0.0 0.0.0.0 COMMENTS
No snmp server location
No snmp Server contact
Community SNMP-server
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set esp-3des esp-sha-hmac TRANS_ESP_3DES_SHA
Crypto ipsec transform-set transit mode TRANS_ESP_3DES_SHA
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
SYSTEM_DEFAULT_CRYPTO_MAP game 65535 dynamic-map crypto transform-set ESP-3DES-SHA TRANS_ESP_3DES_SHA
correspondence address 1 card crypto outside_map INTERNAL SITE1
card crypto outside_map 1 set of peer SITE1 - ASA
card crypto outside_map 1 set of transformation-ESP-3DES-SHA
address for correspondence card crypto outside_map 2 INTERNAL training3
outside_map 2 peer training3 - ASA crypto card game
card crypto outside_map 2 game of transformation-ESP-3DES-SHA
address for correspondence outside_map 3 card crypto INTERNAL SITE2
game card crypto outside_map 3 peers SITE2 - ASA
card crypto outside_map 3 game of transformation-ESP-3DES-SHA
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
delimiter group @.
Telnet training3 - ASA 255.255.255.255 outside
Telnet SITE2 - ASA 255.255.255.255 outside
Telnet SITE1 - ASA 255.255.255.255 outside
Telnet 0.0.0.0 0.0.0.0 INTERNAL
Telnet 0.0.0.0 0.0.0.0 COMMENTS
Telnet timeout 60
SSH enable ibou
SSH training3 - ASA 255.255.255.255 outside
SSH SITE2 - ASA 255.255.255.255 outside
SSH SITE1 - ASA 255.255.255.255 outside
SSH 0.0.0.0 0.0.0.0 INTERNAL
SSH 0.0.0.0 0.0.0.0 COMMENTS
SSH timeout 60
Console timeout 0
access to the INTERNAL administration
Hello to tunnel L2TP 100
interface ID client DHCP-client to the outside
dhcpd dns 4.2.2.1 4.2.2.2
dhcpd ping_timeout 750
dhcpd outside auto_config
!
address INTERNAL 192.168.10.100 dhcpd - 192.168.10.200
dhcpd Apollo Odyssey interface INTERNAL dns
dhcpd somewhere.com domain INTERNAL interface
interface of dhcpd option 150 ip 10.1.1.40 INTERNAL
enable dhcpd INTERNAL
!
dhcpd address 192.168.2.100 - 192.168.2.200 COMMENTS
dhcpd dns 4.2.2.1 4.2.2.2 interface COMMENTS
enable dhcpd COMMENTS
!a basic threat threat detection
statistical threat detection port
Statistical threat detection Protocol
Statistics-list of access threat detection
a statistical threat detection tcp-interception rate-interval 30 burst-400-rate average rate 200
NTP server 192.43.244.18 prefer external source
WebVPN
allow outside
CSD image disk0:/securedesktop-asa-3.4.2048.pkg
SVC disk0:/sslclient-win-1.1.4.179.pkg 1 image
SVC disk0:/anyconnect-win-2.4.1012-k9.pkg 2 image
enable SVC
Group Policy DefaultRAGroup INTERNAL
attributes of Group Policy DefaultRAGroup
Server DNS 192.168.10.4 value
Protocol-tunnel-VPN l2tp ipsec
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list DefaultRAGroup_splitTunnelAcl
value by default-domain somewhere.com
Group Policy DefaultWEBVPNGroup INTERNAL
attributes of Group Policy DefaultWEBVPNGroup
VPN-tunnel-Protocol webvpn
Group Policy DefaultL2LGroup INTERNAL
attributes of Group Policy DefaultL2LGroup
Protocol-tunnel-VPN IPSec l2tp ipsec
Group Policy DefaultACVPNGroup INTERNAL
attributes of Group Policy DefaultACVPNGroup
VPN-tunnel-Protocol svc
attributes of Group Policy DfltGrpPolicy
value of 192.168.10.4 DNS Server 4.2.2.2
VPN - 25 simultaneous connections
VPN-idle-timeout no
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list DefaultRAGroup_splitTunnelAcl
value by default-domain somewhere.com
the value INTERNAL VPN address pools
chip-removal-disconnect disable card
WebVPN
SVC keepalive no
client of dpd-interval SVC no
dpd-interval SVC bridge no
value of customization DfltCustomization
attributes global-tunnel-group DefaultRAGroup
VPN INTERNAL address pool
Group Policy - by default-DefaultRAGroup
IPSec-attributes tunnel-group DefaultRAGroup
pre-shared-key *.
Disable ISAKMP keepalive
tunnel-group DefaultRAGroup ppp-attributes
No chap authentication
no authentication ms-chap-v1
ms-chap-v2 authentication
attributes global-tunnel-group DefaultWEBVPNGroup
VPN INTERNAL address pool
Group Policy - by default-DefaultWEBVPNGroup
tunnel-group 123.234.8.60 type ipsec-l2l
IPSec-attributes tunnel-group 123.234.8.60
pre-shared-key *.
tunnel-group 123.234.8.124 type ipsec-l2l
IPSec-attributes tunnel-group 123.234.8.124
pre-shared-key *.
tunnel-group 123.234.8.189 type ipsec-l2l
IPSec-attributes tunnel-group 123.234.8.189
pre-shared-key *.
type tunnel-group DefaultACVPNGroup remote access
attributes global-tunnel-group DefaultACVPNGroup
VPN INTERNAL address pool
Group Policy - by default-DefaultACVPNGroup
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the netbios
inspect the rsh
inspect the rtsp
inspect the skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect the sip
inspect xdmcp
inspect the http
inspect the they
!
global service-policy global_policy
context of prompt hostname
Cryptochecksum:423c807c0d63cb3e9aeceda977053f84
: end
ASDM image disk0: / asdm - 623.bin
ASDM location Camille 255.255.255.255 INTERNAL
ASDM location INTERNAL CGT-external 255.255.255.255
ASDM location INTERNAL SITE1-LAN 255.255.0.0
ASDM location INTERNAL SITE2-LAN 255.255.0.0
ASDM location INTERNAL training3-LAN 255.255.0.0
ASDM location INTERNAL training3 - ASA 255.255.255.255
ASDM location INTERNAL GDO 255.255.255.255
ASDM location INTERNAL SITE1 - ASA 255.255.255.255
ASDM location INTERNAL SITE2 - ASA 255.255.255.255
ASDM location INTERNAL training3-VOICE 255.255.0.0
ASDM location puppy 255.255.255.255 INTERNAL
enable ASDM historyI should also mention that my test clients are a combination of Windows XP, Windows 7, and Windows Mobile. Other that in specifying the preshared key and forcing L2TP/IPsec on the client side, the VPN settings on clients are the default settings with the help of MS-CHAP/MS-CHAPv2.
You must configure * intercept-dhcp enable * in your group strategy:
attributes of Group Policy DefaultRAGroup
attributes of Group Policy DefaultRAGroup
Server DNS 192.168.10.4 value
Protocol-tunnel-VPN l2tp ipsec
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list DefaultRAGroup_splitTunnelAcl
value by default-domain somewhere.comIntercept-dhcp enable
-Latptop VPN clients (which I assume are on windows computers) is also the * use on remote network default gateway * box unchecked. It is located on the Advanced tab of VPN client TCP/IP properties. Select Client VPN > properties > Networking > TCP/IP Internet Protocol > properties > advanced and uncheck the box.
Alex
Maybe you are looking for
-
From the outset, I am on a MacBook Air, running Yosemite & the most recent Firefox Help. If your only interest in my question is for bash Macs, then (yawn) I'm not interested. If your interest is to help sincerely, then you have my interest as well:
-
I have the new laptop. Dell Inspiron. Using the latest version of Windows 10 with the latest version of Itunes installed. My ipod is earlier using iOS 5.1.1. When it is plugged into a usb port on the computer, the computer does not even recognize tha
-
Can I disable Audio microphones HF of the G20
Hello I use this camera to flow and I have a separate audio setup. I would like to cut all the audio from the built-in camera microphones through the hdmi cable I use for video. I can't find how or if I can do it. Is this possible? Thank you Stephen
-
Bij het updaten van KB950974 komt 0 x 80070008 foutmelding hoe you hertstellen?
Update automatic van het bij programma KB950974 squeeze foutmelding ik 0 x 80070008.Said zou Hotel komen door you weinig schuifruimte maar deze is ruim Roken.Foutmelding is voor het first Café nagaoui er een algeheel system had place d op 5 December
-
I noticed that my remote access has been activated twice in a week but I did not. no way to verify when, what, who activated via the event log,...?