LabVIEW 2012 Setup error

Similar Questions

• LabVIEW 2012 Installation error connecting to the server

  I'm trying to reinstall LabVIEW 2012 after I.S. replaced my laptop.  The new laptop is not a DVD, so they transferred the DVD and transferred the files from the DVD to a folder on my desktop.

  I select the option connect to OR check my serial number, enter it and select "Next >."  I immediately get an error message saying "an error has occurred on the server.  You want to try again? »

  It is that I can get.  If I click 'Yes', I get the same error.  Can someone point me in the right direction?

  (There is a Windows 7 computer)

  Thank you

  oxfat

  Oxfat,

  There could be some problems going on because of the age of the installation of LabVIEW and physical media that it is installed from. I think the process easier for you to generate an activation code based on your serial number you can do with this site:

  http://Delta.NI.com/nilg-activate/JSP/customer_activate_details.jsp

  In addition, here are some other options during activation if you always encounter errors:

  https://www.NI.com/license/product_activation.htm

  Finally, here's official National on activation in case tool tutorial you want to send this to your business in order to avoid future problems:

  http://www.NI.com/white-paper/11039/en/

• SQL SERVER 2012 SETUP ERROR

  I have an exe separated for installation of SQL SERVER 2012.

  During the Installation of SQLManagementStudio_x64_ENU.exe , an error occurs. Please see below.

  What could be the possible solution or work around it?

  I really need to install it, I have loads of work to do. Please :( Thanks in advance for helping me.

  

  This issue is beyond the scope of this site and must be placed on Technet or MSDN

  http://social.technet.Microsoft.com/forums/en-us/home

  http://social.msdn.Microsoft.com/forums/en-us/home

• Error-63101 when executing the FPGA Interface C API Generator in LabVIEW 2012

  I'm using LabWindows CVI 2012 and 2012 LabVIEW FPGA module.  I try to use the FPGA Interface C API generator and I get the following error from a freshly generated .lvbitx bitfile.  I use the local server compiles on my PC.

  Error-63101

  NOR-RIO: A valid .lvbitx bitfile is required. If you are using a valid .lvbitx bitfile, the bitfile maybe isn't compatible with the software you use. Determine which version of LabVIEW was used to make the bitfile, upgrade your software to this version or later, and then try again.

  The problem occurs when executing CVI or LabVIEW.  I was able to do this earlier when I was compiling the FPGA in LabVIEW with the API generator 2011 downloaded from the Web site.

  A bit of weirdness in my setup, it's that I charged it off downloads from the website (latest files after 2012 NIWeek) rather than the normal distribution DVD.  I installed LabVIEW, so NI RIO, then the Xilinx tools compatible with 2012.  It works very well when you talk to the FPGA to a LabVIEW vi running on my Windows PC to the host.

  Any suggestions?

  Problem solved.  I had to download FPGA Interface C API generator 12.0.  It works now.

  I would have thought that if a product was called on the menu in LabVIEW 2012, it would be prompted to upgrade to a compatible version, when I installed LabVIEW.  The old version is not compatible with version 3.0 bitfiles, as identified on the following lines at the top of the .lvbitx file:

  
  
   3.0

• Error Code HDL with CRio RFP generation after update for LabView 2012

  Hello everyone,

  I use a CRio DP Comsoft master/slave module for my communication with a PLC system. The application worked perfectly under LabView 2011. After the update to LabView2012, I got an error message that the HDL Code generation failed. After that I've updated also the Software NI Profibus CRio in Version 1.3, but this n ' t´t solve the problem. The next step was to use the example of project code "CS_cRIO-PB_DP-MasterExample" which was delivered with the new NI CRio Profibus software. Even with this code example, the problem still exists. For detailed information on the configuration and the error message please refer to the screenshot. Any help or idea would be appreciated.

  Jürgen

  Hi Jürgen,

  I looked inside and could reproduce this error. Somehow the compiler with LV 2012 has problems with the coded 8.5.1 Subvi LV. Please use the attached VI and copy it to the following location. (\\Program Files\National Instruments\LabVIEW 2012\vi.lib\addons\Comsoft.lib\cRIO PB)

  Before do you it please close your LabVIEW.

  Then try to compile again.

  Let me know if it still does not. We are currently working on a new installer that will correct this problem.

  DirkW

• HTTP POST 2012 of LabVIEW for Mac error:-1967362015

  I'm so moving an application to a mac platform labview and I encountered some problems with the Vi HTTP Client functionality.

  The connections work well with http requests and https in the project view, but begin to fail when it is compiled into an executable file. I was able to isolate the error code-1967362015, which reads like a failed to load library error. In reading the other posts, it gave me the idea of a symbolic link libraries ni_httpclient for the folder OR, but it does not solve my problem. This would have something to do with the fact that the LabVIEWHTTPClient.lvlib see the NI_InternetTK_Core_VIs.lvlibSL.vi to be a library 'friend '?

  The vi I joined is he who tries a get or a post without ssl request and receive the same error on both when built as an executable file. It is difficult to debug because the vi client http is locked. Any help would be great!

  We were able to get telephone support OR on the issue, and it turns out it was a problem with LabVIEW 2012 on the Mac platform. The solution to the issue of the library was the following: located in the/Library/Frameworks/LabVIEW\ 12.0\ Runtime.framework/resource/ folder should be a file called ni_httpClient.framework.  Please rename this file to ni_httpClient.framework.bak.  Then re-create the executable file.

  This solves the issue of creating applications using the vi client http, but there are questions still pending building applications by using SSL.

  Thanks for the suggestions.

• DAQmx Setup error

  I have a brand new with Windows7 - 64 bit.  I installed LV 2010 RT, FPGA and all drivers. No problem.  I then installed LV 2012 with RT, FPGA, a few tools and drivers.  I got an error when installing on DAQmx.  I told him to continue.  Then, I got an error at the end saying that something was not installed correctly.  The two messages are attached below.  I have uninstalled all NOR associated and repeated.  Same result.  I can open and run LabVIEW 2010 and 2012.  I can open MAX.  However, when I attach a USB-6008 to the computer, it is said that the driver is not loaded.  MAX can't see the 6008.  Which, of course, corresponds to the Setup error.  Any ideas how can I fix?

  Thank you

  DaveT

  Hi Dave,.

  This problem is often related to anti-virus software. You have any antivirus running on your new computer software? If you do, please try to uninstall DAQmx, disable the active virus scan utility and install the drivers as administrator.

  I hope this helps! Thank you

• Internet Toolkit for LabVIEW 2012 64-bit

  I have an application which is currently written in LabVIEW 2009. It requires the Internet. I try to open it in 2012 of LabVIEW (64-bit) (using Windows 7 64-bit). LabVIEW 2012 does not find the box at Internet tools since he has been deprecated in LabVIEW 2012, so LabVIEW complains.

  So I downloaded the toolkit LabVIEW 2012 Internet and tried to install it. When the Setup program tries to run, it stops with an error message that says:

  "NEITHER LabVIEW 2012 (32-bit) or more must be installed before installing OR.
  2012 Internet Toolkit LabVIEW. »

  Can someone tell me where I can find the Internet Toolkit for LabVIEW 2012
  (64 bit)?

  Thank you

  -Ray

  Since you seem to understand that the Internet Toolkit has been deprecated, I do not understand your question. There is no 64-bit version of the tool. In fact, it has very few tools that do not have a 64-bit version. In order to use the old, 32-bit version, you must use it with the version 32-bit LabVIEW, as said the message.

• Load a file EDS into LabView 2012

  Through research I found that DeviceNet Configurator is no longer available. I'm under LabView 2012 with IndComm/Devicenet 2.2 pilot. What replaces the DeviceNet Configurator? How to load the EDS files?

  Thank you

  Tennessee Paul

  My post here on a different topic, I thought that I would wear it to conclude this thread.

  Load an EDS file to the slave device

  1. Right-click on the slave device
  
  
  2. Select "Sheet"... »
  
  
  3. Click on add files...
  
  
  4. Navigate to the location of the EDS file.
  
  
  5. Select the file.
  
  
  6. Click OK.
  
  
  7. In the left pane, expand the data sheet newly added up to reach the node displays the version.
  
  
  8. Select the version.
  
  
  9. Click OK.

  Check the device and file EDS

  1. Right-click on the slave device
  
  
  1. Select utilities
  
  
  2. Select the Panel of Test online
  
  
  2. Select the option 'Device status' in the field of category on the left.
  
  
  3. On the right, select the slave device, you want to check.
  
  
  4. Click on "check the device".
  
  
  5. Read the errors/warnings or lack thereof.

  Edit the file EDS

  To change the EDS file, I used EZ-EDS , which is a specific devicenet EDS of ODVA freeware Editor.

  I did my corrections and saved my file EDS. (After having saved my original, of course).

  Remove the installed Labview EDS file

  1. Navigate to the following location: C:\ProgramData\National Instruments\NI-IndComm for DeviceNet\Datasheet
  
  
  2. Remove the sheet (Note: there is more that one datasheet added manually.) Additional EDS files come with the IndComm driver. Find the EDS file for the specific device that you want to replace and delete).

• Legend bug XYGraph slider blocks instantly LabView 2012

  Hello!

  I'm just facing a very annoying bug.

  Please find my attached VI example, I would like to know the weather, you can confirm the bug? Run the VI if you want to see a curve (in fact the bug appears even if you put all the data on the chart, if you do, all the same) and after that try to click the cursor vertical scroll bar legend to scroll upwards or downwards to see the cursor names.

  It instantly blocks my full version of LabVIEW 2012 Edition: 12.0.1f2 (32 bit). This XYGraph is still blocking LabView... I can't continue with my project, now I will just try to work around the error, I'll try to remove the sliders and then add them again...

  In any case, a very strange and very annoying behavior...

  Anyone could repeat the same bug?

  Thanks for the support!

  The reason for the accident seems to be duplication of the cursor "Gas_inject." There are four times. Using the property node 'CursorList' to remove these duplicates made the VI DO NOT crash when you move the vertical scroll bar of the legend of cursor.

  To simplify:

  Read the CursorList first, remove any duplicated the table manually in the indicator (right-click on the element > data operations > Delete Element). The change to a control, change the property node to write and run the VI once.

  Norbert

• Impossible to install labview 2012

  I try to install labview 2012 on my 64 bit Windows 7 system, but fails;

  Here are the symptoms:

  (1) I click setup.exe directly and it shows that:

  

  (2) if I run it with the administrator, it appears that:

  

  (3) I checked that I can execute another exe file...

  Thank you

  Hi Bestchun,

  It could be a damaged Setup file. Try to re - please download the installer of ni.com/downloads.

  I will follow this post, answer so if this does not work for you.

  N

• The connection failure module 9795 with wsn-3226 with Labview 2012

  Good afternoon

  I have a Crio-9074, with a 9795 module and two modules WSN-3226 and I have updated my Labview to the latest version, version 2012 and me cannot communicate with WSN nodes. The program says that the nodes cannot connect with the gateway. The software I have installed is:

  -Labview 2012

  NOR-Rio 12.0

  NOR-WSN 1.4

  -OR-Real-Time Module 2012

  I checked CRio don't let install WSN host API 1.4.0 because it is not installed in my host. Can someone tell me where I can download it, and if this is the reason why I can't communicate with nodes?

  Thank you for your time

  Hello

  I have

  LaurentV wrote:

  Hello

  Make your cRIO and all modules appear in MAX?

  Could you give more details about the problem, such as a screenshot of instructions on how to reproduce the problem, and you get the error message?

  ---

  Lawrence V.

  Engineering Application OR (France)

  correction of the error, by reinstalling Labview 2012. Thank you very much for your attention.

• LabVIEW 2012 do not open

  My LabVIEW 2012 opens with a message that says operation side by side is not configured correctly.  I tried to open LabVIEW 2011 and he opened and I don't see the message, but it was very slow, as it opened.

  Before seeing the error, I did a repair on my Package redistributable Microsoft Visual C++ 2010 (x 86) and on my 4.5 .NET.  What is the best way to solve this problem?

  Thank you!

  I did a lot of installation and uninstall of Microsoft Visual C++ distributable, and which does not solve the problem.  I also did a repair for the 2012 of LabVIEW.  Later, I look at the event log, and who told me the LabVIEW.exe.config file.  I made the following change below, and that fixed the problem.  I don't know why but.

  LabVIEW.exe.config that caused the error

  
  
  
  
  
  

  LabVIEW.exe.config as the error correction

  
  
  
  
  

• VI LabVIEW 2012 script: Method - delete not yet implemented framework

  Hi all

  I use screws LabVIEW 2012 script to delete the events to the event structure. For some reason, I get the following error

  

  Is it possible that a method is listed without running? Suggestions to overcome this is welcome. Thanks in advance

  Kind regards

  S.P.Prasaanth

  According to this http://forums.ni.com/t5/LabVIEW/Remove-Frame-Not-Implemented/m-p/2100644/highlight/true#M684629 post: Yes, it can be.

  But it seems that implemented in LV2013: http://forums.ni.com/t5/LabVIEW-Idea-Exchange/Configure-Event-Case-with-Scripting/idc-p/2523818/high...

• Why LabVIEW 2012 does not support USB-6009?

  Hi all

  I recently installed LabVIEW 2012 and DAQmx 9.6 (and also tried with latest version) in my PC with Windows 7. I have the version of Explorer 5.4 measure and automation. I'm working with hardware DAQ USB 6009. Everything seems compatible, but when I try to post data acquisition, it fails. However, I used to use this device (since I bought it last year) with the other PC that has the Windows XP operating system and the older version of LabVIEW 8.5.

  What can I do with LabVIEW 2012 is a message "a 88302 error has occurred." and "This could be an internal error."

  If someone has an idea to solve the problem, please let me know.

  devkotaj

  Hi devkotaj,

  The USB-6009 device should work perfectly on Windows 7 with the software you have listed. This looks like a problem of configuraiton of material for me.

  What are you trying to do when you receive the error 88302? This error usually indicates a corrupt DAQmx driver, which may result from the installation of several DAQmx versions on the same machine. Have you tried repairing your installation DAQmx? I could uninstall DAQmx from the Control Panel before installing the latest driver. You can see our procedure to reinstall or uninstall recommenedd here.

  I hope this helps!

  Andy C.

  Engineering applications

  National Instruments